Unable to connect to the provider Services

Similar Questions

• Unable to connect to the web services server

  Unable to connect to the web services server.  It is a common error that you might see if you try to enable web services.  If you receive this message, try the following steps.

  For Officejet printers

  1. open the internet browser type printer IP address.

  2 should bring you to the status of the printer page.

  3. Select the tab network at the top.

  4. left side select IPv4 under wireless.

  5. under DNS address Configuration select manual DNS server.

  6. for favorite enter 8.8.8.8

  7. for alternate enter 8.8.4.4

  8. Select apply. You can get a warning saying that this could break the connection which is very good.

  9. turn the printer off for about 30 seconds and then try to enable web services.

  For Photosmart printers

  1. Enter the printer's IP address in a browser.

  2 Select the network at the top of the page.

  3. on the left, select network.

  4. Select Network (IP) address

  5. select manual DNS server

  a. manual Preferred DNS should read 8.8.8.8

  b. alternate DNS server should read. 8.8.4.4

  6. Select apply you could get a fair warning select OK

  I hope this helps!

• Pavilion 140 550 - t: unable to connect to the windows service

  Not sure if it's the good advice of post, but here goes.

  Just got the HP computer yesterday and installed Norton Security, Malwarebytes, and Windows Live Mail (do not like the version of Mail). Now, when I start it, I get "Unable to connect to the Windows Service" pop up and WLM crashes when I try to open it. What the DEVIL?

  Had the same problem on the one I just replaced. My laptop became the 'Group Policy' error thing, but I think I fixed it.

  Any suggestions? Windows is a joke!

  If it is Norton Security, then it's a firewall as well and firewalls blocking things, it's that they are supposed to do. So demand for three, you said that this is probably the cause.

  But if you do not want to test it, then try the system restore I've mentioned or reload the image origin, then just put in place the email again and see if it works without the other two installed, first to see if it will work with anything else in the picture.

• Unable to connect to the wifi service in my house, how can this be repaired?

  I have a dell laptop and I am trying to understand how to do this.  I enter the key of the service network and the message says that the network password must be 40-140-bit according to your network. It can be entered as ascii characters 13-5 or 10-26 hexadecimal characters? How can this be repaired?

  Hi Vickiloo06,

  ·         Did you do changes on the computer before the show?

  ·         What happens exactly when you try to connect to the wifi service, you receive error message?

  I suggest you to consult the following Microsoft Knowledge Base article and check if it works.

   

  Unable to connect to an access point wireless with Wi - Fi Protected Access update installed

  http://support.Microsoft.com/kb/821442

   

  How to troubleshoot wireless network connections in Windows XP Service Pack 2

  http://support.Microsoft.com/kb/870702

  I hope this helps.

• HP ENVY 4-1200 ultrabook: unable to connect to the windows service

  I got this notebook for a week, it has started to come on the screen at startup * unable to connect to windows. Windows could not connect to the group. Political Clent. This problem prevents standard users connect * did anyone know what I can do about it at the start. Thank you

  Please try the fix described below:

  

  If you found my answer helpful please say thank you by clicking on the icon of the thumb.
  If my answer has solved your problem, please mark it as accepted Solution. Thank you!

• Unable to connect to the Web Services Proxy/unused (a HP 7500 JO)

  Hello

  Here's the situation:

  Previous installer:

  .  I have connected my 7500 for the corporate network (IP = 172... series)

  .  registered the product with ePrintCenter

  .  used a PC under Windows to print (and scan) with the printer

  .  web proxy entry "webproxy.phila.gov".

  .  However, because homeland security rules, I could never work, so I just let it go

  Current situation

  .  has taken the home printer and set up on my home network, i.e.,.

  -using the 192.168.xx.xx series

  -Router broadband Netgear ' G' (1 years) set up at the 192.168.xx.254

  -SSID & encryption assigned

  -printer, the value 192.168.xx.155 (static IP address, the subnet and the gateway assigned as well)

  -My DNS is identical to the bridge and it works fine for all the internet access to this day

  -with the help of a PC and a Macbook Air to print and scan and everything works fine

  .  HOWEVER,.

  -Initially, 'web services' were active (carried over from when I was on the company neetwork?)

  ..  Are looking for, found and downloaded updates

  -When I went to hp.com ePrintCenter he showed the product as 'registered '.

  ..  He would'nt I would like to connect (with a name and a password I had used previously), or create a new account

  ..  I never remember getting an email address of the printer

  ..  and I had never been able to send anything to the printer to print because of my problem of network security

  -Yes, after trying all sorts of things, I:

  ..  I tried to get another email without success

  ..  tried to re - enable web services, but he said I need to 'proxy', and I discovered that he had always "webproxy.phila.gov."

  ..  I have reset the values by default web services and network values

  ..  I put the static IP address return address in (i.e., printer, subnet and gateway (it has nowhere to put in a DNS one))

  ..  printing and scanning to 192.168.xx.155 works fine

  ..  From my iPad AirPrint works very well

  .  BUT, I still can not online and therefore web server, web services are not enabled, therefore not ePrint

  -everytime I try, it says it needs a proxy

  - but I don't have a proxy installed on my internal home network bit

  -Comcast/Xfinity, my ISP, do not use a proxy

  So, I'm dead in the water.  I can't figure out how to get the web services enabled; I do not use a proxy, so I don't know how to go beyond this issue. How to regenerate address of the printer; and so, how do I connect an account on the ePrintCenter (or get them to send me my old account information).  I'm dead in the water and cannot use a feature most of my printer that I desperately want to be put in place and functional.

  Any help would be greatly appreciated!

  Tommy

  Problem solved, but I don't know exactly how I did it. However, I went back in and let the printer assign the IP address. Then I turned the printer off and on again. Last I kept pressing the button "Printer e-mail address", who has repeatedly failed, but then finally went through and print the 'printer' page, I quickly used to connect to the ePrintCenter and put everything in place.
  
  Now it's working.

• Unable to connect to the windows service

  I get an error "failed to connect to windows service" started reading the forums, I see this is a relatively common mistake.  I tried several suggestions without success.  I ran SFC who has corrected a mistake.  My computer does not connect to Internet "State of the unknown connection, the dependency service or group was able to start" by other threads, I tried to look at the event log, but it will be does not seem to be running.  Looking at the services I see that the DHCP client is starts but never fill in start mode.  I checked this service dependencies; AFD for Winsock, TCP/IP, the NSI proxy service protocol driver.  None of these three shows in respect of the services, so I don't know how to check if these services are running.

  I also went on the Lenovo website and downloaded and installed the Intel chipset driver and driver Intel LAN Nineveh.

  Any suggestions?

  Hello

  1 redefine ALL services on their default values.

  Logon as ADMINISTRATOR

  BlackViper - Vista Services
  http://www.blackviper.com/WinVista/servicecfg.htm

  Start - type in the search box-> find Services at top - right CLICK top - RUN AS ADMIN

  2. switch to update or re - install the NIC (network card) and WiFi (wireless) drivers from the Lenovo site.
  Check with Lenovo support, their drivers and documentation online and ask in their forums for
  known issues.

  Support from Lenovo and downloads
  http://www-307.IBM.com/PC/support/site.WSS/homeLenovo.do

  Lenovo forums
  http://forums.Lenovo.com/

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Error: [REP_55102] unable to connect to the service of filing [BIA_RS]

  Hi all
  
  I get this error "[REP_55102] unable to connect to the repository service [BIA_RS]" when I tried to connect to Informatica Repository Manager client to server Informatica which is insallted in another machine. When I checked the log "pmreplib.log" file, it says "ERROR: REP_51147 [Mon Feb 04 15:21:11 2013]: (7216 |)» 7680) cannot connect to the repository on the host: oracle2go, Port: 6013. ».
  
  In the background, as Informatica Server is installed in another machine, we have limits to access the ports. This is why I changed all default Informatica ports by running the below command...
  ./infasetup.sh UpdateGatewayNode-asp 5503 of na oracle2go:5501 - ap 5502 - sp - 5504 - sv 5505
  
  Although I changed ports to 5501 and 5502, 5503, 5504, 5505. I don't know why the client uses port 6013 and I don't know where this port number is coming.
  Could you get it someone please let me know how can I change this port (6013), so that I can connect the Informatica customer.
  
  Thank you
  Harish Nunn

  Hi Harish,

  On the Client Informatica Repository Manager Gateway numbers and the port are provided to connect to the repository server that runs on the given gateway and port. In your case, my understanding was that the Informatica repository is running on the 5501.

  So I think that you did not change to the port number in the administration console Informatica. So in Informatica Adminconsole node configurations change the port number to 60xx 50xx. There are 2 entrances to the repository server and the numbers of ports of the max and min of Integration Services. Once you change them restart the Services of Informatica.

  Let me know if it worked.

  Kind regards
  Jay

• Unable to connect to SmartView provider error

  
  Set us up production Essbase to AWS servers, but when trying to connect to Smart View essbase using native password and admin user name, he takes the username and password, but it crashes when you select Oracle Essbase and then survey the following error eventually

  Unable to connect to the provider.

  I check APS, but also other services, they are all working well. Any pointer on how to troubleshoot the error?

  Thank you

  19000 is sufficient for all web applications, because they will be handled by the web server, for example, workspace, smart display, FR. Essbase studio not falling in this and if you use the studio console, you must open the port on the studio server.

  There is a good document that will provide the ports for the client to the server - http://docs.oracle.com/cd/E57185_01/epm.1112/epm_communication_flows.zip

  See you soon

  John

• SmartView error - could not connect to the provider

  So I try to create a connection in the planning application to see my all my forms of smartview

  by using the following link

  http://host.Corp.bla.com:19000/HyperionPlanning/SmartView

  but he does not accept the connection and starts the error message "unable to connect to the provider of.

  the service provider - web application on the host computer is running.

  What should I do to solve this problem.

  Is this a manual configuration? I doubt that it is. Try to start the services as usual and check the logs if there is an error.

  Concerning

  Celvin

• Unable to connect to the selected Mobile Data Service, please try again later.

  Dear all,

  I downloaded Blackberry email and MDS Services 4.1.4 and the Blackberry 9630 Simulator Simulator. I'm testing a blackberry asp.net application I have running on a test server using the blackberry Simulator.

  I have windows XP box. When I try to run the SDM Service, it runs without error, but acquire it on the site - http://www.blackberry.com/go/mobile - error saying above message - unable to connect to the selected Mobile Data Service, please try again later. How can I solve this problem, I tried to use full qualified names in the config file.

  Any ideas?

  NAV.

  Hi Nav, thanks for your message.

  When you use the BlackBerry 9630 Smartphone Simulator, you may need to change its default connection settings in order to provide network connectivity.  The reason why because the 9630, being a world phone, supports different types of network technologies and a configuration change may be needed to make it work with the MDS Simulator - CS.

  1. from the home screen, click the 'manage connections '.

  2. a popup window opens, select "Mobile Network Options '.

  3. in the options screen, ensure that the following field values are defined:

  • Data services = 'On '.
  • Network selection mode = "auto".
  • Technology network = "1XEV".

  4. close the 'mobile network options' screen to save the changes

  9630 smartphone Simulator should now have network connectivity.

  Sincerely,

  Adam

• Reinstalled XP and now unable to connect to the internet, dsl provider says the leaves to reinstall the connection LAN how fix this?

  Original title: windows xp.

  reinstalled xp and now unable to connect to the internet, dsl provider says the leaves to reinstall the connection LAN how fix this?

  Hello

  Go to the website of your computer manufacturer > drivers download Section > put your computer model number > operating system > Search adapter network, pilots etc. for her.

  Get graphics, sound while you're there.

  You should always do a reinstallation.

  Use the computer that you use to make the foregoing > download and save in this office > copy of Flash Drive > then install in another computer.

  See you soon.

• After a virus, I am unable to connect to the internet. Event log messages: the NetBios over TCP/IP service failed to start due to the following error...

  original title: NETBios TCPIP of missing in Device Manager

  I recently had to run two antivirus programs on an infected computer and am now unable to connect to the internet. When I went to the event viewer, I noticed the following error messages:

  Event type: error

  Event source: Service Control Manager

  Event category: no

  Event ID: 7000

  Date: 16/01/2012

  Time: 12:31:17

  User:                       N/A

  Computer: JARRIOUSSTUDIO

  Description:

  The NetBios over TCP/IP service failed to start due to the following error:

  The service cannot be started, either because it is disabled or because it has no enabled devices is associated to him.

  Event type: error

  Event source: Service Control Manager

  Event category: no

  Event ID: 7001

  Date: 16/01/2012

  Time: 12:31:17

  User:                       N/A

  Computer: JARRIOUSSTUDIO

  Description:

  The DHCP Client service depends on the NetBios over TCP/IP service which failed to start because of the following error:

  The service cannot be started, either because it is disabled or because it has no enabled devices is associated to him.

  Event type: error

  Event source: Service Control Manager

  Event category: no

  Event ID: 7001

  Date: 16/01/2012

  Time: 13:32:01

  User:                       N/A

  Computer: JARRIOUSSTUDIO

  Description:

  The DHCP Client service depends on the NetBios over TCP/IP service which failed to start because of the following error:

  A device attached to the system does not work.

  Event type: error

  Event source: Service Control Manager

  Event category: no

  Event ID: 7001

  Date: 16/01/2012

  Time: 13:32:01

  User:                       N/A

  Computer: JARRIOUSSTUDIO

  Description:

  The helpdesk TCP/IP NetBIOS depends on the NetBios over TCP/IP service which failed to start because of the following error:

  A device attached to the system does not work.

  When I look in the Drivers folder, I see netbt, but devices & Non Plug and Play Devices, of TCPIP NETBios is not listed in Manager.

  Hi Diddy Dell,

  Follow these methods.

  Method 1: Performs a search using the Microsoft safety scanner.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

  Method 2: Follow these steps:

  Step 1: Start the computer in safe mode with network and check if the problem persists.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  Step 2: If the problem does not persist in SafeMode with network, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click on restart to restart the computer.

  Method 3: Follow the steps in the article.

  How to reset the Protocol Internet (TCP/IP)

  http://support.Microsoft.com/kb/299357

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

• Unable to connect to the web proxy/services

  Unable to connect to the web proxy/services used for officejet pro 8600 as well as using verizon fios actiontec router.  I tried wireless and ethernet.  Connectivity seems good.

  Resolved.  Port forwarding blocked by another application of verizonwebcamera problem.

• Error message: "unable to connect to a windows service windows could not connect to the system event." Unable to connect to the network, Windows Vista Home Edition

  Hello

  When I start my laptop there is a long pause between the home screen and the cover page of my office where the message "unable to connect to a windows service windows has no can connect to the system event. I am unable to connect to networks as says "the dependecy service or group could start. I checked some of the solutions to this problem, including the execution of the 'netsh reset winstock' program that did not work. Any advice would be very helpful. Thank you.

  Hello

  It would be a good idea to run the System File Checker tool to see if you have corrupted files

  "How to use the System File Checker tool to fix the files on system missing or corrupted on Windows Vista or Windows 7"

  http://support.Microsoft.com/kb/929833

  Use the (SFC.exe) System File Checker tool to determine which file is causing the problem and then replace the file. To do this, follow these steps:

  1. Open an elevated command prompt. To do this, click Start, click principally made programs, Accessories, right-click guest, and then click run as administrator. If you are prompted for an administrator password or a confirmation, type the password, or click allow.
  2. Type the following command and press ENTER:
     sfc/scannow

     The sfc/scannow command analyzes all protected system files and replaces incorrect versions with appropriate Microsoft versions.

  ___________________________________________________

  And Malware scan:

  Search for malware, if necessary using the safe mode with networking.

  http://www.bleepingcomputer.com/tutorials/how-to-start-Windows-in-safe-mode/#Vista

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap the F8 key repeatedly until you are presented with the Boot Options Advanced Windows Vista.
  3. Select the Safe Mode with networking with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  Then, download, install, update and scan your system with the free version of Malwarebytes AntiMalware in Mode safe mode with networking:

  http://www.Malwarebytes.org/products/malwarebytes_free

  See you soon.