Unable to connect to the web proxy/services

Similar Questions

• Can 'connect to the Web (proxy) service.

  Hello
  
  I use JDev 11.1.2.3.0 and the integrated WebLogic server (10.3.5.0).
  I am trying to deploy a Fusion Webapp (ADF) which needs to connect to an external Web service (so it is not in my local network).
  I use a proxy and I entered all the information in the boot parameters in my WebLogic (Tools > Preferences > Web & Proxy) and successor to the power of Attorney 'Test '.
  But when I try to log into my webservice (so when start my weblogic and deploy my application), the webservice does not even get my connection request.
  I'm I missed something? Or is it somehting wrong with the settings of my laptop?

  http://StackOverflow.com/questions/120797/how-do-i-set-the-proxy-to-be-used-by-the-JVM - try this add the implementation for your project options

• Unable to connect to the web services server

  Unable to connect to the web services server.  It is a common error that you might see if you try to enable web services.  If you receive this message, try the following steps.

  For Officejet printers

  1. open the internet browser type printer IP address.

  2 should bring you to the status of the printer page.

  3. Select the tab network at the top.

  4. left side select IPv4 under wireless.

  5. under DNS address Configuration select manual DNS server.

  6. for favorite enter 8.8.8.8

  7. for alternate enter 8.8.4.4

  8. Select apply. You can get a warning saying that this could break the connection which is very good.

  9. turn the printer off for about 30 seconds and then try to enable web services.

  For Photosmart printers

  1. Enter the printer's IP address in a browser.

  2 Select the network at the top of the page.

  3. on the left, select network.

  4. Select Network (IP) address

  5. select manual DNS server

  a. manual Preferred DNS should read 8.8.8.8

  b. alternate DNS server should read. 8.8.4.4

  6. Select apply you could get a fair warning select OK

  I hope this helps!

• Unable to connect to the virtual disk Service, Virtual Disk Manager Interface not registered

  I installed Windows 7 Ultimate on this laptop as a new installation about six months ago.  Since then, I don't think I ever ran diskmgmt.  Today, I joined a new external hard drive usb, it reported the drivers installed fine, but then the installation bombed at the beginning.  I went to verity, what had happened and has run diskmgmt.msc (as an administrator), but she came back with the message "Unable to connect to the virtual disk Service" and also a small OK msgbox appeared with the title "Virtual Disk Manager" and the "Interface not registered" message

  I disconnected the USB hard drive and tried again diskmgmt, but no change.

  I restarted in safe mode, tried diskmgmt, but no change.

  I ran sfc/scannow, but it has reported that it found no errors.

  I checked that the virtual disk service has been configured as a textbook in services.msc, and event viewer showed that when I ran diskmgmt he started VDS and then stopped VDS.

  I tried again, but still not like before.

  Is there some dll I can't regsrv32?

  Thank you

  Marc

  Hello

  I suggest you to return the items for the following responses from Microsoft, he says same issues with trying the troubleshooting steps and check if it helps.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-hardware/cant-start-disk-management-unable-to-connect-to/31898500-9d84-4CB5-9ba3-c1f42e3b1ace

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-hardware/problems-with-Vista-after-unplugging-by-external/093f1660-160F-478f-b81a-493e963ffd9a

  http://TechNet.Microsoft.com/en-us/library/cc771775.aspx

  Note: it also applies to Windows 7.

  Hope the information is useful.

• Unable to connect to the Web sites security and microsoft, but internet is not working properly

  Can anyone help?
  Now, this is getting very frustrating.
  I can connect to the internet and browse most Web sites. My email works fine but I can't connect to websites www.microsoft , Norton is 'unable to connect to the Live Update server, check the internet connection' and my media center can't find my internet connection.
  What is going on?
  I have a subscription to Norton who can't find any problems. I also downloaded onecare and trojan remover, returning with a clean report.
  Please help before I go out what remains of my hair.
  What about Frank

  Hello

  You can access Microsoft.com, McAffee.com, Symatec.com? Thinking you have a conficker.

  Check with this site
  http://www.confickerworkinggroup.org/infection_test/cfeyechart.html

  Alert on the Win32/conficker virus
  http://support.Microsoft.com/kb/962007

  Protect yourself from Conficker
  http://www.Microsoft.com/security/worms/Conficker.aspx

  How to remove the worm Downadup Conficker (Uninstall Instructions)
  http://www.bleepingcomputer.com/virus-removal/remove-Downadup-Conficker

  How to manually remove the Conficker worm
  http://www.411-spyware.com/Conficker-worm-removal#how-to-remove

  BDTool to remove
  http://www.bdtools.NET/

  -----------------------------------------------

  Run the malicious Microsoft removal tool, scan with Malwarebytes, Prevx to be sure you know all the
  malware involved and if necessary use UnHackMe.

  Start - type in the search box-> find MRT top - right on - click RUN AS ADMIN.

  You should get this tool and its updates via Windows Update - if necessary, you can download it here.

  Download - SAVE - go where go out you there - top - right click RUN AS ADMIN
  (Then run MRT as shown above.)

  Malicious removal tool from Microsoft
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=en

  Malwarebytes - a scanner at the request - update on the updates tab and run whenever you think malware.
  http://www.Malwarebytes.org/

  Here are some free online scanners to help the

  http://www.eset.com/onlinescan/

  http://www.Kaspersky.com/virusscanner

  Other tests free online
  http://www.Google.com/search?hl=en&source=HP&q=antivirus+free+online+scan&AQ=f&OQ=&AQI=G1

  also install Prevx to be sure that it is all gone.

  Prevx - Home - free - small, fast, exceptional CLOUD protection, working with other security programs. It comes
  a scan only, VERY EFFICIENT, if it finds something to come back here or use Google to see how to remove.
  http://www.prevx.com/

  Choice of PCmag editor - Prevx-
  http://www.PCMag.com/Article2/0, 2817,2346862,00.asp

  --------------------------------------------

  Also do to the General corruption of cleaning.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Run checkdisk - schedule it to run at the next startup, then apply OK then restart your way.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------

  Run Malwarebytes when you can.

  IE - Tools - Internet Options - Advanced - tab click on restore, and then click Reset - apply / OK

  IE - Tools - Internet Options - Security - reset all Zones by default level - apply / OK

  Close IE

  IE - tools - manage Addons (for sure disable SSV2 if it is there, it is no longer necessary but Java always install
  "(and it causes problems - you never update Java to go back in and turn it off again)." Search for other possible problems.

  Windows Defender - tools - software explore - look for problems with programs that do not look right. Permit
  are usually OK and "unauthorized" are not always bad. If in doubt about a program to ask about it here.

  Could be that a BHO - BHOremover - free - standalone program, needs no installation, download and run - not all
  are bad, but some can cause your question. (Toolbars are BHO)
  http://securityxploded.com/bhoremover.php

  Startup programs
  http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.html

  Don't forget to do:

  Logon as administrator

  Start - type in the search box-> COMMAND - find on the list above - CLICK RIGHT - RUN AS ADMIN

  Enter each of these one at a time and press ENTER after each

  ipconfig/flushdns

  nbtstat-r

  nbtstat - RR

  netsh int Reinitialis

  netsh int ip reset

  netsh winsock reset

  Reset
  ------------------------------------------------------

  Here are a few rootkits if it were a question:

  SpyDLL Remover - free
  http://securityxploded.com/spydllremover.php

  Advanced Windows Service Manager
  http://securityxploded.com/winservicemanager.php

  Run the Rootkit Revealer - free
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb897445.aspx

  UnHackme - trial
  http://www.Greatis.com/UnHackMe/

  This shows how to use UnHackme and includes a link to version 2.5 – use it as a guideline and current
  available as version above is 5.5
  http://safecomputing.umn.edu/guides/scan_unhackme.html

  IceSword - free
  http://www.AntiRootkit.com/software/IceSword.htm
  Instructions and pictorial
  http://securityxploded.com/IceSword.php
  Tutorial for use of IceSword
  http://translate.Google.com/translate?hl=en&SL=zh-CN&u=http://soft.zol.com.CN/2004/0803/145163.shtml&prev=/search%3Fq%3Dicesword%26hl%3Den%26lr%3D

  Revo Uninstaller - free
  http://www.revouninstaller.com/

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• Unable to connect via the Web client

  Dear team,

  Web customer service is installed on the SSO Server (SSO installed on seprate VM), since last year 1 it works very well, but as of today I m not able to connect through webclient get below error

  https://SSO.test.com:9443 / vsphere client / #.

  Unable to connect to the server vCenter Single Sign On https://SSO.test.COM:7444/ims/STSService? wsdl .

  Note: I am able to connect VC via vsphere client but not to Web client.

  concerning

  Mr. VMware

  After you restart the WebClient service, wait 5 minutes. Now, I m able to connect VC via the web client.

  Thanks for all the help and support.

• Laptop has virus and still unable to connect to the Web site after his withdrawal.

  Original title: laptop cannot connect to router

  my daughter portable computer had bankerfoxa virus I think that I got rid of but she still can't connect on the website I want to download microsoft security essential on his cell phone how if I can not connect? pls help

  Hi trinidadg,.

  Also try the following steps, you have a problem connecting to the Web sites.

  Try to do a System Restore to an earlier date when your computer was working well and try to run a scan for malware removal.

  Try to reset the Proxy settings to connect to the internet, as some malware enable proxy settings that block your ability to browse Internet sites.

  To reset the Proxy settings:

  Click Start-> in "search programs and files" type CMD-> in the programs in the list right click CMD and click 'run as administrator '.

  In the command prompt, type the following and press ENTER:

  NETSH WINHTTP RESET PROXY

  Restart the computer

  Touhami

• Unable to connect to the web.

  I have an Inspiron One 2305. Yesterday morning, everything was fine. Before noon I couldn't connect to the web. The network connection shows that I am connected. I always get an error "unable to connect to the page. I ran anti-virus and malware. Still nothing. Do a system restore I can connect on a single page. Try to leave this page and I get the same error. Can someone give me an idea?

  At this point you can repair or reinstall Win 7. Make sure that all of your personal files are stored on a medium firstexternally.

  To do a repair, you will need your reinstall Dell Win 7 drive. Start with a hard disk check

  • Click Start > run
  • Type: chkdsk c: /f
  • Click OK
  • Accept offer to run chkdsk at the next startup, and then restart. CHKDSK runs before Windows loads. Be patient as this can take some time, depending on the size of your hard drive.

  Unlikely that chkdsk will solve the network problem, but check it anyway...

  Then run a check of Windows system (CFS) files:

  • Click Start > run
  • Type: sfc/scannow
  • Click OK
  • Insert the Dell Windows reinstallation disc, if/when requested
  • Restart when done
  • Check again networking

  If this does not help, make sure that your files are backed up! Restart, and then press F8 before Windows loads. Look for the option of repair that may be on an advanced options menu. Follow the prompts. See if that solves network problems. And don't forget to visit the Windows Update site and reinstall all updates that are missing after the repair.

• Unable to connect to the VMware Research Service - the SSL certificate verification failed

  Hello world

  to implement the new vCSA 5.1 but I get an error when you try to connect via browser Web Client.

  "Impossible to connect to the VMware Research Service . https://xxx.xxx.xxx.xxx:7444/lookupservice/sdk - The SSL certificate check failed. »

  I've found this KB

  http://KB.VMware.com/selfservice/search.do?cmd=displayKC & docType = kc & externalId = 2033338 & sliceId = 1 & docTypeID = DT_KB_1_1 & dialogID = 423540040 & StateID = 1% 200% 20423538503

  The manual/work around seems to be a lot of work for me and perhaps this will cause other problems in the service due to problems of certification :/

  I also think that this cannot be the solution for a whole new vCSAppliance...-_-

  I am also able to go to https://xxx.xxx.xxx.xxx:9443 / admin-app

  is it correct for the device?

  You need to regenerate the certificate for Server Appliance after change of IP/hostname.

  Visit this link: http://www.virtual-blog.com/2012/09/failed-to-connect-to-vmware-lookup-service/

  Also, the admin/management interface is https://: 5480

  Lack of credentials [root/vmware]

  HTH

• Unable to connect to the web interface TCS

  Hello, I'm having a problem with a TC who left the factory of S5.3 current version. I can RDP into the Windows operating system without problem and access the web page of the OS on the port 8098 management no problem, but if I try to connect to the web application interface I get a name of user and password error.  any IDE on what is causing the problem?  the server was running fine until after a reboot.  Thank you!

  Hi Patrick, http:///tcs/#page:login&rescue:true method is used for the local administrator to log in if for some reason any when LDAP authentication is configured on TCS and local users cannot connect.

  ARO

  Mahesh Adithiyha

• Unable to connect to the Web Client

  Hello

  It is impossible to connect to the Web Client. They receive the following error message:

  Error RSL # 29
  Error 2046

  We use vSphere 5.0 U3.
  

  Hello

  If please try kb article below and choose the right answer if it solves your problem.

  VMware KB: VSphere 5.0 Web Client does not load and displays the error message: Error # 2046 29 with RSL

  Thank you

  RAM

• Unable to connect to the Web Services Proxy/unused (a HP 7500 JO)

  Hello

  Here's the situation:

  Previous installer:

  .  I have connected my 7500 for the corporate network (IP = 172... series)

  .  registered the product with ePrintCenter

  .  used a PC under Windows to print (and scan) with the printer

  .  web proxy entry "webproxy.phila.gov".

  .  However, because homeland security rules, I could never work, so I just let it go

  Current situation

  .  has taken the home printer and set up on my home network, i.e.,.

  -using the 192.168.xx.xx series

  -Router broadband Netgear ' G' (1 years) set up at the 192.168.xx.254

  -SSID & encryption assigned

  -printer, the value 192.168.xx.155 (static IP address, the subnet and the gateway assigned as well)

  -My DNS is identical to the bridge and it works fine for all the internet access to this day

  -with the help of a PC and a Macbook Air to print and scan and everything works fine

  .  HOWEVER,.

  -Initially, 'web services' were active (carried over from when I was on the company neetwork?)

  ..  Are looking for, found and downloaded updates

  -When I went to hp.com ePrintCenter he showed the product as 'registered '.

  ..  He would'nt I would like to connect (with a name and a password I had used previously), or create a new account

  ..  I never remember getting an email address of the printer

  ..  and I had never been able to send anything to the printer to print because of my problem of network security

  -Yes, after trying all sorts of things, I:

  ..  I tried to get another email without success

  ..  tried to re - enable web services, but he said I need to 'proxy', and I discovered that he had always "webproxy.phila.gov."

  ..  I have reset the values by default web services and network values

  ..  I put the static IP address return address in (i.e., printer, subnet and gateway (it has nowhere to put in a DNS one))

  ..  printing and scanning to 192.168.xx.155 works fine

  ..  From my iPad AirPrint works very well

  .  BUT, I still can not online and therefore web server, web services are not enabled, therefore not ePrint

  -everytime I try, it says it needs a proxy

  - but I don't have a proxy installed on my internal home network bit

  -Comcast/Xfinity, my ISP, do not use a proxy

  So, I'm dead in the water.  I can't figure out how to get the web services enabled; I do not use a proxy, so I don't know how to go beyond this issue. How to regenerate address of the printer; and so, how do I connect an account on the ePrintCenter (or get them to send me my old account information).  I'm dead in the water and cannot use a feature most of my printer that I desperately want to be put in place and functional.

  Any help would be greatly appreciated!

  Tommy

  Problem solved, but I don't know exactly how I did it. However, I went back in and let the printer assign the IP address. Then I turned the printer off and on again. Last I kept pressing the button "Printer e-mail address", who has repeatedly failed, but then finally went through and print the 'printer' page, I quickly used to connect to the ePrintCenter and put everything in place.
  
  Now it's working.

• Unable to connect to the Web site

  I can get www.calphalon.com to load but am unable to connect. When I created the account, calphalon did exactly the same thing ebay-t - it does not recognize the security code even if it is correct. I did exactly what I do on Ebay when I ask a question to a seller - I use Internet Explorer. You have created calphalon account no problem and am able to sign in and out of my account without any problem with IE, but when I switch back to FF (updated 22), this is a go. With FF, the sign of the popup box is much too small and is completely empty. When I go to the tab of the client service to register a product (this is why I am on the site), I filled up on the sign in info on the page and the kickoff, nothing happens. It's as if I never hit the Send button. It does not seem to convey anything at all. I have signed up for newsletters, but cannot access my account on ff so it seems I'm going w/IE when I get on this site.

  Hello

  Many issues of the site can be caused by corrupted cookies or cache. To try to solve these problems, the first step is to clear cookies and cache.
  Note: This will be you temporarily disconnect all sites, you're connected to.
  To clear the cache and cookies to do the following:

  1. Go to Firefox > history > clear recent history or (if no Firefox button is displayed) go to tools > clear recent history.
  2. Under "Time range to clear", select "all".
  3. Now, click the arrow next to details to toggle the active details list.
  4. In the list of details, see the Cache and Cookies and uncheck everything.
  5. Now click the clear now button.

  More information can be found in article to clear your cache, history, and other personal information in Firefox .

  This solve your problems? Please report to us!

  Thank you.

• Unable to connect to the Web Microsoft sites (check the proxies - error ox80072efe)

  original title; everything works well for a few years then the error codes that appear are useless they just told me to check my proxy server settings.

  Everything works well for a few years, then all of a sudden I can't update or connect to the microsoft web sites at all (or very little) and when I get error codes help is useless... I just tells me to check that my proxy servers to allow windows to microsoft... not an expert but tried and it didn't work... everything else seems to work it's just like something does not want me to use the upgrade of windows... Error code ox80072efe is one of the codes... help would be welcome thanks.

  Hi andydavies863,

  1. what web browser do you use? If you use Internet Explorer, then what version of IE are you using?

  2. you remember to make changes to the computer, after which the issue started?

  3. What is the error message that is accurate and complete that you get when you try to connect to the Microsoft Web sites?

  4. is the problem isolated to specific or all Microsoft Microsoft Web sites websites only?

  5 have. what measures you taken to change the proxy settings?

  I suggest you try the steps from the following links in the article and see if it helps:

  You may encounter temporary connection related errors when you use Windows Update or Microsoft Update to install updates

  I hope this helps.

• Connection to the Web (KSOAP2) service error

  Hi all

  I developed a BB app that connects to a Web service in our company. I'm using ksoap2 to communicate with the service. Here's my problem: the application works very well on an AT & T "BOLD", but when one of my customers in the United Kingdom trying to run the same application on his "BOLD" of Vodafone, there is the following error message:

  Error of verified accounts!  Details:

  Expected: START_TAG {http://

  Schemas.xmlsoap.org/SOAP/

  {envelope /} envelope

  {positionTART_TAG}@ 02:44 in

  ( java.io.InputStreamReader@d9ad3d7c)

  Here is the info on two phones:

  Version of brand Vodafone "BOLD" - o/s v4.6.0.162 (Platform 4.0.0.155) - 1.0.102.63

  Version of Branding AT and T "BOLD" - o/s v4.6.0.167 (Platform 4.0.0.157) - 1.0.102.142

  Any help will be greatly appreciated.

  Thank you

  Read Pazmino

  in response to the OP:

  START_TAGmeans that your ksoap2 Analyzer receives a message html, most likely an error from the Web server. most common would be a 401 authorization required, but others are also possible.

  ksoap2 cannot handle http errors, you must expand its features (or live with it). improve download the ServiceConnectionMidp of the class of the ksoap2 and extend it.