Unable to connect wireless only via Ethernet cable

Similar Questions

• I want to thank my wifi in another part of the House with an Airport Extreme. But I want to not be connected to the modem main via ethernet cable is it possible?

  I want to thank my wifi in another part of the House with an Airport Extreme. But I want to not be connected to the modem main via ethernet cable is it possible?

  I put in place already to extend the wifi of my modem still connected to the modem via ethernet cable.

  Now I want to be considered on the floor and use it to extend the wifi without ethernet cable

  The AirPort Extreme can extend only wireless signal from another router from Apple, so if you want to take the AirPort Extreme on the floor and extend wireless signal, you will need another airport connected to your modem by Ethernet cable router to produce the wireless signal that will extend the extreme on the floor.

  Another way of saying the same thing would be to say that if you want to extend wireless using a router from Apple, you'll need two of them do... because AirPort Extreme is not compatible with a third-party modem or modem/router for this purpose.

• How can I get my HP 7310 to print completely wireless (w/out Ethernet cable)?

  I managed to install my HP 7310 printer to my router wireless using an Ethernet cable.  However, I'd rather have my printer HP 7310 connected to my network completely wireless, i.e. without the need for a long cable to my printer connected to the wireless router.  Is this possible?  If so, what can / should do to set up the printer this way?

  Hello

  Your printer doesn't have a wireless card so you must connect the cable to the router / access point. You can also add a wireless for your printer print server (cost over $$) like this:

  http://compnetworking.about.com/od/wireless/SS/wirelessgear_4.htm

  Kind regards.

  PS, the above print server is for example only, please do NOT buy it, it is a bit of waste.

• Satellite 1900 cannot conect directly to the modem via Ethernet cable

  I have a Satellite 1900 305 and I can't access internet when it connects directly to the modem cable via ethernet (RJ45), even after doing the procedure of recovery, and before I could. I can work normally and have internet if I connect to the pit of the modem a network hub. Can someone help me with this problem?

  Hello
  If I understand you correct you a trying to connect your laptop via Ethernet to a router or Modem or anything else, which is connected to the internet.

  Well it be, that the cable you a way to make this either a cable crossing of files?

  Good bye

• Unable to connect wireless Hp OfficeJet 3830 to my laptop

  The printer is connected to our broadband, but when I go on installing the software on my laptop with the CD that is given or online, he comes back with the error message saying "printer not found" I haven't tried manual connection via Ethernet cable still no luck. It is very fustratting that I have delays in the works! Someone knows how it can be connected? Or should I buy a USB cable in the shop? Be the easiest?

  Thank you very much!

  Welcome @Girkute,

  Thanks to their participation in Forums of HP! I see by your post that the printer is not recognized by the network. I will definitely do my best to help you.

  I believe that the steps outlined in this document should help solve the problem for the printer not detected: not found during Network Driver Setup printer.

  What operating system do you use? What operating system do you use?
   
  Feel free to click on the button 'Accept as Solution' and the 'Thumbs Up' for my help. Please let me know the results and if there is anything else I can help you. Thank you!

• Unable to connect wireless DNS server is not recognized.

  My laptop won't connect wireless does not have the DNS server has never had a problem before

  Hi Roger,

  Thanks for posting your query on the Microsoft Community.

  According to the description of the issue you are unable to connect wirelessly because there do not recognize the DNS server. The problem may be caused, if there is a miss match the IP address configuration. Then, I suggest you to try the steps below and see if it helps you to solve the problem.

  Method 1

  Automated convenience store is a tool that can find and automatically fix problems with your computer. These utilities are not designed to solve all the problems, but they are useful to try because they can often save your time and efforts.

  Run the network troubleshooter utility:

  Method 2

  If the problem persists, I suggest you to release and renew the IP address. For this you can see the steps below.

  1. Go to Start, click all programs and open the Accessories.

  2. Right-click on command prompt in the list programs, and then select run as administrator. If you are prompted for an administrator password or for confirmation, type your password, or click OK.

  3. In the command prompt, type the following command and press ENTER:
     enough ipconfig and press ENTER.

  4. Then type ipconfig / renew and press ENTER.

  5. Type Exit and press ENTER.

  Method 3

  If the problem persists, try to reset the TCP/IP stack and see if it helps you to solve the problem. To reset TCP/IP, you can refer to the procedure described in the article mentioned below. If fixit does not help, try to follow the manual steps.

  How to reset TCP/IP using the NetShell utility

  Hope it would help. If problem persists always post back with the current state of your computer and the result of the proposed suggestion, we will be happy to help you.

  Kind regards

• Unable to connect to the internet by cable sony bdp s490 network

  I have sony bdp s490 bluray player iam unable to connect to the internet by cable network

  my internet broadband requires the user name and password when using on the pc where should I apply the username and password when the internet connection for Blu - Ray player

  
  

• Only browsers and AVAST cannot connect to internet via ethernet. Computers on the same router via WiFi, MS update, ping cmd - all access

  Help! I'm about to commit the homicide of the computer!

  I have been troubleshooting for weeks and am now bald from ripping my hair!

  Computer: Dell Inspiron 537 s Slim Desktop  w / Pentium Dual - Core CPU E5200 @250 GHz

  Network card: Realtek PCIe FE Family Controller (checked several times, through Windows, it works correctly)

  System: Windows 7 Home Premium, 64-bit with Service Pack 1

  Router: Netgear N600 model #: WNDR3400v2

  Cable router: SBV5220 Surfboard Motorola

  Now several months ago this desktop computer once more had SOME programs lose the ability to access the internet via an Ethernet cable.

  Affected programs:

  MS Internet Explorer

  Mozilla Firefox

  Avast! Security Suite

  Work of MS Security Update

  Ping works sites (Yahoo, etc.)

  Other computers connected to this network via WiFi - no problem getting on the internet.

  Run the network troubleshooter advises all is working properly, no suggestion.

  Attempted fixes:

  Turn off all extensions on IE (but don't forget Firefox and Avast! are also unable to access.)

  Disabled all start-ups and the package process

  Restarted in Safe Mode - still not able to access.

  Ran check complete virus, then check virus run start. Minor ad-ware 'virus' not found, all corrected automatically.

  Rebooted the router and the computer to infinity and beyond! s

  Tried other computers using the same ethernet cable connected to this wireless routers cable, no problem accessing the internet.

  Disabled functions package

  Off MS Firewall

  IP Reset configuration (memory: netsh ip net reset c:\resetlog.txt - without DOUBT NOT EXACT - OF THE MEMORY.) Command worked)

  As I said, this had happened before and then miraculously fixed itself after a short period (less than 1 week). This time, no joy.

  Of course, it's one of two things:

  (1) a configuration problem I just can't find/understand.

  (2) the problem of equipment more strange, more selective, in the universe.

  Anyone? Anyone? Bueller?

  Thank you more can I possibly Express for assistance.

  You could win the lottery and have a lot of beautiful children!

  (M.) Kel

  Hello team zig - zag,

  I wanted to thank you for your help. I finally broke down and reached out to our friends at Microsoft directly for assistance. They had me a role through all the things that you suggested (again). And finally (after many hours of phone and chat discussions) came up with an answer: "* shrug * we don't know what is the problem - choose a restore point and come back to that.» What I did. This has solved the problem of internet access, but created other problems I'm trying (nothing that I have to post here, they are specific to a particular program package).

  Still, I wanted to thank you for your time and effort on my behalf. I'm very, very happy!

  All my best,

  Kel

• Office jet Pro 8610: how to connect Officejet Pro8610 via ethernet instead of wireless?

  Hello

  We recently bought Officejet Pro8610, but we can't use it yet.

  Our it team does not print wireless network.

  Thus, we tried to implement the officejet via ethernet with wireless turning-off.

  That's the problem.

  We have disabled Ethenet setting wireless and go-> advanced setting.

  We got a static IP for network printer and tried to manually enter the details and information, but nothing can be saved.

  We checked ehternet port is enabled.

  DHCP does not work either.

  Any suggestion?

  Thank you.

  Problem has been solved by replacing ethernet cable.

  It is curious that the faulty cable has worked with a laptop computer, but did not work with OfficeJet Pro.

  Therefore, conclusion to date.

  When the internet connection is having problems, there is a symptom that manual IP setting doesn't seem to work.

• Satellite Pro 6100: unable to connect to internet via wireless network

  Have had some problems with the audio device Yamaha for another thread, which now seems to be resolved. Thank you!

  However, do not know why, but now unable to connect to the internet via a wireless network, although the router works well as another computer in the House is connected wireless.

  When you check the available wireless networks it comes up with "no wireless networks were found in range, make sure that your computer's wireless switch is on.
  Where to check it, can anyone help?

  Thank you

  On the left side, there is WLAN switch. Make sure that the switch is in on IT. After doing this using FN + F8 key combination and activate WLAN device.

  After having done that, you should be able to see the WLAN networks available in your area.

• I could connect two laptops together via Ethernet cable

  Hello
  I'm playing a game via LAN but my router guard block that connect my comrades requests so I thought that we could create a network between two computers using an Ethernet cable and removing the router completely.
  Both of our laptops are manufactured by Toshiba and both the same type of model.
  Please tell me if this is possible and if it is what would be the best way to do it.
  Thank you, Jason

  You can, but need to run an ethernet cable crossover (null modem).  The MST it will not work without a router in the mix

• How can I connect a Time Capsule directly to my new MacBook Pro? I could connect my old MacBookPro directly via Ethernet cable, but there is no Ethernet port on the new MacBook Pro retina.

  I don't think I can connect wireless because I live in an apartment in a House and the modem and the router are in the main part of the House.

  If it was love at first sight... buy love at first sight for the ethernet card.

• How to connect a portable laptop Windows 8 with Windows 7 computer via Ethernet cable and transfer the data directly?

  I have a laptop Windows 8 . I want to connect to a new round of windows 7 and transfer the data at least 8 MB/s.

  Please send me the procedure to follow. I don't want to share Internet, but want to transfer data.

  You can do this, but you need a special type of Ethernet cable called a crossover cable.  This means the son in the swap position cables so that "send" and "receive" the computer two plugs can communicate.

  Learn more here: http://windows.microsoft.com/en-us/windows/connect-two-computers-crossover-cable#1TC=windows-7

• Unable to connect to internet via wireless router

  Original title: router Question through the network

  Hello!

  Basically, I use NET connection of type PP - Poe, that requires a user name & password to connect. I have 1 Mbps plan of development. recently, I bought a D-link wireless router.
  Connectivity is as---> main internet cable in this way will my internet port of the router. One cable goes on my desk from the LAN1 router lan port. I have configured my router with all the necessary parameters saved & now when I start my computer I dnt need to put the user name and password to connect to the internet.
  I is automatically connected to my network using the router I think.
  Now, the problem is that I use it more than 3 to 4 months. but now, when I start my pc, the network icon on the keep the taskbar on the search for the network all the time.
  Oh, I can't do something, or I can use my cursor also because I move my cursor, but cannot use it. Thus, in this condition I vigorously shutdown my pc, the turnoff to my router & then I start my pc. so if I want to connect to the network, I remove the mains cable and the plugin on my office lan and evrything port works fine. in this State I put the user name and password to connect to the internet.
  SO the thing is these days each time, I keep my router IT and start my pc to the Dungeon of the taskbar, the network icon on the turning points for an unlimited period.
  then, when I am facing this problem I keep my pc WE & the turnoff to my router, then after some time the icon bar of the tasks of the network stop (research or rotation) and it's yellow exclamation point. then use the internet I remove the cable main network from the router and connect to my office. He asks username and password then the connection works fine.
  I am using windows 7 ultimate 64-bit.
  still a very strange thing is when I'm dealing with this network icon turning question I connect my cell phone to my wi - fi router & it works well, but the scenario with my office is the icon itself keep turning. I use a basic wireless router. model No.:. DIR-524.
  I hope, I tried my best to explain my problem.
  waiting for the answer.

  Hello

  First of all, make sure that you have the latest drivers installed for the network card.

  I can suggest you to run the network troubleshooter and check.

  Using the troubleshooter from network in Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  Method 2:

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Method 3:

  Why can't I connect to the Internet?

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

  Hope this helps and keep us posted.

• Unable to connect wireless with Photosmart 2510

  I just upgraded my router from G to N.  I have a Linksys WRT10N.  My network is secured with WPA-Personal.  Since I upgraded from G to N and WEP to WPA, I'm unable to get my 2510 Photosmart to connect to the wireless network.  Initially, I was in WPA2 and downgraded my network to WPA with on security a bit of luck.  I entered all encriptación WPA data in the web browser integrated prior to installation.  I tried to install it several times and everything seems to go through OK but the blue light on the cover of never turns on again when the ethernet cable is disconnected.  When I run the network config. page it says "scanning" status of wireless.

  I talked to Linksys and they told me that the network N should work down to a B network printer.  Does anyone have any suggestions?

  Thank you!

  Hi Kim,

  All printers inkjet wireless HP since 2004 supports WPA - PSK and WPA2-PSK.  All new HP inkjet will certainly support WPA - PSK and WPA2-PSK.

  I'm more familiar with the WRT54G, but the WAPG works as well.  Here is how to convert the WRT54G in a simple access point:

  1. Connect LAN port of the WRT54G #1 and open the web without wire-router page (it should be 192.168.0.1 or 192.168.1.1)
  2. Go to the wireless section of basic wireless settings.  Create a new SSID and choose a channel without overlap, which differs from the WRT160N.  In North America, the overlapping channels are 1, 6, and 11.  Press to save the changes.
  3. Go to the wireless security section and the configuration up to WEP.  Press to save the changes.
  4. Return to the configuration page.  Disable the DHCP server and set the router IP address to something other than then the address IP of WRT160N.  For example, if the WRT160N IP address is 192.168.0.1, and then set the WRT54G to 192.168.0.201.  Make sure that the first three groups of numbers of the IP address are the same.  Press to save the changes.
  5. Now, connect an Ethernet cable between WRT54G #1 LAN port and one LAN of the WRT160N ports.