Unable to detect or to access the NAS

Similar Questions

• The NAS can be turned on without a disc?

  Recently, I took a drive on the NAS that I intend to sell it. Before removing the disc (which is now used in another device), I forgot to put back the NAS to its factory settings to remove my information and data of the NAS. I assumed that the NAS should have a form any internal memory only for the operating system to function. Is this the case? And if so, how to access the NAS? It has been sitting on a flashing power a LED all day and I tried to use the start menu to reset it without success.

  If the NAS does not work because it stores the BONES and it has information on the first hard disk, you then install what it means if I insert a new disc, it'll be like setting up from scratch again?

  Thank you

  TheDmac wrote:

  I forgot to put back the NAS to its factory settings to remove my information and data of the NAS.

  All what you need to do is wipe the drive. If the sale of discs with the NAS some would prefer to make a secure disk erase (you can do this if connect drives to your PC).

  A factory default will not work without disks. The purpose of this option of start menu must wipe disks (to wipe all your personal information, all data, settings, all on drives) and do a clean install of the operating system, to create a new volume, etc.

  TheDmac wrote:

  I assumed that the NAS should have a form any internal memory only for the operating system to function. Is this the case? And if so, how to access the NAS? It has been sitting on a flashing power a LED all day and I tried to use the start menu to reset it without success.

  The OS is installed from the flash on the disks. All of your personal information are on the disks. The operating system is installed on both drives so if a broken disk we can still see newspapers etc. on the other disk.

  If you look in RAIDar you won't see the error no disc detected.

  The flash containing the firmware image content, but also things like the serial number of the device. We do not store any of your personal information at all. The flash is 128 MB, I think. It contains space for the content of the image of the firmware (which are highly compressed) and allows a bit of growth in the size of the firmware image.

  We do not use the flash for the early stages of the start-up procedure, but we move quickly to boot from the disc.

  TheDmac wrote:

  If the NAS does not work because it stores the BONES and it has information on the first hard disk, you then install what it means if I insert a new disc, it'll be like setting up from scratch again?

  Yes, but with the firmware currently on the flash which is the newest firmware you updated. When you update the firmware, it is updated on the flash and installed on the disks.

  TheDmac wrote:

  Recently, I took a drive on the NAS that I intend to sell it.

  Please note that the warranty is to the original from only authorized retailer buyer. So those who don't buy it will have no warranty.

• New Win 7 computer cannot access the IP address of the network printer. Help, please.

  Greetings,

  -----------------------------------------------------------------------------------------------------------------------

  UPDATE: we have found the solution to this problem, we, and that I posted an explanation as well as two ways to solve the problem in my 2nd post on May 5, 2015. Scroll down to it for the solution. Unfortunately, Microsoft does not allow the OP to mark one of their own messages as 'the Answer' so this thread continues to be listed as "no answer" when he actually answered me.

  -----------------------------------------------------------------------------------------------------------------------

  The original message follows...

  We cannot sign a new Win 7 (64-bit) computer to a printer ethernet established in our local network of 'working '. We have reached the limit of our troubleshooting skills and expertise assistance.

  Our Local network
  ------------------------
  The printer is a Dell 5100cn workgroup laser that is connected via an ethernet cable to a 10/100 workgroup switch 5-port Cisco/Linksys. The switch is connected to the built-in cable Motorola modem / 4 port gigabit router / WiFi access point. There is no server between the printer and the network.

  Other computers on the network run also Win 7 and have no trouble seeing and using the printer. Some computers are connected via a gigabit ethernet cable to the router Motorola. Other computers connect wireless WiFi (once again, by the same Motorola device). All computers, including the new ones, are attributed to the same workgroup.

  The printer has a static IP address. It also has an integrated Web page accessible within the network via a browser to view the status of the printer. All previous computers can view the status of the printer Web page by entering its IP address in a browser.

  The new Win 7 computer
  --------------------------------
  At the Windows command prompt, we successfully ping the IP address of the printer and received a return signal. However, we are unable to connect to the IP address of the printer (and status Web page) with a browser. And we cannot find the printer when install us the printer driver. We have tried to turn off the Windows Firewall and it did not help.

  When we install the driver, move us as a 'local' printer and create a new "Standard TCP/IP Port" for her. We enter the static IP address of the printer and name the port. Define us the Protocol to "LPR", enter the name of the queue ("lp") and activate SNMP State with name of the 'public' community and the index "1". These settings have worked very well with our previous computers.

  When the time comes to 'choose printer', we select 'have disk... '. ' and use the Dell 64-bit for this printer driver. But it does not work and do not print a test page. We even tried to install the printer as a 'network' printer driver, but it does not, either. In addition, the 'local' method always seemed to work best in the past.

  The new computer has no harm to see other computers and devices on the network. For example, there is a NAS connected to the same switch Cisco/Linksys like the printer and the computer can access the NAS via its static IP address. The new computer can also access the internet. He can't use the IP address of the printer. We even tried to change the address IP of the printer, but that did not help either.

  Despite the fact that the work - the network troubleshooter Windows command prompt ping indicates that the printer is not responding. What do we lack? Help, please.

  Greetings,

  I hope that this will be our last post on this subject. We have discovered the source of the problem and can offer two 'fixed' in case someone else runs into the same situation.

  With the help of MSConfig and a process of elimination, we have disabled non-Microsoft services that were running on the computer until we discovered that "Qualcomm Atheros Killer Service V2" was the source of the problem.

  Explanation

  ----------------

  Our new Win 7 computer contains a communication module ethernet/WiFi/Bluetooth e2200 Qualcomm Atheros. The manufacturer provides a '' Killer Network Manager '' for this system. Its purpose is to monitor and control the flow of data over a network connection in order to optimize for. For example, the user can choose to give the program A high priority and program-B low priority. This ensures that the program-A is less lag in the network traffic.

  The primary market for this function, so far, has been the online game (where the name of 'Killer'). It allows players to channel the bulk of the bandwidth available to their game and away from other programs and services that are running at the same time. A response faster online gives the player the advantage it needs to get "kill him" before someone else.

  This system of control of bandwidth has interfered with data packets of return of our network, clearing communication between our computer and our printer printer.

  Difficulty 1

  --------------

  The simplest solution for us was to disable 'Qualcomm Atheros bandwidth control' for the ethernet NIC that has been accomplished by going to: Windows Control Panel > network and Internet > Network and Sharing Center > change the settings of the card (in the sidebar). Then we clicked on our connection to the LAN (our NETWORK ethernet card) and select the 'Properties' command Finally, on the Networking tab, we have disabled 'Qualcomm Atheros control bandwidth' and clicked 'OK' button to close.

  All that was needed after that was a quick restart and we were able to access our printer even with the killer Network Manager and functioning of Qualcomm Atheros Killer Service V2.

  Either way, we left the control function of bandwidth enabled for wireless (our) network connection because we do not plan on using this network printer when the computer is untethered to ethernet.

  Difficulty 2

  --------------

  If you don't want the killer running Network Manager on your computer, you may be tempted to uninstall. Do not! Uninstall will also uninstall the drivers needed for your ethernet, WiFi and possibly your Bluetooth as well. We heard that some users have communicated with Qualcomm and were able to coax, on their part, the necessary drivers comm without luggage "Killer". But you don't need to do it, either.

  All you need to do is: (1) remove the 'Killer Network Manager' of the '"start up" folder of the start menu of Windows (under "programs") and (2) using MSConfig, uncheck "Qualcomm Atheros Killer Service V2" under the ' Services ' section. Then reboot and you're good to go. The killer Network Manager and his service will not work.

  Moreover, the reason for which we did not chose this method, ourselves, is because we see one deserves that available Killer Network Manager so that we can block network traffic to select programs. Solution 1 converts this easy thing because the Ethernet bandwidth control can be quickly activated again if she is ever desired. And we're leaving it enabled for our WiFi.

  Best regards, David-EH

• I can't use windows Explorer or the network drive mapping to access my NAS drive more.

  original title: strange NAS problem

  Hi everyone I can't seem to fix this strange problem.

  I can't use windows Explorer or the network drive mapping to access my NAS drive more.
  I am running windows 7 Professional 32-bit on my PC, and until about a week ago she accessed from my PC very well.

  The location could not be reached and have not been able to run since said today that I went to update it and the drive mapped. I'm at my wits end.

  Here is some info.

  I can access to other computers and devices on my network.

  I can access the internet.
  I have a windows XP PC in the House who can always connect to my fine NAS drive (even if it's not mine).
  I PING the NAS drive.
  The NAS drive will do the same if connected via cable or by wireless.

  UPDATE: after the implementation of a shared folder on a Windows XP computer on the same network I am also unable to acsess the part of my PC. So I can assume that I can't browse all share folders or NAS drives on my local network.

  Help, please.

  Thanks for the help, but I fixed my problem

  Here's what I did in case anyone wants to know.

  I went into Device Manager and went to network adapters.
  I then expanded this section and under view changed to display hidden items.
  Several hundred elements appears (for most 6to4 adapters) and I deleted all the.
  Then click scan for new hardware.
  And... everything works again! YAY!

• remote VPN and vpn site to site vpn remote users unable to access the local network

  As per below config remote vpn and vpn site to site vpn remote users unable to access the local network please suggest me a required config

  The local 192.168.215.4 not able ping server IP this server connectivity remote vpn works fine but not able to ping to the local network vpn users.

  ASA Version 8.2 (2)
  !
  host name
  domain kunchevrolet
  activate r8xwsBuKsSP7kABz encrypted password
  r8xwsBuKsSP7kABz encrypted passwd
  names of
  !
  interface Ethernet0/0
  nameif outside
  security-level 0
  PPPoE client vpdn group dataone
  IP address pppoe
  !
  interface Ethernet0/1
  nameif inside
  security-level 50
  IP 192.168.215.2 255.255.255.0
  !
  interface Ethernet0/2
  nameif Internet
  security-level 0
  IP address dhcp setroute
  !
  interface Ethernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  Shutdown
  No nameif
  no level of security
  no ip address
  management only
  !
  passive FTP mode
  clock timezone IST 5 30
  DNS server-group DefaultDNS
  domain kunchevrolet
  permit same-security-traffic intra-interface
  object-group network GM-DC-VPN-Gateway
  object-group, net-LAN
  access extensive list ip 192.168.215.0 sptnl allow 255.255.255.0 192.168.2.0 255.255.255.0
  192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
  tunnel of splitting allowed access list standard 192.168.215.0 255.255.255.0
  pager lines 24
  Enable logging
  asdm of logging of information
  Outside 1500 MTU
  Within 1500 MTU
  MTU 1500 Internet
  IP local pool VPN_Users 192.168.2.1 - 192.168.2.250 mask 255.255.255.0
  ICMP unreachable rate-limit 1 burst-size 1
  enable ASDM history
  ARP timeout 14400
  NAT-control
  Global 1 interface (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0
  Route outside 0.0.0.0 0.0.0.0 59.90.214.1 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  the ssh LOCAL console AAA authentication
  AAA authentication LOCAL telnet console
  AAA authentication http LOCAL console
  AAA authentication enable LOCAL console
  LOCAL AAA authentication serial console
  Enable http server
  x.x.x.x 255.255.255.252 out http
  http 192.168.215.0 255.255.255.252 inside
  http 192.168.215.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  Crypto-map dynamic dynmap 65500 transform-set RIGHT
  card crypto 10 VPN ipsec-isakmp dynamic dynmap
  card crypto VPN outside interface
  card crypto 10 ASA-01 set peer 221.135.138.130
  card crypto 10 ASA - 01 the transform-set RIGHT value
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  crypto ISAKMP policy 65535
  preshared authentication
  the Encryption
  sha hash
  Group 2
  lifetime 28800
  Telnet 192.168.215.0 255.255.255.0 inside
  Telnet timeout 5
  SSH 0.0.0.0 0.0.0.0 outdoors
  SSH timeout 5
  Console timeout 0
  management-access inside
  VPDN group dataone request dialout pppoe
  VPDN group dataone localname bb4027654187_scdrid
  VPDN group dataone ppp authentication chap
  VPDN username bb4027654187_scdrid password * local store
  interface for identifying DHCP-client Internet customer
  dhcpd dns 218.248.255.141 218.248.245.1
  !
  dhcpd address 192.168.215.11 - 192.168.215.254 inside
  dhcpd allow inside
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  Des-sha1 encryption SSL
  WebVPN
  allow outside
  tunnel-group-list activate
  internal kun group policy
  kun group policy attributes
  VPN - connections 8
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  Split-tunnel-network-list value split tunnel
  kunchevrolet value by default-field
  test P4ttSyrm33SV8TYp encrypted password username
  username kunauto password bSHrKTGl8PUbvus / encrypted privilege 15
  username kunauto attributes
  Strategy Group-VPN-kun
  Protocol-tunnel-VPN IPSec
  tunnel-group vpngroup type remote access
  tunnel-group vpngroup General attributes
  address pool VPN_Users
  Group Policy - by default-kun
  tunnel-group vpngroup webvpn-attributes
  the vpngroup group alias activation
  vpngroup group tunnel ipsec-attributes
  pre-shared key *.
  type tunnel-group test remote access
  tunnel-group x.x.x.x type ipsec-l2l
  tunnel-group ipsec-attributes x.x.x.x
  pre-shared key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  Review the ip options
  inspect the netbios
  inspect the rsh
  inspect the rtsp
  inspect the skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect the tftp
  inspect the sip
  inspect xdmcp
  inspect the icmp
  !
  global service-policy global_policy
  context of prompt hostname
  call-home
  Profile of CiscoTAC-1
  no active account
  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
  email address of destination [email protected] / * /
  destination-mode http transport
  Subscribe to alert-group diagnosis
  Subscribe to alert-group environment
  Subscribe to alert-group monthly periodic inventory
  monthly periodicals to subscribe to alert-group configuration
  daily periodic subscribe to alert-group telemetry
  Cryptochecksum:0d2497e1280e41ab3875e77c6b184cf8
  : end
  kunauto #.

  Hello

  Looking at the configuration, there is an access list this nat exemption: -.

  192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0

  But it is not applied in the States of nat.

  Send the following command to the nat exemption to apply: -.

  NAT (inside) 0 access-list sheep

  Kind regards

  Dinesh Moudgil

  P.S. Please mark this message as 'Responded' If you find this information useful so that it brings goodness to other users of the community

• Unable to access the store using the proxy server.

  I'm in Windows 8. I'm unable to access the app Store. He said:-"we were not able to connect to the Store.This could not have come because of a problem with the server or the connection network has expired. Please, wait a few minutes and try again.and some other applications also. I use a 1.1 proxyserver (squid) that requires basic authentication.
  However I m able to use some of them as weather, maps, etc.

  I read solutions who suggested to temporary disable firewall and antivirus for test, I even try it but fails again.

  Other suggestions where has been going for windows 8.1 upgrade level, but how can I get this update, as it is downloaded in store that I can't access. Help, please.

  Hi Anand,

  Your computer is connected to a domain?

  Using a proxy server can allow the administrator to limit access to the Internet.

  You can reduce the effect of these problems by allowing unauthenticated through your proxy server access. We recommend that you enable unauthenticated access only for connections to URLs used by each application that has a problem. Some proxy servers may suggest that you create a list of URLs (also known as the 'white list') permissions.

  Please refer to the article to address these issues that relate to the use of Windows Store apps or use of Microsoft applications that are included with Windows Update or Windows 8, you can include the addresses mentioned in the article in a list of permissions ('white list') on your proxy server and enable HTTP and HTTPS access for them :

  The use of proxies authenticated with Windows 8

  For more information, see the article:

  Using the Proxy selection and Proxy bypass lists

  You can also consult the steps by Rajesh Govind, Support Engineer, may 4, 2013 and check.

  Windows 8 apps not able to detect the proxy for my machine settings.

  Hope the helps of information. Let us know if you need help with Windows related issues. We will be happy to help you.

• Unable to connect to the NAS network via a wired connection?

  Hi all

  I have 2 network NAS. They are both a Bay D-Link ShareCenter 2. One is full of media I use for streaming and the other is used to keep backups of my computers and some software. Both of the NAS are configured in RAID mirror. They both worked fine when I got them almost a year ago, they are mapped to letters pilot Y and Z. 2 days when I logged my office a popup notification came to say.
  "cannot reconnect to all network drives, click here to check the status of your network drives."
  so I checked it status and he said they were offline. I restarted my computer and both the NAS, but it made no difference. Then I tried to disconnect the drives, but when I try to reconnect to them I get this error;
  "Windows cannot access \\192.168.0.32\Volume_1\Joe, check the spelling of the name. Otherwise, there could be a problem with your network. In an attempt to identify and solve network problems, click on diagnose. »
  When I click to diagnose it is unable to find a default.
  The next thing I did was disable my Ethernet card and connect to my network with my WiFi adapter. Then I tried to re - map the NAS is connected via the wireless. This time he allowed me to map them and they seem to work as usual via the wireless connection, but it is rather slow on the wireless.
  Then I disconnected my WiFi connection and reactivated my Ethernet card. When I tried to open the NAS I get this error message;

  "An error occurred while reconnecting Z: to \\192.168.0.32\Volume_1\Joe, Microsoft Windows network: the local device name is already in use." This connection has not been restored. »

  A friend told me that this error was because the drive letter is used by a USB storage device or remembered from a previous session, and to remedy, I should run these 2 commands CMD;
  NET use * / Delete Yes
  NET use / persistent: no
  After you run the two orders, nothing has been changed still the same problem. I also I have no USB storage device so it may be that.
  The next thing I tried was to ping both the NAS, I did this on Ethernet and WiFi connections, and both times I return a normal response both to the NAS.
  I defrosted then to restore an image from my Office I made around a week ago and I know that I don't have this problem at the time. The image I did was with Acronis. When I started on the CD of Acronis support, I discovered that Acronis software could connect both the NAS on my desktop Ethernet. After restoring I still have the same problem.
  Now, there's 1 thing I noticed, my laptop can still connect to both WiFi and Ethernet NAS with all the problems. I also have an android phone, and who can connect both of the NAS via a WiFi connection.
  1 last thing you to know is I can always get to the configuration of the NAS so pages I visit it local address in a web browser. I also ran a factory reset both the NAS and then re-applied my own settings. This does not solve the problem, and more that turning March my routers.
  Please can someone help me solve this problem. I'm running a Windows 8 Pro 64 Bit operating system. If you need more information on my system spec or how I have my setup of home network please let me know.
  Thank you Joe.

  This problem has now been fixed.

  For some reason any my AVG firewall had defrosted on its own to block access to the features as well as to define its self to disable the file and printer sharing of files on the NAS share.
  So a small trick to my firewall and everything works as it should.
  Thank you Joe.

• Time machine is unable to perform a backup. Not able to access the sparsebundle. Problem occurred first on snow leopard OS. Followed Dragon upgrade to El Capitan. Only difference has error code of 109 changed to null. What about someone?

  Time machine is unable to perform a backup. Not able to access the sparsebundle. First of all, there is problem with the Snow Leopard operating system. Dragon followed in the upgrade to El Capitan. Only difference was error code 109 changed to 'null '. What about someone?

  We need some info.

  You can access from the finder Time Capsule? If this isn't the case, then Time Machine will not work.

  You upgrade the computer snow to El Capo and keep the same name?

  If you want to backup, it is best to start again... clean the new backup any attempt to add a previous backup failed.

  I recommend that you actually erase the TC... do a complete factory reset and start again.

  The previous backup if necessary can be archived on a USB drive connected to the TC assuming that Airport utility can still access it. Airport utility accesses the TC?

  With update installs all sorts of things can go wrong... so tell me more if you can not get anywhere.

• Firefox is unable to access the internet

  Hello

  Firefox is unable to access the Internet. Internet in the phone works, because all applications in my phone are able to access the Internet. I tried to access several different web pages. Their work. The screen is all black, no error messages appear. The strange thing is that Firefox Sync seems to be able to connect to the server, and I can download plugins.

  Best regards
  Joel Hedestig

  You can try using the beta version of firefox mobile?

  https://play.Google.com/store/apps/details?ID=org.Mozilla.firefox_beta

• Firefox update prevents access to the NAS web page

  Firefox is the likely cause of the web administration of a Buffalo Linkstation Live 1 TB network attached page being inaccessible storage device.

  This has happened

  Each time Firefox opened

  is every attempt to open the NAS web administration page after that Firefox updated to level to 3.6.6

  With some effort, this has been resolved. and it is the browser of the cause.

  Test with configuration as a result of security changes made no difference to the outcome of the error reported. It took uninstalling internet security suite to expose Firefox as being the cause. The default settings have been the "use system settings" option in the tools/options/advanced/network Panel. I never had the opportunity to change something in this space, because I started using Firefox, and when I installed the Sep 09 NAS, access via FF using the ip_address was the norm.

  However, when you attempt to connect using FF to the security suite 'not there' a proxy not responding error occurred, which was the point on the cause. The FF network Commission review, a manual selection of the proxy server and if no proxy for local connections was the required patch. He continued to work after security suite has been reinstalled. A jpg of this working configuration image is attached.

  In the last 6 months FF suffered a number of updates. One of those - most likely 3.6.4 or 3.6.6 - changed something in FF mode of local network connection management. In which case the same ip addresses in the address bar previously authorized were no longer allowed - all without talking to the user in the update until the condition occurred in operations.

  This is the second time a mozilla product did that for me, on the automatic update, and I'm upset that a good product may be contaminated by defects of design and testing in this way. Updates automatic for FF and TBird are off my calendar. If the effects of the end of a change are not complete and explained in detail - I don't use it. the pain of the errors that it is caused is considerable.

  Davidk

• Since the installation of the last update of iOS on my iPad I'm unable to type in the address bar of safari. I can access the Web sites of my favorites, but when I try to enter a new address safari closes its doors.

  Since the installation of the latest update on my iPad, I'm unable to type a new address in the address bar of Safari. I can access the Web sites of my favorites, but when I press the address bar Safari closes its doors.

  I reset holding home and power button at the same time. I did that 4 times. I also left all the settings.

  I am also unable to access the server from imessage. I don't know if these two things are related, but the two that happened after the update to iOS 9.2.1

  Since this announcement, I found a Reddit thread that suggests a temporary solution by disabling Safari suggestions. It worked for me.

• How access root of the nas

  Hello.

  Anyone who knows how it is possible to access the root of the SIN? I'm running Kubuntu and tried to mount it with:

  sudo mount-t nfs nas_mc: / / / mnt/nas

  Apparently it only works when a share is mounted. Or have I missed something. Is there another way to do it? I just need to be able to look at the root of the nas...

  Kind regards

  Casper

  It is not exported with NFS; you need enable ssh in the systems-> settings-> services and connect that way.

• Stupid MS is unable to detect the operating system of W2KPSP4 but sees IE6SP1 user agent

  It is ridiculous that Microsoft (coding of Web Pages webmaster) is unable to detect that a user entering the page has a (drop dead) of Windows 2000 Professional SP4 operating system (OS)...

  and then always recommend (MS) install IE 8... When as far as I know... an IE8 installation cannot complete successfully on the OS W2KPSP4?

  Hello

  The Microsoft Answers community focuses on the context of use. Please reach out to the business community of COMPUTING in the TechNet forum below:

  http://social.technet.Microsoft.com/forums/en-us/categories

• Activating game FSX error "Unable to Activate Online, a technical problem occurred while accessing the server"

  Original title: FSX Activation game

  Gentlemen: after years of use in FSX (Microsoft Flight Simulator X).  Now, I ran into a problem of Activation. His version of "Unable to Activate Online, a technical problem occurred while accessing the server, license authorization was not successful, we apologize for any inconvenience"...  Support for the game ended last year. Is this in any way about this? Or is it temporary problem? "My first post" thank you... P.S. When MS comes out with a new Flight Simulator thanks...

  Gentlemen: Problem 'Resolved' I went in FSX.exe properties and on the Compatibility tab, Switched setting the compatibility to Win XP SP3 for Windows 7. And it worked the active game. Thank you

  for the info and try to help. Simple, I hope someone else can learn from this. Thank you!

• MY mail server hardisk full so cannot start services & also unable to access the mail server

  I have the server messaging, but Hardisk ful then failed to start Services and also unable to access the e-mail mail server troubleshooting steps.

  Hello

  The question you have posted is related to professional level support. Please visit the below mentioned link to find a community that will support what ask you:

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer