Uninstall fail Photosmart 7510

Similar Questions

• Can multiple Photosmarts (7510 and C309g) be configured to scan on the same computer?

  I have an Acer PC Windows 7 with an AMD Athlon X II processor, 4 GB of RAM.

  I have Photosmart C309g and everything-each 7510, both connected via wi - fi, using different IP addresses that are not in conflict with other devices on my network.

  I executed the complete installation for both HPs.

  I can print either, but I can scan only using the 7510.

  When I open the HP scan diagnostic, it does recognize that the 7510 - the c309g is not yet listed.

  I noticed only 7510 application record contains a HP scan application and it also recognizes that the 7510.

  There is no application scan c309g folder.  I tried Win 7 Windows Fax and Scan application but that also recognizes as the 7510.

  1. is there a way to configure the system so that it can print and scan from these two Photosmarts?

  2. If the scanning using a 7510 and c309g does not work, could I use a 7510 both a 7520?

  Hello Osiris43,

  Welcome to the HP forums! I understand that you are unable to scan a document using the Photosmart Premium C309.

  You should have two printers scanning capabilities, because they have a different software. The Photosmart printer using the Solution Center and the Photosmart 7510 uses the Printer Wizard.

  I suggest you uninstall/reinstall the software Photosmart Premium C309. Please follow these steps:

  Please follow this HP document uninstalling the software of the printer.

  Then, perform a clean boot on your computer. I'll give you a Microsoft document on this step here.

  Now, install the full features on the site of HP software here. Choose your operating system that is appropriate; 32-bit or 64-bit.

  Once installation is complete, please click on the document to Microsoft, and "how to reset the computer to start normally after a clean boot."

  Please send me your troubleshooting steps.

• Photosmart 7510: Need an installation software

  I had to uninstall my printer to my laptop.  I guess I'd be able to re - install with a download from the Web site, but I am unable to find anything.  The original CD supplied with my printer is now incompatible with my operating system.  Where can I find software to re - install my printer on my computer?  Thank you.

  Hi there @rcohenkim ,

  Welcome to the forums

  I have seen your post about how you want to install your Photosmart 7510 on your Mac of Yosemite and do not have the disc. It's quite normal, that you can click on the link I posted below to help the pilot will need to 10.10.

  Series 7510 C311 Photosmart HP full feature software and drivers

  I hope that helps you with the driver you are looking for

• Photosmart 7510 C311a: Bought used Photosmart 7510 C311a and does not allow me to print

  Good afternoon everyone,

  New to the Forum and took a look around to see if my problem could be fixed, however, I was not able to locate a suitable to my printer. I recently bought a printer Photosmart 7510 of second hand without a usb connection or installation of the cd. I managed to hook the printer up to my wireless network and test prints however, when I try to print something in the computer itself, the printer will not be displayed to draw. I pulled up the devices on my home screen, and it allows me to choose this printer as my favorite. I try to run the troubleshooting option and he answers, "the WSD print device driver is not installed. Install the latest driver for the device. I click on the option 'Apply this correction' and she comes back with him could not be installed because there was no driver found. I tried to download the right driver, but it is yet to be found on my computer. Any help would be greatly appreciated!

  Respectfully

  ~ MightyCaz

  Hey @MightyCaz,

  Welcome to the Forums of HP Support!
  
  I understand that your connected HP Photosmart 7510 wireless e-all-in-one printer fails to print from your Windows 7 computer. I would like to help you today with this printing problem. Because you get the message that "WSD print device driver is not installed... " It would seem that the packet driver HP full feature software is not installed. So, I'll you run through some standard troubleshooting steps below to fully install your HP Photosmart.

  Can I have it please click here to download the package full feature software and driver of your HP Photosmart camera. Once the download is complete, please follow the instructions on the screen to install your all-in-one. Once installation is complete, please try printing and scanning to confirm that everything works as normal.

  Please reply to this message with the result of your installation. I look forward to hear from you!

• HP photosmart 7510-e & mac does not connect to print;

  Recently successfully installed HP photosmart 7510-e all in one printer on wireless home safe and functional very well. Today press & won't print. Printed from the other laptop, but not mine. performed tests & said my Macbook pro says unknown device wireless. Do I need to uninstall and reinstall or another problem? Thank you.

  Thanks for the quick reply PrintDoc.

  I tried what you suggested, nothing works.  However, I noticed when scrolling down to the network default reset is there a way to manually assign an IP address.

  It took a lot of play, but ultimately, what worked was.

  1. Reset default network settings
  2. Manually set the IP address and the address of the DHCP server (DHCP address was wrong)
  3. Reserve the IP address of the router (so it's not assign this address to another device)
  4. Run the Wireless Setup Wizard

  I'm running now.

  Thank you!

• Print two-sided Photosmart 7510

  I'm running Mac OSX 10.9.3 and a pilot recently re-installed for my Photosmart 7510 (long story on renewed OSX installation). Any application that I use, I am unable to get the 7510 to start to print at the long edge binding. It ONLY prints in short-edge binding. I have re-installed the driver 2 X and downloaded 2 X so it should be no problem in this regard. Someone has an idea?

  Hi dominik_12,

  Welcome to the Forums of HP Support! I understand that you are not able to select Long Edge binding when you try to print to your HP Photosmart 7510. You have tried to uninstall and reinstall the driver unsuccessfully on the BONES of the Mavericks. I want to make sure we select the HP driver and not the AirPrint driver who would give only limited options.

  Complete the following steps:

  Reset the printing system

  1. click on the Apple icon and then click on System Preferences.

  2. in the hardware section, click Print & Telec. Dialog print & fax opens.

  3. make a right click (or Ctrl + click) in the left panel, and then click Reset printing system...

  4. click OK to confirm the reset.

  5 type the name and the correct password.

  6. click OK to reset the printing system. The dialog box Print & Fax shows no printer selected.

  Add the PS 7510:

  1. click on the sign plus (+) sign and locate the PS 7510, highlight the printer

  2 in the section using printing, make sure that you select the driver HP PS 7510 and not one AirPrint.

  See the image below (you want to click the HP not the AirPrint driver):

  

  Now that we have the PS 7510 driver selected, please open the program or document you are interested in printing and follow the steps here:

  1. click on the command Apple + P , your print dialogue box opens, click on the option view details at the bottom left (it may already be open)

  2 just below the Orientation section, click on the arrows to access the drop-down list, and then select page layout

  3. now you should see the two-sided printing of the menu drop down, here you can select Long Edge binding.

  4. click on print

  Now able to print successfully long edge bind you? Please let me know if this was helpful, I'll watch for your reply.

  Thank you

• Photosmart 7510 stop scan to PC (Windows7). Diagnostics and help have not solved.

  Printer - Photosmart 7510.

  System: I'm on Windows 7 home premium 64-bit, I have Norton 360.  Laptop is Acer Aspire.

  Problem - Photosmart 7510 - scan is no longer to the PC.

  Software won't uninstall (so I can ' t reinstall)

  Connect the printer software installation impossible (he always recognizes the printer on the network)

  Scanner not recognized.  When I click on scan HP he says 7510 series unrecognized.  If I click on manage scans devices/printers, nothing happens apart from hourglass.

  I lived all the online help and scan doctor and spent 3 days on this.  Nothing seems to fix it or repair.

  The scanner, printer and copier what worked first implemented, including scanning to pc.

  Now, everything works apart from scanning to PC.

  A few days later the scanner to the computer stopped working and could not be recognized if clicked (for example to allow the scan to PC function).  Scanner the doctor then tried to uninstall and reinstall the software.  The basic device HP software won't uninstall, whether through the HP program or control panel.  There after the reboot, even when supposedly uninstalled.  I tried to reset the defaults on the printer, turn off the power sector, removing the printer from devices and printers, fixing and cleaning the registry errors, checking all relevant WIA and CPP are restarted and automatic according to the directives of this help: http://h30434.www3.hp.com/t5/Scanning-Faxing-and-Copying/Photosmart-7510-won-t-scan/m-p/1749193/high... I followed all the HP help topics and have tried drivers updated and installation of HP.com.  My laptop was rebooted about 50 times in the last three days trying to get this resolved.

  When I click on the printer defined upward and the software it prompts you to connect the new printer.  It finds my 7510 (wireless), but says that it cannot install it.

  I can't do windows system restore, because there is no set of restore points.  I tried to disable firewall for connections and installation of the software.

  Various error messages appear:

  During the uninstallation using the control panel.

  "Scan to PC Activation App" needs closing (I can only find in the tasks of process manager I then complete the process)

  If I try to use the HP uninstall later said there is no uninstall HP.

  I have the original CD.

  Any ideas as to how my scan to PC to work again?

  Maybe this isn't the case in your situation, however, security software (firewall/anti-anti-virus/malware) can cause endless problems, depending on their configuration. Norton 360 is an extremely invasive program, part of what makes it so effective. But, get the settings to allow access install/uninstall the devices through 360 can be complicated. My advice before you try anything else, would be to disable Norton 360 (gives you regular intervals) then try Solution 3 in the Windows 7 of this troubleshooting document installation section:

  http://goo.GL/Qtbcf

• HP Photosmart 7510 copy two-sided documents

  My newly installed HP photosmart 7510 (model No. C311a) will not copy two-sided documents.

  Here's the story: on the screen of the printer, I went to copy > Settings and choose "2 faces".  After the first printing, side I put the original and replaced it in the charger.  After a break for the ink drying, the screen read "Copy...", but the original was not sucked into the feeder and the copy that came out had only the first side top.   I repeated several times with the same result.

  At no time did any alerts or error messages.

  I tried all the remedies suggested earlier:

  http://h30434.www3.HP.com/T5/printing-issues-troubleshooting/HP-Photosmart-7510-won-t-print-double-s...

  I uninstalled all the drivers, etc of the CD included and downloaded and installed later from HP.  But no help!

  I went to: Control Panel > printers & faxes > series of HP Photosmart 7510. Right-click on the last, I have found no reference to "Restore preferences", "Reset Printing System", or "installation of printer," as mentioned in the previous post.

  On the homescreen of my computer, I clicked on the icon "Series of HP Photosmart 7510."  Assistant HP printer that has opened, I chose: the value of the preferences > series HP Photosmart 7510 printing preferences > advanced. At the last, I have reset print borderless to 'Print without borders', but it was also without success.

  I have Windows XP Pro. Any other suggestions?

  Hello

  AMPe #21 its manual implies that we should use the glass, NOT the ADF. I've tested this and it worked.

  I hope this helps.

• Cannot connect Photosmart 7510 computer wireless

  I have a Photosmart 7510 with results as follows: connectivity - related - not run settings, - No - FAIL filtering.

  Help, please.

  Set a static IP address on the printer out of range of the router DHCP.   Now try to connect.  If not, disable the security on the router again and try to connect without security.  If successful, go back and add WPA2-AES (pers.) with a simple password to test.  You can connect now?

• HP Photosmart 7510 won't use photo black ink

  I have a photosmart 7510 printer and I am printing from microsoft word 2010 on a windows 8. I print a word with no pictures in document. Printer preferences are on plain paper with normal quality. I can't the printer to use the XL Black ink cartridge. It only uses photo black ink. Is there a setting that I can choose to let him use the regular black ink?

  Hi shirsar,

  I understand that you have a Photosmart 7510 which seems to use a lot more than regular black ink black photo. I'm sorry to hear that, but think I can help you with a solution.

  You can set the printer to use only black ink when printing from the PC and ensures that it uses black ink and no ink picture. My instructions will be set up in the pilot if he does for all programs (if you just want to program it please let me know, and I advise you more). You'll want to start by going to your start screen, and simply start typing devices and printers, and you want to open that (if that is not in the work Panel type and then proceed to open devices and printers). Once the devices and printers is open, right-click on your Photosmart 7510 icon and select Printing Preferences. You'll want to then click on the Advanced Options button at the bottom right of the screen. The next page that appears will allow you to set the printer to use black ink only when printing from the PC (please follow the screenshot below for any clarification).

  

  Hope this helps, have a nice day!

• Photosmart 7510: Errors of inconsistency of paper photosmart printer 7510

  I am trying to print my 7510 by using custom paper sizes and get paper mismatch errors.  I use Word for Mac v. 14.4.8 on a Mac under OS X 10.10.2.  I went through all the tips in the HP support pages to try to fix this problem without success.  There is no firmware upgrades or updates of available driver I can find support/HP.  This error is more annoying.  I have not had this problem on my old printers I've foolishly got rid of upgrade to the all-in-one printer. Can you give me any help other than suggests to use the information on the support pages that did not work.  ! have created various paper formats customized in word to see if I could find a magical Assembly which will print and have had no success.  If someone cannot help me solve this problem, it will be the last HP printer that I buy.

  Full of hope for some real help.

  Hey @oldgt!

  Thanks for getting back to me!

  If you see only the media and the quality in the dialog box print, then that indicates that you are using the Apple Airprint drivers and not the pilot series Photosmart 7510.  If the printer does not have the correct drivers, it may not work properly from third-party programs such as Microsoft Word or Adobe Reader.

  To remove and re-add the printer using its drivers:

  1. Click on the apple icon in the upper left corner of the Mac
  2. Click on System Preferences
  3. Click on printers and Scanners
  4. Select the printer and press the minus (-) signs below the list of printers
  5. After removing the printer, click the plus (+) sign below the list of printers
  6. Click "add another printer or a Scanner.
  7. In the add a printer window, select your printer
  8. In the drop-down list 'USE' make sure you only select the series Photosmart 7510 and NOT Airprint
  9. Add the printer and try to print again

  

  

  If please, after back and let me know if this worked for you!

• "HP Photosmart all in one single 7510: print greeting cards 5.5x10" on hp photosmart 7510

  "Unable to understand the print size of greeting card size full page stock measure 5.5x10.

  Hi @artdahlink,

  Thank you for joining the Forums of HP Support!

  I noticed that you are unable to print a 5.5 x 10 greeting cards on your HP Photosmart 7510 e-all-in-one printer. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I understand the frustration you feel. Please see the Specifications of printer for HP Photosmart 7510 e-all-in-one printer series.

  Maps:
  Card type / size chart

  • 3 x 5 Index / 76.2 x 127 mm (3 x 5 in)
  • 4 x 6 inch Index / 101.6 x 152 mm (4 x 6)
  • 5 x 8 Index / 127 x 203.2 mm (5 x 8 in)

  NOTE: According to the specifications, this printer does not accept a 5.5 x 10 (cards).

  There is no guarantee the implementation of a custom paper size to work, however, you can try this method

  • HP printers - creation of custom paper sizes

  Please reply to this message with the result of your troubleshooting. I can't wait to hear strings attached good luck!

• When I scan documents with HP Photosmart 7510 ADF, how can I stop the pages to be marked?

  Hello

  I use a HP Photosmart 7510 (model No. C311a, product no. CQ877B)

  When I scan documents using the automatic document feeder, they are more often (80%) marked left.  It seems to be caused by the wheel which initially grabs the book.  It provokes a black spot of the width of the wheel to be left on the page.

  The mark appears about a quarter turn to the bottom of the page and is about 1/2 cm in height, but is very sensitive.  Sometimes, another brand is left a little further down the page and sometimes these two brands are accompanied by a very reduced, but still noticeable grey banner (again I believe caused by the wheel).

  The brand is very visible not only on the scanned now but also (of course) in the pdf file that result, and since I'm on this printer for things like job applications, it's not big.

  Other people know about this?  If Yes, is it possible to fix it or must return the defective printer?

  See you soon,.

  silverShnoop

  Hello silverShnoop

  Such problems can sometimes be caused by dirty rollers or the parts of the ADF (automatic document feeder). The following instructions (whereas for a different problem) contain instructions for the cleaning of the AAD.

  The ADF (ADF) captures no paper

  There is another article that could help as well. It contains instructions for cleaning the scanner glass.

  Vertical stripes, lines or streaks in the Copies or Scans

• Photosmart 7510 - black ink cartridge does not print

  Recently, I replaced the ink cartridges on my Photosmart 7510 C311A. These are all the "genuine HP cartridges ', full.

  Black ink (with the symbol of the Pentagon) does not print, not at all. I ran through the standard troubleshooting steps:

  Cleaning of printheads

  Cleaning of copper contacts

  * Check for a good evacuation

  My colleague in the corridor as the printer even so I borrowed his black ink cartridge and tried: same problem. The printer does not record that there is a problem, but when I run printing tests, where there should be a black ink, there is absolutely none. All other colors print correctly.

  The printer doesn't lack NOT of the printer "align" test however does not offer a suggestion of what to do from there. I've not seen - in test reports - an indiciation of the misalignment.
  
  Suggestions on what to do now?

  I had the same problem. I had replaced the empty cartridge black and suddenly, no ink. Finally, what has worked is
  (1) I removed all the cartridges and cleaned the copper connectors with wet Publix.
  (2) I got a wet paper towel and he pressed repeatedly on the silver circular vent that would be under the black cartridge. I did until no black came. Let it dry.
  (3) I replaced all the cartridges and on the printer. I went to tools/clean the cartridge. I did it a couple of times and he finally printed black ink! I confirmed by going to tools/align, and align the cartridges successfully. He had kept before crashes when the black ink did not work.

• Photosmart HP 7510: HP Photosmart 7510 all in compatibility with 5.4 ghz?

  I recently changed my wireless router to work on the 5.4 ghz band and my HP Photosmart 7510 suddenly stopped working.  Turned back on and it works fine.  I guess the 7510 can't 5.4 ghz?  Can someone please confirm?

  If not is there a way to upgrade?   If no upgrade then what new HP All in one wireless printer is compatible with the 5.4 ghz band?

  Thank you!

  I don't know of a wireless printer that supports the 5 GHz band.  As the series limited to roughly half that of the 2.4 Ghz band, manufacturers are reluctant to put it in the printer.   They will always have to say "not move the printer closer to your router.