Upgrade of RAM works only on Intel S12

Similar Questions

• My R1 - 131 T N3050 configured with Windows 10 again is slow. A simple upgrade of RAM works?

  Also, I read the posts on the conversion of the SDD HARD disk, but it is unclear if this is possible with this model. Should I take it back to the shop of PCWorld and ask for my money back?

  R3 - 131T? Is not very difficult. I sent you a PM.

• Re: Satellite Pro L300D - 11O 800 MHz RAM installed, only to 667 MHz

  I recently bought a Satellite Pro L300D-11O, which has a single stick of 1 GB 800 MHz RAM installed. However this RAM work only at 667 MHz. I checked this in Linux and Windows Vista.

  The laptop is announced as to have 800 MHz RAM on this page:

  http://UK.computers.Toshiba-Europe.com/innovation/JSP/SUPPORTSECTION/discontinuedProductPage.do?service=UK&BV_UseBVCook ie = Yes & PRODUCT_ID = 1055796

  The manual of the user who wrote:

  "PC2-6400 memory module works as PC2-5300 speed the GL40 Express Chipset Express chipset/GL965"

  I don't know what chipset I have, and it would be surprised that this would be the case that the above Web site explicitly states RAM 800 MHz.

  Can someone tell me please?

  Hello!

  Now I'm a bit confused of Mr. I think you did search in the wrong user's manual because the Satellite L300D has no Intel chipset.
  On the Toshiba site, you can download the manual for Satellite L300D:
  http://EU.computers.Toshiba-Europe.com-online downloads support & -online download user manual

  I think that your chipset only supports 667 MHz. normally the RAM always works on the highest speed that is supported by the chipset.
  Check the specifications with Everest or PC Wizard 2008.

  Good bye

• My ram upgrade will not work

  I have a

  Tip: Hewlett-Packard 097Ch

  The bus clock: 800 MHz
  BIOS: Hewlett-Packard 786 1 v01.05 16/06/2004

  3.00 gigahertz Intel Pentium 4
  cache of 16 kilobytes main memory
  1024 kilobyte secondary memory cache
  Hyper-threaded (2 total)
  running on Windows XP Professional Service Pack 3 (build) 2600
  We went on our monitored computer crucial.com and we found that we could upgrade our RAM from 1 GB to 4 GB
  Memory: DDR PC2700, DDR PC3200

  Type of memory: DDR PC2700, PC3200 DDR, DDR (non - ECC)
  Maximum memory: 4 GB
  Currently installed memory: 1 GB
  Total of the memory locations: 4
  Available memory Slots: 0

  I bought the RAM compatible and installed, but I can not start the computer.  I get some kind of splash screen and the numbers in the upper right away at about 500 MB something tick and then stop, then nothing.  I put in our old ram - only 1 GB of total and the computer works fine.  I read in another form that I need to change the/MAXMEM in the boot.ini to 4096 but I can't because it resorts to default as soon as I press ok.
  Because we have spent some money for this RAM I am resistant to him give up and return to 1 GB of RAM.
  Please get back to me quickly because I don't want to have to go out this computer to someone to fix it for a lot of dollars when he could and probably is very simple

  The switch/MAXMEM, it's NOT what you want.  This has nothing to do with your problem.

  It is much easier to find the specs for the OEMs from companies like HP if you give the computer model rather than a code name of obscure motherboard.  Assuming that your motherboard can really take 4 GB (and the Crucial scanner is usually fairly accurate), it seems that if one or more of the new RAM sticks are bad or are not properly seated.

  Assuming that your old RAM was 4 x 512 MB (info was useful, too), you know that all 4 taken work.  Just try one of the new installation RAM sticks and start the computer.  Tell him separately with each stick.  Which should allow you to determine which, if any, of the new RAM is good.  Most of the RAM comes with some kind of warranty, unless you bought the cheapest possible source.

• Recently, I upgraded my RAM to 1 G. Since 2002 the picture it will work, but immediately stop saying that it will inform me if there is a solution to the problem.

  Original title: Picture It Photo 2002

  Recently, I upgraded my RAM to 1 G.  Since 2002 the picture it will work, but immediately stop saying that it will inform me if there is a solution to the problem.  Everything I read on this site, I think that the fix may be a patch.  Question: anyone know how to get me to the patch?

  Would appreciate it a lot!  Thank you

  This could it be? If not, Google more.
  http://forums.CNET.com/7723-6136_102-301075/Microsoft-Picture-It-2002-crash-patch-for-XP-only/

• Reading problem, when I playback my video it only plays for 2 seconds and stops, I upgraded my ram from 4 GB to 8 GB

  When I playback my video it only plays for 2 seconds and stops, I upgraded my ram from 4 GB to 8 GB, im using adobe production premium cs6

  Here is my card in my machine.

  Model name: Mac Pro

  Model identifier: MacPro1, 1

  Name of the processor: Dual-Core Intel Xeon

  Processor speed: of 2.66 GHz

  Number of processors: 2

  Total number of Cores: 4

  L2 cache (per CPU): 4 MB

  Memory: 8 GB

  Bus speed: 1.33 GHz

  It is found on all projects, I'm still under snow leopard, I have a NVIDIA GeForce 7300 GT graphics card, and yes the playhead stops after a second reading of a video in the source and program window.

  After hours of research and troubleshooting, I managed to solve the problem by signing on the standard user and account logging in as an administrator. Somewhere in the standard user account prevents play video.

  I'll recreate a different standard user account and see if that fixes the problem.

  Thanks for your response

• HP G62 slot work only 1 RAM

  I have a HP G62 laptop with two cards of 2 GB of RAM, but only one of the slots of RAM will work.  If I swap the cards up and down, they both work in the slot in the bottom, but none of them will not work in the upper housing.  Only the location of the bottom works.

  I recently ordered the BIOS to the latest version.  I had the laptop completely out several times replace the paste heat on the CPU and GPU, and another slot RAM problem, it seems to work very well.

  What can you do to a computer that recognizes that RAM in one of its slots?  Should I install an older BIOS?  Or probably it's a physical problem with the slot or the motherboard?

  Hello:

  IMO, there is a motherboard problem and communication with this memory is bad.

  The only solution would be to replace the motherboard.

• Upgrade of RAM for S12 with VIA NANO

  I just bought a S12 with VIA NANO processor (using right now).   I want to upgrade the RAM on it, but have a few questions.

  1. the amount of RAM this processor can handle?  It is specific to the operating system (Vista vs XP vs Win 7)?

  2. what type of RAM is the requirement VIA.

  Hi, if you update the new BIOS for S12 Via machine

  S12 VIA BIOS 23

  Summary of changes 20CN23WW: supports 3G of RAM.

  You can Upgrade to max 3 GB...

  Thus, every good brand S0 - Dimm DDR2 667 or 800 MHz 2 GB Memory Stick could do the job...

  Corsair, kingston, samsung, hynix, I wish...

  cordially KalvinKlein

• After the upgrade of RAM Equium A100-338 runs on battery only 30 min

  I've had my laptop Toshiba Satellite A100-338 for over 2 years now and the other day that I upgraded the RAM to 4 GB to 1 GB, I noticed that the battery level is low and I can't get to the 30-40 minutes out of the battery max. There generally has 1 hour 30 minutes to 2 hours of life on a battery fully so far

  I thought that adding RAM more would make the battery last longer, but I don't know she s RAM that of done

  Any help appreciated, thanks!

  In my opinion RAM upgrade cannot be responsible for the lower battery capacity. I've updated / downgraded memory on my notebooks and I didn t notice something like that.

  That means when you reuse the 1 GB of RAM you can use the battery run for too long?

• G42 - 490 YOU: what changes can I see or wait until after the upgrade of RAM?

  Hello

  My PC model # is G42-490TU, processor - Intel Core (TM) i3 CPU M370,
  RAM: 6.00 GB (2.93 usable), System Type: 32-bit operating system.

  I've recently upgraded RAM 2.00 GB to 6,00 GB with 2.93 GB usable, that's what it shows.

  I want to know if this 2.93 GB of 6,00 GB usable the correct value of the memory that is made available?

  Also, I want to know what changes can I see or wait after upgrading the RAM from 2.00 to 6.00 GB where 2.93 GB is usable? How does this improve the effectiveness of my PC? Is there something that needs to be done on my own apart from adding the RAM to increase performance and the maintenance of my PC?

  Thank you best regards &,.

  Isha

  The problem is the operating system of your laptop is 32-bit.

  A 32-bit operating system can use @ 3.25 GB installed memory.

  Install additional 4 GB to a laptop that had 2 GB was a regrettable mistake.

  As long as the 4 GB memory module you have is compatible, you'd better remove the 2 GB module and put the 4 GB module in its place.

  You won't find a lot of improvement with the current configuration of a 2 GB module and a 4 GB module. With this memory configuration does not work in dual channel mode.  You would be better with two modules of 4 GB, but this is only if you upgrade your operating system to a 64-bit version.

  In fact, you would have improved if your OS is 64-bit. A 64-bit Windows operating system will recognize and use the installed memory.

  If you really want to improve the performance of the laptop, you should consider upgrading to a SATA SSD 256 GB drive at least.

• 1221tx dv5: Upgrade of RAM 1221tx dv5

  I bought this laptop 32 bit in the year 2009 and set to level to Windows 7, so far, works well but facing a matter little in performance.

  Now I want to upgrade the RAM and do not know what RAM capacity will be the best run win 7 10 whereas my current processor (Intel Core 2 Duo Processor T6400).

  (1) will I go ahead upgrade with DDR2 4 GB additional RAM RAM totaling 8 GB? Or add additional 2 GB only?

  (2) install 64 - bit Windows 7 to 8 GB of RAM support?

  (3) it will give better performance to run Windows 7 or Win 10 on 32-bit?

  (4) pin 200 or 240 pin RAM?

  (5) any specific brand should I choose for compatibility?

  Thanks in advance!

  Best regards

  Raj Gupta

  If you already have a single module 4 Go DDR2-800, I guess I would buy another. I would not add a 2 gig module, because who does not run in dual mode. Also the difference between 4 and 6 shows single channel won't get noticed.

  32-bit to 64-bit will require a clean install and it would be the perfect time to install an SSD, incidentally.

• Some problems with the upgrade of RAM on Lenovo ThinkPad T500?

  Hello

  My laptop is Lenovo ThinkPad T500 and its main features as follows:

  -Processor Intel Core 2 Duo T9400 (2.53 GHz, 1066 MHz, 6MBL2).

  - 4 GB PC3 - 8500 DDR3 SDRAM 1067 MHz SODIMM Memory (2 DIMM).

  -ATI Mobility Radeon 3650 with 256 MB.

  I really need to upgrade the RAM to work with SharePoint 2010 and Windows Server 2008 R2. and my big question is:

  * How many memory locations that I have in my Lenovo ThinkPad T500?

  I read on (http://www-307.ibm.com/pc/support/site.wss/document.do?sitestyle=lenovo&lndocid=MIGR-55644#t) that the maximum memory size for T500 is 8 GB.

  Yes, in case if my Lenovo ThinkPad T500 laptop has only two memory slots, so, I'll have to buy 2 memory cards of ThinkPad 4 GB PC3-8500 DDR3 Low-halogen SO-DIMM, in order to get the 8 GB... and I have to throw my current memory cards...

  My other question is:

  * Is easy to install/remove RAM in Lenovo ThinkPad T500?

  Sorry to ask the second question, but I have never dealt with before material.

  I would appreciate your inputs.

  Thank you for your consideration of my request and I look forward to hearing from you soon!

  The T500 has only two slots of RAM, so the upgrade to 8 GB would mean that your two existing 2 GB modules would need to be removed.

  Replacement of the RAM is simple; Remove the four screws for the Palm and the locations of memory will be under the palm rest.

  See the HMM for more detailed instructions: http://www-307.ibm.com/pc/support/site.wss/MIGR-70068.html

• Upgrade of RAM for Satellite Pro S300-11

  Hello
  I have this netbook for two years now and I need to add more memory RAM, it has 2 GB and is capable of having up to 8 GB.
  I went to two local stores to buy a memory stick, but they are not able to find my netbook to their suppliers, so that they have no idea what memory modules could go well with my pc. I know that the installed RAM module is a DDR2 at 800 MHz. So, any module of ram with these specifications should work correctly?
  Another question is if my computer is able to read up to 8 GB or I have to upgrade the BIOS (I have not updated, so I have one pre-installed).
  Thanks for your reply and sorry for my English!
  See you soon!

  Hi manelfera,

  The laptop has Intel GM45 chipset and the chipset supports up to 8 GB of memory. This means that you can install 4 GB module in both memory slots. As you already wrote DDR2 800 MHz is the correct specification.

  Theoretically, each module with this specification will work, but I recommend the purchase of high quality of Kingston for example modules. I have good experiences with this brand :)

  Updating the BIOS is not necessary for the upgrade of RAM so you can keep the current version.

• HARD drive and upgrade of RAM for Satellite A200 1AE

  Hello

  I plan to upgrade my RAM and HARD drive.
  I am currently using a 120 GB SATA HDD and 2x512mb ddr2 667 Mhz (out of the box state).
  My questions are:

  [1] will a WD Scorpio blue work SATA II 500 GB HARD drive at 5400 RPM on my laptop? If this is not the case, what is the maximum GB for my laptop's HARD drive (if there are any)?
  [2] a 2x2gb ddr2 667 Mhz will work? If not, what is the maximum?

  BTW, the Specs are Intel Core2Duo 1.73 Ghz T5300's family Vista premium sp2 (preloaded) OS, BIOS Phoenix version 1.20, Chipset intel 945 (I think).

  Thanks in advance.

  > 1] will a WD Scorpio blue 500 GB 5400 RPM SATA II drive HARD work on my laptop?
  It should work since the SATA controller is not limited to any size of HARD drive.

  > [2] Will work 2x2gb ddr2 667 Mhz? If not, what is the maximum?
  The laptop supports Intel® 945 GM chipset. The upgrade of RAM depends on the chipset.
  AFAIK the 667 Mhz Rams should be clocked at 533 Mhz
  But you can upgrade it to 4 GB of RAM (2 x 2 GB)

• Satellite Pro A200 - new RAM work together

  Laptop Toshiba Satellite Pro A200-PSAF1A-003002, I bought the year last with RAM 2x512MB that I try to update my 3 GB RAM and I bought 2 RAM KTT667D2 / 1 G & KTT667D2 / 2G Kingston memory.

  I added that the 2 strips of RAM in the laptop, but it does not start. The power and the drive lights and flash for 3 times everything off. No boot. But I remove one of the sticks of RAM and it starts very well and the RAM has been upgraded in the system.

  I tried with the sticks and the two slots to remove 'bad slot' ideas and a stick of RAM works in a thin slot. Paste works in slot 1 or slot 2 and stick b works in slot 1 or 2, but not both at the same time. Is it simply a setting I'm missing somewhere? I checked the BIOS version is 1.7, I need to update my BIOS? Help, please

  Thank you
  Yana

  I think that the modules are not compatible together and that is the reason why each module works in each slot.

  Did you buy KTT667D2/1 and KTT667D2 / 2G. Different modules of s and are not working together.
  You should buy only the modules with the same specifications and capacity (for example, 2x1GB and 2x2gb).