Upgrade RAM problem new Alienware 15, 4 no beeps no boot.

Similar Questions

• Upgrading Ram problems

  Hi all

  I have a R4 Aurora alx 2012 build

  Sandy bridge i7 3820 gtx 980 sli, 8 gb of ram 1600 mhz cpu

  The island problem is ive bought 16 GB 4x4GB Corsair dominator platinum 2400 mhz ram and it does not start when it is installed?

  Ive tried all imaginable configurations with the sticks themselves, reset the cmos jumper, removed the cmos battery etcetc and still no joy.

  The system turns well but no signal on the screen even if all the lights of the fans and everything seem to work very well? There is no beeps at all, and obviously the Tower seems to think his job well, but no signal.

  I have replace the old 8 GB 1600 mhz original and everything sticks works fine?

  Any help would be greatly appreciated as I am scratching my head after having exhausted all remedies?

  Thank you

  Hi Steant,

  Looks like you've done what you can do. In this case, seems to me that the Aurora R4 is not compatible with 2400 MHz RAM. That or latency CASE of Aries is off from the design of the system.

  If you mixed the RAM, old and new, it works? Put 2 sticks of the original in both slots and the privateer in the other slots to see if you get anything then?

  ~ Jim

• HP Pavilion e002au-15 l: upgrading Ram problem

  Hi all

  I think to upgrade the RAM for my "HP Pavilion 15-e002au Notebook PC' and am faced with questions, some HP providers say I could go to 16 MB whereas some say it can withstand only 8 GB. Not sure which is correct and that the approval, please advice, my current setup is less to:

  OS: Win 8.1 - 64 bit

  2Memory containg 4 GB RAM Slots

  Please advice if I can spend my current GM 8 to 12 OR 16 GB of RAM.

  Thanks in advance

  Anil

  Hello Malygris1

  Thank you for your help

  Concerning
  Anil

• 32-bit to 64-bit upgrade RAM problems

  I recently went from 32 bit to 64 bit of Windows 7 Pro following the 'unofficial' resettlement Wiki (the second time around) to the letter.  Here what's happening: bought two sticks of 4 GB of DDR3 1600 MHz RAM 1.5 volt.  It is fully recognized in BIOS Rev A16. 3.8 GB is used and works perfectly under Windows 32 Bit.  When I attempt to load Windows in 64 bit I get 1) white screen to repair Windows loop - A & B charge 2-BSOD DIMMS when each stick is loaded in DIMM A only.

  The tension is incorrect?  Why these modules work perfectly in 32 bit?  Should I exchange for 1333 MHz to 1.35 volts?  Please notify

  Generally, I would go for Crucial RAM on Dell systems. We find that they sometimes accept always RAM of other providers. In this Crucial case is 1.35v modules:

  http://www.crucial.com/upgrade/Dell-memory/latitude/latitude+E6410-upgrades.html

  They also have PC3-12800 modules that will be the fastest. You can also consider an also however high capacity SSD are still quite expensive.

  This former pilot hidden, I'm not sure. Looking around it seems related with the Dell drive:

  http://ftp.Dell.com/app/Dell_Reader-2-0_A06_R272851.exe

  http://www.Dell.com/support/drivers/us/en/19/DriverDetails/product/latitude-E6410?driverId=4RM8G

• Upgrading RAM problem

  Hello, I have a laptop HP 350 G1 series i5 4210u (P/n: K4L54UT #ABA)

  I am looking into adding another RAM stick (identical to the ram in stock) on my laptop, however, I'm having a hard time finding the EXACT ram. I found the product to the RMA number in the manual and the stick itself (p/n: 691740-001), but there seems to be different versions of it. After that, I went back into ram for closer look. I noticed that many other numbers next to the product number, however, I have no idea if one of them is useful.

  Maybe is it useful?

  4 gb 1rx8 PC3L - 12800 s-11-11-B2

  Hello

  Please try how to buy:

  http://www.micron.com/support/how-to-buy

  Otherwise you can always order HP using part above (that's right B21).

  Kind regards.

• HP Pavilion b000no-13 upgrade RAM, problem with disassembly.

  Hello!

  I recently bought a HP Pavilion 13-b000no (I think that it is a "Europe/Scandinavia" model only) and have decided that I want to add 4 GB of additional ram (I checked that it is compatible).

  I searched all over the internet for the same model or similar on how to open it, but have not found anything useful. I then tried to do it myself, located all the screws unscrewed the but found that I couldn't open the back plastic without a chance to break.

  Here are some pictures of my attempt (too big files so had to use imgur).

  In yellow are all visible screws that I could find.

  Red, four additional screws under stickers (down two don't have behind them).

  Green is where I could "pry" open less than an inch and see the internal parts.

  Top of page interim sticker had no screws under.

  http://imgur.com/j8loKXj

  Here is a better view of the area where I could lift open the plastic a bit.

  http://imgur.com/KUh0gCh

  View of the keyboard where I can't find any place to 'pop' to the top (sorry for the finger) plastic.

  http://imgur.com/o7MbfXQ

  I tried to find a similar cell phone sold in the United States and this one comes pretty close, he has the same coverage as mine by the look of it.

  I appreciate all the help I can get!

  Thanks in advance!

  Here is the HP Maintenance and repair of your model that has detailed directions for disassembly.

  HP series 13 maintenance & repair manuals

  If you found my answer helpful please say thank you by clicking the s cursor Up icon. Thank you!

• After upgrading RAM, computer stops and gives error when restarting: "DISK BOOT FAILURE, INSERT SYSTEM DISK".

  Original title : OFFICE XP STOPS (MESSAGE of ERROR)

  I get the message "DISK BOOT FAILURE, INSERT SYSTEM DISK". I just added more memory to my 512 RAM. I USED MY XP TO REBOOT DISC, BUT THERE ARE ALWAYS AFTER PRESSING THE KEY 'R '. ONCE IT STARTS AND SE PAST JUST STOPS AND THE ERROR MESSAGE IS POSTER AGAIN UPWARD. I HAVE THE SAME 'MSCONFIGED' IT NORMAL TO SELECTIVE. I WAS ABLE TO GET INTO SAFE MODE, BUT NOW IT WON'T. I GET JUST THE ERROR MESSAGE.       > WHAT AM I DOING WRONG

  Hello

  You can view these methods:

  Method 1: As a first step, check to see if the hard disk becomes detected or listed in the Basic Input/Output system (BIOS). Also, be sure to change the boot order in the CMOS settings so that thehard drive is the first on the list.

  Note: To learn how, see the documentation provided with your computer or contact the manufacturer of your computer.

  Note: BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from configuration can resolved BIOS/CMOS settings. Changes to settings are at your own risk.

  Method 2: If the manufacturer has installed the Recovery Console on your computer, perform the check disk to fix this.

  At the recovery console command line, type:

  Chkdsk /r

  When you restart your system, your computer will be scanned for errors and will try to correct them.

  Note: Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.

  For more information, see:

  How to perform disk error checking in Windows XP

  Chkdsk

• (Redirected) Upgrade of RAM for my Alienware Area 51 R2

  I need to upgrade RAM in my Alienware Area 51 R2 currently having DD4-2133 Non ECC RAM, 8 GB in 2 homes, 4 GB each in Total. My question is, can I use DDR4-2133 RAM ECC, 16 GB stick in the four locations, a total of 64 GB of RAM?

  Better in this position in the Alienware owners Club Forum, here:

  http://en.community.Dell.com/Owners-Club/Alienware/default.aspx

  Bev.

• Satellite A300D-17F - problem with upgrading RAM

  Hi all.

  First sorry for my bad English. So the problem is my laptop has 4GB (2x2gb). I buy 1x4Go and I want to run with 6 GB. When I install my laptop (1x2Go/1x4Go) run in the bios write 6144 mb.

  But wen the bsod from windows... beginning some time the gel on the Welcome to windows and bsod screen.
  I tried evrerything run with 6 GB no success (once and show me the material 802 MB reserved after the next reboot bsod).

  Some time is running in Mode safe and write some use ram with linux Hardware Reserved.Under I have not problems: installed X 6 GB and no problem. A friend tells me that my shared video memory card to do conflict and cannot calculate the ram. Can I DISABLE my shared video card memory.

  The video card is not integrated.
  I'll give you all the information you will need...: «(want to just run this computer with 6 GB of ram... and no bsod...»

  I have test the ram. (NEW Corsair 1x4Go RAM) Memtest
  Don't test everything no problems with the hardware.
  Reinstall the windows (x 64) only.
  Stop the SuperFetch service.
  Install windows patches.
  I don't know what I'm doing more: "(.)"
  If can do disable the video memory?

  * Toshiba A300D-PSAKCE *.

  * ATI HD3650 512 MB *-http://imageshack.us/f/593/adaptermemory.png/

  DDR2-800 DDR2 SDRAM (6-6-6-18 @ 400 MHz) (5-5-5-15 @ 333 MHz) (4-4-4-12 @ 266 MHz) - and 2 Rams have the same calendar...

  * BIOS WITH 6 GB *-http://imageshack.us/photo/my-images/37/sdc12878y.jpg/

  * PHOENIX BIOS v3.30* - http://www.mediafire.com/?7ashzkqkk94v9ll

  * SOME OF BSOD HERE * - after windows logo or on the windows logo - http://imageshack.us/photo/my-images/43/sdc12873a.jpg/ / http://imageshack.us/photo/my-images/822/sdc12872v.jpg/ http://imageshack.us/photo/my-images/860/sdc12877.jpg/

  I thing if I disable the shared video (hypermemory) will fix the problem but how to disable? Have all of the options for this in the bios.

  Nice story, but the question is: you use the memory modules live compatible?
  In your long announce didn t post part number and manufacturer of your Ram for upgrade.

  Is that compatible RAMs will work perfectly and there is nothing you have to change, especially not some options of memory sharing that don t even exist.

  By the way:
  4 GB of RAM compatible have part number PA3670U-1M4G. Use this RAM and you won't have any problems, especially BSOD. BSOD is clear evidence that there is compatibility problem.

• Satellite Pro L20: I have problems of havi upgrading RAM

  I have problems to upgrade Ram.
  Sat Pro L20

  I have 2 sticks of 1 GB each, I tried in each slot and they work, but not all. Speed and size are the same but not associated. (apparently shouldn't matter)
  I'm annoyed about it, I'm sure it worked before, when I got a 1 GB and an assembled 256 MB

  Hello

  the modules are completely identical? They come from the same manufacturer? If not, then your problem is solved and you should go to the store where you purchased this RAM and exchange for a compatible.
  Usually this phenomenon appeared in only two cases:

  1. the modules are identical but one of them is faulty and it is the reason why they start won´t when it is matched
  2. the modules are not identical or not, from the same manufacturer they also start won´t when it is matched

  That's it, my friend. Nothing more to say.

  Welcome them

• Upgrade to the new Windows Live Messenger problem

  Hello

  In the course of running Windows XP Pro with service pack 3 and all updates installed.

  I had problem upgrading to the new Windows Live Messenger. So, I completely uninstalled messenger.

  I downloaded the last installation and I keep getting stopped on the installation with a window saying process:
  "Messenger could not be installed because we had difficulties to install this requirement: Microsoft Visual Studio Runtime." Try to download and reinstall these programs. One of the installation files seems to be corrupted. HR:0x800b004 ".

  I tried the 'Get help for this error', but no satisfaction. I have this problem everytime I try to install. I tried to re - download the file to install several times but the same results. Please, someone help!

  Thank you.

  Hello Styx007,

  The best place to ask your question of Windows Live is inside Windows Live help forums. Experts specialize in all things, Windows Live, and would be delighted to help you with your questions. Please choose a product below to be redirected to the appropriate community:

   

  Windows Live Mail

  Windows Live Hotmail

  Windows Live Messenger

  Looking for a different product to Windows Live? Visit the home page Windows Live Help for the complete list of Windows Live forums to www.windowslivehelp.com.

• I upgraded to a new computer with Yosemite, after have migrated my settings on, Dreamweaver CS 5.5 will not launch. It says it cannot find the menus.xml file, then the problem is getting worse.

  I upgraded to a new computer with Yosemite, after have migrated my settings on. Adobe CS5.5 works very well except Dreamweaver CS 5.5, it says it cannot locate the menus.xml file and cannot rebuild from a backup. He suggested resettlement.

  But when I try to reinstall, I get an error that says "Installer failed to initialize. Please download adobe support advisor to detect the problem.

  Who produces the net problem of it being abandoned, and that brought me here. Help!

  This is a duplicate thread.

  DW CS5.5 and Yosemite [subject edited by Moderator]

  Ultimately, the problem has been resolved by running the cleanup CC tools then by reinstalling the software.

  Nancy O.

• New Alienware Aurora R4 freezes every time in 50 minutes

  I just got my new Alienware Aurora and oh joy, my first time owning this beautiful Monster - looking for a machine.  I have owned it now for five 5 days; but the experience so far has been frustration, to put it lightly.

  The machine never stays more than 60 minutes at a time.  It crashes.  When it crashes, I hear the fans always roll the led still under the display theme AlienFX I put and it seems that everything is fine, but:

  1. the SCREEN turns off

  2. the keyboard does not work, systems is not responding to strikes again... as the keyboard is dead.

  3 mouse works now.

  4. nothing works, except the DVD tray that always comes out and in.

  5 only the resolution is to force close it down and then turning it back on, via the power button.

  I just installed MS Office, my keyboard and my mouse.  Nothing complicated.  I've now adjusted the power management to ensure that the disc hard system, display, etc. NEVER goes to SLEEP.  Yet, the machine still crashes as usual.  I'm not even games.  Simply creating a document, or watching a training video.  I even decided to just share my training on the Alienware video file and watch the video from another computer; accidents still Alienware and my video stops.  I decided to disable Windows Update, still problem persists.

  I checked EventViewer for clues, NOTHING.  No log entry for when the system unresponsive.  What kind of a computer is what the hell?  I thought that with Alienware, I won't have any hassles, but this has been an exercise in troubleshooting non-stop for me since I got this computer; It became a distraction, as whenever I sit down to work, I find myself troubleshoot the computer each time.  I'm now trying to force me to forget everything and just use my old laptop; that I supposedly replaced when I upgraded to this Alienware machine.

  It's Sunday today, I intend to call technical support for Dell tomorrow to start the support process.  But to give up some lines here just to get feedback / if there are similar experiences that can shed some light on this problem.

  Please any response that can point me in the right direction will be appreciated.

  Hello

  Yes.  A quick update from my post.  I called Dell technical support on Monday 20 October 2014 and the guys were fantastic.  I spoke with a guy named Bogdan; He spent almost 3 hours working with me on the problem over the phone.

  I'll give you a detailed below:

  At the time that I called him, the computer was no longer able to boot the system.  This is because the previous night, I have run AlienRespawn default factory reset, but the shutdown of PC in the process and then was not start over; and instead showed the blue screen.

  So on the phone with Technical Support, we used AlienRespawn USB backup I had created the first day to reset the computer back to factory default.  And then I connected and put things up so that he can have the remote connection to the computer.  As soon as he connected, the computer decided to die just so :).  So we decided to do the Reboot usual cold.  And once again, as soon as it is connected and looking to run some test, the computer exploded again.

  On the third attempt, the computer remained.

  Bogdan then via a remote connection session, several controls and ran several stress-tests on virtually everything (RAM, CPU, graphics, etc.).  All tests came out, as adopted.  And then we installed software to monitor temperature and other stats like stress tests were running; all readings were really good.  Source of the problem was not yet clear.  We have been jointly shrink on two possible culprits, the graphics card or motherboard (or both in the worst case).

  As we are still brainstorming and then try the AlienFX theme colors, the computer decided that it was time to STOP, once again.  And this time it faced a 6 six sound beeps sound sequence several times.  He did this once before, the previous week.

  The machine had a mind of your own.  It was very random behaviors all the time.  He gave beeps when he wanted to.  He has changed the settings of the BIOS on its own; change the default settings, mode strives / EUFI, etc at random :).

  So we turned and technical support preserved in tests.  He also uninstalled and reinstalled the updated version of the Alienware Command Center.  Even after that, all the readings and the results were perfect, but then Switched OFF the machine once again.

  Makes technical support a call to change the four main components: motherboard, graphics card, MasterBoard and Water-Cooling system for the next day.   So I was expecting an engineer for the next day.  That evening, I decided to install all my software and turn on the computer to a State that is useful for my work and play.

  The morning next day (Tuesday), I decided to continue to use the computer and just keep restarting it out every time.  And then, at some point given around 10:00, he remained THERE for nearly two hours (first time he stayed on this long), I was pretty sure that the problem had gone for an unknown reason.  And to share the joy with my Mrs, the machine went OFF :).

  And this time it's completely DEAD.  It was not turn on anymore.  The LEDs and fan are turning on, but not to life on the screen, the keyboard or the mouse.  It remained so until the Dell technician came.

  To my delight, a Dell technician was at my door at about 14:00, with all the necessary parts.  He was also very friendly and empathetic.  He quickly set to work and replaced all suspect parts.  We went ON and, oh joy :).  The machine came back running.

  He made all necessary BIOS settings and my machine was fully operational.

  I used it for almost 2 days now and no problems at all so far.  It's been great, even if sometimes it's like the trauma remains... I still fear that he might simply turn off on me anytime.  But so far so good.

  So I can say at this moment, the issue is resolved and my device is fully operational.  Thanks for the support.  I hope that my very long story somehow help others who have a similar experience with their machine.

• Satellite A105-S2051 and XPSP3 - upgrade RAM and hot key error

  Merry Christmas together,
  Please can some mention help: have Windows XP HOME SP3

  1. recently tried to improve my Satellite A105-S2051 950Mo to MAX 2 GB RAM. I have x 2 places available.
  2 a RAM problem, pc would not even turn when the two new ram sticks have been installed.
  3. If x 1 old used module and x 1 new stick of ram, pc would not record even installed extra RAM? After discussion with the manufacturer recommended to also upgrade my old BIOS suppliers, I did it via the load - SAME support.
  4. then they recommend - sent back 4 RAM chip, they returned with the type of chip 8,.
  5. upon receipt, PC would not turn on once more if the two 1 GB installed? While could then install x 1 old + x 1 new, pc recognizes the additional ram 1 x, 1.36 GB memory stick.
  6. have you tried to load keyboard shortcuts available on download media files to find error - Toshiba ACPI common Modules (TVALD) missing?
  8 tried to load files TVALD, to then find error - TVALZ DRIVER FAILED? aaaaaaaaaaahhhhhhhh
  Any help would be most appreciated, Please help!

  Kind regards

  Paul.

  There is no reason to discuss on the RAM upgrade, because things are clear: RAM upgrade will be successful if you use only compatible modules and module 1 GB for your laptop with PA3411U-2M1G part number.

  Use two of them, and everything will be OK.

  Back to WXP stuff.
  Installation of WXP can be quite complicated as all things, especially specific tools Toshiba and public services must be installed in the correct order. Before you begin to install Toshiba stuff, you must install common modules. It is a fundamental tool, and it must be installed first. Problem is that we support for your laptop model page, I can't find common modules for download.

  What you can try is to install from the European page. You can find it HERE. Check it out.

• HP all-in - One PC 19-2113w 19: white/black screen after upgrading RAM

  Hello

  So I have upgraded RAM using 2 x 4 GB SODIMM DDR3 Corsair 1600 Mhz, after installing the PC boots but screen is white/black

  steps to follow:

  1. I tried with 1 socket by using only a RAM, screen black

  2. I tried with 2 socket using RAM only one with the same RAM step 1, screen black

  3. I tried step 1 and 2 using the other RAM, screen black

  now here it gets interesting

  4 tried 1 socket using Original/factory RAM, screen black

  5 tried 2 socket using Original/factory RAM, screen black

  6. tried without any RAM at all, looks like a lack of RAM, screen black

  Now, to each measure adopted, I must say that the screen sound not only not showing things, but its totally black as it does at all, until the system starts normally. !

  Is it Possible the upgrade of RAM affect the screen? or maybe when I was replacing the RAM I hit some conecting by cable to screen or something?

  HP 19 all-in-ONE PC

  Product No.G4B06AA #ABA

  Model n ° 19-2113w

  10 64-bit Windows

  Update

  Removed the battery and hold the power for 30 sec button (BIOS reset if I'm not mistaken?) now it works with the orginal of RAM so I guess my new RAM that's the problem!