Connection to the router problem WRT160Nv2 WUSBF54G

Similar Questions

• 9.3.4 disabled wifi on an Ipad, but it connects to the router. Just don't download at all

  IPad was working fine, but I've updated to 9.3.4. Now Wireless does not work. Shows connected to the router, but nothing happens, but say unable to connect to the server, error trying to access the internet or by mail. Also turn continuous flashing VPN gray to green, then again, but we have never set up a virtual private network. Don't know if it is connected. Have you tried

  1 disconnection / reconnection to 2 routers that work very well for other devices

  2 reset wireless via settings > general > reset > reset network settings and then hang up again

  3 airplane mode on, wait a few minutes, then shut off again

  Overall, the router will connect to any time, we put the password, but there is no transfer of data. 3 other devices work fine with the router. Don't know where to go from here, or if it is possible to back out from the upgrade. Anyone else having this problem? A research increase the same problem.

  Thank you

  Anything that causes the problem is not specifically 9.3.4, which fixes just a security breach. Have you tried to restart routers?

• HP Envy 4500: Printer connected to the router, but will not print wireless Macbook

  I want my wireless printer to work on my macbook, but I can't. I tried setting up on the HP utility to connect with the router as the mac and printer on but it does not work! It indicates that the download was successful, but the device was not reachable. I don't really know where to go from here and any help would be really appreciated. Thank you.

  Hey @miriamnimmo,

  Welcome to the Forums of HP, I would be happy to help you! I understand that you have the printer set up on your network, but the software says that the device is not accessible. Sometimes the IPv6 may interfere with the connection, and I suggest we disable that before anything else. On the fornt of the printer Panel, scroll down to and then select Wireless. In the wireless Menu, select Advanced settings, then IPv6 and.

  Now we are going to let the router and unplug the power cable (NOTE: do not reset the router), then do the same with the printer and shut down the computer. After a minute, plug in the router, wait to fully turn on, then plug the printer back in and wait for the wireless light become solid. Once the router and the printer are on, go ahead and re - turn on the computer. This will refresh the network connection.

  Please let me know if this solves the problem by marking your post as solved (click on Accept as Solution button below). If the problem persists, let me know, I'll watch for your reply.

  See you soon!

• 15 - r074TU: laptop does not connect to the router

  Day sum... .my laptop (model No. 15r074TU) with window 8.1 does not connect to the router that is D-link

  I uninstalled my driver reinstalled again, but it didn't work... even if I formatted my laptop, reconfigure the router and... done with all possible measures to overcome this problem, but have ultimately failed. Please suggest ways to tackle this problem as soon as possible...

  Follow the wizards in the following forum sticky and troubleshooting.

  http://h30434.www3.HP.com/T5/notebook-wireless-and-networking/common-fixes-for-wireless-connectivity-issues/m-p/4831601#M86871

• iMac connects to the router of Linkysys WRT1900ac

  I am trying to help a friend get his iMac 12.1, that is running 10.11.4, to connect to a new Linksys WRT1900ac router.  The router is a novelty in this House, is in the same room of 10 x 12, as the computers listed below, and the installer was using the Linksys recommends the method, which is to let the Linksys to make adjustments.

  Here are its configuration;

  The router is connected to a cable modem, ISP and the following devices are connected to the router and works well;

  Via ethernet

  Windows 10 PC

  AT & T cell phone extender

  Ooma VOIP

  Wireless

  iPhone

  iPad

  Notebook PC

  While troubleshooting my MacBook 5.1 also allows to connect without problems to the Linksys router.

  Note that her iMac connects without problem to the wifi network Netgear Guest unprotected from its neighbor.  I also installed in his room my 1st generation Airport Express, which has added a second wifi network but without access to the internet and his iMac connect without problems to this wifi.

  Here are the steps I took to try to solve this problem, and they were unsuccessful;

  ➔ Scanned for malware/adware with Malwarebytes and found nothing.

  ➔ Ransacked after the files in/Library/Preferences/SystemConfiguration and restarted

  com Apple.Airport.Preferences.plist
  NetworkInterfaces.plist
  Preferences.plist

  ➔ When the previous did not work I trashed all the files in the folder/Library/Preferences/SystemConfiguration except "com.apple.boot.plist', which would not remove and rebooted

  ➔ Created a second user account and still not able to connect to the Linksys router

  ➔ Repaired permissions

  ➔ Created a new location in System Preferences > network and added the OpenDNS addresses and in the material value MTU 1453

  ➔ restarted in safe mode and not still could not connect

  Firmware on the router Checked ➔, which is updated

  ➔ Reset SMC

  ➔ reinstalled El Capitan via the App Store

  That's all I could think about.  I'm puzzled.

  I checked the router and everything seems ok, but I'm no expert.  There may be something I'm not contagious.  I have seen that he has no MAC filtering set up in the router, so this isn't everything.

  Please tell me if there is something that I'm on.  Is there something in the router, that I need to change?  There are other files in the Mac, I need to delete?  Is there any other troubleshooting steps I can take to identify this problem.

  Any help would be appreciated as it is a total mystery to me.

  There are a lot of variables, but start with some basic info. So on her iMac, if you click the wifi at the top right, you can see his router listed?

• Unable to connect to the router WLan - Satellite L300D

  Please help me so that I have still a few hairs left!

  I installed WLAN driver on my laptop Satellite L300D with Vista Home installed.

  I see my network in the available connections, but when I go to connect, it will not connect.

  My other two desktop computers can connect to the router without a problem.

  Any suggestions?

  Thank you
  Neil

  Hello

  I think that you didn t try updates. Right?
  Therefore, my first recommendation would be an update of the BIOS and driver WLan.

  Check the current version of the BIOS that is available on your laptop. If the latest version has been released then update the BIOS.
  In addition, to download the latest WLan driver from the Toshiba WLan portal and to update:
  http://APS2.toshiba-tro.de/WLAN/

  On this Wlan site, you will find three different WLan drivers for three types of WLan cards. First check your wireless network card, and then use the right driver!

  See you soon

• Samsung S6 connects to the router but no internet

  When I switched to xfinity I bought a C6300. I had problems with the first not allowing my NAS to connect so I exchanged against another. My phone would connect to the router and work fine for awhile then lose Internet connectivity. The only way to get it back is to reboot the router. I tried several different units, and I am now on a C3700. The problem still exists and seems to be deteriorating. All of the suggestions.

  I solved my problem by replacing the Netgear with a Zoom. It was the only one that I could find who said it would work with Android. I hope that Netgear will get things straightened.

• M40X connects to the router Netgear DG834G wireless

  Message on the toolbar and warnings are; No limited connectivity or. Improved Intel Pro wireless 2200BG driver worm 9.0.4.8 without success.
  I have another laptop with a USB wireless network too and that works very well.
  I was able to connect to the router via the ethernet card.
  Been on Netgear, and the router works well.
  Any ideas, anyone please...

  Hello

  I guess that your laptop uses the map Intel 2200BG wireless.
  You will find a lot of questions and problems with this card intel.
  Mainly the graphics driver update will solve these issues.
  You can also check the power save mode settings in the properties of the wireless card. Go to the Device Manager, choose the wireless card and go to properties. In the second Advanced tab you should find the Power save mode option. Please switch off (off)

  I put t know where you download the driver, but you must use the latest version on the Intel site.

• Unable to connect to the router

  -Please ignore this message: I did not wait enough to do the factory reset. It seems that launch a factory reset without waiting for 10 seconds only restarts the router.

  Hello

  Today I tried to connect to my router (I do not use it for a few years) and it didn't work at all.

  Initially, I plugged it in just 2 RJ45 cables: one for internet, one for the PC. The computer could not connect to the router (DHCP failed).

  I then restored the factory settings and tried again: same thing, the computer could not find the router via DHCP.

  I tried to force an IP address (IP: 192.168.1.5, mask: 255.255.255.0 Gateway: 192.168.1.1).

  By forcing the INVESTIGATION period, I was able to connect to the router, but when I tried connect to 192.168.1.1 with admin/password, it wouldn't let me (bad password - don't forget I restored it to factory settings, several times actually). The address http://routeurlogin.net/ is not found (404) and I was unable to go on websites (404). A curious thing is, using this connection, I was able to connect to Skype (and send/receive messages), although the sites Web could not be reached from a browser.

  I'm running out of ideas to solve the problem, but I suspect a hardware problem, so any help would be welcome.

  Yes he did.

  I couldn't find an option to delete my message, otherwise I would have done it.

• Satellite L500D: WiFi remove connections to the router

  My bars of Toshi Saturday 1,2,3,5 equates to dropped the WiFi but when WiFi is at 4 bars, it's the best thing since the fire.

  Recently, my laptop started to remove connections to the router and the router is that a step of 4-5 come out in the kitchen of my house. And another problem is that my room seems to be a dead zone.

  If I turn on my laptop, I am required to get out of the kitchen and stand near the router until it connected, but if I'm sitting in my room, 3 bars, and said "(the WiFi name) cannot be detected/connected."

  Any who want to enlighten me on what's going on?

  Mr.Delta

  Simply said, the Wlan router signal is too weak and this causes disconnection
  I have some advice for you;

  -Update the WLan driver
  -Card Wlan definition of control; You should go to Device Manager-> properties-> Advanced tab WLan card. You will find some options that allows you to change the standard WLan (802.11 A, B, G, etc.) and you can also check the WLan channel and improve the signal
  -Disable the Wlan Card saving

  Good luck

• Want 5660: Printer cannot connect to the router

  All of a sudden the printer can no longer connect wireless to the router. Printer router ok may be defective

  Please provide the following information if anyone can help including:

  The printer model - done

  Operating system of the computer-

  Detailed - description of problem including all devices network (extensor, switches)

  Connection method - Direct wireless, wireless, wired LAN, USB? -

  Number of brand and model of router and modem? -

  Error messages - on the screen of the printer or computer, no matter what flashing light patterns? –

  The printer is connected directly to the wall outlet?  If this isn't the case, please explain how the power is connected.

  Do you think the printer is going to sleep and can't wake up? -

  If wireless, in the event of problem, what is the status of the blue wireless light on the printer, active, disabled or flashing? –

  Power off the printer and the router.  Power on the router and wait 3 minutes, power on the printer.  It connects to the router now?  What is the IP address of printers?

• Lexmark printer will not connect to the router

  Original title: HELP

  I switched to Fios and now have a new modem/router and I don't know how to get my Lexmark printer to recognize. How can I solve this problem?

  Hello

  Thanks for posting the question in the Microsoft Community!

  The Lexmark printer will not connect to the router/modem.

  Because the problem is with the Lexmark printer cannot connect to the router, I suggest contact you the Lexmark support team in order to get help with this question.

  You can try to get help on the site:

  http://support.Lexmark.com/index?page=productSelection&channel=supportAndDownloads&locale=en&UserLocale=en_US

  If you need any help or if you encounter problems with Windows in the future, let us know and we would be happy to help you.

• While trying to install a Linksys E1500 he repeats that my computer is not connected to the router.

  Computer problems and the router

  I have a windows xp 2002 with service Pack 3. While trying to install a Linksys E1500 he repeats that my computer is not connected to the router. Ive tried a new cable and it does not solve the problem. He also said that my computer does not have wireless capabilities. Any suggestions?

  You'll be much more likely to get useful (or even possible) suggestions if you provide the full text of the error messages you get, without paraphrasing.

  For example:

  He repeated to me that my computer is not connected to the router. --> What is the real error message?

  He also said that my computer lacks wireless capabilities--> what is the error message itself?

  You are "trying to connect via a cable" to the router or you're talking about your Internet service (for example, the router is connected to the Internet via a cable)?

  You think that your computer has "wireless capabilities?  Open the Device Manager (start > run > devmgmt.msc > OK), then click on the + sign next to "network adapters."  Please provide the names of any devices listed there.

  Is your computer without a name, a laptop?  There a name of brand anywhere (for example, Toshiba, HP, Dell, etc.)?

  Open System Properties (start > run > msinfo32 > OK)
  Click Edit > select all
  Click Edit > copy
  Right-click in your response here and select Paste
  Be sure to hide the "System name" or "User Name" if it makes you feel better, but please do not remove anything else.

• my wifi stopped working suddenly. It shows no available networks. However, another iphone is able to connect to the router. Help, please

  my wifi stopped working suddenly. It shows no available networks. However, another iphone is able to connect to the router. Help, please

  Hello

  1 have you made changes to your computer recently?

  2 are you able to access the Internet through an Ethernet cable?

  I suggest you to follow the steps in the link and check if it helps.

  Windows wireless and wired network connection problems

  I hope this helps.

• LaserJet P1102W: Hp p1102w, connect to the router

  Printing wireless Dell desktop (Win 8), Dell (8 Win) laptop (Win 7) Dell laptop and rarely with the iPhone 6 and iPad Air.  All are physically within 30 feet of Cradlepoint router MBR95 that is filled to the voice/date Arris TG862g with ISP Comcast modem (20 to 25 Mbit/s on average).  Printing can be VERY slow with documents of modest size.  The printer is physically next to the router that has a USB port.  What should I do to use the HP printer cable to connect to the router to print non-wifi from PC 3?  (I assume that this configuration will solve the slow printing problem.)  And, if so, I'll be able to print also wireless of the iPad and the iPhone?

  Looks like your choice on this printer is wireless or USB. It seems not to be an Ethernet connector. USB would require that you want to run the file and printer sharing. Unless your router has a USB connector supported of printer.  You say id has a USB port, so now, you should check this one supports the printers.

  Wireless... the printer must be at least 6 feet from your router.