* Urgent * Weblogic 10.3 is not accessible after change the way administrator

Similar Questions

• Office Jet 6500 will not print after changing the ink cartridges

  Office Jet 6500 will not print after changing the ink cartridges

  Hello

  This doesn't seem to be a problem with the printer itself and not Windows. I also suggest to contact the manufacturer. In this case, HP.

  Please see here: http://www8.hp.com/us/en/support-drivers.html

• HARD does not work after changing the disk partitions recovery media creator

  Hello world

  After installing windoows 8.1 April major upgrade (win 8.1 presents as OEM), and have shrunk C partition to create a data partition "D", "Troubleshooting" option under advanced start menu is no longer available.

  Toshiba Recovery Media Creator does not work, too (it can not find any hard disk recovery partion).
  I got in the OEM recovery partition.
  I am also able to create a recovery using the Windows tool unit.
  You have no idea about it?

  Thank you very much!

  Hello

  Sorry to hear about all this. Unfortunately, you now have a big problem. I don't understand why you didn't create support of recovery before you started to change the factory settings, including to change the structure of the partitions of HARD drive.

  Mobile offered with factory settings a structure specific partitions and recovery recorded image is saved on the partition of drive specific and marked with invisible markers. These markers are visible for preinstalled Toshiba recovery media creator tool and when you start the tool can find points of reference and has full access to specific files.

  Unfortunately, after changing the original scores structure Toshiba tool cannot find these markers more and is not able to copy files from recovery media recovery. What you need now is the original recovery disk. Using this disk, you can install original recovery image and after doing this, you will have new factory settings.

  I know it sounds stupid now but you must order the original recovery disk and it can be done on https://backupmedia.toshiba.eu/landing.aspx

  If you have any other questions you are welcome.

• HP laserjet p1006: does not print after changing the toner

  I just changed the toner. The green light is on, but when something I send to the printer to print, the orange error light. Before inserting the toner, I pulled the Strip in transparent plastic attached to an orange tongue and the black cloth. I tried to reinsert the toner and turn on/off the printer again. Help please if you can. Thank you!

  Hi @cindycb,

  Welcome to the Forums of HP Support! I read your post and to see that when you try to print after changing the toner, the Attention light. I would like to help you today. If this helps you to find a solution, please click on the button "Accept as Solution" down below in this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

  Make sure all the orange, packaging material is to remove the toner.

  Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector) This ensures that the printer is full on and can help this situation.

  Try and print a self-test on the printer hardware to see if it is a hardware or software problem.

  Open and close the cover five times quickly. It should print a page with black lines on it.

  You can find the flashing light distribution in this document and the right solutions for the reason that you are experiencing, lights blinking on HP LaserJet P1005, P1006, P1007, P1008 and P1009 Printer Series.

  You use Genuine HP Toner?

  Please let me know the result and if there is anything else I can help you. Thank you.

• gSynchit does not open after changing the password

  GSynchit has stopped working. I changed the password of email account, but the program does not open if I can change the settings.

  Hello

  1. what operating system do you use?

  2. What mail client do you use?

  3 did you receive an error message when you try to run gSychit

  If you use windows7, I suggest you follow the link and check.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: After a repair, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

• Problem with the files not showing (after changing the USB mode)

  I have a sansa fuze 4 GB. version V02.01.09A. OS: Vista Service Pack 1. My rocket was working fine until about a week ago, when it stopped charging. but after installing the new norton 360 sansa is more appeared in my computer or Windows media player at all. I tried updating the driver but it says that the pilot was already up to date. I tried other USB ports again (front and rear), did not work. I decided to change the USB mode and it has finally started to load again in MSC mode.

  now, for the problem I currently have and, when I click on sansa via my computer and go to the music folder, it says "this folder is empty". I unplugged and watched in my music list, and all the music is there. I tried to put a new song on the player, disconnected, and when looking through the songs of the player the new song is here. I reconnected it, the new song is in the music folder, but the other songs are not listed. In addition, I have a microSD card that is listed as "o" in the car, all the songs I had on this appear, but not those on memory internal to the sansa.

  How can I get again list all music files in the folder?

  Note: I do not sync as it has only some of the songs I want on my sansa. the way I add songs is to copy and paste to the folder of the sansa player

  Okay, I don't know why or how, but it works now in MTP mode. I saw you are solutions, but I decided I'll just change the mode before trying to have ideas. until I reconnected it I also removed the microSD card, and it worked perfectly (make a backup of my songs). the problem could have the sd card in all this time?

• System does not boot after changing the appearance settings

  I installed XP Home successfully, but the resolution of the screen to be changed. When I followed the instructions of troubleshooting, I was unable to get to the drivers. I changed the settings on the advanced screen prompt to auto, and now after the Windows XP logo load and it I hear the hard drive running, the next screen is completely white/black. Help!

  Is this the same solution for: in the advanced options of monitor, I selected "do not use this device"?  I tried to update the driver for the monitor and reach for straws when the button 'update driver' has been 'grayed out' (not available).  I have a new HP 2009 flat screen and have just installed XP on a new hard drive.  Monitor worked, although some resolution.  The type of monitor has been defined as "default monitor" and driver is VgaSave.  Thank you!

• HP 6520 will not work after changing the black ink cartridges

  Changed the cartridges and now black ink will not work. This is the second or third time only to change the cartridges - did not have a problem before, but of course, it is while the printer was still under warranty. It is now about a year and a half.

  I used all the suggested diagnosis - head cleaned, head aligned, etc, etc, etc, and nothing has helped.

  The black cartridge worked after the swap, but with a few lines do not print or missing--now produces almost nothing.

  Cartridges color was wonderful at the beginning of the troubleshooting process, but now they're starting to not look right - with spare no effort to correct the print head, he seems to be making it worse.

  Suggestions?

  @scrdagain

  I will send you a private message (departure from the envelope at the top on the right)

• OptiPlex 755 USFF does not start after changing the cmos battery

  I have a desktop Optiplex 755 USFF requiring the cmos battery to replace. After the replacement of the computer will not start. It brings up the menu windows start, the sasfe mode, safe mode with network set mode command prompt, security, last know good configuration and boot normally. Any option will bring to the top of the WIndows XP loading screen and then re-boot of the computer right back to the start screen. A big loop. I can get the hard drive to boot in an Optiplex GX280 without problem. I was told of the motherboard needs to be replaced, but I changed the units of the system and the same thing with this hard drive.

  I tried to reinstall the operating system and get all the way to "starting windows" and then the blue screen stop error message 0x0000007B (0xF7A10524, 0xC0000034, 0x00000000, 0x00000000) dead. The computer is WIndows XP SP3, 1 GB of ram with 80 GB hard drive. It seems that the Setup program does not recognize the hard drive.

  Any help would be appreciated.

  After several hours of experimentation, I finally found the correct BIOS settings in order to get the computer to boot. There are three BIOS settings that need to be changed or check settings by default so that it can work. SATA 0 must be activated, SATA operations must be changed from AHCI, ATA and in the modular Bay, by default "far-sighted" should be replaced by the IDE. Save the settings and start the computer to the right upwards.

• Windows 7 does not update after changing the BIOS battery

  I recently changed the BIOS battery for my desktop which runs on Windows 7. Even after that windows 7 is not able to update.

  Windows Update checks the updates forever!

  

  the action center has this message:

  

  and the history of the update is like that...

  

  I also tried the tool micrsoft 'Fix it '. It was of no use. Windows Update stopped for checking updates and gave the error: "80072f8f.

  Can someone please help to fix this error, this will also allow me to upgrade to Windows 10!

  Thank you.

  Use the following tutorial to reset Windows updates completely and check if it helps:

  Full updates to reset Windows

• Satellite Pro L40 does not start after changing the BIOS settings

  Changed some settings in the bios last night and now when I boot I get a screen black lights flash and hard drive lights up but nothing on the screen.

  There is no password on the bios... How would a BIOS reset to normal?

  I put a windows disc now, I hear the disc spin but nothing on the screen

  (I think that I have come to the right place on the forum)

  It s a Toshiba Satellite Pro L40 model psl4be.

  Thank you

  > There was no bios password... How would a BIOS reset to normal?

  You can set the default BIOS ONLY inside the BIOS access BIOS by pressing F2 or at the beginning of the initialization of the order

  But I doubt that this problem is related to the BIOS.
  Maybe it s just a simple bad luck that this problem happened exactly after change something in the BIOS.

  Try connecting an external monitor and check if you can see something on the 2nd screen.

• XP pro do not start after changing the Boot.ini file

  The problem is that my C: partition Windows 7
  D: has XP Pro

  These should be considered right resp. partitions 1 and 2?

  I wanted to first XP pro to start the default partition.

  A few days ago, I made a change to the boot.ini file. But since XP Pro was not starting at all.

  I tried XP Pro to start first that the default partition.

  Given that XP Pro and my D: drive have not been starting, I consulted the boot.ini file in C:, Windows 7 partition and I changed the order (i.e. partition No.) in the boot.ini file and saved it to the required location, i.e. D:/WINDOWS/pss.
  through my drive C: of work, i.e. the partition of Windows 7, but it still does not work because apparently even though I save here, the actual values and the paths of the partition are not actually be changed on the system. I confirmed this by going into the CMD shell switching to D: and by running the command D: > bootcfg.
  Apparently any values I save in the boot.ini file that I save as a text file or "All files" in D:/WINDOWS/pss/it does not actually change in the system because whenever I run the command bootfg values are remaining still and not able to be changed, because apparently it is not saved in XP Pro and the D : partition. No matter what I do and what I put in the boot.ini file to access the values through the windows 7 partition, the values that bootcfg returns me are always the same and he refuses to change the name of path or anything else. No matter what orders, I also put in bootcfg himself.

  These are the values that bootcfg gives me:
  default: multi (0) disk (0) rdisk (0) partition (1) \WINDOWS

  Boot entries:
  Boot entry ID: 1
  Friendly name of operating system: MS Windows XP Professional
  Path: multi (0) disk (0) rdisk (0) partition (1) \WINDOWS
  The operating system load options: / noexecute = OPTIN/FASTDETECT/usepmtimer

  My XP Pro partition is simply not booting, and it of my main partition and has all my work. It is imperative that it starts.

  My Windows CD is also not start because apparently my DVD drive does not work properly, I had the anti malware threatfire (ThreatFire) installed on my XP D:Windows program disk but have uninstalled just in case it was blocking my changes to the system.

  On C:Win7, I put the default operating system option in the Advanced tab for Win7 and the D:XP Pro to XP Pro, when he was the starter and work. Now I can only access my files D:XP Pro Player C:Win7. But XP is not just start. What shd - I do? Thks.

  I don't have a very practical windows CD but my CD/DVD drive is not read and does not properly.

  Looks like your original post stated that your cd/dvd does not work.

  Respectfully, you will continue these hap hazard patches and your computer will not start at all. I'll try to help you once again. Please follow closely.

  Start your computer by loading Windows 7. Click HERE and download EasyBCD. Install the software in trial version. Once installation is complete open EasyBCD. You will see an interface like the image below. Click Add a new entry.

  

  A new screen appears as in the image below. Use the drop down menu to select Windows NT / 2 k/XP / 2 k 3 as described below. Type the name of the operating system in the box below. Of course, it will be Windows Xp (you can add the home or Pro to the name if you want). Make sure now that there is a check mark in the box "automatically detect the correct player. Once you have completed these steps click on 'add an entry '. That's all! You are finished. If all goes well, and if you have followed these steps carefully, there, now you have a system dual boot.

  

  You can now start working on your cd/dvd problem.

• Keyboard shortcuts do not work after changing the blending mode to a layer

  There is a strange bug that I experienced with photoshop. Whenever I change the blending mode to a layer (for example by selecting "Multiply" in the menu drop-down blending mode), my keyboard shortcuts stop working until I have click on the canvas again. It's annoying because often, I'll be on the Brush tool and I did draw on the canvas and press ctrl + z to re - activate keyboard shortcuts. I'm curious to know if this problem occurs to someone else and if anyone has found a solution for this.

  Version of Photoshop: 20150722r.168 x 64

  Operating system: Windows 10

  It happens on Windows, because the drop-down list with blend modes remains highlighted or active (around the blue line). You can press ENTER to confirm and delete the highest point around blend mode dropdown or use keyboard shortcuts to change the layer blending mode. To change the layer blend mode, you must have selected layer and then press Shift + Alt + letter for the blend mode. This shortcut does not work in the case where the tool you are using have mode option in the blending Options bar.

• VCenter Service does not start after changing the port number

  Hi all

  Accidentally, I changed the port number for the Vcenter server from the portal of VCenter 10443 and dint realize that the Java application uses 10443 so.

  Could not start the server vcenter service, because its raise an error saying 10443 port is already im currently byt used another application.

  I tried to stop the Java service, in order to start the vcenter service and make changes to port again, numbers but I am unable to stop the java application.

  Please, if anyone knows how to change the number of Vcenter via config port or any other way, please throw a comment... Its much appreciated.

  Thank you

  Nirmal

  If you use the MSSQL database, locate WebService.Ports.http in the VPX_PARAMETER table and change to the correct port.

• vCenter WebClient does not work after changing the field of vCenter Server

  Hi all

  I had to migrate my vCenter to a new domain. This migration is smooth without any problems. Everything works fine.

  Now, some of my colleagues need to use the web Client and I discovered, after to be authenticated successfully to the web server,

  I have an error message:

  Unable to connect to vCenter Inventory Service - _ https://vcenter._olddomainname: 10443

  Thus, even after reinstalling the Web server on my vCenterServer (version 5-update1) component, it always uses old domain information.

  I can't find where to change it.

  Hope you can help me with that.

  Thanks in advance,

  Frank

  Have you tried to run the command as shown in register.bat

  http://pubs.vmware.com/vsphere-50/index.jsp?topic=%2Fcom.vmware.vsphere.install.doc_50%2FGUID-9C65879E-7442-46E2-9A20-A858B2800D12.html?