USB, dead after install XP Professional on 1850-S801 - HELP!

Similar Questions

• No sound after installing windows on my hp 620 help 8

  No sound after installing windows on my hp 620 help 8

  I can't find your audio driver on the HP support page, but I was able to locate it, which is the same engine as yours, just the latest version. According to what is listed, it supports Windows 8. Give it a shot and let me know if it works for you.

  http://goo.GL/0IMBd

• Satellite NB10t-A-101 - USB works after installed Ubuntu 14.04

  Hello!

  After installing ubuntu with the process that you gave to me
  (here: http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=76813)
  and after a few days of use without problem, my USB port have been disabled.

  You have an idea how to deal with to bring them back?
  If you want any information that will help you, just ask.

  Thanks for the help

  With the USB mouse connected, open terminal and enter: lsusb

  You see the mouse?

  In addition you can wear the battery for at least a minute properly deliver material. Then put back the battery and check if the USB ports are not working.

  Last but not least, you could try to start the device using Live didk/USB to see if the problem is still there.

• Can not update after installing CS5 for hard drive nine, help?

  I installed CS5 Design Premium for my new hard drive, the installation was successful. However, the update has failed. Feedback from the failure: "there was an error downloading this update. Quit and try again later. "When I press the customer support for comments, he directs me to a web saying:" error "this serial number is not for a product calling..." "" When you install an upgrade or upsell.

  So, I ask for the help of discussion online and asked me to seek help from the Forum after got my serial number.

  Help, please.

  Thanks HK online help that does not give me the solution immediately because CS5 support has ceased. However, she suggests to find and install Adobe Application Manager 5.0. However, I have not found the software but I found one (probably 8.0). This is the application for creative cloud Manager.

  After that, I ran the new update and the problem is solved with an exception handler extention that update is still capable.

• Failure of USB ports after installing HP PSC 2510 wireless

  Just installed a HP PSC 2510 printer / scanner by using the wireless network on a Toshiba Satellite P10 using Windows XP Home SP2. After rebooting the system, all USB ports not recognized by any device. Assistance service HP told us to uninstall SP2 that we did, but still no USB.

  Have checked to see if all the USB drivers are on the computer and they are. Have uninstalled and reinstalled all USB drivers without success. Still no recognition for any device.
  Have checked to see if THE system BIOS is enabled - it is!
  Help! Any ideas?

  Hi sax,.

  First that I want to know y at - it problems with your HP printer. You can print all your documents? You use the printer for wireless data transfer or you make the USB connection?

  If I understand you right in Device Manager there is no problem, but you cannot use the USB Ports. What are the USB devices was not recognized?

• USB issues after installing Windows 7

  Hi guys,.
  Yesterday I upgraded my Vista 64-bit for Windows 7 64 bit PC. I did a clean and updated installation in the form of my readers in the process. Everything works fine except one thing.
  I bought a new audio interface for recording and playback of music. It's a Focusrite Scarlett 18i6. I installed all the software including updates since the Focusrite website and everything seems to be ok. I started to play music from itunes to test it and it worked well for a couple of minutes, then it disconnects just himself.
  It shows that it is connected in the Device Manager and the windows volume control panel. But it disconnects from the control panel of mixture of Scarlett and itunes stops playing because it no longer recognizes that there is an output device.
  The only way to let him play again is to unplug and plug back the power of the interface, and then it will work for a few minutes or a few seconds.
  I tried to update all my drivers in Device Manager. Unfortunately Acer does not all the drivers for my PC and windows 7. (Aspire X 1700).
  I have downloaded all Windows updates.
  I even tried to reinstall Windows 7.
  I'm trying this with nothing else installed on my pc is not a software conflict.
  I have an old XP computer, age about 6 years old and works like a slug, but it works with the interface very well. So I know that the problem doesn't lie with the interface.
  I saw somewhere that there is a known problem with USB drivers when using Windows 7, so I downloaded the patch, but it is said that it is not necessary on my PC.
  I'm very, very close to buying a new PC that I don't really want to do until I'm sure it's a problem with my PC which can not be repaired and that the same thing won't happen with a new Windows 7 pc.
  And Yes, my interface is compatible with Windows 7.
  Any help would be greatly appreciated as I have tried everything I can think.
  Thanks in advance.
  Emma

  Hello

  Hello
  You don't have to remove the keyboard and mouse USB. Try to reinstall the USB controllers. Visit the site of the manufacturer for the latest available drivers.
  http://support.Acer.com/us/en/product/default.aspx?tab=1
  As you mentioned that Acer has no drivers for Windows 7, you can install the drivers for the chipset in Vista compatibility mode and check.
  Make older programs in this version of Windows
  http://Windows.Microsoft.com/en-us/Windows7/make-older-programs-run-in-this-version-of-Windows

• System randomly crashes after installing the latest update of Windows 7

  I am operating Windows 7 OS on 64-bit pc. Since the automatic updates of Windows on 01/10/13, I experience a freeze randomly the system on a range of applications. I tried other updates and basic system maintenance tasks are completed, but the problem persists. Can you help me please?

  Hi Stuart,

  I see that the computer hangs at random after installing some updates. I'll help you with this problem.

  1. What is the brand and model of the computer?

  2. what security software is installed on the computer?

  3. which windows update has been installed recently?

  Let us try these steps and check the status.

  Method 1.

  Start the computer in safe mode with network and run a full scan of computer viruses.

  Advanced startup options (including safe mode): http://windows.microsoft.com/en-US/windows7/Advanced-startup-options-including-safe-mode

  Run a full scan of the computer with the Microsoft Safety Scanner to make sure that the computer is virus-free.

  Microsoft safety scanner: http://www.microsoft.com/security/scanner/en-us/default.aspx

   

  Warning of Security Scanner: there could be a loss of data while performing an analysis using the Microsoft safety scanner to eliminate viruses as appropriate.

  Method 2.

  Start the computer in a clean boot state, and check the status. A clean boot to test if any element of service or third party application startup is causing this issue.

   

  How to troubleshoot a problem by performing a boot in Windows Vista or in Windows 7 and Windows 8:http://support.microsoft.com/kb/929135

   

  Note: Once you have finished troubleshooting, follow step 3 in the article to start on normal startup.

  Method 3.

  I suggest that you can exercise SFC scan and check if that helps. The SFC/SCANNOW command analyzes all protected system files and replaces incorrect versions with appropriate Microsoft versions.

  For more information how to make SFC / scan, please follow this link: http://support.microsoft.com/kb/929833

  Respond with more information so that we can send us your request in an appropriate manner.

• His Dell Inspiron 1420, microphone and camera integrated into the laptop does not work after installing Windows 7 Professional

  No sound from my Dell Inspiron 1420 and the microphone and built-in laptop camera do not work after installing Windows 7 Professional 64-bit. My laptop has Windows 7 Vista 32 - bit family premium. My laptop is 64-bit capable and after going through the Upgrade Advisor, I installed Windows 7 64-bit. I can hear sounds when I use a headset plugged into the line-in Jack, but not through the speakers built into the laptop. I already tried new drivers from the Dell website, but I could not find.

  Any help will be much appreciated. Thank you.

  As it is has no drivers 64 bit Windows 7 on Dell Web site, your best chance is to install the 64-bit versions of Vista (if they exist) in compatibility mode, viz:

  Right click on the Vista driver, then select Properties > Compatibility tab. Now choose to run the program in Vista compatibility mode and then apply > OK. Right click on the file and select run as administrator to install it.

• My acquisition of data NOR usb-6008, does not appear in labview after installing drivers

  My DAQ does not appear in my labview program after installing the drivers. I can't add it to my program or anything like that. I installed 3 different drivers and updates, and it's still not appearing in labview. Is there something I'm missing or need to do yet?

  Thank you

  It seems that you have a damaged file somewhere in your installation.  You will need to go into the control panel and select the option to repair the installation.  You will need to run the repair twice due to a known problem.  After that, you need to reinstall the NI_Daqmx 9.4.

  Jacob K

• No usb 3.0 ssd fresh after install

  At 1 year, 8700, worked very well. Just do a fresh install with a 500 evo samsung ssd. I used the dell

  Reinstall the disc and disc drivers and utilities. Everything is ok, just no working usb 3. Ports works do not at all actually. I have install the 3.0 drivers but error message tried. Is there a problem with usb 3.0 and ssd? could use some help.thanks.

  Went to the view of dell drivers, to the down loaded the latest versions of the chipset drivers and usb 3.0 drivers.

  Woo hoo problem solved, thanks for the suggestion. Those on the cd were assumed to outmoded. Thank you

  to help everyone.

• PC Pavilion laptop: no sound on Pavilion g6 after installing the new battery CMOS

  I have a Pavilion g6z - 1 d 00 CTO Notebook PC, model A2F43AV number.  It came with Windows 7 Home Premium, and I upgraded the operating system to Windows 7 Pro (64 bit).

  The problem is that I did not sound, either through headphones or the speakers even if the Volume is set at 55. I first noticed the audio problem after replacing the CMOS battery, as the laptop is 4 years old and he gave me intermittent wireless connectivity problems.  After installing the new battery CMOS, I noticed the wireless driver was missing and downloaded/installed.  Everything was fine except the audio.  Then I reset the BIOS but nothing there as the BIOS version is v.49, and it is the most recent.

  I have also downloaded/installed the driver audio and rebooted the PC.  Still, there is no noise.

  Finally, I have checked the audio drivers and the reporting system they work without any problem.

  What should I do next?

  Thanks, Terry

  @Terry57

  Thanks for the reply,

  I was under the impression that these links would take you to guide step by step, however, it seems that they do not work,

  However, I have provided details below:

  To perform a hard reset on a computer equipped with a removable battery, follow these steps:

  1. Turn off the computer.

  2. Remove the computer from the docking station or port replicator.

  3. Disconnect all external devices from devices such as USB, external displays storage devices and printers.

  4. Disconnect the power adapter from the computer.

  5. Remove the battery from the compartment to batteries.

  6. Press and hold button power for about 15 seconds, remove any residual electric charge capacitors that protect memory.

  7. Insert the battery and plug the power adapter into the laptop, but do not connect peripheral devices.

  8. Press the power button to turn on the computer.

  9. If a boot menu appears, use the arrow keys to select start Windows normally and then press the Enter key.

  10. After you have reconnected each peripheral device, run Windows Update and HP Support Assistant to update all device drivers.

  To perform a hard reset on a computer equipped with a sealed or non-removable battery, follow these steps:

  1. Turn off the computer.

  2. Remove the computer from the docking station or port replicator.

  3. Disconnect all external devices from devices such as USB, external displays storage devices and printers.

  4. Disconnect the power adapter from the computer.

  To perform a system recovery, this link should work: click here

  Keep me posted for any technical assistance,

  Kind regards

• Computer OS used to start after installing windows 10

  Hello im having problem starting my system after installing windows 10. I did the install and it worked fine since the upgrade to 8.1. But then I tried to format the drive and in the menu format, he's stuck at 2%, and then I restarted the computer. Now it will hang at the hp logo and go back to the same logo. Do I have to replace my hard drive?

  What I understand, if you have completed the 10 Windows Installer and everything has happened until the end, then you are supposed to be able to do a clean install with the download of Windows 10 DVD or USB.  With a working computer, GO to THIS PAGEand scroll down to the button "download tool" selection the 64-bit version.  Once clicked, it will ask you if you want a DVD or USB for the iso.

  Once it's done and you have the DVD or the USB version, see if you can install Windows 10.  If this fails, you may need to replace the hard drive.

• 10 the desire: desire 10 cannot adjust the print size after installing new cartridge

  After installing the new print cartridge (60XL) print size is very large: so far, I have unplugged the usb connection and power, reinstalled the cartridge a few times and run tests... I also went to control panel and looked at all the parameters, but find no way to adjust the size of printing... can anyone offer a solution... Thank you

  the solution: problem was with Firefox, when I switched to Chrome it prints perfectly!

• G6 notebook pc Pavilion: Hello, I tried to create a bootable USB key to install Windows XP. WH

  Hello
  
  I tried to create a bootable USB key to install Windows XP. When I tried to copy my files to osi XP USB tool of Flashtoboot my laptop suddenly stopped working with some messages of the blue screen and hit up with a screen that is black with the letter 'J '.
  
  I restarted my laptop using the power button, but all the time, I get a black screen with the letter 'J '. When I tried Ctrl + Alt + Del screen will blink for some time and time again I get the same black screen
  
  By pressing the F1 key, I did the test of memory RAM and hard drive memory. Both tests passed successfully. I tried starting the screen remains black local disk.
  
  Product: Model LAPTOP computer: laptop HP pavilion g6
  Product number: QG470PA #ACJ
  
  OS: Windows 7
  
  Thank U
  Look: -.
  EDWARD07Hello,
  
  I tried to create a bootable USB key to install Windows XP. When I tried to copy my files to osi XP USB tool of Flashtoboot my laptop suddenly stopped working with some messages of the blue screen and hit up with a screen that is black with the letter 'J '.
  
  I restarted my laptop using the power button, but all the time, I get a black screen with the letter 'J '. When I tried Ctrl + Alt + Del screen will blink for some time and time again I get the same black screen
  
  By pressing the F1 key, I did the test of memory RAM and hard drive memory. Both tests passed successfully. I tried starting the screen remains black local disk.
  
  Product: Model LAPTOP computer: laptop HP pavilion g6
  Product number: QG470PA #ACJ
  
  OS: Windows 7
  
  Thank U
  Look: -.
  EDWARD07

  EDWARD07

  Hello;
  
  Let me welcome you on the HP forums!
  
  According to your description, my guess is that the program that you used has replaced the boot files on the hard drive, NOT on the flash drive. Thus, your PC no longer starts.

  To resolve startup problems, you need access to a PC for this phase of work in order to create the necessary support to fix your PC boot loader.
  
  You will need to create something called a CD-ROM to repair Win7 - which you could have done for free when Win7 was working.  This will repair the boot loader files, and if that is the problem, your PC will start OK after that.
  
  But now, which can be obtained (with supplement) from this link: http://neosmart.net/blog/2009/windows-7-system-repair-discs/
  
  When you download this file, it will be an ISO file.
  
  To make a CD bootable it, you will need to download and install ImgBurn: http://www.imgburn.com/
  
  Once you have installed, run, select the option "Save image to disk file" and select the downloaded ISO file and that it points to a blank CD.
  
  To make a USB bootable of it, you will need to download and install RUFUS: https://rufus.akeo.ie/
  
  Once you have that, it is executed in the input of the unit, use the drop down menu to select the USB stick.  Near the bottom right, where is written 'Create a bootdisk to aid', select the ISO file downloaded.
  -------------------------------------
  
  Boot from the media that you have created and follow the instructions in this link: http://www.sevenforums.com/tutorials/681-startup-repair.html
  
  You will probably need to run Startup Repair three times for him to fix all the boot loader.
  
  Once completed, your PC should start OK.

  Good luck

• After installing new FN and multimedia keys do not work on Qosmio F20

  Hello, my friend buy Qosmio F20 of the Germany, but it comes with Windows Xp with the German language on this subject. I format the hard drive and install Windows Xp Professional SP2. I download all of the drivers who was very available and most of the functions work (like display, sound, touchpad and others), but the multimedia keys and the FN keys do not work (remote work). The other problem is that I can't install the TV tuner.

  With German Windows XP, I try TV tuner but have no SOUND what is the problem? When I try to install the utility software under display appear message that says "Unable to get the information from the BIOS" or something comparable. I have install all the drivers that I found in the Qosmio F20 support page but I have video control with exclamation mark in Device Manager.

  Can you help me?

  Where am I wrong? What should I do?

  First of all he must know that if you are going to install together the Toshiba drivers after installing the OS to do in the right order!
  On the Toshiba driver page, you will find the Installation Instructions. You will need to follow the guide line! It is important to properly work all the functions!

  In addition, you will need to select the right OS. There are two: XP and XP MCE.

  To control buttons Toshiba works correctly, you will need to install the controls.
  But as I said above: follow the instructions in the insulation.

  A few words on the TV tuner:
  As far as I know, you can only use the TV tuner in the country where the laptop was purchased because different PAN and NTSC settings.
  In addition, the TV tuner driver offers TV tuning and recording capabilities using Media Center on your computer. If you have any MCE so I put t know how you want to watch TV.