USC fails to load after firmware upgrade on PET310

Similar Questions

• Windows fails to load after installing an update

  Installed cumulative KB972260 for IE7 for Windows Vista security update this morning on my laptop Dell running Vista Home Premium 64-bit.  After installation choose reboot and the computer fails to load up.  Changed the restore point to the last use of the 22/07/09 and still have the same problem.  When checking why it breaks down I got a verification of the System Restore Failed error 0 x 490 and also system file integrity check and repair does not = 0 error code x 490.

  I am at a loss?

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
  If the above fails, try this:

  As is the case with most computers/laptops these days, they do not come with good Vista disc to repair only the recovery disks.

  As your grave in the category above, download the ISO on the provided link and do a repair of the disc.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  You can make a tool to restart system, System Restore, etc. with it.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista repair disc.

  You can do a system restart tool, system, etc it restore.

  There is not a disk of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  See you soon.

  Mick Murphy - Microsoft partner

• M1212nf fails to boot after firmware update

  The full printer name is LaserJet M1212nf MFP.

  I was installing the complete package driver, not the minimal driver file, on a new system of Windows8 is the only wireless. The printer itself has a wired connection to the switch.  He was already working for a Windows Vista, Windows 7 and Linux systems.

  During installation, it attempted to load the firmware - I don't know if it has been completed or not.  Now, the printer does not really work.

  Since then, even after several cycles of power > 30 seconds, the printer continues to repeat the message "initialization".... ' without ever coming to the ready state.

  I tried to reload firmware, this time by the Windows 7 laptop via a usb cable, but it does not appear to be able to connect.

  This printer is watered constantly, or is it possible to reload the firmware in new since I assume that the currently loaded or partially loaded firmware is the problem.

  Thank you.

  Hello world

  If you've posted on the forums about this, you will find I recently sent a private message to each of you, and has nothing to do with more troubleshooting. If you have not already posted on the forum about this, please reply to this topic to let me know that you have problems.

  Please see the update private message send you in the last two weeks. I would like to hear from each and every one of you who received a private message from me in order for me to solve this problem. Please let me know if you have any questions.

  In private messages sent, I ask you to contact you by phone or email. This information is private and should not be given the open forum pages. Please visit the private message that I sent you in order for me help solve the issue. This has nothing to do with in warranty or out of warranty that everyone on this thread has got the same message private that you got me. Please get back to me as soon as possible.

• Jump and mix tracks after firmware upgrade?

  I can't explain it. Since the latest firmware upgrade Fuze my wife started jumping titles (for example jump to the next song to halfway through the current), but a funniest part - he mixes parts of files. We can listen to a song, and then all of a sudden he would be interrupted by 1 second of a file from a different album and then come back to play the first song from the point it was interrupted. What gives?

  Me that was too much.  I downloaded all my music back and reset my Fuze and reformatted it.

  Charge of excessive songs and back on went.

• Flexflash controller is in a lamentable state after firmware upgrade

  Hello everyone

  I get an error message indicating that our flexflash is unhealthy after firmware update.  Say it running old firmware.  I didn't even know that us had flexflash on our systems and do not now see update the firmware.  I read that you are supposed to see in the storage tab, but do not see.  How to solve this error?

  I came across the same thing after the 2.2 2.2(5a) (3rd).

  Everything was fine, but who. He was a minor.

  Was the only thing I could do about it, decom the blade, take it out, put back in, re - ack the server. Then he went away.

  (We use the FlexFlash and it caused no problems before or after the warning). You can try to reset the FlexFlash controller, but I don't think that will work for this particular minor warning.

• Satellite Pro A120 fails to load after upgrade BIOS and XP to Vista

  Help

  I have problems to make my laptop to load the Windows operating system. My laptop (no X6062917H series) was purchased in November 2006. I've recently upgraded the operating system to Windows Vista (Toshiba, Promotion) and was later to upgrade the BIOS of Toshiba.

  This was done via the Toshiba site, opting for the upgrade via the Windows option. Since the upgrade of the BIOS, I have used this phone two or three times, and now I can't use it at all.

  When I turn on the laptop now, all I have is a white screen with the arrow cursor. The cursor moves on the screen that I have spend my finger on the touchpad.

  I welcome any advice on getting my laptop to the top and running, my computer knowledge is limited, please make sure it is as easy as possible

  Thank you very much

  Mr. Gibbs

  It seems that you are using the Satellite Pro A120, which belongs to the series of PSAC1E.

  It seems that the laptop can boot the operating system because the arrow cursor appears on the screen.

  Have you tried to connect the laptop to the external monitor to check if you can switch the display to another monitor?
  It would be very interesting to know if it s a graphics card problem or the internal display problem

  If you will not be able to see something on the second monitor, I recommend trying to reinstall the operating system.
  But if it is not possible to reinstall the operating system, you will need to contact the ASP (provider) in your country for the control of the laptop.

  Good luck

• WRT310N no admin after firmware upgrade is

  I went from 1.06 to 1.09 and the router works, all devices, including wireless are able to access the internet.

  However, I can access is the GUI.   Before the admin access upgrade was configured to use HTTPS only.   After updating Firefox and Internet Explore give a warning of the cert.  If you 'ok' after he tries to display basic settings page (the title of the page shows the basic settings), but the page loading hangs before anything be it appears.

  If I close the browser and try to try again it will fail altogether.  If I reboot the router as described above will happen once, then another reboot is necessary.

  Any thoughts on what I might try to get it working again?

  Thank you

  You upgrade the firmware on the router, I suggest you to reset the router for 30-35 seconds. Cycle power to the router and check.

• Extension stopped working after firmware upgrade WN2000RPTv3

  I updated my firmware to wn2000rptv3 - V1.0.1.4.

  Now, my range extender only goes to a page in the account registration.

  Nothing I try (mywifiext.net, http://www.routerlogin.netor .com) helped him.

  While I didn't create an account, I tried to anyway.

  After you have filled all fields, the next button stayed grayed.

  It didn't matter how many times I've tried, it's always the same.

  I tried with passwords symbol 12 and 15. No luck.

  Now, my extender is basically useless unless someone can tell me how to solve this problem.

  The Extender worked like a champ before the upgrade.

  Just goes to show that newer isn't always better.

  Any suggestion is appreciated.

  Thank you.

  Thanks for the reply DarrenM.

  I followed the instructions but it will not be upgraded. I tried several times.

  Finally, I rebooted the computer and retried all on and VOILA, it worked like a charm.

  I even braved upward and updated again and it took the update of firmware as a champion.

  Don't know what I did wrong on the first upgrade.

  Don't know what tomorrow will bring, but tonight, I'm a happy camper.

  Thank you very much!!!

  SM

• Can't go forward or backward in the chapters of the audiobook, after Firmware upgrade

  I have improved my rocket to the 2.03.33 version of the Firmware and now I am unable to go forward or backward in the chapters of the Audiobook. I have done this before to upgrade. Please advise thanks.

  Here is a link to 2.03.31 if you want to try a downgrade.

  mp3support.SanDisk.com/firmware/fuze/fuze02.03.31.zip

  mp3support.SanDisk.com/firmware/fuze/fuze02.02.28.zip

  You can see how this link is built, then you can also try its replacement by other version numbers - 2.02.2 x (X for everything you want to try) - to find other versions.

  Download the file, unzip it, drag FuzeA.bin to the drive letter for the "rocket".

• Ergonomics of Linux lost after Firmware upgrade

  I use my rocket for some time, with no major problems, using Ubuntu. But recently I've updated the firmware to V01.02.28 (using Windows) and now every time I connect Ubuntu the thing crashes with a message 'written', and I am unable to mount. I tried downgrading to the V01.02.26 and I still have this problem. I noticed that the splash screen has not changed at the time where decommissioning, so maybe I was using an even older version.

  You may have already checked however double check settings USB drive... after the update of the firmware, I noticed mine has been switched back to automatic detection by default.

  As side note... you are not alone in what concerns the Assembly of the "rocket" under Ubuntu.More often not I need to disconnect/reconnect the device before it is mounted. Although often it will not mount even if lsusb detect. Restart often solves things.

• Wmb54g doesn't work after firmware upgrade?

  I have a wmb54g wireless music bridge. I just upgraded my Gigabit Wireless-N router. (WRT310N) My bridge worked OK, so I've updated the firmware this morning. Since then, my network will not recognize the WMB54G. I have reset the unit several times and spent 2 hours chatting online with Linksys. It still does not.

  I uninstalled the software bridge. I hung the bridge directly to my router, but still not my network will not see it.

  I tried to access the bridge directly by 192.168.1.210, cannot do?

  Update: bad news, cannot ping bridge when it is connected directly to the router. Linksys will send a replacement WMB.

• Cannot access the WAP54G after firmware upgrade

  I have updated the firmware of my WAP54G v.2; We just started to use the AP again and when I checked, I thought I would update. I was going to 1.2 or 1.4 to the latest firmware using this link http://homesupport.cisco.com/en-us/wireless/lbc/WAP54G, version 2. I could see the AP before starting my Dlink router. I downloaded the firmware and the upgrade of the access point. She completed successfully, but when I tried it I could reach him is no longer. I checked the router and it shows is no longer there and I can't access it via the installer.

  How you try to access the router configuration page? If the access point is connected to your d-link router, make sure that your router's default ip address and AP are in the same range. The IP default WAP54G is 192.168.1.245.

  If the router's default IP address is different, so you will need the AP wired to your computer and assign a static ip address to your computer ie: 192.168.1.10 and then connect to the access point configuration page and settings wireless entry and change the default IP of AP, which is of the order of your d-link router.

• ERRO 'bad gateway entered' after firmware upgrade BEFSR41

  I have updated the firmware on my router Linksys BEFSR41 V4.3. On this router I used Statis IP (if DHCP active). It worked well on my network, until this upgrade. Now when I try to ad another static IP address, or when I want to change something in the Routing tab, I get this message " bad gateway entry! It should be the same WAN IP subnet "." Strange because I have not changed anything in the settings.
  I did a full reset on the router, still the same problem.

  Any suggestions?

  Enable the DHCP server on the BEF. That's all. There is no need of any static routes in this configuration.

  If you enable the DHCP server, either change these static IP 192.168.1.100 etc. for addresses outside the server DHCP address pool (default 192.168.1.100 - 149) or adjust the DHCP server address pool, for example to change IP address of 192.168.1.100 DHCP start 192.168.1.10 or 192.168.1.200 or whatever you want. The important thing is that static IP addresses are not inside the DHCP server address pool.

• Cannot print or scan from MacBook Pro to Officejet 6500 E709n after Firmware upgrade

  I have-

  MacBook Pro; OS X 10.5.8

  JO HP 6500 E709n: Firmware RBP1FN0935AR connected by Ethernet to my network.

  Also several XP and Vista machines machine.

  I have most of my printing and scanning of MBP.  I've updated the firmware the week last version (above) found under the XP software and drivers for this printer.  I thought more recent firmware is always better.  In any case, after that, I can no longer print or scan from the MBP.  I've uninstalled and reinstalled the software on my MBP 2 times.  And I followed the instructions on this forum for posts with similar problems.

  I can see the printer in the Systerm preferences > Print & Fax.  He is registered and has a green light.  I can navigate to the printer and connect.  I can not state of ink.

  BUT when I run the Setup Wizard, the printer is not listed in the window "select the device".

  When I do 'add devices by IP' and enter the IP, I get a message saying that it could not connect to the printer.

  I can print from my XP and Vista machines.  The XP machine is a virtual machine on VMWare Fusion on my MBP.  So I now transfer that I want to print my XP VM just to print it.  Is NOT IDEAL, but that market.  Hoping to solve this problem.

  1. I try to downgrade the firmware to the previous version.  Is anyway to do this?  How can I get the previous version of firmware?

  2. I would like to know what ports are used to connect to the printer?  If anyone can let me know, I'll see if my MBP has those blocked or not.

  3. If anyone can offer a solution, I would appreciated it.

  OK, I finally found this thing.  What happened was that my wireless connection does not (for reasons unknown at this point) my Mac to connect to the printer.  Even if I can get to the Web page.  Hello may not cross.

  Anyway, on a whim, I disabled the airport and used an ethernet cable to connect to the same switch the 6500 was conducting and reinstalled the software.  And whaddaya know.  I was able to install the printer, then did a scan and printing and a jig around the room.

  I disconnected the cable and turn on the wireless connection, once again, and wouldn't you know, HP Scan Pro can not connect to the 6500.  Is returned to the thread and it works.  Hmmm.

  I am due for an in new wireless access point.  The DLink and my Verizon FIOS Actiontec router sometimes do strange things.

  I'll still give you, PrintDoc, 1 kudo for loans to help.  And the uninstalling of 3 keys; It was new to me.

  I may be the only one who has never fallen on this, but it may be useful to say, do NOT take your connection Wireless for granted.  Always test everything.

  Thank you

• CS5 fails to load after reformat HD?

  Own CS3 and CS5, CS3 loaded OK but claims CS5 serial number is not valid.  Has been loaded on the same HP workstation and only try to reload to rebuild after a clean reinstall.

  The strange thing is that CS3 load, my a/c Adobe shows no CS3 as it was bought a long time ago, but the a/c lists CS5 which will not load.

  Belonging to these two programs again, can not find a phone number or address of the ODM support Adobe email.

  Any help please?

  Please check: error "serial number is not valid for this product". Creative Suite