Users randomly requested to restart when they connect

Similar Questions

• Control what dashboad a user sees when they connect

  Hello

  I'm running vRops 6.1 and users are imported from an LDAP source.

  I would like to configure the dashboard of the user, i.e. when they connect see and access to a single specific dashboard.

  any ideas/help?

  Thanks - Dan

  Hi Dan,.

  You can create the user dashboard, then share it with one or more groups of users. When you share a dashboard, it becomes available to all users in the user group you select. The dashboard will appear the same for all the users who share it. If you change a shared dashboard, the dashboard changes for all users. Other users can only view a shared dashboard. They cannot change.

• I need help showing an email to users when they connect. Any help would be appreciated!

  Hello

  Now that I'm able to view username someones after they connect by using the code below, how in the world do a page to show their email. For example, when they change their e-mail addresses in the settings said beside the form "your current e-mail address is defined as...". "How do I show?

  Code user name:

  <? PHP echo $_SESSION ['MM_Username'];? >

  It's like in all this?

  Thanks for any help.

  Well, if yes then u just pull the email from the recordset variable. To make the Recordset, go to server behaviors > recordset. The field filter, choose the user name > session variable > MM_Username. Then, towards the face u can see "Bindings", click it and click on the recordset that you did before you see all the variables in this Recordset (click more +). Then you just have to drag this e-mail on your page variable. It's done!

• Satellite A300 restarts when I connect AC adapter / CC

  I have Toshiba Satellite A300, and there is problem, as soon as I connect my adapter to my labtob it restarts directry, and there is no problem when I connect my adapter for my labtob in offline or even in safe mode.
  I tried to update the BIOS but I can't caudln because it is difficult to udate BIOS without plugging your power adapter...

  something else, I changed my power adapter with another, but nothing has changed and I corrected my original vista OS labtob, but also nothing has changed

  can any body help my out to solve this problem

  awaiting your response

  With or without the battery, the laptop must run stable on the sector
  If it s not the case, it is possible that your motherboard is affected but I hope that's not because it would be the worst case :(

• We have laptops in the field who use VPN to connect. How can I get these systems to update our DNS when they connect to the VPN?

  Our mobile sales are part of a domain but not connected to our network. Cached credentials are used to connect outside the office. Once they connect and view their desktops, they select the card from Verizon and use it to connect to our network via a VPN connection. These generally to enter an IP address but the router that connects and not from our DHCP server. This usually means that updates to our DNS servers are not always instantaneous (or update at all).

  When they are done for the day, they just closed the lid of the laptop and he starts in mode 'sleep'. The next day, they open the lid and no lgin is necessary, but they do not need to reconnect to the VPN through their cards from Verizon.  How can I configure my DNS to update more frequently or maybe these computers portable bécon a command "ipconfig/registerdns"?

  We have to connect to these systems in the field and it is almost impossible, unless we call the sales person and ask them their IP. We have more than 350 laptops in the field, then this makes it almost impossible to update all the.

  Hello

  Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for Windows XP on Technet. Please post your question in the Technet forums. You can follow the link to your question:

  http://social.technet.Microsoft.com/forums/en-us/itproxpsp/threads

• How to allow the user return to give lectures when they take a quiz?

  Hello world
  
  I'm new to Captivate and now I'm kinda in a dilemma. Thank you for your
  time to look at my post!
  
  I created a CBL in Captivate 3, the first 10 slides is a conference and he
  is followed by a quiz of 10 slides, defined as standard SCORM.
  
  I want that the learner must be able to refer to the Conference when they
  Take the quiz, I tried 2 approaches and they both
  issues in different ways.
  
  Approach 1: "allow moving backwards" and "infinite attempts. The
  problem with this approach is when the learner clicks on "review the.
  quiz"and when they click"back"on the first slide of questionnaire, all
  Quiz will start everywhere, the score is reset to zero.
  Because the quiz is seeing this as a new attempt and that the learner is
  permit to make "infinite attempts" such that it has been configured.
  
  Approach 2: "Allow moving backwards" and leave only "1 attempt.
  The problem with this approach is, when the learner is in the Middle
  Quiz and refers to the Conference, the quiz will be
  automatically shown as completed. And the learner will not get a
  chance to answer these questions unanswered.
  
  It seems that every time that I leave the learner refer to the Conference
  in the middle of a quiz, the quiz will be seen as completed. Who am
  I did wrong? Is there a better approach I can "allow backward
  movement' and always allow resumes user their quiz where they have left
  in the distance?
  
  Sorry for the long post, I was not able to express it in a more
  concisely.
  
  Any help is really appreciated!
  
  -David

  What you see is the behavior designed as in Captivate for the quiz.

  Each Captivate movie has a range of "quiz", which starts with the first measurable purpose and ends at the Quiz results slide.  If you enter the scope of quiz by starting a slide of questionnaire, then jump back away from quiz, to return to the basics, default behavior of Captivate is to freeze the quiz at this time here.  Then when Captivate refers to allow movement to the rear, it is talking only a move backward in the quiz.

  For example, if you get to question 1, but no answer and proceed to question 2 answer that we can go back to question 1, you will still be able to answer question 1.  The test will not be frozen.  However, if you had jumped to any slide before question 1, your quiz would have been frozen with everything that you mark had accumulated at this time here.

  There may be a workaround that you can use to get closer to what you want.  As any object that is classified as part of the quiz, you can add a button on one of the first slides that the user must click to move forward.  Set the properties of this button (or click on the box) to report a score for the quiz.  What makes a part of the scope of quiz.  Now, any content slides falling after this slide button are also within easy reach of quiz and return to them will not have the same effect of freezing the quiz.

  Please keep in mind another aspect of the quiz questions: If you answer a quiz question, and then move off the slide (forward or back) quiz question answer is frozen and cannot be modified unless resume you the Quiz or raise all of the module.

  Hope this helps to clear up how things work.

• With several Secure areas, how can you check that the user box is subscribed to when they are connected?

  So I guess it has to do with {module_data} and your API but I can't seem to understand this.

  I have 3 secure areas, basic, premium and pro and I want to use the liquid to display content on their page of account based on what secure area, they are advertised to. I know how to write the logic of the liquid, I feel like a dunce because I don't know which module to use to check where they are subscribers. Please when replying, don't slam me too hard upside the head because I don't know that it's right in front of me.

  I thank everyone!

  You can use module_data to get the information, but you still had the native module to do this:
  module_subscriptions | Developers of business catalyst

  You can run a collection and do what you want with the data.

• I have upgraded to windows xp pro and when I downloaded the sp2 computer freezes and restarts when I connect to internet

  I have upgraded to windows xp pro did all updates, and when he places classified sp2 it restarts fine then when I loged on more updates to update it freezes and reboots, when she will recover no codes or anything be it what could be the problem...

  Hello

  1 is it only during the use of the internet?

  Method 1.
  a. click on start and then right-click my computer.
  b. click Properties.
  c. click on the Advanced tab and then click settings under Startup and recovery.
  d. under system failure, click to clear automatically restart it the box.
  e. click OK, and then click OK.
  f. try to reproduce the error message.

  
  Method 2.
  Check to see if the problem exists in Safe Mode, if the computer works as expected in mode without failure, then we can solve the problem in the clean boot state.
  a. refer to the article below for the procedure safe mode in Windows XP
  A description of the options to start in Windows XP Mode
  http://support.Microsoft.com/kb/315222

  b. you need to perform a clean boot to find the program that is causing and then disable or remove.
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353/en-us
  Note: When you are finished troubleshooting, follow the steps as explained in the article to reset the computer to start as usual.

  Also I would ask you to update all the drivers of material from the manufacturer's Web site.

  I hope this helps.

• I can't get my top AP Express extend my AP Extreme wifi when they connect through an ethernet cable.

  I have an extreme AP as my main wireless and router. At the other end of the House, I have an AP Express that I used to extend wireless network. It works, but slows down the network. I have now an Ethernet cable between the extreme LAN port to the WAN Express port so I can more effectively extend the Wio - Fi. When I try to put in place, I am never successful.  I get a variety of error messages. I use Windows 10 to run the airport utility. I got it finally return to work as a wireless extension after the reset of the Express to the factory setting.  Thanks in advance for the advice.

  We can provide you with all the manual settings that you will need, but things would be a lot faster and a lot easier if you have an iPhone or an iPad that is very convenient to set up the AirPort Express.

  We assume that the two airports are 802.11n devices or later and you have tested the Ethernet cable to ensure that it works correctly.

• members of the team get tiralversion when they connect the first time, after nog activation trial period is possible, they showed in the team, with good ID but adobe refuses to acknowledge the affiliation. Adobe support is the worst ever seen, some Indian

  How I can activate

  Hello

  I apologize for the frustrating experience.

  Don't you see State of the team member of the license as 'Active' on the admin console?

  Please visit: https://helpx.adobe.com/creative-cloud/help/manage-teams-membership.html

  Kind regards

  Sheena

• software installed as that user admin does not work when logged in as standard user

  Running a desktop computer dell with XP SP3 home edition with no possibility of wifi

  Bought the USB adapter wireless and successfully installed the software and connected to the router connected as a user with administrator rights. When I connect software standard user being their but does not connect to the router. ? Standard user family security enabled, I disables it, but it makes no difference.

  Thanks for your suggestion, yes tried and it works when I connect as long as the user admin with a password even if I'm in the standard account. However he does not remember the settings, so whenever you access the standard account you must connect as admin users that would amount to giving the password to the admin of my grandson who defeats the object to have its own user account.

  But I solved the problem, when I looked in C:\documents and setting\admin data User, I found the folder for the software with an ini configuration file and a profile ini file. The profile ini file was missing in the same application for standard user folder. When I copied the file across and made a minor change to the standard user configuration ini file is the file of users admin everything works fine

• We have no admin on Windows 7 users. They change the homepage and it works for this session. When they close the browser and restart again the default home page is displayed.

  Windows 7 Sp3. using Firefox 7.01
  Non admin users.
  Home page change to what they want and it can work.
  BUT when they close firefox and open it again the home page goes back to the default setting

  You have a (security) installed software that can restore files when starting?

  See:

  • http://KB.mozillazine.org/Preferences_not_saved
  • https://support.Mozilla.com/kb/preferences+are+not+saved

• Windows Server 2012 R2 Remote Desktop Server - user session crashes when you connect to the wide

  From time to time, a user session hangs during registration out of the Windows 2012 RDS.

  This has happened for two different users. Whenever the session hangs with the message "signature" and the user can not log such as they appear with the same message by.

  I connected to the RDS as administrator, checked the Task Manager and found that an office application always work, such as Excel.

  When I complete the process of the office application and disconnect the user through the Task Manager, the user can log in again.

  I reinstalled the desktop software and still happens from time to time...

  Any suggestions?

  This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)
  *
  http://social.technet.Microsoft.com/forums/en-us/home s/fr-U.S./Accueil
  http://social.msdn.Microsoft.com/Forum

• Hi, I have a toshiba tecra 5000 I downloaded updates when they try the third phase of the update download the computer stops and restarts.

  I'm a newbie with this stuff so bear with me.  I updated charges, when they get to the third stage of the download the computer stops and restarts. I tried all types of restart, the system is unable to connect. now the hard drive light on the face of the computer won't lite, the laptop won't even consider itself restart any ideas

  Hello

  1. the updates you downloaded?

  2 a successful installation of updates?

   

  Follow these methods and check

   

  Method 1:  If you are still not able to start the desktop computer, you can rename pending.xml and check.
  Renaming or removing the pending.xml file booting from the Windows Vista disc.
  a. Insert the installation disc.
  b. restart your computer.
  c.Press any key to load the disc.

  Note: If your computer is not configured to start from a CD or a DVD, see the documentation provided with your computer. You may need to change your computer's BIOS settings.
  d. choose your language settings, and then click Next.
  e. in the System Recovery Options menu, click command prompt
  f. at a command prompt, type the following command below and press ENTER
  CD C:\windows\winsxs

  g. now, type ren pending.xml pending.old , and then press ENTER.
  Restart the computer and check.
   
   
  Method 2:  Once you are able to boot to the desktop, follow this method.
  An update is not installed successfully when you try to install the update in Windows Vista and Windows 7:
  http://support.Microsoft.com/kb/949358
   
   
   
  Thank you

• slow when they are connected via anyconnect VPN, ASA OS 9.0

  Hi guys

  My users are complaining that they are experience slowness when they are connected via vpn anyconnect for ASA os 9.x, 5 Mb files tikes 15 mts rough with them, even if these users also have a connection broadband on their place

  any guy insight

  Thank you

  Hi Ibrahim.

  My first suggestion to you is to follow the recommendations of Cisco, associated with latency problems.

  hostname (config) #-group attributes policy
  hostname (config-Group-Policy) #webvpn
  hostname (config-group-webvpn) select #svc dtls
  hostname (config-group-webvpn) #svc df-bit-ignore enable
  hostname (config-group-webvpn) #svc routing-filtering-ignore enable
  hostname (config-group-webvpn) mtu #svc 1200
  hostname (config-group-webvpn) #svc compression no

  (a more recent version, you can use the command "anyconnect" instead of "svc")

  If after this the problem persists please let me know when is the right time to reproduce the problem and collect the balls, debugs and catches. I also need the current configuration of the SAA (see technology in a txt file)

  Kind regards

  Aditya

  Please evaluate the useful messages.