Venue 11 5130 Pro 32-bit to 64-bit

Similar Questions

• Dell 11 place 5130 pro 32 bit flickering screen brightness

  Hello

  Device is manufacure renovated like new they say looks like new, software was etc reset factory

  the first system startup

  I do experience flickering BOUNCING hard if I try to adjust the brightness no matter where less than 100%, sometimes the slide has no effect but after 10 to 20 seconds, the screen starts to Flash, sometimes the brightness drops lower and starts to blink... low to Hi power very quickly.

  Adaptive brightness is off everywhere

  Cooling - off Panel

  Energy saving - off

  Even in the Bios when I change the brightness level, it starts to Flash.

  Everything is up-to-date.

  Any suggestions?

  Found was a hardware problem

• Aurora running, but can not be played on Desktop Windows 7 pro 64-bit

  I've been using Aurora for several years with Windows 7 pro 64-bit with the two latest major 28/29 Auroa just missing from my desk after clicking on the icon on the desktop, I tried to uninstall, but the system told me I had still Aroura running uninstall so I had to reboot my PC, I could uninstall I then reinstalled Aurora and a pinned icon appeared in the taskbar, but when I clicked on the icon on the desktop the hourglass turned but no Aroura started on the desktop, so I went through the whole thing again and uninstalled Aurora and installed Firefox V26 and now it has progressed to the last version that has disappeared as exactly the same way.

  What can I do if I use Aroura again because it is very good and safe to use?

  I can't use the troubleshooting info as I can't see Aurora/Firefox to view or copy/paste the info shown.

  Pete

  Thank you solved the problem, I restarted the PC and now Aurora works again thanks.

• Unsupported personality: PCL on print Laserjet 1012 from Windows 7 Pro 64-bit

  I have an HP Laserjet 1012.  My PC has Windows 7 Pro 64 bit.  I used the Laserjet 1015 PCL 6 drivers.  When I printed the first two times, it worked fine.  Now each page just print "Unsupported personality: PCL ' at the top.

  What should I do now?

  Thank you for your ' Experts for a day Tech Support.

  Mark

  Hi rbarbo43,

  I found the following thread that will help you during the installation of the printer in Windows 7. Let me know if you need assistance?

  http://h30434.www3.HP.com/T5/printer-networking-and-wireless/LaserJet-1012-driver-for-Windows-7/m-p/351356#M16114

• Portege z30-b-14z 10 Pro 64 bit will not be in hibernation

  Dear all,

  My new Portege z30-b-14z 10 Pro 64 bit will not be in hibernation.

  I can not hibernate through the following methods:
  1. click on 'Start', 'power', 'Hibernate '.
  2. press x and windows, click on 'Close or disconnect', click on 'standby '.
  3 a prompt as administrator and type "powercfg/h on" and then press ENTER to activate the Hibernate mode, then type "shutdown/h/t 0".

  Yet once, nothing works. I want to really just close the lid of my laptop and have hibernate.

  Well want to can someone help?

  See you soon,.
  Bender22

  Dear all,

  There has been no response. This is my 2nd Portege for work and I can't go to the Hibernate in Windows or Ubuntu. What gives? I have this job and must close and run meetings with out having to stop and shut down all my programs that I have running. I need this laptop to Hibernate.

  I also have a DynaBook (of Japan) and the R830 running current House to run Win 7 64 - bit professional. They cannot Hibernate or the other.

  Can anyone help, because Toshiba cannot.

  See you soon,.
  Bender22

• Webcam not found by SKYPE running in a mobile HP6555b running W10 pro 64-bit

  SKYPE ran fine under W7 pro 64-bit, but now that I've updated to W10 pro 64-bit SKYPE does not see the built-in webcam. The Device Manager shows the webcam under States that it works correctly and imaging devices. What should I do to make SKYPE see.

  I went there where you said to go and download the driver package. I ran it and dxdiag and he is still also display ageneric. I'm sorry to say that SKYPE and W10 do not play well together and W10 seems to be still in version beta with all people who apply the upgrade. I give up and return to W7 where everything worked well.

  Thank you for your efforts to try to solve my problem, but the compatibility between the software and the operating system and the hardware is just not there with W10.

• iTunes, sync to Crash with Seven Pro 64-bit

  Hello

  iTunes Crash with this error message when I try to sync my iPhone 6 on my PC with 7 Pro 64-bit

  Problem event name: APPCRASH

  Application name: iTunes.exe

  Application version: 12.3.2.35

  Application timestamp: 56689eb6

  The default module name: CoreFoundation.dll

  Version of the default module: 1.750.32.0

  The default module timestamp: 55dd4433

  Exception code: c0000005

  Exception offset: 0009f63a

  The system version: 6.1.7601.2.1.0.256.1

  Locale identifier: 1036

  Information extra No. 1: 0a9e

  Information extra No. 2: 0a9e372d3b4ad19135b953a78882e789

  Information extra No. 3: 0a9e

  Information extra No. 4: 0a9e372d3b4ad19135b953a78882e789

  Read our privacy statement online:

  http://go.Microsoft.com/fwlink/?LinkId=104288 & clcid = 0x040c

  If the online privacy statement is not available, connection out of the version:

  C:\Windows\system32\fr-FR\erofflps.txt

  Can you help me solve this problem?

  Thank you

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  Error sharing a trend similar to that in the third box, so a similar approach should work. Looking for CoreFoundation.dll in:

  • C:\Program Files\Fichiers Files\Apple\Apple Application Support or
  • C:\Program Files (x 86) \Common Files\Apple\Apple Application Support

  Delete if found, then repair Apple Application Support.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach. Review the other boxes and the list of documents to support more far down page in case one of them applies.

  Your library must be affected by these measures but there are backup and restore advice elsewhere in the tip of the user.

  TT2

• Satellite L550 PSLW8A can only get OEM Win7 Pro 32-bit to 64-bit?

  Hi all

  I am writing from Australia.

  Two weeks ago, I bought a new laptop Toshiba ([http://tinyurl.com/ye6jkuq]) with the following characteristics:

  Model: Satellite L550
  Reference number: PSLW8A-01101F
  BIOS: V1.60
  CPU: Intel Core 2 Duo CPU P7450 2.13 GHz
  RAM: 4 GB
  HARD DRIVE: 500 GB
  OS: Windows 7 Professional 32-bit (OEM preinstalled)

  My question:
  How can I switch to Win7 Pro * 32 - bit * for Win7 Pro * 64 - bit *?

  If I use the recovery disk (the hidden recovery partition) utility to do a clean reinstallation of Win7 Pro, I will give the choice during the process of resettlement of the installation either the 32-bit version or 64-bit?

  Or I have + not + get the choice at all and simply be limited to the OEM Win7 Pro 32-bit that came pre-installed version?

  All advice or information about how to pass OEM Win7 Pro 32-bit to Win7 Pro 64-bit would be appreciated.

  Nick

  Hello

  AFAIK almost all new laptops are available with 32 and 64-bit OS and two recovery images are saved on the HARD drive.
  When you start installation HARD drive you should see the option to choose which version must be installed.

  Simply start the installation of HARD drive and you will see what menu you will see at the beginning. Not be afraid to do so. Nothing will happen.
  Real OS installation starts two steps later. If you can not damage preinstalled OS.

• Cannot install Windows 7 pro 64-bit on Satallite A200

  I have Win 7 pro 32 bit and I need to clean install 64 bit version. I don't have a Toshiba Satellite A200 model. psafoa and it won't start not dvd/usb or anything else than the main hard drive. I'm sure it's the bios. I can't change anything in the bios settings, I can change the boot order IE first usb etc, but it does not work. It won't start.

  Any help much appreciated, I tried for more than 20 hours. I already have the latest version of the driver for the bios that is from 2007, there are looong dam it. I need to install this for studies.
  I have the latest update for my bios and have followed the instructions from Toshiba and elsewhere.

  Again, I do not just want to install windos 7, I already have, I want to install windows 7 64 bit.

  Hello

  You do not need to change the boot order in the BIOS.
  You can boot from the CD/DVD drive using another way

  Press F12 after that laptop has propelled upward
  Then a start menu should appear there you must choose the STRANGE as boot device and should press ENTER.

  This would allow booting from the CD/DVD drive

  You can also press the C button immediately after the laptop has propelled this should allow both CD/DVD drive. !

• Maximum memory for Pavilion DV7t special edition running Windows 7 pro 64-bit with Intel i7 Q720

  I have an entertainment 2009 Dv7t Special Edition running on Windows 7 64 bit with intention processor i7 Q720 @1 .60GZ. I have 8 G of ram now but need to go to the top. Can I put two 8 G in the slots. Read some reviews say the software works and Windows 7 pro 64-bit can take up to 132 G RAM, if that was even possible. I run two internal drives. But with the addition of the cloud and running photoshop on cloud too much memory is used, slow down the computer. You want to go to 16. Everybody does and no problem?

  Thank you

  Hello

  As mentioned previously, there are SEVERAL dv7t editions and special editions. We have dv7t-3000, 4000-dv7t... and it is very difficult to find the right plug. Please use the following link to find the product/model number:

  http://support.HP.com/us-en/document/c00033108

  Your machine could be the following:

  http://h10025.www1.HP.com/ewfrf/wc/manualCategory?cc=us & dlc = in & lc = in & product = 5292645 &

  If so, the #4 on the following manual page it support 16 GB max:

  http://h10025.www1.HP.com/ewfrf/wc/manualCategory?cc=us & dlc = in & lc = in & product = 5292645 &

  You can have 2 x 8 GB, no choice. Only a few portable computers that have 4 slots and supports up to 32 GB. No way on this earth at this time, you can find a laptop that supports the 132 Gb of RAM.

  Kind regards.

• HP PavilionSleekbook 15-b009ee: HP Pavilion Sleekbook 15-b009ee Windows 7 Pro 64-bit drivers

  I need the Drivers of HP Pavilion Sleekbook 15-b009ee Windows 7 Pro 64 bit. Please if someone can sat down me.

  Hello:

  Try the W7 x 64 drivers and software for this model except the BIOS and firmware files.

  http://h22207.www2.HP.com/us-en/drivers/selfservice/HP-envy-Ultrabook-4-1100/5296027/model/5316650

  Your model uses the Intel HD graphics driver.

• HP Pavilion - 27qe touch everything-i: HP Pavilion - 27qe touchscreen all-in-one PC Downgrade of Win10 of Win7 Pro 64 bit

  I ordered, from hp store-still in production, a HP Pavilion - 27qe touchscreen all-in-one.  There are 10 Windows.  I would come down to Win7 Pro 64-bit (I can buy a legal copy of win7 and do a clean install).  I understand that I would lose some features like the touch screen, but I really prefer Win7.  I'm looking for info on how to do this?  For example, where to find the proper drivers (determine which and where to download to), BIOS etc.  Drivers listed on hp for this computer are for Win10 only, there is no Win7 drivers listed.  Of course I'd first recovery disks Win10, where I always want to go to the Win10 or if Win7 is not working properly.

  Any info/help appreciated.  My wife and I share one our computer at home with Win7 on it.  Me, my wife and probably would be better to use Win7 we are used and as.

  Thank you...

  Thanks for the info WAWood.  I decided to nix the idea of decommissioning.  It would be too complicated, as you point out.  Have a good!

  I noticed that you have been very busy here.  Member for 2 months and almost 500 posts!  Thanks for you disseminate knowledge and activity here.

• HP Pavilion Slimline s3760in D: need help in Clean install Windows 10 pro 64-bit?

  Hello

  For the past few months I am running windows 10 pro where I had to upgrade windows 8.1 pro 32 - bit windows 10 pro 32-bit. If my system is activated in windows 10 pro and it is authentic.

  

  When I checked in the type of system, it says operating system 32-bit, x 64 processor.  4 GB RAM only 3.12 GB of RAM is usable.

  This means that my processor supports 64-bit operating system. That's why I intend to clean windows install 10 pro and install the 64-bit version so that I can use all 4 GB of RAM.

  That's why went into a tool for creating media and downloaded Mediacreation Toolx64 but when I try to launch the app it shows error "this app cant run on your pc. But Mediacreation tool for 32 bit gently. According to me, given that my current OS is 32-bit so mediacreation toolx64 is not running.

  So I was wondering if I run 32-bit tool mediacreation and choose 'create multimedia installation for another pc' and chosen architecture (32-bit and 64-bit) times, then the clean installation of windows pro 10 OS will I have the option to choose between the version 64-bit and 32-bit version?

  [2] already my windows 10 pro is active in 32-bit version, I get a product key error when I clean install 10 pro for the 64 bit version of windows?

  [3] will be my windows 10 64-bit pro is activated? Since my windows 10 pro turned in a 32-bit version.

  Microsoft memo said "Your PC will activate online automatically as long as the same edition of Windows 10 has been activated successfully on this PC using the free Windows 10 upgrade offer."

  HI Varadar,

  You're right, you choose the installation program of the media creation tool that corresponds to your current system, but create a support for another PC and select 64-bit or both.  I would choose 64-bit.

  Yes, what you plan should work.  Once you have upgraded to Windows 10 32 - bit and Windows checked 10 32 - bit is set, you can use Media Setup to switch to Windows 10 64 - bit.  But... I could ask you to wait a month.  It was reported on the sites a Updatefor Windows 10 is expected in November.  This update will include some changes and corrections that we have already published to our group of insiders test.  The recent blog post is hereand scroll to the bottom of reading on the Activation stuff.  We also wrote about the changes, including the news of your task in our own forum.

  What do you think should work now today, if there is no problem or bug there is no backup.  But if you wait a bit, then the backup as explained will use your Windows 8.1 Pro key into your HP motherboard.

  I hope this helps,

  Charles

• BIOS 4.03 for workstation xw9400 running windows 7 pro 64-bit

  None does not know where and how can I update the bios on a running windows 7 pro 64-bit xw9400 (HP does not list in the drivers section?) currantly only got bios V3.13 and im sure it should be on atleast v4.03?

  see you soon

  Oh well all good now, worked to followed her the road to iso cd and managed to update the bios to version 4.03.
  
  Once again thanks for the support...
  
  Concerning
  Chardsky...

• Need a driver for usb controller for hp pavillion slimline 400 - 020l win 7 pro 64-bit

  Hi guys,.

  I need a driver of usb controller for hp pavillion slimline 400 - 020l win 7 pro 64-bit

  any help will be much appreciated

  Thank you

  Enter the Device Manager and right-click on the device without driver. Select Properties. Use the following image for example, to find the PCI\VEN string. Post it here.