Similar Questions

• How can I remove restrictions file from an external hard drive so I can view or access these files on any computer instead of just one file has first been created?

  I have an external hard drive that I loaded all my important files on all my computers. There is a file that I put in place restrictions to access, but it has been so long that I don't know how I did it or how to remove it. How can I remove restrictions file from an external hard drive so I can view or access these files on any computer instead of just one file has first been created? The computer that I created the folder of running Windows Vista. I am not able to access files in this folder from any other computer. It gives me the following error: "E:\School is not accessible. Access is denied. »

  Hi mango127,

  I suggest that you give all permissions for everyone on this folder and check if it works.

  "Access denied" error message when you try to open a folder

  http://support.Microsoft.com/kb/810881

  How to capture a file or a folder in Windows XP

  http://support.Microsoft.com/kb/308421

  If the previous step fails then I would suggest that you take the backup of this folder on the computer you were accessing and later to format the hard drive.

  How to use disk management to configure basic disks in Windows XP

  http://support.Microsoft.com/kb/309000

• (1) how to reset the task in view/default Access Manager? __2) how could it have been modified?-my firewall is off, too. I am concerned about safety.

  When I open the window (in Windows Vista) Task Manager, it shows that the "Applications" tab  I can access is more 'Processes', tab 'Performance' and 'Network'... this just started recently.
  (1) how to reset the task in view/default Access Manager?
  (2) how could it have been modified?-my firewall is off, too. I am concerned about safety.

  Double-click inside the border/edge to bring it back to the default view for Task Manager.

  Malware scan:

  Download, install, upgrade and scan with Malwarebytes to check / remove Malware/spyware.

  If necessary, do all of the above work Safe Mode with network.

   

  To get into Safe Mode with network, press F8 at the Power On / boot and use key arrow upward to get into SafeMode with networking from the list of options, and then press ENTER.

   

   

  http://www.Malwarebytes.org/MBAM.php

  Malwarebytes is as its name suggests, a Malware Remover!

  Download the free Version from the link above.

  Download, install, upgrade and scan once a fortnight

  How to use Malwarebytes once it is installed and updated:

  1. open Malwarebytes > click the update tab at the top > get the latest updates.

  2. on the Scanner tab, make sure that the Perform quick scan option is selected and then click on the Scan button to start scanning your computer

  3 MBAM will now start to scan your computer for malware. This process can take some time.

  4. when the scan is complete, a message box will appear

  5. you must click on the OK button to close the message box and continue the process of Malwareremoval.

  6. you will now be at the main scanner screen. At this point, you must click on the button to view the result .

  7. a screen showing all of the malware displayed the program that is

  8. you must now click remove selection button to remove all the listed malware. MBAM will now delete all of the files and registry keys and add them to the programs quarantine. When you remove files, MBAM may require a restart in order to eliminate some of them. If it displays a message stating that it needs to restart, please let him do. Once your computer has rebooted, and logged in, please continue with the remaining steps.

  9. when MBAM has finished remove the malware, it will open the scan log and display it in Notepad. See the log as desired, and then close the Notepad window.

  10. you can now exit the MBAM program.

  See you soon. Mick Murphy - Microsoft partner

• Failed to start the event viewer. Access is denied

  "Failed to start Event Viewer. Access is denied"message with a red x appears when I click on details of view in the event log in the task: advanced tools

  I am the administrater and the only user, the user account is disabled. I checked the register and complete the keys in Services/Eventlog 6 other tasks open OK, only the event log does not open.

  I have never used this service before, running Vista Business SP2 on a laptop HP Compaq8710p (7 years), all the drivers are up to date, I've checked for viruses and malicious software (Symantec Endpoint and Windows Defender). My HARD drive is only 45% used (55% free), 4 GB of memory.

  Would appreciate some help here

  Thank you

  Please run a check of system files (SFC) 

  
  

  All instructions are in our Wiki article below...
  If you have any questions please ask us for .

  Check the file system (CFS) Scan and repair system files

• Deliver the profile of the user - My Documents folder moved to C:\Documents and Settings\TEMP. I can't view or access this folder to copy My Documents back. Help?

  XP Home SP3 on my laptop (no not in network - independent).

  After an Adobe Reader 10 X installed, there is a reboot, and when I logged in the profile that appeared was not mine - it was as if it was a new installation. I looked for my personal documents under My Documents and did not find them. So, I looked for them on the C: drive, found (no not noted where), and copied My Documents to what seemed like the name /my Documents /. After that, I could access my documents by clicking Start-My Documents online. I did another reboot. Now, after login, my old profile is displayed, and the My Documents folder is empty except for the value by default my pictures, my music, my videos, and favorite - and these are all basically empty.

  I then ran a program Search and Recover to find my documents - they were found under C:\Documents and Settings\TEMP\. Unfortunately, I can't seem to see that to explore (I have it configured to display the hidden files and folders). Is it possible to go to this folder and the moving my Documents back to my profile?

  Thank you

  Ananth

  Hello

  You can view these methods:

  Method 1:

  Check to see if the problem exists in Safe Mode, if the computer works as expected in mode without failure, then we can solve the problem in the clean boot state.
  a. refer to the article below for the procedure safe mode in Windows XP
  A description of the options to start in Windows XP Mode
  http://support.Microsoft.com/kb/315222

  b. it is a possibility that there is a startup program that is launched with a command line and it appears.
  You need to perform a clean boot to find the program that is causing and then disable or remove.
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353/en-us
  Note: When you are finished troubleshooting, follow the steps as explained in the article to reset the computer to start as usual.

  Method 2:

  System Restore takes a "snapshot" of critical system files and some program files and the registry settings and stores this information as restore points. If your computer is not working properly, you can use these points to return Windows XP to a previous state when your computer was working properly restore. It can also change scripts, batch files, and other types of executable files on your computer.

  How to restore Windows XP to a previous state

  http://support.Microsoft.com/kb/306084

  I hope this helps.

• Foglight dashboard access to colleagues

  It's on dashboard foglight sharing with colleagues.

  I myself remember during training Foglight tutor provided a way to change the below url so that everyone can access and No need to connect to the foglight requests access to the dashboard.

  http://> / console/NOC/user:.4

  Could someone please advise how this is possible?

  I think that what you are looking for is access NoLoginUser.

  It has this nice video describing the process

  http://www.YouTube.com/watch?v=GRaOblam6P4

  Hope this helps

  Golan

• VMware View External access portal

  Hello

  I have configured my opinion of the Manager of connections for access from the web using a view Security server as a proxy. At the end I can connect via the web portal to connect to the server and can see the sources of funds that I added to my group, however!

  When I try to launch a source office sometimes as unavailable. As an exercise that I have linked to the external IP address using the customer view and I successfully launch my office.

  I can't understand why the web browser won't let me launch.

  Any suggestions are welcome.

  Rgds,

  Paul.

  Did you set correctly the URL "external"?

  Best regards

  Linjo

  If you find this information useful, please give points to "correct" or "useful".

• Pesonalizations forms 'View' without access to forms

  Hello
  
  We have a situation where the functional team would need to view customizations of forms on special forms (for most non-HTML forms) in R12.0.6, but did not have access to forms and certainly will not have access to the password apps (in production and non-production instances). Go see customizations through the interface user is not an option.
  
  Is there a handy query that we can run a toad that would give us this information? I guess it would be stored in fnd tables somewhere if anyone knows the actual tables?
  
  Any help will be most appreciated!
  Sasha

  Try this... he should at least give you a starting point and I'm sure that you can tailor/extend to your own needs.

  Kind regards
  Jon

  SELECT
  RUL.form_name - name of the form
  , rul.function_name - name of the function
  , rul.sequence - seq
  , rul.description - description
  , decode(rule_type,'F','Form','A','Function','') as plevel - level
  rul.enabled - active
  -CONDITIONS
  , rul.trigger_event - triggering event
  , rul.trigger_object - object trigger
  , rul.condition - condition
  , rul.fire_in_enter_query - processing mode
  -CONTEXT
  decode(sco.level_id,'10','Industry','20','Site','30','Responsibility','40','User','???') as context_level
  -ACTIONS
  act.sequence as action_seq
  act.property_value
  act.argument_type
  act.target_object
  decode(act.action_type,'P','Property','M','Message','B','Builtin','M','Menu','') as action_type
  act.enabled as act_enabled
  act.object_type
  act.message_type
  act.message_text
  act.summary
  act.builtin_type
  act.builtin_arguments
  act.language
  act.property_name
  Act. MENU_ENTRY
  act.menu_label
  act.menu_seperator
  act.menu_enabled_in
  act.menu_action
  act.menu_argument_long
  act.menu_argument_short
  Of
  fnd_form_custom_rules rul
  fnd_form_custom_scopes sco
  fnd_form_custom_actions Act
  WHERE 1 = 1
  AND rul.id = sco.rule_id (+)
  AND rul.id = act.rule_id (+)
  AND there are (select "is" the PRP fnd_form_custom_prop_list where act.object_type = prp.field_type)
  ORDER BY
  RUL.form_name, rul.function_name, rul.sequence, act.sequence

• Cannot view or access my local network of 'my network places '.

  Since the evolution of my router to router ZyWEL I can't diplay or access other computers on my local network. The entire network is invisible from all computers.

  Mallorcan salvation,

  Are a. When you facing this problem?

  B. you get errors?

  C. do you have a cable or a wireless network connection?

  D. the router is not compatible with vista?

  Have e. you checked if a firewall blocks the router?

  First check to see if a firewall is blocking the router then try the procedure below.

  Open Network Diagnostics by right-clicking the network icon in the notification area, and then click diagnose and repair.

  Make sure that all cables are connected (for example, make sure that your modem is connected to a working jack or cable phone connection, either directly or through a router).

  If you try to connect to another computer, make sure that this computer is turned on and that you have enabled file and printer sharing on your network. For more information, see networking of computers running different Windows versions.

  If your computer has a wireless network adapter, Windows automatically detects wireless networks that are located nearby. To see a list of wireless networks that Windows has detected, click the Start button and then click on connection to. If Windows does not detect a network that you think is in range of your computer, open help and Support and search for "Solving problems finding wireless networks."

  Try not the articles below.

  The problems of finding computers on a home network
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-finding-computers-on-a-home-network

  Solve problems with computers not appearing is not in the network map
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-computers-not-appearing-on-the-network-map

  Network connection problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  I hope this helps.

  Bindu S - Microsoft Support

  [If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]

• Flex Mobile: View parent access within the itemrenderer component Variable

  I have several images in a list and I want to display 4 of them both on the screen with a provision in mosaic with the width of each image = 50% of the height and width of screen = 50% screen height.

  I was able to do this with the code below.

  < s:List id = "list1" width = "100%" height = "100%" >

  < s:ArrayCollection >

  < fx:Object id = "img1" img_url = ' assets/1 - 1.png' title = "Image 1" / >

  < fx:Object id = "img2" img_url = "assets/1 - 2.png" title = "Image 2" / >

  < fx:Object id = "img3" img_url = "assets/2 - 1.png" title = "Image 3" / >

  < fx:Object id = "img4" img_url = "assets/2 - 2.png" title = "Image 4" / >

  < / s:ArrayCollection >

  < s:layout >

  < s:TileLayout

  columnAlign = "justifyUsingWidth" horizontalAlign = "center" verticalAlign = "middle".

  paddingBottom = paddingLeft '0' = '0' paddingRight = paddingTop = "0" "0".

  horizontalGap = "0" verticalGap = "0".

  / >

  < / s:layout >

  < s:itemRenderer >

  < fx:Component >

  < s:ItemRenderer >

  "< s:Group width ="160"height ="240">" "

  < s:BitmapImage source = "{data.img_url}" scaleMode = "stretch" smooth = 'true' "

  Width = "100%" height="100%"/ >

  < s:Label text = "{data.title}" left = low "0" = "0" width = "100%" / > "

  < / s:Group >

  < / s:ItemRenderer >

  < / fx:Component >

  < / s:itemRenderer >

  < / s:List >

  However, I don't want to hard code the width and height values.

  I am able to get the screen specify height and width in the event viewAcivate of the view, as shown below.

  protected function view1_viewActivateHandler(event:ViewNavigatorEvent):void

  {

  ScreenWidth = screen.width;

  ScreenHeight = screen.height;

  }

  How to apply these values for width/height of the group properties in the itemrenderer?

  Something like...

  < s:ItemRenderer >

  "< s:Group width ="{ScreenWidth/2}"height ="{ScreenHeight/2}' > ' "

  < s:BitmapImage source = "{data.img_url}" scaleMode = "stretch" smooth = 'true' "

  Width = "100%" height="100%"/ >

  < s:Label text = "{data.title}" left = low "0" = "0" width = "100%" / > "

  < / s:Group >

  < / s:ItemRenderer >

  parentDocument.height

• DW CS4 Live View - no access to the admin pages?

  Hello

  I've searched the forums, do not know if I ask the question properly.

  I'm still working on CS4 - I know that this feature has been added to the CS5, but I can't afford to update my entire system right now.

  I have the Live View installed correctly on my localhost and it works with my PHP pages.

  I don't know how to get the sections protected by password admin (CMS backend) of Live View?

  I found this help topic for custom URL requests, but honestly I have a usage example of this (provide the username and password?)

  http://help.Adobe.com/en_US/Dreamweaver/10.0_Using/WSC4A30901-005C-4721-B1DD-16F86D081698a .html

  can someone explain it to me in plain English? Thank you!

  Because the authentication of users requires SESSION VARIABLES, I am skeptical that you will be able to get to these pages in DW.  When I build things, I put the authentication on the very last step, after all the view of the page/Live layout issues have been addressed.

• Access to ISE's dashboard

  Hello

  I'm under distributed deployment with mutiple Ssnp, MONs & Admin nodes are deployed. I was check crtical vlan access and criteria dead radius server and a scenrios of test cases for reboot/turn off devices since a while and trun on back and check the service. But after that devices came I lost dashboard access there is no GUI access even if I'm still able to access all devices through CLI.

  Could you please help me to identify the problem.

  following output for the referance.

  """"""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""

  isea001 / admin # display application status ise

  ISE database listener is running, PID: 4947
  ISE database is running, process number: 29
  ISE Application Server process is not running.
  ISE Profiler DB is running, PID: 6173
  ISE M & T Session database is not running.
  ISE M & T Log Collector does not run.
  ISE M & T journal processor does not run.

  """""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""

  isem001 / admin # display application status ise

  ISE database listener is running, PID: 4952
  ISE database is running, process number: 23
  ISE Application Server process is not running.
  ISE Profiler DB is running, PID: 6131
  Database Session M & T ISE is running, PID: 4646
  ISE M & T Log Collector is running, PID: 6625
  ISE M & T journal processor does not run.

  """""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""

  isep001 / admin # display application status ise

  ISE database listener is running, PID: 4955
  ISE database is running, process number: 23
  ISE Application Server process is not running.
  ISE Profiler DB is running, PID: 6215
  ISE M & T Session database is not running.
  ISE M & T Log Collector does not run.
  ISE M & T journal processor does not run.

  """"""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""

  isep002 / admin # display application status ise

  ISE database listener is running, PID: 4953
  ISE database is running, process number: 23
  ISE Application Server process is not running.
  ISE Profiler DB is running, PID: 6171
  ISE M & T Session database is not running.
  ISE M & T Log Collector does not run.
  ISE M & T journal processor does not run.

  """""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""

  Thank you for taking the time to come back and the solution to the problem of sharing! (+ 5 from me). If you happen to be the ID of the bug please share as well!

  In addition, if your problem is resolved, you must mark the thread as "answered" :)

• Access view horizon 5.3 HTML won't load - white screen

  I recently updated a view from 5.2 to 5.3 demo environment.  Now that the upgrade is complete, access HTML no longer works.  I have install access HTML on the login server component after the 5.3, as directed by VMware docs update.  I built the new Windows 7 and Windows 8.1 VMs and installed the agent, and then the pack remote experiment, according to the same docs.  If I connect to the server to display login and select Horizon View HTML Access, it prompts you to connect and then show me the pools that I set up.  When I click on a pool, the screen slides laterally to the Bureau and then sits on gray background and never loads.  Eventually the connection times out on the desktop of the target.  I tested with Windows 7 and 8.1 pools the base with the same results.  The two pool work very well in the native mode client.  I tried connecting from the security server and the login server internal with the same questions.  If someone has encountered this or could provide some troubleshooting resources, it would be great.  Here is a brief description of the environment:

  Connection to the server: Windows 2008R2 - view 5.3 with HTML access feature

  Security Server: Windows 2008R2 - view 5.3 (no firewall between the login server and security server - demo)

  Composer - Windows 2008R2 with SQL Server 2008R2 - composer 5.3 Server

  Pools:

  Pool 1 - persistent related Clone Windows 8.1

  Pool 2 - model persistent Windows 7

  vCenter: vCenter Unit 5.5

  The ESX servers: ESXi 5.5

  Well I thought about it.  I said to PCoIP external IP address to the internal IP address of the Security Server and no public IP address.  After fixing remote sessions that seem good.  That teaches me to update an environment at night when I'm already tired.  Thanks for the help Linjo!

• View horizon 5.2 - can't loging via access HTML

  Hi all

  I followed these steps:

  1. I installed Vmware View html access in my opinion Horizon connection server without any problems.
  2. I installed "VMware-Horizon-View-5.2-Remote-Experience-Agent-1.0-1046150" in my VM that I'll use in my pool of test.
  3. I have build a new POOL and called a user test. Currently, all steps have been ok.

  But when I try to connect to my VDI I can connect via VIEW HORIZION Client but not via the html access. Via html access I can connect but I cannot connect to my VDI because it shows this message:

  You are allowed to use the system.

  Why work with customer view and not via the html access? Could someone help me?

  Concerning

  Go swimming on your desktop and select the check box for the HTML access.  Default value is uncheck.

  Please note desktop on Windows XP is to have a bug.  Only Windows 7 and 8 work.

• Licenses required to access VNC

  Hi all

  I'm sorry to have potentially posted this in the wrong forum first! I am trying to wrap my head around the following question:

  I have a tool that I want to give access ratings to. It is a piece of software to interface with a telephone system that displays stats about who is currently signed as a live dashboard. The software does not allow many people to access.

  So I would do is to give a handful of users view only access via VNC. Which means that I would run this software on a server, then x users all connect at the office same server as a view-only clients.

  I know what to do on the side VNC - what is purchase x number of enterprise license allowing x number of clients to connect to.

  But how I stand on the licenses of Windows? Assuming I have install this application on Windows Server 2008 or Windows Server 2012, am I right in thinking I would also need to buy x user licenses? Or does somehow make a difference that all clients are connecting on the same desktop in read-only mode?

  Thanks a lot for any input.

  Martin

  Ask in the forum Windows Server:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer