VLAN and VPN problem

Similar Questions

• configuration of VLAN and routing problem 6224 switch

  I, m having a problem accessing internet to vlan 10. I can ping everything of all the VLANS. My internet router/firewall is on ethernet 1/g11 and has an ip address of 192.168.5.254. I have no problem accessing internet to vlan 20. I add a static route to my router/firewall. What Miss me? This is my first configure a layer 3 switch.

  Configure
  database of VLAN
  VLAN 10.20
  output
  battery
  1 1 member
  output
  IP 10.10.10.1 255.255.255.0
  default IP gateway - 10.10.10.254
  IP routing
  IP route 0.0.0.0 0.0.0.0 192.168.5.254
  interface vlan 10
  Routing
  IP 192.168.100.1 address 255.255.255.0
  output
  interface vlan 20
  Routing

  192.168.5.1 IP address 255.255.255.0
  output

  !
  interface ethernet 1/g1
  switchport mode general
  pvid switchport General 10
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 10
  output
  !
  interface ethernet 1/g2
  switchport mode general
  pvid switchport General 10
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 10
  output
  !
  interface ethernet 1/g11
  switchport mode general
  switchport General pvid 20

  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 20
  output
  !
  interface ethernet 1/g12
  switchport mode general
  switchport General pvid 20
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 20
  output
  !
  interface ethernet 1/g13
  switchport mode general
  switchport General pvid 20
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 20
  output
  output

  Route ip console #show

  The traffic code: R - RIP derived, O - OSPF derived, C - connected, S - static
  B - BGP derived, IA - OSPF Inter zone
  E1 - OSPF external Type 1, E2 - OSPF external Type 2
  N1 - OSPF NSSA external Type 1, N2 - OSPF NSSA external Type 2

  S 0.0.0.0/0 [1/0] via 192.168.5.254, vlan 20
  C 192.168.5.0/24 [0/0], directly connected, vlan 20
  192.168.100.0/24 C [0/0], directly connected, vlan 10

  Console #.

  
  

• Cisco 1921 & SG500 VLAN and DHCP problem

  Dear all,

  Thank you in advance for taking the time to read this.

  A little history:

  I want to install a project for an athlete, which is unfortunately on a budget pretty tight with a potentially large quantity of network users (~ 200 without public WIFI). I need to separate the 5 groups of users and to give them all access to internet without see each other. 5 user groups also share the same bandwidth to the internet and VLANs must be controlled bandwidth.

  To do this, I had planned to use Cisco devices built-in functions and buy a 1921 Cisco router as a switch of SG500.

  I have configured the router for 8 subinterfaces is internal NIC with 8 VLAN. I also configured DHCP Pools 8 on the 1921 and set up NAT and firewall.

  What I want to do now is have the SG500 to recognize the VLAN ID, I configured on the router (as well as on the switch using the same VLAN ID numbers), and then assign ports to the VLAN on the switch, and depending on where I plug into the switch, the device receives different IP addresses from DHCP.

  However, I can't get this to work. The router works fine, the 'intact' if left switch gives me an IP address from the DHCP server on the IP address of higher network VLAN (I.e. 168.8.0). but I can not configure the switch ports correctly so that it works. I was also confused, is that dhcp pools that I have configured on the command-line command on the router do not appear in professional CP in the mask of the pool.

  Can someone kindly check the configuration of the router and throw some guidance on how I need to configure the Ports on the SG500? I must say that I have had too many nights and I seem to confuse tagging, untagging, to exclusion and prohibiting the ;.)

  I have the router for you here:

  Thanks again and good night!

  W.

  Hi Wolfgang, for the sx500 configuration can be something like this

  config t

  database of VLAN

  VLAN 2-8

  int item in gi1/1/1

  switchport mode general

  switchport trunk allowed vlan add 2-8 tag

  switchport General disable filtering of capture

  For any client that connects must be no tagged coelio

  So if you want a client access port then you should do something like 5 unidentified to this port

  config t

  int item in gi1/1/2

  switchport mode access

  switchport access vlan 5

  -Tom
  Please mark replied messages useful

• LRT214 VLAN and site to site vpn

  Hello everyone, I am a bit new to the network of this aspect and was looking for some advice.  I am looking for several routers LRT214 to configure VPN site to site to our main office at 4 locations.  There are 2 VLANS and subnets - one for the network secure (vlan native 1) and one for comments wireless (vlan 2).  It is very good and works well for lan segregation locally.

  IPSEC tunnels do not pass the tags vlan, my question because I will be able to restrict traffic through the vpn tunnel to vlan 1 and deny traffic to vlan 2?

  It appears in the documentation that VPN traffic can be limited by IP address or the local subnet.  My concern is that if there is no way to bind or bridge to the VLAN selected, an adjustable static IP address on a device on the vlan 2 were part of the traffic permitted (vlan 1 range), and therefore cross the tunnel for devices vlan 1 on remote sites.

  Thanks for any input you can offer.

  Hi, seedtech. The VLAN used for the VPN is the default VLAN. So if a tunnel is created, it will cross through the default VLAN.

  Jay-15354

  Linksys technical support

• problem with Ezvpn and VPN from Site to Site

  Hello

  I want to set Ezvpn and VPN Site to another but the problem is that the EasyVpn that would only work at the Site to the Site does not at all

  I have set up 1 card for two VPN with different tagged crypto

  I had execlude the traffice to NOT be natted to, and when I remove the Ezvpn site to another work well

  crypto ISAKMP policy 100
  BA aes
  md5 hash
  preshared authentication
  Group 2
  !
  crypto ISAKMP policy 10000
  BA aes 256
  preshared authentication
  Group 5
  key address 123456 crypto isakmp (deleted)

  ISAKMP crypto client configuration group easyvpn
  easyvpn key
  domain ezvpn
  pool easyvpn
  ACL easyvpn
  Save-password
  Split-dns cme
  MAX User 9
  netmask 255.255.255.0
  !

  Crypto ipsec transform-set esp - aes 256 esp-sha-hmac vpn

  Crypto-map dynamic easyvpn 10
  Set transform-set dmvpn
  market arriere-route
  !
  !
  address-card crypto easyvpn local Dialer1
  card crypto client easyvpn of authentication list easyvpn
  card crypto isakmp authorization list easyvpn easyvpn
  client configuration address card crypto easyvpn answer
  easyvpn 100 card crypto ipsec-isakmp dynamic easyvpn
  easyvpn 1000 ipsec-isakmp crypto map
  defined by the peers (deleted)
  Set transform-set vpn
  game site address

  interface Dialer1
  the negotiated IP address
  IP mtu 1492
  NAT outside IP
  IP virtual-reassembly
  encapsulation ppp
  Dialer pool 1
  PPP authentication chap callin pap
  PPP chap hostname
  PPP chap password
  PPP pap sent-name to user
  easyVPN card crypto

  DSL_ACCESSLIST extended IP access list
  deny ip 100.0.0.0 0.0.0.255 101.1.1.0 0.0.0.255
  deny ip 100.0.0.0 0.0.0.255 70.0.0.0 0.0.0.255
  IP 100.0.0.0 allow 0.0.0.255 any
  refuse an entire ip
  easyvpn extended IP access list
  IP 100.0.0.0 allow 0.0.0.255 70.0.0.0 0.0.0.255
  IP extended site access list
  IP 100.0.0.0 allow 0.0.0.255 101.1.1.0 0.0.0.255

  Best regards

  The sequence number of card crypto for the static mapping crypto (site to site vpn) should be higher (ie: sequence number must be lower) than the ezvpn (map dynamic crypto).

  In your case, you must configure as follows:

  map easyvpn 10 ipsec-isakmp crypto
  defined by the peers (deleted)
  Set transform-set vpn
  game site address

  map easyvpn 150 - ipsec-isakmp crypto dynamic easyvpn

  Hope that solves this problem.

• Implementation of VLAN and QoS for VOIP on SG200-18

  We recently purchased the smart switch SG200-18 to replace a Netgear switch. We are moving our phone service to VOIP through our local ISP as well.

  I currently have the VOIP phone plugged into Port 17 on SG200-18 (it is a Grandstream Cordless VOIP phone).

  I want to put the VOIP phone on one VLAN separate from the rest of the network and optimize QoS parameters so that the VOIP phone has exceptional audio quality even during network traffic.

  Here are my questions:

  1. do I need to set anything on the type of port to Port 17 (because it resembles a shape any Combo port)?

  2. How can I do to isolate VOIP telephone it's own VLAN (I see the parameters VLANS and VLAN voice, not sure that one to use;) I've tried to set a VLAN and broke the Internet connectivity on the phone until I went and removed)?

  3. do I need to adjust the QoS settings to switch to better optimize the VOIP phone?

  Some additional questions about the GS200-18 in general:

  1. do I need to adjust the parameters of the system on the switch time? I am in the Central time.

  2. do I need to adjust the Green Ethernet/Energy Saving parameters or should I stay with the default settings?

  In addition, a couple of "getting started" questions for Cisco:

  1. I registered an account My Cisco. What should I do to register my switch with Cisco and associate with my My Cisco account?

  2. What are the benefits of purchasing a contract of Cisco Small Business support, and how much would it cost the SG200-18 (I ordered it from Provantage)? I'm curious to see if it's worth the money.

  Here's my 'features ':

  Switch: SG200-18

  VOIP phone: Grandstream DP715 and 710 handsets

  Plugged in: Port 17 on SG200-18

  Services: Internet Local (Direclynx)

  Type of connection: 3 m down / 500 k up DSL move to a future wireless connection that will give us higher speeds

  Backend VOIP provider: VOIP Innovations

  Router: Apple Airport Extreme AC model (all Macs and iOS devices and the OS X Server on the network, so I use the Apple router facilitates installation, because is not QoS, trying to QoS and VLAN in the switch)

  Thank you all!

  Hello

  I'll just go to the list again:

  1. sounds good in the port from the drop-down list. So can I just connect the VOIP phone and go with it, correct?

  Yes, just plug in ethernet combo port and it will work.

  2. is not an issue, but I agree, Apple likely isn't compatible QoS or VLAN.

  3. thanks for the info on time/NTP settings. If I wanted to go there and try to configure NTP, how much is it and what I have to do? I want to I can give it a quick try.

  To Setup NTP on the switch is quite simple.  Go to Administration > Time Settings > time system and check the boxes to activate the main clock Source (SNTP)

  Then go to the settings of the SNTP page and add a new entry with the IP address of an NTP server.  There is a list of available NTP servers here:

  http://www.pool.ntp.org/en/

  You must also ensure that the switches Administrative default gateway is set correctly (it must be set the to the default gateway, probably the most convenient airport) so the switch can contact the NTP server.  That option is set under Administration > Interface Management > Interface IPv4.  Change the user-defined default gateway and enter the IP address of your airport (or whatever your default gateway for your network)

  4 sounds good on the Green Ethernet settings. I'll leave it as default value.

  Yes, better to just let those unless you have weird problems with ports disconnect, who can sometimes be caused by Green Ethernet, but if there's nothing like leave it on and save a few watts.

  5 sounds good on does not need to attach my passage to my Cisco account. Should I fill out a form any registration of the product with Cisco before calling support?

  It is not a record for support.  The only thing we need you to do is to create a Cisco account, but you have already done this, so if/when you call in support, you just need your ID for Cisco (also called a CCOID sometimes) and the serial number of your switch.

  6. thanks for the info on the Service contract. Is it something that I would need to order directly from Cisco or I who would get my Cisco partner (Provantage)? After the three years is up, treat yourself to renewal or it just falls? Is there a certain amount of time I have to buy the Service Contract forward make me ineligible?

  Support contracts are purchased through a partner Cisco, or you can get them online for the CDW or Newegg for example.  Basically, you have until the expiry of your current aid for the purchase of a new contract.  For example, right now your switch comes with 1 year of technical support.  You can only buy a contract while it is still active.  Once your three-year contract is about to run out, you're in the same situation.  You can renew it before it expires, however if you leave is up, you will not be able to put a contract on it.  Contracts are not my specialty, however, so you can check with your partner for complete details.

  7. sounds good to how data use VOIP calls. His dislikes too. :-)

  I agree, a voice call is not much traffic.  What you have described you probably don't have problems, although of course I can't guarantee that.

  8. because it is from your provider and they specifically mentioned the VOIP, I would say that you'll be fine here.

  You had also placed on your airport using access point behind a router in small businesses.  I would like to say that it is possible, a large number of wireless routers have an option to put access point only mode or something like that, but you should check with Apple on how to do it.

  Insofar as a Small Business router if you decide to upgrade for the options VLAN or QoS, I would recommend the RV180, or perhaps the RV320.  Two of these models are available with or without wire depending on what you decide to do with the airport.

  I think I got all the questions, but if not just let me know,

  Christopher Ebert - Network Support Engineer

  Cisco Small Business Support Center

  * Please note the useful messages *.

• SGE2010 switches, VLAN and a port blocked by spanning tree

  People,

  I have 2 groups of switch.

  SGE2010 2 with VLANS is defined as 10,20 and 30

  VLAN 10 is the management VLAN and it uplinks to our border router.

  VLAN 20 is the workstation VLAN, and all workstations are pointing to the switch as their default GW

  VLAN 30 is the ip phone VLANS, and all phones use this as a gateway.

  I have a GAP between the switches said, we have a few servers on the ip phone switch that must be accessed by the clients of the workstation and the unique link of 100 MB through the router probably won't be enough.

  If I understand correctly, because the switches have different networks on them, a simple shift will not work. I did create a gap and addresses on each side, but it does not appear in this mode, I can block vlan 10 transit to the LAG, with this block I'll end with a logic loop and spanning tree will block the uplinks or LAG itself.

  I have attached a picture with a diagram of our current put in place.

  Any help/advice would be much appreciated.

  John, the 802 standard. 1 initial q indicates there isn't only global tree covering weight independently of belonging to a vlan. It's why you run into problems. Cisco has developed PVST to run on circuits of the ISL. BPMH was originally defined as 802. 1s, which is a combination of 802. 1 q + RSTP. The 802. 1s were later modified to become part of the 802. 1 q.

  The person is incorrect, because they cite "because spanning tree is construction by vlan. They are incorrect, because you have to set the properties of tree cover to allow the spanning tree protocols by vlan. Small business switches do not support the owner Cisco PVST and PVST +. However, the SB switches support BPMH which is a standard of the IEEE.

  How works the BPMH, it's that you have called proceeding, i.e. each construction covering tree. Then you have the region, SB switches support only 1 region. The region maintains the instances. Basically how it works, you activate the EMU at the global level. Then, you specify the instance. As an example, the vlan 1 is instance 1. VLAN 2 is 2.  This will allow you to run 2 physical wires between switches vlan different without looping. If you use classic STP or RSTP, the least costly path will go to the State to block/cast who works as expected.

  -Tom

• Can fast VPN and VPN Cisco coexist (WRVS4400N)

  I am looking to buy a WRVS4400N to take care of my home network.  While I get out on the road I want to VPN in my home network to my laptop (on which I installed Cisco VPN for the company's mobile access to my corporate network).  In this spirit, I have three questions:

  1. is the Cisco VPN client on my laptop be able to establish a VPN connection to unity WRVS4400N?  I suspect not, and instead, I have to use fast VPN.

  2. I understand there are problems in co existence with different suppliers, VPN clients (when I tried before with a Netgear router, the VPN Netgear client broke the Cisco VPN client).  Quick VPN client Linksys can coexist with the Cisco VPN client without any problems?

  3. a last resort, if Cisco and Linksys VPN can coexist, install the client quick VPN Linksys inside a VM Ware image would work (while the Cisco VPN client is still installed in the host operating system).

  Thanks much for any help.

  (1) correct.  For WRVS4400N QVPN

  (2) I run the Cisco VPN CLient and VPN fast on my laptop and seems fine

• PIX VPN problem!

  Hello

  I have currently having problem with vpn, the pix pix506e works fine yesterday, but today morning that the problem appears, the pix did more than 2 connections vpn client, if the user connected, user B will cut this time... If the user B, user A logs off, I write erase config and rebuild again with the base, but still the problem occurs, what could be the problem, software or... material? Here I am attaching my beginning of basic config and vpn client connection.

  Our network is down now... Help, please.

  118 17:07:12.460 12/16/04 Sev = Info/6 IKE/0x6300003D

  Sending DPD asks 218.xxx.xxx.161, seq # = 1257657895

  119 17:07:12.460 12/16/04 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to 218.xxx.xxx.161

  120 17:07:17.468 16/12/04 Sev = Info/6 IKE/0x6300003D

  Sending DPD asks 218.xxx.xxx.161, seq # = 1257657896

  121 17:07:17.468 16/12/04 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to 218.xxx.xxx.161

  122 17:07:22.475 12/16/04 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK INFO *(HASH, DEL) to 218.xxx.xxx.161

  123 17:07:22.475 12/16/04 Sev = Info/5 IKE / 0 x 63000018

  Deleting IPsec security association: (OUTBOUND SPI = 695320B 5 SPI INCOMING = F0A2471)

  124 17:07:22.475 12/16/04 Sev = Info/4 IKE / 0 x 63000048

  IPsec security association negotiation made scrapped, MsgID = 7A8F1E11

  125 17:07:22.475 12/16/04 Sev = Info/4 IKE / 0 x 63000017

  Marking of IKE SA delete (I_Cookie = BAF3D743B1D25DD6 R_Cookie = ED5BAEF920BA3244) reason = DEL_REASON_PEER_NOT_RESPONDING

  126 17:07:22.475 12/16/04 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK INFO *(HASH, DEL) to 218.xxx.xxx.161

  127 17:07:22.475 12/16/04 Sev = Info/4 IPSEC / 0 x 63700013

  Delete the internal key with SPI = 0x71240a0f

  128 17:07:22.475 12/16/04 Sev = Info/4 IPSEC/0x6370000C

  Key removed by SPI 0x71240a0f

  129 17:07:22.475 12/16/04 Sev = Info/4 IPSEC / 0 x 63700013

  Delete the internal key with SPI = 0xb5205369

  130 17:07:22.475 16/12/04 Sev = Info/4 IPSEC/0x6370000C

  Key removed by SPI 0xb5205369

  131 17:07:22.986 12/16/04 Sev = Info/4 IKE/0x6300004A

  IKE negotiation to throw HIS (I_Cookie = BAF3D743B1D25DD6 R_Cookie = ED5BAEF920BA3244) reason = DEL_REASON_PEER_NOT_RESPONDING

  132 17:07:22.986 12/16/04 Sev = Info/4 CM / 0 x 63100013

  ITS phase 1 deleted because of DEL_REASON_PEER_NOT_RESPONDING. 0 ITS phase 1 currently in the system

  133 17:07:22.996 16/12/04 Sev = Info/5 CM / 0 x 63100025

  Initializing CVPNDrv

  134 17:07:23.106 12/16/04 Sev = Info/6 CM / 0 x 63100031

  Head of network device tunnel 218.xxx.xxx.161 disconnected: duration: 0 days 0:16:44

  135 17:07:23.286 16/12/04 Sev = Info/4 IKE / 0 x 63000001

  Signal received IKE to complete the VPN connection

  138 17:07:23.316 12/16/04 Sev = Info/6 CM / 0 x 63100037

  The routing table was returned to the original state before virtual card

  139 17:07:25.649 12/16/04 Sev = Info/4 CM / 0 x 63100035

  The virtual adapter has been disabled

  140 17:07:25.699 16/12/04 Sev = Info/4 IKE / 0 x 63000085

  Service Microsoft's IPSec Policy Agent started successfully

  141 17:07:25.699 16/12/04 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  142 17:07:25.699 16/12/04 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  143 17:07:25.699 12/16/04 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  144 17:07:25.699 12/16/04 Sev = Info/4 IPSEC/0x6370000A

  IPSec driver successfully stopped

  Thank you

  Tonny

  In your PIX, enter the following command:

  ISAKMP nat-traversal

• Site to site VPN problems

  Hello, I'm having a problem with my VPN configuration. I have two locations each with she is has a subnett. I have a VPN site-to site between the two locations. The site to site VPN is up and fully functional without any problem. Now if I'm away from work and to connect with the site A VPN client, I cannot ping or connect what either on site B. Or if I am connected to site B by a VPN I can't ping or connect what to site A.

  I hope that makes sense, but I'll be happy to give more details on Setup if necessary.

  I think that the command you need is:

  same-security-traffic permit Intra-interface (not inter-interface)

  The remote VPN and VPN site - to use the same outside interface, so this command allows VPN traffic out this interface pin

  Sent by Cisco Support technique iPad App

• Router vpn site to site PIX and vpn client

  I have two on one interface on the pix vpn connections that terminate VPN. client vpn and VPN site-to-site have passed phase one and two and decrypt and encrypt the packets. However as in another post I can not ping through the l2l vpn. I checked this isn't a nat problem a nd two NAT 0 on the pix and the NAT on the router access lists work correctly.

  ISAKMP crypto RTR #show its
  IPv4 Crypto ISAKMP Security Association
  status of DST CBC State conn-id slot
  66.x.x.x 89.x.x.x QM_IDLE 2001 0 ACTIVE

  IPv6 Crypto ISAKMP Security Association

  local ident (addr, mask, prot, port): (192.168.2.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (192.168.10.0/255.255.255.0/0/0)
  current_peer 66.x.x.x port 500
  LICENCE, flags is {origin_is_acl},
  #pkts program: 23583, #pkts encrypt: 23583 #pkts digest: 23583
  #pkts decaps: 18236, #pkts decrypt: 18236, #pkts check: 18236
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 0, #pkts compr. has failed: 0
  #pkts not unpacked: 0, #pkts decompress failed: 0
  #send 40, #recv errors 0

  local crypto endpt. : 89.x.x.x, remote Start crypto. : 66.x.x.x
  Path mtu 1380, ip mtu 1380, ip mtu BID Dialer0
  current outbound SPI: 0xC4BAC5E (206285918)

  SAS of the esp on arrival:
  SPI: 0xD7848FB (225986811)
  transform: aes - esp esp-sha-hmac.
  running parameters = {Tunnel}
  Conn ID: 3, flow_id: Motorola SEC 1.0:3, card crypto: PIX_MAP
  calendar of his: service life remaining (k/s) key: (4573083/78319)
  Size IV: 16 bytes
  support for replay detection: Y
  Status: ACTIVE

  the arrival ah sas:

  SAS of the CFP on arrival:

  outgoing esp sas:
  SPI: 0xC4BAC5E (206285918)
  transform: aes - esp esp-sha-hmac.
  running parameters = {Tunnel}
  Conn ID: 4, flow_id: Motorola SEC 1.0:4, card crypto: PIX_MAP
  calendar of his: service life remaining (k/s) key: (4572001/78319)
  Size IV: 16 bytes
  support for replay detection: Y
  Status: ACTIVE

  outgoing ah sas:

  outgoing CFP sas:

  Expand the IP NAT access list
  10 deny ip 192.168.2.0 0.0.0.255 192.168.10.0 0.0.0.255 (21396 matches)
  20 permit ip 192.168.2.0 0.0.0.255 everything (362 matches)
  Expand the IP VPN_ACCESS access list
  10 permit ip 192.168.20.0 0.0.0.255 192.168.10.0 0.0.0.255 (39724 matches)

  I looked on the internet and that it points to a routing error when packets are being encrypted and decrypted, but you can't do a ping on the binding. However when I test the connection I did not enter any of the static routes that networks are connected directly on each side of the pix and the router. any help would be a preciated as I think there's maybe something is blocking the ping to reach the internal network at the end of pix with a configured access list.

  is ping failure of the only thing between the site to site VPN? and assuming that all other traffic works fine since it decrypts and encrypts the packets.

  If it's just ping, then activate pls what follows on the PIX:

  If it is version 6.3 and below: fixup protocol icmp

  If it is version 7.0 and higher: select "inspect icmp" under your political map of the world.

  Config complete hand and on the other could help determine if it's a configuration problem or another problem.

• Mapping VLAN and probe Inline

  Hello

  I'm doing all my traffic flow of SSL VPN clients through a traffic Inline probe. From what I see, I should use the mapping feature VLAN. But I can't understand how the function works. ASA not very informative or extensive documentation.

  Currently my ASA has a network of interconnection on a VLAN to my router base, and all my internal network is routed to the base IP address. Default gateway of the router of my Core is the ASA. My ASA provides IP addresses to remote VPN SSL clients and is the default router for them. Remote traffic follows the remote client to the ASA, then through the interconnection to my internal networks. My only ASA works as my perimeter firewall and SSL VPN concentrator.

  I have map VLAN undestand will make all traffic from the remote clients to abandon the vehicle on a VLAN individual. So, I created a new VLAN and that added to a trunk on the SAA. Then I activated "restrict access to VLAN" and set it to my VIRTUAL LAN. My traffic Inline probe is connected to the VLAN and can provide DHCP.

  If it were a classic network, I'd Inline traffic probe the gateway by default for this VLAN and provide IP addresses and gateway with its DHCP server. But how does it work with ASA? I can in captivity the evacuation to this VLAN, but cannot find a way to make the traffic passes through the screen. As ASA does not support routing based on the source can't make the jump next to the probe traffic.

  I can do the bridge of the probe (L2) network for interconnection and the remote client VLAN. But the IP address of the ASA on the VLAN does not fall within the same range as the interconnection, so I can't understand if and how it worked.

  Can someone help me with the configuration or explaing me better how works the mapping VLAN?

  Thank you.

  What you are trying to reach is configurable through the "tunnel" default route, and it would force all traffic of VPN with this default route special.

  for example:

  If your traffic probe Inline between the ASA inside your heart and the interface, you can configure:

  Route inside 0.0.0.0 0.0.0.0 in tunnel

  Requiring all VPN traffic route to IP CORE that would go through your online traffic probe

  Here's the order for your info reference:

  http://www.Cisco.com/en/us/docs/security/ASA/asa83/command/reference/QR.html#wp1840612

  Hope that helps.

• Tagged management VLAN and the virtual machines on the same VLAN

  I'm faced with a problem related to our Brocade switches newly acquired and get the private VLAN to work on trunk connections to our ESX servers.  Every time I try something different, he creates a new problem.

  In our configuration, our management of VLAN is not tag and we have a VLAN for this management network that is placed on our switches VLAN no marked native.  We also have virtual machines hosted on those same ESX servers that are on the same VLAN and everything works fine.  However, when I change the ESX management to carry a label on this VLAN and change the switchports accordingly (IE no untagged VLAN native), management work, but hosted on the ESX Server machines that are on the same VLAN can get no network connectivity.

  Is it possible to have a management network labeled and also the host of virtual machines on the same VLAN or is it totally impossible?  I'm not very familiar with networking behind ESX, so I apologize if this is a dumb question with an obvious answer.

  Thank you

  Mark J.

  Is it possible to have a management network labeled and also the host of virtual machines on the same VLAN or is it totally impossible?

  Yes, it is possible... why it doesn't work for you I don't know, but try the following:

  1. set up the Group of ports of VMS to use VLAN;

  2 configure the interface of management VMkernel port group use VLAN;

  3 configure the physical switch port to allow to this VLAN and put the default VLAN natively for these interfaces.

• VMware Fusion 5 with Windows 8 and VPN

  Hi, I'm new to VMware. I am connected to my company via wifi VPN. I configured the VMware to connect through NAT. VPN seems to work fine on OSX, but in windows (VM) it says "no internet access. Internet works fine when I'm not on the VPN, but as soon as I connect to the VPN connection is lost. I tried to reload the OSX and Windows number of times. I tried ipconfig/release, ipconfig / renew on windows as suggested by other posts.

  Please let me know if you have any ideas to get this to work.

  In addition, the VPN was working fine until recently on another Terminal Wifi. I'm traveling now and I am facing this problem with wifi again. Not sure if there is wifi problem. Although I doubt that because the internet seems to work fine without a VPN and VPN seems to work fine under OSX. It's just VPN on VM that has a problem.

  I agree to what Akotsur said. Probably, you might consider configuring VPN Windows separately keeping in bridged mode.

• GPS, Wifi and Bluetooth problems

  So I have an iPhone 6 running on IOS 9.3.4 and have had problems with the GPS and the strength of wifi connectivity and bluetooth for a while now.

  First of all, the GPS.  It does not work.  When I run the maps or google maps on my device and the input an address the app can give me a written plan, location, but will not show me on a map.  He'll start road to everywhere where I go and tell me to start position, for example, to the North on the road on that I am, but the arrow does not follow me and tell me when the turn or where I am.  Occasionally, he has a message of guidance down with a spinning wheel and then, after a few seconds, disappears.  I tried to reboot my device several times, I have reset the network setting, I reset all of the settings, I backed up my phone, reset it and recovered save him.  Nothing has worked.  I was at my local verizon store and received a 'new' (its definitely refurbished) phone and the problem persists on the new phone.  I reset the phone to factory setting without content, set up as a new phone and tried the cards again, thinking it might be a problem with the back to the top.  It still does not work.  I'm perplexed right now and do not know what to do/try.

  Second, wifi and bluetooth connectivity is terrible.  I can only receive a wireless signal so that in very close proximity with the router.  I tried to different houses/companies and it is the same question.  However, bluetooth is just as bad.  I use headphones wireless, and go to the gym/go for the route with them.  I used to be able to walk around the gym without my phone and have connected the headphones, but now I can't have my phone 2 feet of the appliance without the music being agitated (bad connection).  I'm really irritated that I cannot understand this point and that he can't seem to find a fixed solution online.

  If you have just updated to iOS 9.3.4, which I didn't even know still shone, so maybe it's a bug that comes with the update. However, your problems seem to follow a trend, you can not far from a source of connection and now a signal. It is perhaps because the necessary components for the Bluetooth, GPS and WiFi signal are damaged or defective. Have you dropped or spilled liquid on your iPhone recently?