Vlan trunk between switches traffic encryption

Similar Questions

• VLAN Trunking between 6248 and 2848

  Hello

  I have a Powerconnect 6248 switch connected to a 2848 and I try to get a VLAN on the 2848.

  VLAN working and properly receive DHCP addresses, traffic lanes and DNS runs on the 6248.

  The Protocol DHCP, DNS server is connected to port 1 on the 6248.

  When I create a Trunk port on 3 the 6248 Port, allow all VLANS through it, creating a trunk on port 1 of the 2848 on VLAN10 and try to plug in devices inside, they can see all other devices connected to the L3 switch.

  The two switches are running the latest firmware and the L3 on his own works as expected. I can't get any kind of circuits working at L2, tried with normal cable and crossover switch.

  Here is the config of the L3 6248. Switch 2848 L2 has a blank canvas with 10 VLANS created on ports 1,2,3,4 with port 1 as the trunk port installation.

  Any ideas pleeease? Anyone? It drives me crazy.

  ************************

  <sub>! Current configuration:
  ! Description of the system "Powerconnect 6248, 3.2.0.7, VxWorks 6.5.
  ! Version of the software system 3.2.0.7
  ! Passage mode is configured as disabled
  !
  Configure
  database of VLAN
  VLAN 10,20,30
  VLAN 10 1 routing
  VLAN 20 2 routing
  VLAN 30 3 routing
  
  output
  battery
  1 2 Member
  output
  the IP 192.168.0.1 255.255.255.0
  field of IP domain name
  name-server IP 192.168.1.10
  IP routing
  interface vlan 10
  Routing
  IP 192.168.1.1 255.255.255.0
  output
  interface vlan 20
  Routing
  address 192.168.20.1 255.255.255.0
  IP helper-address is 192.168.1.10
  output
  interface vlan 30
  Routing
  192.168.30.1 IP address 255.255.255.0
  IP helper-address is 192.168.1.10
  output
  level password user name 'administrator' encrypted 15 5f4dcc3b5aa765d61d8327deb882cf99
  l2relay DHCP
  DHCP l2relay vlan 10-90
  !
  interface ethernet 1/g1
  switchport mode general
  pvid switchport General 10
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 10,20,30
  output
  !
  interface ethernet 1/g2
  switchport mode general
  pvid switchport General 10
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 10
  output
  !
  interface ethernet 1/g3
  switchport mode trunk
  switchport trunk allowed vlan add 10.20
  output
  !
  interface ethernet 1/g4
  switchport mode general
  pvid switchport General 10
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 10
  output
  !
  interface ethernet 1/g5
  switchport mode general
  pvid switchport General 10
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 10
  output
  !
  interface ethernet 1/g6
  switchport mode general
  switchport General pvid 20
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 20
  output
  !
  interface ethernet 1/g7
  switchport mode general
  switchport General pvid 20
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 20
  output
  !
  interface ethernet 1/g8
  switchport mode general
  switchport General pvid 20
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 20
  output
  !
  interface ethernet 1/g9
  switchport mode general
  switchport General pvid 30
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 30
  output
  !
  interface ethernet 1/g10
  switchport mode general
  switchport General pvid 30
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 30
  output</sub>

  After turning off spanning tree on the 2848, all works now.

  VLAN, trunking everything.

  Thanks for the help! :)

  I hope that if someone else can use what it took me ages to develop. I plugged on Netgear switches etc and they seem to work.

  The issue was going on between the dell 6248 and 2848, Spanning tree is enabled on the default 2848. If I was going to the Netgear via the 6248, then at the 2848 switches worked.

  My config on the l3 also works very well if someone would use :)

• Has anyone set up a trunk between switches PowerConnect 2716 and Intellinet 523554?

  I have a client who has three switches Intellinet 523554 in the core switches and various on the edge, including a PowerConnect 2716 switch. The firewall is a Sonicwall, which is plugged into one of the Intellinet switches, and there are three new SonicPoints that plug in the PowerConnect switch. To the best of my knowledge, even if X 0 (LAN) and X 2 (WLAN) are related to the SonicWall, I need to keep these separate networks. If I plug them both in the VLAN 1, network crashes (I presume due to a storm of broadcasting). On all switches, I created 2 VLANS, left 1 VLAN not identified and configured the appropriate access and if necessary junction ports. Two types of switches use the web-based configuration and it is just not a lot of parameters to be set. VLAN 1 traffic goes OK on the trunk, but VLAN 2 does not work. I'm not familiar with the configuration of the Intellinet switches, so I sent an email into their support. Unfortunately, for the chutes, that's what the rest of the world calls aggregation of links, so I have no help from them yet. I am quite confident that the configuration is as good as it can get.

  Has anyone else tried this and been successful? Any thoughts? The PowerConnect switch runs 1.0.1.07 firmware. Thank you

  The marking of VLAN is the feature you're looking for, 802. q. 1, Page 10 of the user guide describes in detail the configuration of VLANS on switches Intellinet.

  Assets.mhint.S3.amazonaws.com/.../523554_manual.pdf

  Page 50 of guide the user to the 2716

  FTP.Dell.com/.../PowerConnect-2716_User%27s%20Guide_en-US.pdf

  Hope this helps

• Trunk between SRW2048

  Hi all, I need to put a trunk between two SRW2048 connected via a fiber link, in order to leave a vlan to share between them.  My configuration is: switch A: - default untagged VLAN 1 - 10 of VLAN ID custom, named "wifi" - port 47-online fiber, defined as 'trunk', the two Vlan 1 and 10 are joined with the trunk - port 11: I want that he the VLAN 10, in order to see the 11 switch switch B: - by default without tag VLAN 1 - port custom VLAN ID 10 named "wifi" - port 48-online fiber, defined as 'trunk', the two Vlan 1 and 10 are joined with the trunk - port 11: I want the VLAN 10, to see the way 11 switch has tried to set the two port 11 mode "general", tag, joined only in VLAN 10, but I could not bind on the optical fiber. I tried many configurations for the two port 11, but they does not work. I think the 48 and 47 of fiber ports configurations are ok.  I hope you can help me thank you Alessandro Note:-yesterday I updated both firmwares to 1.2.2d; After that, I have an error in recording 'VLAN of Ports' setting on both switches. I check all the parameters. They seems ok, but this page (and only this) gives this error: line = 1 Type = unknown value = null value error diagnosis = may be lack of parameters (join1) in the page.  -I turned the 'enable 802. 1 x' flag on 'Security' => "' 802.1 x Settings"-I'm not using GVRP; " When I join the port to VLAN it gives me an error 'web' on Internet Explorer version 6 and 8, and I'm not able to reach the ports of vlan. On the other hand, I see the VLAN custom between switches only if I attach somethings to 11 ports (I use a dhcp server on one port and dhcp on another client).

  Only, I was struggling with today myself. That's what I had to do to get the VLAN on the trunk ports between SRW2048 and a SLM2024. Make the port numbers to the top, but you get the idea.

  SRW2048

  1-12 of Harbour = VLAN 1

  13-15 = port 3 VLAN, unidentified, mode = generally accept the type of weft = all, pvid 3

  40-43 = 2 port VLAN, unidentified, mode = generally accept the type of weft = all, pvid 2

  Port 47/48 = VLAN1, 2, 3 VLAN Trunk port = port should be vlan1, 2, 3 has joined to make you think it's the tag for 2.3 (check it, I'm 100% I added the and when I checked once again, they were gone.) "I think that changes to other environments will remove them?)

  SLM2024

  1-10 = VLAN 1

  14 = 3 VLAN, unidentified, mode = generally accept the type of weft = all, pvid 3

  16-18 = 2 VLANS, unidentified, mode = generally accept the frame type = alll, pvid 2

  12 (Trunk port) Add VLAN 1,2,3 with 2.3 tagged port

  Setup like that I could get access to all three VLANS on the trunk.

• Routing between two VLANs on a switch in series SG300

  I've seen a lot of messages from people with problems of traffic between the two routing VLANS with some complex examples.  Can someone show a simple example for a SG300 switch (in layer 3 mode) to set up the two VLAN and send the traffic between VLANS without an external router?

  VLAN1 10.10.10.0

  VLAN2 10.10.20.0

  I tried to do through the UI and can't seem to make it work.  It seems that it must be very simple, so maybe I'm missing something in the GUI.

  Hi Chris,

  I did 5 minutes of recording that showed how I configured the two VLAN on my SG300 switch and layer 3-switched between the VLANS.

  You have no trouble getting to the GUI, so you will have no difficulty to setup in a few minutes...

  • Be sure to use the latest version of the SG300 package, with a bearable CLI.
  • to save your changes to the configuration at the end of the process.
  • the IP addresses that you create will be the address of default gateway for PC hosts on VLANs specified.
  • Recording can be interrupted at any time to perform configuration operations.

  Recording is now available on the website of the WebEx service. Click on the link below to read:

  https://Cisco.WebEx.com/ciscosales/LSR.php?at=PB&SP=MC&rID=55688352&RKEY=05e1fc5fff0d05da

  Configuration of VLAN

  Monday, October 24, 2011 11:02 New York time

  5 minutes

  Have fun

  Best regards, Dave

• Having trouble getting the voice VLAN on the switch X1052P to work at all

  Can someone help me understand how to set up the voice VLAN X1052P? I spent several hours trying to get this working and it does not work. I spent about 4 hours on the phone with a Dell technician that night and he couldn't get it to work and finally gave up. He told me that I had to spend my warranty to ProSupport because he did not know how to solve the problem. What group of *. It's a simple configuration of VLAN. What must be so picky about? In any case...

  Setting up the VIRTUAL LAN must be fairly simple, but apparently on this switch is not. The user guide page 406 is not very useful except explaining what the different options. I must admit I am not an expert VLAN so I dunno I've misconfigured something. But remember, Dell technology could not operate either.

  Here's my situation... I have VoIP phones on my network connected to a network wall jack. Connected to phones are my computers of users. The computer of the user and its respective VoIP phone, both share the same data cable. Before replacing Cisco managed Internet service provider spend all it worked well. The problem is that they had direct access to our network so I removed the switch and installed the X1052P in its place. I talked to the ISP to let them know what I'm doing and they said everything I had to do was setup VLAN ID: 15 for the voice VLAN because this is the VLAN ID that the router uses to route telephone traffic. Router PSI is also the server DHCP VLAN 15 and issues IP for phones using 172.27.0.0/24 with a DHCP 172.27.0.50 range - 150.

  I tried to configure the switch using parameters of VLAN static and settings VLAN voice and neither one also seems to do what I want it to do.

  Network administration > VLAN > VLAN static

  Network administration > VLAN > Voice VLAN

  I activated the profile 'phone' on ports I want to added to the voice VLAN and it does not work. Moreover, 47 the switch port is connected directly to the ISP router and is configured as a trunk with the default port VLAN 1 unidentified and tag VLAN 15. For other ports I tried the general implementation, access and trunk of the parameters on each port to see if I could get something going and still nothing happens. When I set up the ports as General ports VLAN, I made adding VLAN VLAN 1 and VLAN 15 as a VLAN tagged not marked. It still does not.

  This is the short story from where I am now. Any help is greatly appreciated.

  FYI, as a follow up I finally solved the problem. I hope this information helps someone else that can encounter the same problem.

  After buying the ProSupport warranty upgrade ($121 out-of-Pocket mind you) and addressing a total of 4 technicians ProSupport expert technician a 3rd another level (only available via chat message between one of the ProSupport phone technicians and the 3rd Tier expert tech - i.e. I couldn't talk or chat with this person me) the consensus was that the material must be bad. When I bought the X1052P I bought two of them, so the best way to know if it was a bad switch was simply configure the other switch and see if the behavior occurs on this one, too. Well, this switch also restarted each time I assigned the profile 'phone' to more than 13 or 14 ports in the switch. It seems that it was not a hardware problem after all.

  I went back to the switch original and tried new things hoping that I could fall on a solution and it turns out that the solution was NOT to use the voice VLAN on the switch. It does not work!

  SOLUTION: I set the VLAN ID: 15 manually and no has not assigned any phone profiles to one of the ports. This is how I solved the problem.

  So he has bad software on the switch. I tried to see if there are updates of the firmware on the Dell support site, but there is none. Configure manually the phone VLAN was the solution. What a freaking nightmare which turned out to be. Maybe someone in Dell could note this problem and test in-house. And, if you want to compensate me for the 20 + hours I spent working on this problem, which has be great, too.

• N3048 vlan trunk band guaranteed bandwidth

  Hello

  Ive got 2 batteries of n3048 which will be connected by a link of fiber shds 1 Gbps, there are several local networks virtual on each stack and some of them I want trunk on the binding fiber.

  an of vlan is for a balanced load diversely routed internet connection, there is a router on each site with 100 Mbps bandwidth, but also firewalls at each site that will be in the same vlan.

  I don't want no internet to run slow because something is hogging the bandwidth on the shds, so the question is how can I guarantee 100 Mbps of traffic for vlan 10 through the shds with us other traffic crossing of vlan?

  I have install other powerconnect switches and switches cisco with trunking VLANs between switches but I've ever done where I need to ensure a slice of bandwidth with QOS?

  I'd appreciate any help or advice to achieve this

  Thank you very much

  Hi Daniel,.

  Sorry for the late reply its been a bit choppy on other projects so just had time to test this out.

  Here's what I ended up using in the config:

  Console (config) # class - match-all card VLAN_10_MATCH
  Console (config-WCPA) # match vlan 10

  Console (config) # VLAN_10_MARK policy-map on
  class console(config-Policy-classmap) # VLAN_10_MATCH
  Console(config-Policy-classmap) # brand cos 5

  Console (config) # int item in gi1/0/48
  Console (Config-if-X/Y/Z) # classofservice trust dot1p
  Console (Config-if-X/Y/Z) # classofservice dot1p-mapping 5 3
  Console (Config-if-X/Y/Z) # cos - min - bandwidth tail 0 0 10 0 0 0 0
  Console (Config-if-X/Y/Z) # cos - queue strict
  Console (Config-if-X/Y/Z) # - political service on VLAN_10_MARK

  I applied the same configuration for the trunk on two piles of switch port
  

  Thanks for your help in pointing me in the right direction

  I used jperf on 2 laptops in VLAN 10, 1 in each switch then your laptop on the other switch into a vlan with jperf mode server and 3 computers, send traffic using jperf him around the trunk and which seems to work well. ive tried run qos traffic vlan first and then maxing the bandwidth through the traffic trunk vlan qos not and then vice versa with traffic vlan qos to a already maxxed bandwidth through the trunk and he still gave him its bandwidth of 100 Mbps in both scenarios.

   

  concerning
  

• Cisco SLM224G VLAN Trunk Help! -&gt; Problem solved!

  Hi, I have a few difficulties of implementation of the switch, I can't understand how to configure the network for VLANs created port. I have configured under management of VLANS, VLAN 10 and 20, I asigned ports e1, e2, e3, e4, e5, e6 with 10 PVID and e7, e8, e9, e10, e11, e12 with 20 PVID and the rest to defaul 1 PVID, frame SD = All + infiltration on filtering. Under port to VLAN-> VLAN10-> ports e1, e2, e3, e4, e5, e6 Tagged + e24 tag (I want this to be the trunk) and the tag VLAN20-> e7, e8, e9, e10, e11, e12 Tagged + e24. Theats all that I set up according to the SLM_Admin_Guide.pdf and I have connected the e24 (trunk port) to a Pf meaning Server (the server is configured with the same VLAN ID as on the switch), please someone tell me how to set up the trunk? I know that there is no option in the Port settings to define 'Access' or 'Trunk'... until this means? that the SLM224G does not support the VLAN Trunk? I saw some screenshots with the Linksys SLM224G and he had 'Access' or 'Trunk' setting... and Cisco does NOT work.  Help!

  Hello

  Interesting, I see two different GUIs in your screen capture, it looks like two different computers. :-)

  But the big brother of the SLM, the series SRW and I am about what follows to the SRW series, because I do not have a SLM in front of me, I had put;

  Step 1. the port settings interface return, leaving the PVID to 1 then do scroll down and save the option.

  Step 2.  On this "ports setting photo GUI, you have, I would put the switch ports to shared resources in mode Trunk. If the port must not be tagged in the VLAN 1 only, then I leave the setting the port mode 'access '.

  (Access mode allows a port belong only to one VLAN no marked only).

  (shared mode allows the switch port belong to several VLANs marked, but still unmarked in one vlan only usually the vlan by default)

  Step 3.  So I goto the "Vlan to the port' tab, Tagged for ports beloning to vlan 10 then do scroll down and save the option."

  step 4   So I goto the "Vlan to the port' tab, Tagged for ports beloning to vlan 20 then do scroll down and save the option."

  By default vlan1 in most SRW series brother would then be not identified on all ports and vlan10 and vlan 20 could be labelled on the appropriate ports.

• The VLAN on a Switch Standard

  I am currently creating a new environment and we have a number of VLANS trunked together, I created a Standard switch for our virtual machine-to-machine network and the DMZ network, have each VLAN resources shared.

  What is the best way to do it?

  That I should...

  Create a vss and create groups of ports of individual virtual machine for each VLAN IDS? (for example, a switch for virtual machine VLANS and a switch to DMZ with groups of individual ports?)

  Or should I create just a switch for each with all 4095 active?

  Hey, as previously stated, the large traps with it would be the single points of failure, but since you're ok with it, I'm going to shut up

  Configuring VMware site seems ok, if you do not touch the vSwitches default security settings.

  Regarding the loss of connectivity, I am looking for the reason outside of VMware (VLAN not on two physical switch ports, bad IP/gateway settings within the operating system prompted, etc..)

• VLAN Trunking on vSS

  Hello

  I need trunk VLAN on vs.

  Say there are three VLAN 10,20 and 30.

  I am able to create the trunk on switch uplink physical, but not able to find out if how it should be done on vs.

  Kind regards

  Sushil

  To configure the VLAN Tagging, you can define a VLAN on a PortGroup.

  Let's say you want to have VM1 in VLAN 10, VM2 in VLAN 20 and VM3 in VLAN3.

  Then, you can create 3 exchanges each with different VLAN as screenshot below

  

  Connect to each appropriate virtual with PortGroup computer.

  There is not something like "switchport mode trunk" in vSwitch, simply configure a VLAN ID in the PortGroup.

  See this KB: VMware KB: VMware KB: example configuration of the virtual switch VLAN tagging (VST Mode)

• Start a Discussion on vSphere / VLAN Trunking in ESXi

  This is my first post to this community of VMware, so please bear with me if I'm missing something simple. I went to a discussion to ask this question under vSphere, but for some reason that I'm not able. I chose to follow the community of vSphere, but for some reason it is grey when I try to choose to start a discussion. Thoughts and guidance?

  The real question, I would like to ask on vSphere is how to configure trunking VLAN on a single host (no vCenter) using the vswitch standard. I find a lot of links like this one http://www.rustyhann.com/ESXi-06-Create-vLAN.pdf that describe the process of setting up a trunk on the switch port, then assign a VLAN ID to the ports on the ESXi host groups. When I change the switch to a trunk port, I lose conductivity to the host, so I can manage it is no longer. In addition, on the host, I see no VLAN ID and I don't see any configuration which leads me to believe that the switch is inform the host (thru VLAN Trunking Protocol or any other means) which have the VLAN. I might be able to answer this question for my part, I can bypass the first issue. Thoughts and guidance?

  Thank you. Best.

  Hello

  You are on the appropriate tab, just type 100 or 200 should you able to type value. Check out the screenshots below.

  

  

  

  

  

• Problem of BladeCenter ESX Server Vlan trunking

  VLAN for the ESX BladeCenter server problem

  ESX, Bladecenter, VLAN

  Hello

  The bladecenter was initially setup by a company and only allows me

  create a VM from Vlan 2. The problem is that I'm out of intellectual property that

  VLAN and I wanted the ability to use another address space for the

  VM I have already created a new vlan 20.

  This is the current configuration of the switch.  Everything I have added to these configurations to before was sw trunk allowed vlan add 20

  Switch CISCO 4500

  Interface Port - Channel 1

  switchport

  switchport trunk encapsulation dot1q

  switchport vlan trunk native 3

  switchport trunk allowed vlan 3: 1-20

  !

  !

  interface GigabitEthernet5/39

  Description Port Trunk BLADECENTER-sw2-p17

  switchport trunk encapsulation dot1q

  switchport vlan trunk native 3

  switchport trunk allowed vlan 3: 1-20

  channel-group mode 1 on

  !

  interface GigabitEthernet6/2

  Truck BLADECENTER-sw2-p17 Port Description

  switchport trunk encapsulation dot1q

  switchport vlan trunk native 3

  switchport trunk allowed vlan 3: 1-20

  channel-group mode 1 on

  !

  Config - sw1 Bladecenter switch

  VLAN 2

  Server

  VLAN 3

  WAN

  VLAN 20

  Server2

  Interface Port - Channel 1

  switchport vlan trunk native 3

  switchport trunk allowed vlan 3: 1-20

  interface GigabitEthernet0/17

  switchport vlan trunk native 3

  switchport trunk allowed vlan 3: 1-20

  Cisco-switch macro description

  channel-group mode 1 on

  !

  interface GigabitEthernet0/18

  switchport vlan trunk native 3

  switchport trunk allowed vlan 3: 1-20

  Cisco-switch macro description

  channel-group mode 1 on

  Blade switchport where the host is contained

  interface GigabitEthernet0/9

  Description blade9

  switchport vlan trunk native 2

  switchport trunk allowed vlan 2.20

  switchport mode trunk.

  The host ESX IP is in Vlan 2

  End result is that I can't use any VLANS in this new range.  There is no Vlan ID or installation marking.

  Thanks in advance.

  Grand...

  Don't forget to assign points for correct or helpful answers

• Problem with a SIP Trunk between VCS and CUCM

  Hello world

  I created a SIP Trunk between control VCS (X7.1) and a CUCM 8.6.

  I followed this Cisco_VCS_Cisco_Unified_Communications_Manager_Deployment_Guide_CUCM_6-1_7_8_and_X7 - 0.pdf deployment guide.

  The trunk is in place, but I have the following problem: I can ring since an EX90 recorded on the VCS for a registered on the CUCM 9951 but when I take the call, I have a busy signals (audio and video). When I on the EX90 9951 ring, I have the following message on VC: can not reach the contact.

  I have a 503 service unavailable status on the call history and "call rejected" on the event log.

  My transformation is OK and the call is sent to my neighbor CUCM zone

  You have an idea to solve this problem?

  Thanks for your help

  Best regards

  Bruno Z.

  Hello

  Yes, it's true! It seems at first glance a problem with codec negotiation when I see the reason 47 code.

  in any case set the region to G.711 trunk phone in case if you have different device pool and the trunk region and ip-phones.

  make G.711 end to end and test again.

  Thank you

  Alok

• What configuration of VLAN requires a switch connectivity defined as an access port?

  What configuration of VLAN requires a switch connectivity defined as an access port?

  By external switch tagging

• 802 1 q VLAN Trunking pilot

  Hello

  Refer to VMware ESX Server 3 802. 1 q VLAN Solutions (http://www.vmware.com/pdf/esx3_vlan_wp.pdf), the marking of comments of the VM mode (VGT), the document said about 802. 1 q VLAN trunking pilot use for the virtual machine. Can we know what it is and where to download?

  Kind regards

  Teeravee Sirinapasawasdee

  Never done it myself. Maybe this will help you

  http://www.lanarchitect.NET/articles/VLANTrunking/implementation/