VMware ESXi 4.0 startup screen Purple: 14 Exception PF world 9154?

Similar Questions

• VMware ESxi 5 Dump

  

  My unexpected server dump. Can someone help me solve this problem

  Hello

  This was caused by a virtual NETWORK adapter in your VM e1000 (e) - change to VMXNET3. See the following KB: KB VMware: VMware ESXi host 5.x undergoes a screen to diagnosis purple mentioning E1000PollRxRing and E1000DevRx

• VMWare Esxi 5.5 Core dump to disk

  Good afternoon!

  I am facing a problem in VMware esxi free 5.5.

  The server is crashing and showed a purple screen with the message "core dump to disk. Site 1 of 1... ».

  I searched on the problem but have not found a solution.

  We are the migration from VMware to XenServer.

  In my environment, I have a San with Equallogic PS4100.

  Can someone tell me what could happen?

  Image attached.

  Thank you.

  It seems that you are affected by this problem:

  http://KB.VMware.com/kb/2059053

  https://communities.VMware.com/message/2301745

  Unfortunately there is no patch for ESXi 5.5 still. The solution is to replace the vNIC e1000 in virtual machines with one another as the vmxnet3 vNIC.

• VMware esxi 4.1.0 Build U1 on HP Proliant DL 165 G7 348481 (590258-421) processor AMD Opteron 6128HE

  Hi all! I am new to vmware. I install VMware esxi 4.1.0 U1 Build 348481 on HP Proliant DL 165 of the G7 with an AMD Opteron 6128HE processor. Start after the installation of the server has been reset, vmware esxi, but after 5 minutes of work goes in the purple screen and work stoppages. If anyone has encountered this situation and can help me?

  No chance!

  Please note that the DL165 G7 is currently not supported by HP for VMware ESXi (only for ESX classic).

  See their Server ProLiant VMware Support Matrix and note (1) here for DL165 G7.

  You will find the same information in VMware HCL.

  Andreas

  - Blog of experience front of VMware

• BB10 Simulator on Vmware ESXi

  I'm trying to get the BB10 Simulator to work on a VMWare ESXi server. Here's what I've done so far:

  1. Installed the Simulator on yhe development machine, started VMWare workstation, open the vmx file and downloaded the VM on the ESXi server.
  2. Disabled 3D acceleration on the machine virtual (on ESX) and selected 'Full touch safe mode' after starting the virtual machine.

  At this point, the virtual computer screen displays the IP 'telnet ftp ssh qconn', the axis of the device and the build number.

  The next step is to connect the Momentics IDE to this virtual machine.

  The Simulator is in need of a vmx file configuration dialog box (likely to run vmware specific commands). In the configuration of ESXi, there is no vmx file.

  If I try to connect to the virtual machine by IP address, I need a device password, I did not.

  Someone at - it suggestions on what do I do now?

  In response to my own question because I found the answer:

  Now that I have the IP address, I just follow the steps described in

  http://supportforums.BlackBerry.com/T5/native-development/BB10-native-Cascades-SDK-not-connecting-to...

  Because I had never set up a password for the Simulator, I left the empty password field.

  Copy-paste the details:

  Of your IDE

  -Right click on your project in the Project Explorer

  -Go to Blackberry tools and click on configure target...

  -Click Add new target it... button and enter the IP address of your Simulator in the host name or IP address field, enter your password if you have one then click on finish

  To run your application on the Simulator:

  -In the Project Explorer view, double click on file bar - descriptor.xml, then click on chip Debug Set button to set the author of the application information.

  -Set the configuration of the correct version for the Simulator first by right-clicking on your project and selecting Configurations of Build > Set Active > 4 Simulator-Debug.

  -In the Project Explorer view, right-click the project and select build project.

  -Right click on the project again, and then select run as > BlackBerry Application C/C++.

• Problem with the start of VMware ESXi 5.0

  I just installed VMware ESXi 5.0 on a new Cisco UCS B200 series blade with two 300 GB hard drives configured in a RAID 1 mirror.  I went through and completed the installation of VMware ESXi 5.0 on this server.  When the installation is complete and the server restarted, he did not initiate the ESXi where I can change the IP address and VLAN.  Instead, I get this text string after the initial boot sequence that is shown in the attachment.  I have a guest who said Shell > do not know why I can not start correctly in ESXi 5.0.  Thank you!  Paul

  Hi Paul,.

  Looks like you boot to the EFI shell. What is the startup policy that you have configured on this server service profile? It should look like the one below.  If there is a problem with the boot order, you should be able to type "EXIT", then enter on the EFI shell to exit the prompt. If your startup is similar to the one below and you still experience this issue, try to downgrade and re - ack the blade.

  Let me know if it helps.

  

• OpenManage for VMWare ESXi has no possibility of tasks of virtual disk

  OMSA v 7.1 and 7.2 for Windows (and earlier versions) allow the user to perform many tasks on virtual disks, including reconfiguring - expand a RAID array with a new drive.

  This is not true for managing open for VMWare ESXi - although you can monitor the status of the RAID and disks with the browser of the OMSA interface type, you cannot perform tasks - can not even make a high beam Flash.

  It is a huge problem, because the PERC controllers (H700 and H800, for example) don't allow you to develop virtual using hard drives not Dell disks when you try this during startup in the bios.  (These controllers only allows you to create new virtual disks using drives not Dell).

  This test was conducted using the latest firmware (12.10.4 - 0001 A10) and drivers for the H700 and H800 and multi-server r610 ESXi 5.1.

  Other people with VMWare have been affected by the present?  The only solution is to have two player networks connected to the computer, and create a simple Windows with OMSA, boot in Windows Server to expand the table using OMSA for Windows.

  I would be interested in the comments of others, including those of Dell.  We spent hours on the phone with Dell; This seems to be the only solution.  (Yes, Dell released a firmware version last year that has ceased blocking non Dell readers, but it only works for the creation of a new virtual disk, do not expanding one existing).

  Yes.  It came through a discussion in the Dell | Servers | Discussion of the RAID community.

  en.Community.Dell.com/.../20263442.aspx

  There is a CD bootable linux called OMSA Live that you download from PowerEdge (linux OS) systems management.

  This OMSA PERC H700 and H800 control and allows you to do everything.  When you reconfigure the RAID and the PERC card starts the reconstruction, although it seems risky, you can restart under VMware and the reconstruction of the RAID continues on.  And you can analyze with OMSA for VMware.

• Install VMware ESXI 5.1: GROUP with no error reported

  Hey everybody,

  We are trying to install VMware on a server which seems full fill all the requirements of the material.

  We have tried both a CD and a USB key (who both successful install VMware on another server)

  and we had this problem:

  A few seconds after that, we started from the Flash DRIVE or the CD, we get a simple screen purple

  with absolutely no message and no error reported. Then, if we expect more, we get a black screen with a few

  green squares arranged randomly all over the screen.

  If someone who had the same problem could help us or if anyone has an idea on how

  to get some kind of error there reports, it would be very apreciated!

  Thx for your time and your consideration buddies.

  Please tell us what the hardware. Also please download and apply the latest firmware available for this material to the web site of the manufacturer. I had the exact same problem with my HP DL360 Gen7 and I applied the last Pack of Proliant HP who has paid the GROUP for me.

• Drive HARD physics add to VMware ESXi 5.1

  I came across a configuration of a Dell Power Edge ii one T110 Server VMware ESXi 5.1

  
  

  It was built not by me, I found it here. I came across the need to increase the storage of VMware, but I need to add a new physical HARD disk.

  
  

  I'm afraid to make any changes to the system, because there is no backup found for the virtual machine.

  
  

  If I stop the physical machine and connect the additional HARD disk, how can I declare to the VMware, in order to define the backup of the virtual machine?

  
  

  Thank you in advance.

  
  

  Sincerely, George I.
  

  When you restart the server, you should see an option to create a matrix of storage before the ESXi begins to start up (this option is available for almost all servers and appears between POST process and startup). Select the option and create a RAID 0 array on second HARD drive. Start the ESXi server after that. You have to be sure that the second HDD is not in use or it will be formatted.

  When the ESXi has started, go to Configuration-> Storage-> rescan all. After the news of the analysis is complete, go to storage add and you should see the table that you just created. After you have added storage, it will be visible as a the ESXi data store.

  Let me know how it went.

  Elodie

• VMWare ESXi is not responding

  Hello
  
  I have a server at home with a Q6600 Quad Core and 8 GB RAM running with VMWare ESXi 3.5 for about 8 months now. I have 2 warehouses of data, with 1 TB (SATA HDs), each with 150 GB free and the other with 240 GB free. I have 9 virtual machines running 24 x 7 on it. Everything has been done, until yesterday.
  
  Out of the blues, I stopped to get the answers from the MV in the ESXi. Initially, I was able to connect using the Client Infrastructure but, when if I tried to get information from any virtual computer, I receive a message that the virtual machine could not be reached. Looking at the info from the host, he would show me info network, cpu, memory, but when I tried to reach the data store, it would normally stop responding. I couldn't open the located data store where ESXi is installed once, and all virtual machines were there. Now, I can not connect more, and I don't really know what to do.
  
  What is the best course of action to diagnose the problem? I can access the ESXi screen without problem, but I don't know what to do. I thought to reinstall, maybe with version 4.0, but I'm not sure I should do it. Where (and how) can I access what anyone who could help me figure what's wrong?
  

  TKS

  Try these options in the following order:

  1 reset the Management Agents: http://pubs.vmware.com/vsp40u1_i/wwhelp/wwhimpl/js/html/wwhelp.htm#href=setup/t_restart_mgmt_net.html

  2. restart Management Network: http://pubs.vmware.com/vsp40u1_i/wwhelp/wwhimpl/js/html/wwhelp.htm#href=setup/t_restart_mgmt_net2.html

  3. restore the vSwitch standard: http://pubs.vmware.com/vsp40u1_i/wwhelp/wwhimpl/js/html/wwhelp.htm#href=setup/t_restore_stnd_switch.html

  4. full reset: you loose all the configurations you made on the ESXi server, but the guests are kept.

  http://pubs.VMware.com/vsp40u1_i/wwhelp/wwhimpl/js/html/wwhelp.htm#href=Setup/t_reset_the_configuration_defaults.html

  AWo

  VCP 3 & 4

  \[:o]===\[o:]

  = You want to have this ad as a ringtone on your mobile phone? =

  = Send 'Assignment' to 911 for only $999999,99! =

• VMware ESXi HA and DNS

  I am currently evaluating VMware on a set of blades with ESXi. I set up a pair of network cards to form the management network and activated VMotion on them. VMotion works very well between guests both manually and with DRS.

  However I'm not sure how do I configure HA, trying to turn on HA my cluster test fails because the hostname and IP do not match. The dedicated management network is not a DNS server because it is just the blades and chassis switches. I manually assigned each blades management IP through the ESXi set up the screen on each physical host.

  • Is there any reason HA cannot use IP addresses?

  • If I have to use for the name resolution, these configurable in/etc/hosts using ESXi?

  I have attached a screenshot showing the network configuration of one of my hosts (VMotion is enabled on the "management network").

  If you have experience with a similar set to the top it would be much appreciated.

  Thank you

  Will be

  You must place the FQDM and IP address of all ESX servers in the cluster in the file on each ESX host:

  1. Do not remove the next line, or various programs

  2. who require network functionality will fail.

  127.0.0.1 localhost.localdomain localhost

  SERVER NAME SERVER IP ADDRESS

  SERVER IP ADDRESS THE SERVER FQDN

  for example

  192.168.1.12 monserveur.masociete.com

  If you found this information useful, please consider awarding points to 'Correct' or 'useful '. Thank you!

• Pavilion dv7t-3000 mobile: stuck on the startup screen, must repeatedly perform a hard reset to fix

  When starting after a successful boot & use, the PC is stuck on the startup screen that is black with the logo blue & white HP in the middle and "press ESC for the start menu" at the bottom left. I have to perform a hard reset to get a normal startup. Everything works fine. I stop the PC from the start menu. At the next startup the PC hangs at the HP splash screen. A hard reset solves the problem, but the problem occurred on & repeatedly.

  Problem was solved by uninstalling a number of HP programs! Unfortunately I have lost the paper on which I wrote exactly what programs I uninstalled. If you find this issue that may arise on your notrbook, try to uninstall the HP programs

• Laptop freezes on Windows startup screen (start)

  Freezes my laptop Envy15-3000 starting up.  It makes only to the Windows startup screen and then icons Microsoft stop moving.  This has happened since Tuesday (8/12).  I ran checks and the memory and hard drive (quick and full) test came back positive - i.e. without problems.  I finally decided to reformat yesterday (8/14).  He gets throughout the process of reformating until he wants to start the system for the "first time" (I guess this will be the last time it restarts in the recovery process) and always freezes on Windows startup screen.  If I try to hard cock off and try any other start up option I can think (Safe Mode, etc.), it says failed to retrieve and asks me to try again, get the details or Save Log.  When I try again, it goes back to freezing.  Therefore, I am now in an endless loop of another attempt of the retrieve to access the windows screen start freezing.

  All I want to do is wipe the hard drive and reload everything.  I'm not interested to recover the old data I backed everything up.  I have had no error messages on my sleeve it, memory, tests etc, so I'm at a loss on how to proceed.  Help, please!  Thank you.

  PS: I have the original 7 provided with the system recovery/windows DVD player.

  Hello

  Assuming that it's just a problem with the recovery media, here's another solution, you can try.

  Before you try the following, make sure that you can always read the character product activation key 25 on your label Windows COA (5 blocks of 5 alphanumeric games).

  An example of a COA label can be seen here.

  You can create a Windows 7 installation disc yourself using another PC - just download the Disk Image correct ( this must be the same version that originally came with your laptop - it is listed as Windows 7 Home Premium ) from the link below and use an app like ImgBurn ( Note: you can deselect additional software offerings when you install ImgBurn) to burn the ISO correctly on a blank DVD - a guide on the use of ImgBurn to write an ISO on a disc is here.  The source of the Windows Image is Digital River.

  Windows 7 Home Premium 64 bit SP1.

  Use the disk to perform the installation, enter the activation key of Windows on the label of the COA at the request and once the installation is complete, use ' 'phone Method' described in detail in the link below to activate the operating system -this made method supported by Microsoft and is popular with people who want to just have a new installation of Windows 7 without additional software load normally comes with OEM installations.

  http://www.kodyaz.com/articles/how-to-activate-Windows-7-by-phone.aspx

  All pilots additional and software that you may need are entering either the No. fullModel. or your notebook product number here.

  Kind regards

  DP - K

• just loading at startup screen but after loading is the screen is completely blank.

  original title: help with a Windows Vista laptop please help.

  When I start my HP Windows Vista laptop, it works very well and just loading at startup screen but after loading is the screen is completely empty. The keyboard works fine and the keyboard lights are on but nothing on the monitor. Help, please? Passing on the black screen the arrow appears, but again, it is all black.

  > @dhhuang they don't tell me because I have no guarantee and it's like over $ 100 just for talking on their phone, which I think is not worth.

  I'm sure you can order a set of recovery disks. You need to talk to a technician to do it. Yes?

• Upgrade VMware ESXi 6.0 Update 2 VMware ESXi 6.0

  Hello I am running my PowerEdge T110 II with VMware ESXi 6.0 - Dell customized image. I see that from April 15, 2016 Dell just introduced VMware ESXi 6.0 Update 2 and I'd like to update my system.

  On the download page , I see there is an option to download and the ISO file. I wonder if this installation will completely be wipeout my existing VMware ESXi 6.0 - Dell custom and all the settings and I have to start all over again or update 2 ISO just 'modernize' my network?

  Hello

  You can use it to update without doing a new install. KB.VMware.com/.../Search.do; cmd = displayKC & externalId = 2109711 #Inter