volts/meter

Similar Questions

• High level electromagnetic Satellite R830 show

  I wonder if some users have never measured the residual electromagnetic field on the keyboard of the laptop Toshiba satellite R830.

  If the laptop is connected to the battery charger the residual electromagnetic field is about 10-12 volts/meter! This value is very high and can be dangerous for hands and skin in general.

  I did this test, because all the time I answer the phone and the laptop was near the phone and connected to the battery charger, I hear a noise in telephone communication.
  I decided to measure the electric field with an appropriate field meter and the result was about 10 V/m.

  I'm very worried about it. Can you please tell me if you have any news on this issue?
  I also invite you to one of the Toshiba EMI staff in the discussion.

  Thank you very much

  Antonio

  AFAIK all units are marked by the CE.
  Manufacturers of products with the CE marking, declares that the product complies with the essential requirements of the applicable directive.

• My Satellite phone (A305) stops operating on the sector/charger adapter

  The problem is that my Toshiba laptop series _A300 (A305) stops when you try to run on the Charger AC/adapter_. You can start with the power cord plugged in and it goes to the Windows desktop and maybe a few more minutes to the maximum before turning off.

  It will start and battery without problem_ _run, but if you plug the AC while it is in place and running on machine battery will normally DESACT instantly and restart to the message "Windows has been shut down properly."

  The adapter _AC works fine_ reading a 19.19 to 19.20 stable volts with a volt meter. He also _charges battery very well when the computer is ignored. I have two Toshiba brand batteries, and both work very well.

  An interesting thing is that the _computer works well on AC if safe mode_.

  I _did a restore_ of reformat/factory of Vista to ensure it was not software and drivers and still had the same problem before external devices had been plugged.

  It has the latest version of the BIOS and I tried to reset the values by default where something had changed. It made no difference.

  This is _not an issue_ of heating because _while it works on battery I can watch long videos_ without it cutting. I ran the air through the vents in order to ensure, but it makes no difference in behavior. Usually with overheating stop, the computer cannot be started until it has cooled some, but these cases are accompanied by Instant reboot.

  I saw on a few discussions that this type of problem, you can work around by disabling one of the processors in the Device Manager, but I don't think it is a big part of a sustainable solution or for the computer.

  Has anyone seen this problem before and you come up with a complete diagnosis of the problem and a real solution?

  I have the Satellite A300 and so far everything works OK.

  I would like to know what happens when you remove the battery and use the laptop with power supply only. Done laptop stops again.

  If this is not the case, leave the BONES run and put the battery.
  The battery is correctly recognized? Laptop turned off again?

  To be honest, I can't imagine that this question has something with the software or background process. Recovery image, that you got with your laptop is designed for this specific laptop mode. Recovery image has been tested and I don t think preinstalled OS has nothing to do with it.

  Complete diagnosis?
  And how to proceed? You know very well that the diagnosis can only be done with diagnostic tools, and these tools have only services. I hope that you find some answers but I m 99% there is nothing you can do about it. Maybe you should communicate with the service, explain the situation and ask for help.

• Program LabVIEW will hang between 33% and 50% of the time.

  I have a problem with a Labview program, I did. I have two programs that do the same thing. One is as a flat sequence, and the other is in the form of State machine.

  As explained in the link below, I would like to use a microcontroller to perform wiring for automation of a measurement process. A separate current source and volt meter will be used.

  https://forums.NI.com/T5/LabVIEW/sequence-a-good-idea/TD-p/2601333

  I did some simple test programs that I join since then. The problem is when running, that the labview program crashes, but not all the time is to run the program.

  For example: Hall 1.2.vi will correctly work twice with the third time, he is executed, it crashes. If Cancel you and try again, it will run again twice without any problem with the third hanging. It is in the flat sequence format (was in a flat sequence, but merged windows because I thought that was the cause). From what I can tell, the program crashes when calling Keithley 6517 unique Read.vi. Two connected Keithley devices are connected to the computer via GPIB to 16 and 27. The way I checked if it was this vi the cause or contributed to what I deleted the program never hung and it. I find it very strange that it crashes exactly on the third attempt every time.

  Simple.VI Hall 1.3 will work the first time and hang the second time. If it works 50% of the time. It is in the format of State Machine. It hangs in the case entitled "Measurement 1" that contains the Keithley 6517 unique Read.vi.

  I used the running highlight button and watched the program to run. Curiously, it only crashes when you use this button. So I tried to add some delays/waiting in different places without success.

  This could be the cause? As a side note, I say that the program is suspended for two reasons. The principal is the program does not run so the execution arrow is always black. The second thing is that if you notice at the end of the labview program, I have a block he who turns to the power source which does not happen when it crashes. I have to turn it off manually, and then click the abort program button to stop labview.

  
  

• What is READ the array returned by the DAQmx meter? How can I know the two functions DAQmx READ data stream in the same WHILE loop?

  I have a question about the order of execution.  In the WHILE loop, I have two things to measure, period and tension using the DAQmx READ functions for voltage and the meter.  In the end, I want to collect these data as points almost simultaneously as possible, as a pair and then send them together to another piece of code (not shown here) which them will result in some sort of command for an engine.  It would be run, and then I want to perceive the tension and the period at a time later and do the same thing.

  (1.) I'm a little confused on what the meter of the READ function is back because it's a table.  What is a picture of?  I thought that it was up to the value of the individual periods between rising edges.  The output of the counter 1 DBL d's a table. How many elements in this table, and what determines the size of this table?  Are the elements of the array the individual delays between the edges?  How many values are stored in the array by executing?   We take the AVERAGE of the last 15 items, but do not know if we are throwing some of the data or what.  How to understand the composition of this painting?  How can I change the composition of this painting?  Is it possible to measure only one period at a time, for example the time between TWO edges?

  2.) Will this WHILE loop execute as it gathers tension and a "period table ' (remains to be understood by me) by TIME running in a loop?  In particular, we want that the value of the tension associated with the value of the AVERAGE of the period "array", so we can use two data items to create orders of next control every time that the two values are reported.  The structure for the delivery of vi will be attached data in pairs like this?  I understand that one of the READING functions run not before the other function of READING in the WHILE loop.  I want that the period "means" and "strain (Volt) collected at the same pace. This vi will he?

  Thank you

  Dave

  Hi David,

  I suggest including the DAQmx Start Task function. If it does not start before the loop, it starts the loop and work very well, but it is not as fast and efficient. In the model of task status, task wiill go to run the checked each iteration of the loop and then back the time checked running when it restarts.

  The status of the task model: http://zone.ni.com/reference/en-XX/help/370466V-01/mxcncpts/taskstatemodel/

  Kind regards

  Jason D

  Technical sales engineer

  National Instruments

• Meter output that uses as AO start

  Hello everyone,

  I am currently using a PCI-6120 with a BNC-2120. In VI I have attached to this post, I have an analog output channel that generates a predefined signal stored in the memory of the Commission. Regeneration is activated so that the signal is emitted continuously.

  The generation can be stopped and (re-) started at any time using a switch on the front panel.

  Outside this AO channel, there is a counter. I would use this counter as the trigger to start for the AO, so that, when the switch on the front panel is set on WE, the AO task waits for the next rising edge of meter output to start the build.

  Here's my problem.

  When I run the VI, the first beginning of the AO is in fact triggered by the meter. The two generated signals are perfectly synchronized (AO and Ctr). BUT! After putting the switch to OFF and then back on, the signals are not synchronized more. AO task starts generating right samples after the start of the task, without waiting for the next rising edge of the output of the counter.

  Could someone help me understand what is happening, please?

  Why it works just after the execution of the VI, but not after using the switch on the front panel?

  Thank you very much.

  P.S.: when the switch is off, the AO job is not completely stopped. The OD begins to generate a constant value of 0 Volt. It's normal. I want to check the value generated by the Board at any time to avoid damage to the unit that I send the signal. So I force the generation 0 Volt, rather than simply stop the task.

  LucG,

  According to the S-series user's Guide, the time will be two impulses of your time base clock sample. So, it is expected.

  The delay of the 2 tick must be for an internal sample clock. There should be no delay if you use an external sample clock.

  You can check whether this delay appears when the sample clock is also used as the trigger for the start. I didn't realize this test.

  If it doesn't, I think that your solution will be to buy another Board because I have already spent time yesterday to try something else like using the counter of seconds for example, but it really seems that there is no work around except buy a Board with a more recent technology.

  Kind regards

• monitor the iMac 27 grips 2011 TR spegne meta

  Da few week ago it monitor del mio iMac 27 grips (meta 2011) if spegne come in questo video.
  Ho tried AHT my non riesco a farlo partire. PREMO D d led computer my dopo circa 30 secondi in cui remains schermata bianca if starts usually.
  Rate Cosa Può if?

  FA questo lavoro a tutti?

  Bootup tenendo CMD + R, o it looping option / alt by the d dalla partition di ripristino e utilizzare utility Disco da li disco he riparare, quindi su Ripara years.

• Iphone5 is compatible with JIO 4 G Volte?

  Iphone5 is compatible with JIO 4 G Volte?

  Hello Santosh.Nalluri!

  I certainly want to check the compatibility of my iPhone with other networks. We can see what is happening here.

  Start by looking at this document on LTE and iPhone: Apple iPhone - country view with support for LTE networks -

  JIO is not listed for use with the iPhone 5.  Therefore, it is unlikely that this works on this network.  You can check with the carrier for them to confirm this, too.

  See you soon.

• Create a table of values for which a condition is met

  I have exactly this problem, however connected solution is no longer valid: Re: table to automatically generate values if the condition is met,

  Basically I have a table (named 'Master Sheet') that has two columns, one with project names with a status ('Active' or 'pending'). I want a separate table that automatically fills the project names of the leaf of the master for which the status is 'Active '.

  For example, from this table:

  Project	Status
  Red	PENDING
  Orange	ASSETS
  Yellow	ASSETS
  Green	ASSETS
  Blue	PENDING

  I want to automatically generate this table, which contains only values whose status is 'Active' (not 'pending' and without values null):

  Project	Status
  Orange	ASSETS
  Yellow	ASSETS
  Green	ASSETS

  Please note that using the filter function does not work in this case, as I need to be able to freely add new lines to the two tables.

  Hi Kath,

  Here is a pair of similar solutions.

  

  That on background uses a writing ('ACTIVE') of the value in the formula in the master-1 table to create the index in column C.

  Above who gets the value of the cell in row 1 (A1) of the table of the single column and lists him only the names of any State were brought to the project.

  Index columns can be hidden.

  Formulas:

  Master: C2 IF (B = C$ 1, ROW (), 999)

  Table 1::A3: IF (SMALL (Master: $C, LINE () −2) = MAX (Master: $C),"", INDEX (Master: $A:$ B, SMALL (Maste r: $C, ROW (−2)), COLUMN ()))

  Master - 1:C2: IF (B = "ACTIVE", ROW (), 999)

  Table 1 - 1:A2: IF (SMALL ("Master-1': C, LINE (−1) ') = MAX ('Master-1': C),' ', index (" Master-1': b, SMA LL('Master-1'::C,ROW()−1),COLUMN()))) ")")

  All forms filled up to the last line of their respective columns.

  Filled with formulas in column A of the table of two columns to right of column B.

  Single column table must be no more than a longer column of its master table.

  Double table column must be as long as his master table or less.

  Kind regards

  Barry

• Battery meter

  My iPhone 6 is running iOS 9.3.1 just today started having a problem with the battery meter records does not correctly. After several hours of using my phone this morning, I noticed that he was always at 100% and he died soon after. It wasn't a problem last night, because I remember watching down to 4% and die last night. I had my time manually rather than what allows it to configure automatically. This http://fortune.com/2016/01/19/battery-issues-iphone-6s-and-6s-plus/ of fortune dot com suggested to do a hard reboot and automatic time setting enable. I restarted, and then activated, then restarted again, but nothing.

  I got the iOS version that I am running for awhile, so I don't think that it has nothing to do with the update because I only started to have a problem with it this morning

  First, download the autonomy since the app store app. It will tell you the status of the battery. Then try the battery meter calibration if the problem is not the battery.

  Recalibrate your battery meter:

  • Charges to 100%
  • Run the battery until the phone turns off
  • If it stops above 1% charge for only one minute, and then continue running the battery down. Repeat until it makes 1% before shutting
  • Load it back to 100%

  If the battery is defective, this should fix it.

• I have 3rd gen apple tv does work on input 220-240 volts

  Hello

  I have 3rd gen apple tv does work on input 220-240 volts

  Yes, where the TV was purchased?

  You might need a pin adapter.

• Can I charge my IPad 3 G safely on 240 volts in Europe (Israel)

  How my 3 G IPad are safely attributable on 240 volts while in Europe (Israel)?

  If you use the Apple adapter supplied, Yes.

• How to reset meter reading in iTunes 12.4?

  After the update, I am unable to reset the account play someone knows a work around or how to reset the meter reading?

  Here's a short AppleScript to replace the missing functionality of time reset. In addition, it erases all jumps, or position of bookmark and the last played and jumped dates.

  Copy and paste into the script editor, save it as LastPlayedNever in ~/Library/iTunes/Scripts. Select one or more tracks and call the script in the scripts menu in iTunes.

  

  -LastPlayedNever - v1. 0 - © Steve Maguire - 2016-05-18

  say application "iTunes."

  If the selection is not {} then

  set mySelection to selection

  Repeat with aTrack in mySelection

  the value played County of aTrack to 0

  the value played date of aTrack to missing value

  the value ignored County of aTrack to 0

  the value ignored date of aTrack to missing value

  If aTrack is bookmarkable then set bookmark of aTrack to 0

  end Repeat

  end if

  end say

  
  

  
  

  TT2

• Why does not the meter of the quality of one of my choices of master password, regardless how I mix letters, numbers and non-alphanumeriques characters?

  I tried to create a master password, but it couldn't be done because the quality meter never accepted none of my passwords, even if I used a mixture of very complicated letters, numbers and special characters as well.

  There is no requirement when setting master password in Firefox. The password quality indicator is purely informative.

  If you try to fill the bar all the way, that's unlikely, unless you create a long password, or a mixture very complex of special characters, upper and lower case letters and numbers. Don't forget the password should be easy to remember and typed in, time after time. A highly secure password that is easily misspelled or forgotten is of no use.

• The CPU meter on the dysfunctions of transport bar

  At the far right of the Transport bar is a CPU meter. When a project is first opened on LPX, this gauge is the most crazy. It takes about 30 to 60 seconds and sometimes more. During this time, I am unable to play any project - the sound stutters. There is nothing I've been able to do to eliminate (or same gear up) this anomaly.

  (a) what could be the cause?

  (b) how could this problem be solved?

  Thank you

  It's perfectly normal: your content (sampled instruments, inflected tracks, audio files) is loaded into the RAM disk, using all available CPU power. The only thing that you can "do" is less sample content or less flexed titles. Or simply wait 30 to 60 seconds.

  I sometimes play a project that takes over again, but that's useless, the project will stutter and he will miss notes instrumentsa who are not entirely responsible.

  It may also take longer if you have other applications open (webbrowsers) because the contents of the RAM may need to be swapped to and from the disk.

  Opening & downloading a project of average size (with an already high logic) just took me 1'25 "."

  Two more $ to speed up: increase the RAM or use SSD (s) to store your recording and storage of the content of the sample.