VPN clients are unable to access internal resources
Hello
I have problems with internal resources from access to the content of VPN Clients. They connect using Cisco VPN Client, they connect correctly, an IP address from the correct range is given and I ping to the internal server, but any other type of access as Server terminal server. Ping to server ip from the inside is answered by interface router public ip instead of the internal server and I don't know if it's this way. There isn't any ACL applied.
Crypto ipsec debugging I see this error when I do the server terminal server:
% CRYPTO-4-RECVD_PKT_NOT_IPSEC: Rec'd package not an IPSEC packet. (ip) vrf/adr_dest = / public-ip, src_addr = 172.16.73.4, prot = 6
Here is the configuration associated with vpn:
crypto ISAKMP policy 10
BA aes 256
preshared authentication
Group 2
!
Configuration group customer isakmp crypto VPN_Clients
Cisco key
DNS 4.2.2.2
pool - vpn clients
ACL 101
netmask 255.255.255.0
!
!
Crypto ipsec transform-set RIGHT aes - esp esp-sha-hmac
!
Crypto-map dynamic dynmap 10
Set transform-set RIGHT
market arriere-route
!
!
card crypto mymap client authentication list userlist
Group card crypto mymap isakmp authorization list
client configuration address map mymap crypto initiate
client configuration address map mymap crypto answer
map mymap 10-isakmp ipsec crypto dynamic dynmap
!
!
! Gateway for the default internal resources
interface Vlan72
IP 172.16.72.1 255.255.255.0
no ip proxy-arp
IP nat inside
IP virtual-reassembly
!
Kind regards.
VPN client IP local pool 172.16.73.2 172.16.73.10
!
!
interface Dialer1
the negotiated IP address
IP mtu 1492
NAT outside IP
IP virtual-reassembly
encapsulation ppp
Dialer pool 1
Dialer-Group 1
Authentication callin PPP chap Protocol
PPP chap hostname XXXXX
PPP chap password 7 XXXXXXXX
accept dns ipcp PPP
PPP ipcp address accept
No cdp enable
crypto mymap map
access-list 101 permit ip 172.16.72.0 0.0.0.255 any
!
Hi Anotino,
Problem seems to be with the NAT configuration on the router. The NAT config is now below:
access-list 1 permit 172.16.72.0 0.0.0.255
NAT_WAN1 allowed 10 route map
corresponds to the ip address 1
match interface Dialer1
IP nat inside source overload map route NAT_WAN1 interface Dialer1
We need to change it to look like this:
access-list 100 deny ip 172.16.72.0 0.0.0.255 172.16.73.0 0.0.0.255
access-list 100 permit ip 172.16.72.0 0.0.0.255 any
NAT_WAN1 allowed 10 route map
corresponds to the IP 100
IP nat inside source overload map route NAT_WAN1 interface Dialer1
This should make sure to go to the pool of clients VPN traffic United Nations concerns and therefore, you should be able to access the network using the private IP (172.16.72.2 for example).
Try this and tell me if this solves your problem.
Kind regards
Assia
Post edited by: Assia Ramamoorthy small correction in the post!
Tags: Cisco Security
Similar Questions
-
VPN clients are unable to access sites that are above a link from site to site
could someone please give me some direction, I have a set of vpn clients set up on a pix and I'm trying to give them access to a network that is connected via a link from a site that is set up on the same pix. so, basically, that it receives information from VPN client on the same interface, it built the tunnel from site to site, I've heard that's not possible is that the case. Or it can be fixed, I can provide diagrams and if necessary conf files.
You are right. You need a minimum of 7.0 for the feature you're looking for.
Kind regards
Arul
* Please note all useful messages *.
-
remote VPN and vpn site to site vpn remote users unable to access the local network
As per below config remote vpn and vpn site to site vpn remote users unable to access the local network please suggest me a required config
The local 192.168.215.4 not able ping server IP this server connectivity remote vpn works fine but not able to ping to the local network vpn users.
ASA Version 8.2 (2)
!
host name
domain kunchevrolet
activate r8xwsBuKsSP7kABz encrypted password
r8xwsBuKsSP7kABz encrypted passwd
names of
!
interface Ethernet0/0
nameif outside
security-level 0
PPPoE client vpdn group dataone
IP address pppoe
!
interface Ethernet0/1
nameif inside
security-level 50
IP 192.168.215.2 255.255.255.0
!
interface Ethernet0/2
nameif Internet
security-level 0
IP address dhcp setroute
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
Shutdown
No nameif
no level of security
no ip address
management only
!
passive FTP mode
clock timezone IST 5 30
DNS server-group DefaultDNS
domain kunchevrolet
permit same-security-traffic intra-interface
object-group network GM-DC-VPN-Gateway
object-group, net-LAN
access extensive list ip 192.168.215.0 sptnl allow 255.255.255.0 192.168.2.0 255.255.255.0
192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
tunnel of splitting allowed access list standard 192.168.215.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
MTU 1500 Internet
IP local pool VPN_Users 192.168.2.1 - 192.168.2.250 mask 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
enable ASDM history
ARP timeout 14400
NAT-control
Global 1 interface (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0
Route outside 0.0.0.0 0.0.0.0 59.90.214.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
AAA authentication http LOCAL console
AAA authentication enable LOCAL console
LOCAL AAA authentication serial console
Enable http server
x.x.x.x 255.255.255.252 out http
http 192.168.215.0 255.255.255.252 inside
http 192.168.215.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto-map dynamic dynmap 65500 transform-set RIGHT
card crypto 10 VPN ipsec-isakmp dynamic dynmap
card crypto VPN outside interface
card crypto 10 ASA-01 set peer 221.135.138.130
card crypto 10 ASA - 01 the transform-set RIGHT value
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 65535
preshared authentication
the Encryption
sha hash
Group 2
lifetime 28800
Telnet 192.168.215.0 255.255.255.0 inside
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 5
Console timeout 0
management-access inside
VPDN group dataone request dialout pppoe
VPDN group dataone localname bb4027654187_scdrid
VPDN group dataone ppp authentication chap
VPDN username bb4027654187_scdrid password * local store
interface for identifying DHCP-client Internet customer
dhcpd dns 218.248.255.141 218.248.245.1
!
dhcpd address 192.168.215.11 - 192.168.215.254 inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
Des-sha1 encryption SSL
WebVPN
allow outside
tunnel-group-list activate
internal kun group policy
kun group policy attributes
VPN - connections 8
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value split tunnel
kunchevrolet value by default-field
test P4ttSyrm33SV8TYp encrypted password username
username kunauto password bSHrKTGl8PUbvus / encrypted privilege 15
username kunauto attributes
Strategy Group-VPN-kun
Protocol-tunnel-VPN IPSec
tunnel-group vpngroup type remote access
tunnel-group vpngroup General attributes
address pool VPN_Users
Group Policy - by default-kun
tunnel-group vpngroup webvpn-attributes
the vpngroup group alias activation
vpngroup group tunnel ipsec-attributes
pre-shared key *.
type tunnel-group test remote access
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group ipsec-attributes x.x.x.x
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:0d2497e1280e41ab3875e77c6b184cf8
: end
kunauto #.Hello
Looking at the configuration, there is an access list this nat exemption: -.
192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
But it is not applied in the States of nat.
Send the following command to the nat exemption to apply: -.
NAT (inside) 0 access-list sheep
Kind regards
Dinesh Moudgil
P.S. Please mark this message as 'Responded' If you find this information useful so that it brings goodness to other users of the community
-
"Sorry, we are unable to access your account. Your account may have been disabled. We recommend that you contact us to discuss this account. "- What should I do then?
@bell.net
Contact the @bell.net Support about the issue.
-
We have a Nextbook but are unable to access the Internet at home
We have a Nextbook but are unable to access the Internet at home, even if we have a laptop and PC. How to solve this problem? Thank you.
Hi Vernon,
1. you are trying to connect the Nextbook to wireless (Wi - fi) network in your home?
It is a tablet based on Google's Android. As it comes to one product other than Microsoft, I suggest that get you in touch with the manufacturer about this issue. You can contact them at the following link:
http://www.nextbookusa.com/techsupport.php
Hope this information is useful.
-
Have client with the latest Lenovo laptop, running Windows 7 Pro, part of a Windows 2008 domain. User never had problems earlier but takes off mobile out of office last week that he had then only on vacation. The user has Verizon Wireless for Internet access so that resign. User returned, connected area through the configuration of a connection without error, but was unable to access resources in any domain. No applications have been installed on the laptop so that it is on vacation. In windows Explorer, the user can see as other NAS PC's, printers, other devices on the network and able to access the Internet, but the doman and the server are missing from the list. The connection of the user from another PC to check the profile is ok, the user was able to resources in the domain from another PC. Had a different network user trying to connect on the laptop and had the same problem so I am confident that the problem is with the laptop itself and not domain or server. Also tried to disable the firewall on the computer laptop but did not help, empty DNS and other entries in cache but nothing helped. There were a few normal .net updates on laptop while resign but that was about it. Laptop is running Microsoft's Security Essentials for virus protection.
Any ideas on how to resolve the additional or possible causes?
Hi Jack,
The problem you are having is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public.Please post your question in the Technet Forum.You can follow this link to ask your question:Forum TechNet Windows 7:For any other corresponding Windows help, do not hesitate to contact us and we will be happy to help you. -
Cisco VPN Client cannot ping from LAN internal IP
Hello
I apologize in advance for my lack of knowledge about it, but I got a version of the software running ASA 5510 7.2 (2) and has been invited to set up a site with a client, I managed to get this configured and everything works fine. In addition, I created a group of tunnel ipsec-ra for users to connect to a particular server 192.168.10.100/24 remote, even if the connection is made successfully, I can not ping any IP on the LAN 192.168.10.0/24 located behind the ASA and when I ping inside the interface on the ASA it returns the public IP address of the external interface.
If someone out there could give me a little push in the right direction, it would be much appreciated! This is the current configuration of the device.
Thanks in advance.
: Saved
:
ASA Version 7.2 (2)
!
hostname ciscoasa5510
domain.local domain name
activate the password. 123456789 / encrypted
names of
!
interface Ethernet0/0
nameif outside
security-level 0
PPPoE client vpdn group ISP
12.34.56.789 255.255.255.255 IP address pppoe setroute
!
interface Ethernet0/1
nameif inside
security-level 100
IP 192.168.10.1 255.255.255.0
!
interface Ethernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
nameif management
security-level 100
IP 192.168.1.1 255.255.255.0
management only
!
passwd encrypted 123456789
passive FTP mode
clock timezone GMT/UTC 0
summer time clock GMT/BDT recurring last Sun Mar 01:00 last Sun Oct 02:00
DNS server-group DefaultDNS
domain.local domain name
permit outside_20_cryptomap to access extended list ip 192.168.10.0 255.255.255.0 host 10.16.2.124
permit inside_nat0_outbound to access extended list ip 192.168.10.0 255.255.255.0 host 10.16.2.124
access-list Split_Tunnel_List note the network of the company behind the ASA
Split_Tunnel_List list standard access allowed 192.168.10.0 255.255.255.0
pager lines 24
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
management of MTU 1500
IP local pool domain_vpn_pool 192.168.11.1 - 192.168.11.254 mask 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 522.bin
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
Route outside 0.0.0.0 0.0.0.0 12.34.56.789 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout, uauth 0:05:00 absolute
internal domain_vpn group policy
attributes of the strategy of group domain_vpn
value of 212.23.3.100 DNS server 212.23.6.100
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list Split_Tunnel_List
username domain_ra_vpn password 123456789 encrypted
username domain_ra_vpn attributes
VPN-group-policy domain_vpn
encrypted utilisateur.123456789 password username
encrypted utilisateur.123456789 password username
privilege of username user password encrypted passe.123456789 15
encrypted utilisateur.123456789 password username
the ssh LOCAL console AAA authentication
AAA authentication enable LOCAL console
Enable http server
http 192.168.1.0 255.255.255.0 management
http 192.168.10.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto-map dynamic outside_dyn_map 20 set pfs
Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA
card crypto outside_map 20 match address outside_20_cryptomap
peer set card crypto outside_map 20 987.65.43.21
outside_map crypto 20 card value transform-set ESP-3DES-SHA
3600 seconds, duration of life card crypto outside_map 20 set - the security association
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
aes-256 encryption
sha hash
Group 5
life 86400
crypto ISAKMP policy 30
preshared authentication
3des encryption
sha hash
Group 2
life 86400
tunnel-group 987.65.43.21 type ipsec-l2l
IPSec-attributes tunnel-group 987.65.43.21
pre-shared-key *.
tunnel-group domain_vpn type ipsec-ra
tunnel-group domain_vpn General-attributes
address domain_vpn_pool pool
Group Policy - by default-domain_vpn
domain_vpn group of tunnel ipsec-attributes
pre-shared-key *.
Telnet 192.168.10.0 255.255.255.0 inside
Telnet timeout 5
Console timeout 0
VPDN group ISP request dialout pppoe
VPDN group ISP localname [email protected] / * /
VPDN group ISP ppp authentication chap
VPDN username [email protected] / * / password *.
dhcpd dns 212.23.3.100 212.23.6.100
dhcpd lease 691200
dhcpd ping_timeout 500
domain.local domain dhcpd
!
dhcpd address 192.168.10.10 - 192.168.10.200 inside
dhcpd allow inside
!
management of 192.168.1.2 - dhcpd address 192.168.1.254
enable dhcpd management
!
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:1234567890987654321
: end
Hello
Seems to me that you are atleast lack the NAT0 configuration for your VPN Client connection.
This configuration is intended to allow the VPN Client to communicate with the local network with their original IP addresses. Although the main reason that this is necessary is to avoid this traffic to the normal rule of dynamic PAT passing this traffic and that traffic is falling for the corresponding time.
You can add an ACL rule to the existing ACL NAT0, you have above and the NAT configuration should go next
Add this
permit inside_nat0_outbound to access extended list ip 192.168.10.0 255.255.255.0 192.168.11.0 255.255.255.0
Hope this helps
Let me know how it goes
-Jouni
-
Cisco ASA 8.4 (3) remote access VPN - client connects but cannot access inside the network
I have problems to access the resources within the network when connecting with the Cisco VPN client for a version of 8.4 (3) operation of the IOS Cisco ASA 5510. I tried all new NAT 8.4 orders but cannot access the network interior. I can see traffic in newspapers when ping. I can only assume I have NAT evil or it's because the inside interface of the ASA is on the 24th of the same subnet as the network interior? Please see config below, any suggestion would be appreciated. I configured a VPN site to another in this same 5510 and it works well
Thank you
interface Ethernet0/0
Speed 100
full duplex
nameif outside
security-level 0
IP x.x.x.x 255.255.255.240
!
interface Ethernet0/1
Speed 100
full duplex
nameif inside
security-level 100
IP 10.88.10.254 255.255.255.0
!
interface Management0/0
Shutdown
nameif management
security-level 0
no ip address
!
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network of the PAT_to_Outside_ClassA object
10.88.0.0 subnet 255.255.0.0
network of the PAT_to_Outside_ClassB object
subnet 172.16.0.0 255.240.0.0
network of the PAT_to_Outside_ClassC object
Subnet 192.168.0.0 255.255.240.0
network of the LocalNetwork object
10.88.0.0 subnet 255.255.0.0
network of the RemoteNetwork1 object
Subnet 192.168.0.0 255.255.0.0
network of the RemoteNetwork2 object
172.16.10.0 subnet 255.255.255.0
network of the RemoteNetwork3 object
10.86.0.0 subnet 255.255.0.0
network of the RemoteNetwork4 object
10.250.1.0 subnet 255.255.255.0
network of the NatExempt object
10.88.10.0 subnet 255.255.255.0
the Site_to_SiteVPN1 object-group network
object-network 192.168.4.0 255.255.254.0
object-network 172.16.10.0 255.255.255.0
object-network 10.0.0.0 255.0.0.0
outside_access_in deny ip extended access list a whole
inside_access_in of access allowed any ip an extended list
11 extended access-list allow ip 10.250.1.0 255.255.255.0 any
outside_1_cryptomap to access extended list ip 10.88.0.0 255.255.0.0 allow object-group Site_to_SiteVPN1
mask 10.250.1.1 - 10.250.1.254 255.255.255.0 IP local pool Admin_Pool
NAT static NatExempt NatExempt of the source (indoor, outdoor)
NAT (inside, outside) static source any any static destination RemoteNetwork4 RemoteNetwork4-route search
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork1 RemoteNetwork1
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork2 RemoteNetwork2
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork3 RemoteNetwork3
NAT (inside, outside) static source LocalNetwork LocalNetwork static destination RemoteNetwork4 RemoteNetwork4-route search
!
network of the PAT_to_Outside_ClassA object
NAT dynamic interface (indoor, outdoor)
network of the PAT_to_Outside_ClassB object
NAT dynamic interface (indoor, outdoor)
network of the PAT_to_Outside_ClassC object
NAT dynamic interface (indoor, outdoor)
Access-group outside_access_in in interface outside
inside_access_in access to the interface inside group
Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
dynamic-access-policy-registration DfltAccessPolicy
Sysopt connection timewait
Service resetoutside
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-ikev1 esp-md5-hmac bh-series
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto-map dynamic dynmap 10 set pfs
Crypto-map dynamic dynmap 10 set transform-set bh - set ikev1
life together - the association of security crypto dynamic-map dynmap 10 28800 seconds
Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000
Crypto-map dynamic dynmap 10 the value reverse-road
card crypto mymap 1 match address outside_1_cryptomap
card crypto mymap 1 set counterpart x.x.x.x
card crypto mymap 1 set transform-set ESP-AES-256-SHA ikev1
card crypto mymap 86400 seconds, 1 lifetime of security association set
map mymap 1 set security-association life crypto kilobytes 4608000
map mymap 100-isakmp ipsec crypto dynamic dynmap
mymap outside crypto map interface
crypto isakmp identity address
Crypto isakmp nat-traversal 30
Crypto ikev1 allow outside
IKEv1 crypto ipsec-over-tcp port 10000
IKEv1 crypto policy 5
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 1
life 86400
IKEv1 crypto policy 50
preshared authentication
the Encryption
md5 hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
preshared authentication
aes-256 encryption
sha hash
Group 1
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
Telnet timeout 5
Console timeout 0
management-access inside
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal BACKDOORVPN group policy
BACKDOORVPN group policy attributes
value of VPN-filter 11
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelall
BH.UK value by default-field
type tunnel-group BACKDOORVPN remote access
attributes global-tunnel-group BACKDOORVPN
address pool Admin_Pool
Group Policy - by default-BACKDOORVPN
IPSec-attributes tunnel-group BACKDOORVPN
IKEv1 pre-shared-key *.
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group ipsec-attributes x.x.x.x
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
Excellent.
Evaluate the useful ticket.
Thank you
Rizwan James
-
Cannot access internal resources
I was able to get the internal resources with the same VPN pool (192.168.100.0) internal IP address. Now, I want to have a different internal IP address VPN pool. For example, I want to have the pool 192.168.101.1 VPN - 192.168.101.250. I was able to connect to the VPN client, but I can't ping or access the internet resource (192.168.100.13). Can you help me? The configuration file is attached.
Thank you.
Laura
Laura,
Seems you have to add the new pool 192.168.101.1 VPN - 192.168.101.250 to your LIST of Inside_nat0_outbound:
Should look to this now the two internal and VPN pool included address ranges:
Inside_nat0_outbound list of allowed ip extended access any 192.168.100.0 255.255.255.0
Inside_nat0_outbound list of allowed ip extended access all 192.168.101.0 255.255.255.0
Hope this helps,
Mike
-
VPN connects but can't access internal devices
Thanks in advance for any help that can be provided.
I use AnyConnect to create a VPN with an ASA 5505. Once connected, the client needs to access a device behind a router in 1941.
Internally, (without using VPN), all my itinerary runs correctly. My VPN client can connect and when I put a route on my router from 1941, I am able to ping this particular device. But my VPN client cannot appear ping all the remaining devices on the same internal range as the ASA 5505 or whatever happened on 1941.
Device far router VPN Client ASA 5505 1941 Workstation
192.168.201.20---> outside IP x.x.x.x / / internal 192.168.101.1 192.168.101.56 192.168.101.2 / / 192.168.8.1 192.168.8.150
Client connects and get the IP address of the ASA
Cannot ping it cannot ping
Can ping the internal IP address of 1941
* (after creating a static route)
I was playing with my setup intensively to try to make this work. Split tunneling is enabled and is required.
Here is my current config:
hostnameMYHOST
activate mUUvr2NINofYuSh2 encrypted password
UNDrnIuGV0tAPtz2 encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
switchport access vlan 7
!
interface Vlan1
nameif inside
security-level 100
192.168.101.1 IP address 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP x.x.x.x 255.255.0.0
!
interface Vlan7
prior to interface Vlan1
nameif DMZ
security-level 20
IP 137.57.183.1 255.255.255.0
!
passive FTP mode
clock timezone STD - 7
DNS domain-lookup outside
the obj_any_dmz object-group network
192.168.101.0 IP Access-list extended sheep 255.255.255.0 allow all
192.168.201.0 IP Access-list extended sheep 255.255.255.0 allow all
tunneling split list of permitted access standard 192.168.101.0 255.255.255.0
pager lines 24
Enable logging
debug logging in buffered memory
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
MTU 1500 DMZ
mask 192.168.101.125 - 192.168.101.130 255.255.255.0 IP local pool Internal_Range
IP local pool vpn_pool 192.168.201.20 - 192.168.201.30 mask 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global interface 10 (external)
NAT (inside) 0 access-list sheep
NAT (inside) 1 0.0.0.0 0.0.0.0
NAT (DMZ) 10 137.57.183.0 255.255.255.0
Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
Route inside 192.168.8.0 255.255.255.0 192.168.101.2 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
http server enable 64000
http 0.0.0.0 0.0.0.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto ca trustpoint ASDM_TrustPoint1
registration auto
name of the object CN = MYHOST
ClientX_cert key pair
Configure CRL
string encryption ca ASDM_TrustPoint1 certificates
certificate 0f817951
308201e7 a0030201 30820150 0202040f 0d06092a 81795130 864886f7 0d 010105
05003038 31173015 06035504 03130e41 494d452d 56504e2d 42415455 53311d 30
1b06092a 864886f7 0d 010902 160e4149 4d452d56 504e2d42 41545553 301e170d
31333036 32373137 32393335 5a170d32 33303632 35313732 3933355a 30383117
30150603 55040313 0e41494d 452-5650 4e2d4241 54555331 1d301b06 092 d has 8648
86f70d01 0902160e 41494d 45 2d56504e 424154 55533081 9f300d06 092 2d has 8648
86f70d01 01010500 03818d 30818902 00 818100c 9 ff840bf4 cfb8d394 2 c 940430
1887f25a 49038aa0 1299cf10 bda2a436 227dcdbf f1c5566b c35c2f19 8b3514d3
4e24f5b1 c8840e8c 60e2b39d bdc0082f 08cce525 97ffefba d42bb087 81b9adb9
db0a8b2f b643e651 d17cd6f8 f67297f2 d785ef46 c3acbb39 615e1ef1 23db072c
783fe112 acd6dc80 dc38e94b 6e56fe94 d59d5d02 03010001 300 d 0609 2a 864886
8181007e f70d0101 05050003 29e90ea0 e337976e 9006bc02 402fd58a a1d30fe8
b2c1ab49 a1828ee0 488d1d2f 1dc5d150 3ed85f09 54f099b2 064cd 622 dc3d3821
fca46c69 62231fd2 6e396cd1 7ef586f9 f41205af c2199174 3c5ee887 42b684c9
7f4d2045 4742adb5 d70c3805 4ad13191 8d802bbc b2bcd8c7 8eec111b 761d89f3
63ebd49d 30dd06f4 e0fa25
quit smoking
crypto ISAKMP allow outside
crypto ISAKMP policy 40
preshared authentication
aes-256 encryption
sha hash
Group 5
life 86400
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 inside
SSH 0.0.0.0 0.0.0.0 DMZ
SSH timeout 10
Console timeout 0
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
SSL encryption rc4 - md5, rc4-aes128-sha1 aes256-3des-sha1 sha1 sha1
SSL-trust outside ASDM_TrustPoint1 point
WebVPN
allow outside
SVC disk0:/anyconnect-win-2.4.1012-k9.pkg 1 image
enable SVC
internal ClientX_access group strategy
attributes of Group Policy ClientX_access
4.2.2.2 DNS server value
VPN-tunnel-Protocol svc
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value split tunneling
access.local value by default-field
the address value vpn_pool pools
IPv6 address pools no
WebVPN
SVC mtu 1406
generate a new key SVC time no
SVC generate a new method ssl key
username privilege 15 encrypted password ykAxQ227nzontdIh ClientX
ClientX username attributes
VPN-group-policy ClientX_access
type of service admin
tunnel-group ClientX type remote access
attributes global-tunnel-group ClientX
address pool Internal_Range
Group Policy - by default-ClientX_access
type tunnel-group SSLClientProfile remote access
attributes global-tunnel-group SSLClientProfile
Group Policy - by default-ClientX_access
type tunnel-group ClientX_access remote access
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:da38065247f7334a5408b7ada3af29ae
: end
OK, lets go on... ;-)
Split tunneling: the ACL must include all the networks you want to join via the VPN:
tunneling split list of permitted access standard 192.168.101.0 255.255.255.0
tunneling split list of permitted access standard 192.168.8.0 255.255.255.0
NAT: Do not use 'everything' in the nat exemption, but specify all the traffic that should not be natted:
IP 192.168.101.0 allow Access-list extended sheep 255.255.255.0 192.168.201.0 255.255.255.0
IP 192.168.8.0 allow Access-list extended sheep 255.255.255.0 192.168.201.0 255.255.255.0
Routing: The 1941 needs a route for the vpn-pool pointing on the SAA (just in case there is no default route to the ASA)
--
Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
http://www.Kiva.org/invitedBy/karsteni -
Site to site VPN with the VPN Client for both sites access?
Current situation:
Scenario is remote to the main office. Site IPSEC tunnel site (netscreen) remote in hand (506th pix). Cisco VPN Client of main office of remote access to users.
It's that everything works perfectly.
Problem:
Now we want remote users who connect to the seat to also be able to access resources in the remote offices.
This seems like it would be easy to implement, but I can't understand it.
Thanks in advance.
Rollo
----------
#10.10.10.0 = Network1
#10.10.11.0 = Network2
#172.16.1.0 = vpn pool
6.3 (4) version PIX
access-list 101 permit ip 10.10.10.0 255.255.255.0 172.16.1.0 255.255.255.0
access-list 101 permit ip 10.10.10.0 255.255.255.0 10.10.11.0 255.255.255.0
splitTunnel 10.10.10.0 ip access list allow 255.255.255.0 any
splitTunnel ip 10.10.11.0 access list allow 255.255.255.0 any
access-list 115 permit ip any 172.16.1.0 255.255.255.0
access-list 116 allow ip 10.10.10.0 255.255.255.0 10.10.11.0 255.255.255.0
IP access-list 116 allow all 10.10.11.0 255.255.255.0
access-list 116 allow ip 10.10.11.0 255.255.255.0 10.10.10.0 255.255.255.0
ICMP allow all outside
ICMP allow any inside
Outside 1500 MTU
Within 1500 MTU
IP address outside 209.x.x.x 255.255.255.224
IP address inside 10.10.10.1 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
IP local pool 172.16.1.0 vpnpool - 172.16.1.50
Global 1 interface (outside)
Global (outside) 10 209.x.x.x 255.255.255.224
(Inside) NAT 0-list of access 101
NAT (inside) 10 10.10.10.0 255.255.255.0 0 0
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 209.x.x.x 1
Timeout xlate 01:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
enable floodguard
Permitted connection ipsec sysopt
Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
crypto dynamic-map Clients_VPN-dynmap 10 transform-set RIGHT
35 Myset1 ipsec-isakmp crypto map
correspondence address 35 Myset1 map cryptographic 116
card crypto Myset1 35 counterpart set x.x.x.x
card crypto Myset1 35 set transform-set Myset1
Myset1 card crypto ipsec 90-isakmp dynamic dynmap Clients_VPN
client configuration address card crypto Myset1 launch
client configuration address card crypto Myset1 answer
interface Myset1 card crypto outside
ISAKMP allows outside
ISAKMP key * address x.x.x.x 255.255.255.255 netmask No.-xauth-no-config-mode
ISAKMP identity address
ISAKMP nat-traversal 20
part of pre authentication ISAKMP policy 15
ISAKMP policy 15 3des encryption
ISAKMP policy 15 sha hash
15 1 ISAKMP policy group
ISAKMP duration strategy of life 15 28800
part of pre authentication ISAKMP policy 20
ISAKMP policy 20 3des encryption
ISAKMP policy 20 chopping sha
20 2 ISAKMP policy group
ISAKMP duration strategy of life 20 3600
part of pre authentication ISAKMP policy 25
encryption of ISAKMP policy 25
ISAKMP policy 25 md5 hash
25 2 ISAKMP policy group
ISAKMP living 25 3600 duration strategy
part of pre authentication ISAKMP policy 30
ISAKMP policy 30 aes-256 encryption
ISAKMP policy 30 sha hash
30 2 ISAKMP policy group
ISAKMP duration strategy of life 30 86400
vpngroup address vpnpool pool mygroup
vpngroup dns-server dns1 dns2 mygroup
vpngroup mygroup wins1 wins2 wins server
vpngroup mygroup by default-domain mydomain
vpngroup split splitTunnel tunnel mygroup
vpngroup idle time 64000 mygroup
mygroup vpngroup password *.
Telnet timeout 5
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd outside auto_config
Hi Rollo,
You can not be implemented for a simple reason, it is not supported on the version 6.x PIX. It relies on the PIX 7.x worm but 7.x is not supported on PIX 506. Thus, in a Word, it can be reached on a PIX 506. If you have an ASA, a PIX 515 running 7.x, a router or a hub as well, it can be reached.
HTH,
Please rate if this helps,
Kind regards
Kamal
-
Help cannot access internal resources
Hello I am trying to configure an ASA 5505 at home and connecting through the Cisco Secure mobility Client
Internal network: 10.37.1.0/24
Guest network: 10.37.2.0/24
DHCP VPN: 10.37.3.0/24
I am only able to connect with the local account of ASA, not LDAP as I want. After I connect I get my 10.37.1.0/24 (my internal network) secure route but I can't ping, RDP, SSH, etc. anything inside. I get the message below...
4 October 30, 2013 12:08:36 10.37.3.130 Refuse icmp outside CBC: 10.37.3.130 dst host: SPIDERMAN (type 8, code 0) by access-group "outside_access_in" [0x0, 0x0] Any help would be greatly appreciated! Thank you.
Registered
: Written by enable_15 to the 09:09:04.925 EDT Wednesday, October 30, 2013
!
ASA Version 8.2 (5)
!
hostname aquaman
domain batcave.local
activate the encrypted password of O8X.8O1jZvTr6Rh3
zHg4tACBjpuqj6q5 encrypted passwd
names of
name 10.37.1.99 GREEN-ARROW
name OpenDNS1 description resolver1.opendns.com 208.67.222.222
name OpenDNS2 description resolver2.opendns.com 208.67.220.220
name 208.67.222.220 OpenDNS3 resolver3.opendns.com description
name 208.67.220.222 OpenDNS4 resolver4.opendns.com description
name 10.37.1.15 DU-HULK
name 178.33.199.65 ComodoMX1 mxsrv1.spamgateway.comodo.com description
name 178.33.199.66 ComodoMX2 mxsrv2.spamgateway.comodo.com description
name 10.37.1.101 SPIDERMAN
name 10.37.1.10 DAREDEVIL
name 65.73.180.177 WorkIP
name 10.37.1.254 OpenVPNAS
name 10.37.3.0 VPN_DHCP
name 10.37.2.10 GuestWirelessAP
name 10.37.1.20 DU-FLASH
name 10.37.1.200 BR_1
name 10.37.1.201 BR_2
name 10.37.1.30 IRONMAN
name 10.37.1.25 WIKI
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
switchport access vlan 5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif House
security-level 100
IP 10.37.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address dhcp setroute
!
interface Vlan5
nameif comments
security-level 50
IP 10.37.2.254 255.255.255.0
!
!
interval M-F_9-16
periodical Monday to Friday 09:00 to 16:00
!
Banner motd
boot system Disk0: / asa825 - k8.bin
passive FTP mode
clock timezone IS - 5
clock to summer time EDT recurring
DNS domain-lookup outside
DNS server-group DefaultDNS
Server name OpenDNS1
Server name OpenDNS2
Server name OpenDNS3
Server name OpenDNS4
domain batcave.local
permit same-security-traffic inter-interface
object-group service RDP - tcp
Remote Desktop Protocol Description
EQ port 3389 object
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
the ComodoSpamFilter object-group network
host of the object-Network ComodoMX1
host of the object-Network ComodoMX2
the OpenDNSServers object-group network
host of the object-Network OpenDNS2
host of the object-Network OpenDNS4
host of the object-Network OpenDNS3
host of the object-Network OpenDNS1
VNC tcp service object-group
EQ port 5900 object
smartmail tcp service object-group
object-port 9998 eq
http2 tcp service object-group
EQ object of port 8080
RDP2 tcp service object-group
port-object eq 3789
DM_INLINE_TCP_1 tcp service object-group
EQ port ssh object
port-object eq telnet
object-group network Netflix
host of the object-Network BR_1
the object-BR_2 Network host
object-group service tcp MOP3
port-object eq 3999
outside_access_in list extended access permit tcp any interface outside of the object-group RDP log disable
outside_access_in list extended access permit tcp any interface outside eq ftp log disable
outside_access_in list extended access permit tcp any interface outside eq www disable journal
outside_access_in list extended access permitted tcp object-group ComodoSpamFilter interface outside eq smtp log disable
outside_access_in list extended access permit tcp any interface outside of the object-group smartmail disable journal
access-list extended outside_access_in permit tcp host WorkIP log disable interface outside object-group VNC
outside_access_in list extended access permit tcp any interface outside of the object-group http2 disable journal
outside_access_in list extended access permit tcp any interface outside of the object-group RDP2 journal disable
outside_access_in list extended access permit icmp any interface outside disable newspaper echo-reply
home_access_in list extended access allowed object-group TCPUDP 10.37.1.0 255.255.255.0 OpenDNSServers eq field journal disable object-group
home_access_in list extended access allowed host TCPUDP object-group SPIDERMAN turn off no matter what field eq journal
home_access_in list extended access denied object-group TCPUDP 10.37.1.0 255.255.255.0 disable any log domain eq
home_access_in allowed extended access list ip all all disable Journal
guest_access_in list extended access allowed object-group TCPUDP 10.37.2.0 255.255.255.0 OpenDNSServers eq field journal disable object-group
guest_access_in list extended access deny tcp 10.37.2.0 255.255.255.0 disable any newspaper ftp EQ
guest_access_in list extended access deny tcp 10.37.2.0 255.255.255.0 disable any newspaper of DM_INLINE_TCP_1-group of objects
guest_access_in list extended access deny tcp 10.37.2.0 255.255.255.0 disable any newspaper RDP-group of objects
guest_access_in list extended access deny tcp 10.37.2.0 255.255.255.0 disable any newspaper VNC object-group
guest_access_in list extended access denied object-group TCPUDP 10.37.2.0 255.255.255.0 disable any log domain eq
guest_access_in to access extended list ip any any newspaper disable time-range allow M-F_9-16
Standard access list Split_Tunnel_List allow 10.37.1.0 255.255.255.0
pager lines 24
Enable logging
timestamp of the record
logging trap notifications
asdm of logging of information
logging - the id of the device hostname
logging host home-FLASH
Home of MTU 1500
Outside 1500 MTU
Comments of MTU 1500
local pool VPN_DHCP 10.37.3.130 - 10.37.3.139 255.255.255.0 IP mask
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any home
ICMP permitted outside the host WorkIP
ICMP deny everything outside
ICMP deny any guest
ASDM image disk0: / asdm - 714.bin
Location THE-HULK 255.255.255.255 ASDM home
Location WIKI 255.255.255.255 ASDM home
Location GREEN-ARROW 255.255.255.255 ASDM home
Location OpenDNS2 255.255.255.255 ASDM home
Location OpenDNS4 255.255.255.255 ASDM home
Location OpenDNS3 255.255.255.255 ASDM home
Location OpenDNS1 255.255.255.255 ASDM home
Location ComodoMX1 255.255.255.255 ASDM home
Location ComodoMX2 255.255.255.255 ASDM home
Location SPIDERMAN 255.255.255.255 ASDM home
Location DAREDEVIL 255.255.255.255 ASDM home
Location WorkIP 255.255.255.255 ASDM home
Location OpenVPNAS 255.255.255.255 ASDM home
Location VPN_DHCP 255.255.255.0 ASDM home
Location GuestWirelessAP 255.255.255.255 ASDM home
Location LA-FLASH 255.255.255.255 ASDM home
Location IRONMAN 255.255.255.255 ASDM home
don't allow no asdm history
ARP timeout 14400
NAT-control
Overall 101 (external) interface
NAT (House) 101 0.0.0.0 0.0.0.0
NAT (guest) 101 0.0.0.0 0.0.0.0
3389 GREEN ARROW 3389 netmask 255.255.255.255 interface static tcp (home, outdoor)
public static tcp (home, outside) THE-HULK netmask 255.255.255.255 ftp ftp interface
public static tcp (home, outside) interface www THE-HULK www netmask 255.255.255.255
public static tcp (home, outside) interface smtp smtp netmask 255.255.255.255 IRONMAN
9998 IRONMAN 9998 netmask 255.255.255.255 interface static tcp (home, outdoor)
5900 5900 SPIDERMAN netmask 255.255.255.255 interface static tcp (home, outdoor)
public static (home, outside) udp interface tftp THE tftp netmask 255.255.255.255 FLASH
3789 THE FLASH 3789 netmask 255.255.255.255 interface static tcp (home, outdoor)
8080 8080 WIKI netmask 255.255.255.255 interface static tcp (home, outdoor)
Access-group home_access_in in interface House
Access-group outside_access_in in interface outside
Access-group guest_access_in in the comments of the interface
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
AAA-server protocol ldap BATCAVE
AAA-server BATCAVE (home) host DAREDEVIL
LDAP-base-dn = Users, OR =, DC = batcave, DC = local
LDAP-group-base-dn memberOf = CN = Cisco VPN Users, OR = Groups, OU = staff, DC = batcave, DC = local
LDAP-naming-attribute sAMAccountName
LDAP-login-password npYDApHrdVjOTcj8kJha
LDAP-connection-dn CN = Cisco account LDAP, OU = Service accounts, DC = batcave, DC = local
microsoft server type
the ssh LOCAL console AAA authentication
LOCAL AAA authentication serial console
LOCAL AAA authorization exec
http server enable 3737
http WorkIP 255.255.255.255 outside
http 10.37.1.0 255.255.255.0 House
redirect http outside 80
http redirection 80 home
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
No vpn sysopt connection permit
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
No vpn-addr-assign aaa
VPN-addr-assign local reuse / time 5
Telnet timeout 5
SSH GREEN-ARROW 255.255.255.255 House
SSH SPIDERMAN 255.255.255.255 House
SSH daredevil 255.255.255.255 House
SSH WorkIP 255.255.255.255 outside
SSH timeout 10
SSH version 2
Console timeout 30
dhcpd outside auto_config
!
dhcprelay Server DAREDEVIL home
dhcprelay enable comments
dhcprelay setroute comments
time-out of 60 dhcprelay
Host priority queue
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
NTP Server 64.90.182.55 prefer external source
Server TFTP FLASH-home of THEftp://10.37.1.20/ t
WebVPN
Enable home
allow outside
SVC disk0:/anyconnect-win-3.1.04066-k9_3.pkg 1 image
enable SVC
attributes of Group Policy DfltGrpPolicy
value of server DNS 10.37.1.10
VPN - connections 1
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list Split_Tunnel_List
Batcave.local value by default-field
WebVPN
SVC request to enable default webvpn
aquaman encrypted KKOPGG99Bk0xyhXS privilege 15 password username
jared YlQ4V6UbWiR/Dfov password user name encrypted privilege 15
attributes global-tunnel-group DefaultWEBVPNGroup
address VPN_DHCP pool
type tunnel-group HomeVPN remote access
attributes global-tunnel-group HomeVPN
address VPN_DHCP pool
authentication-server-group BATCAVE
!
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
!
10.37.1.30 SMTP server
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:65c8e856cde7d73200dd38f670613c2b
: end
Hi Jared,
Because your configuration has the statement without sysopt connection VPN-enabled -'re missing you an exempt nat rule. This is why you must configure an access list to allow traffic between your network VPN of RA and your inside the subnet - apply rule to your house where the 10.37.1.0/24 of the interface.
Example:
access extensive list ip 10.37.1.0 nonat_rule allow 255.255.255.0 10.37.3.0 255.255.255.0
NAT (House) access 0-list nonat_ruleGive that a try
Concerning
-
Since the update last night (05/02/2013) we are unable to access the internet.
My son says that there is an update last night when he was on the computer and the browser only, that we can use to access the internet now is Windows Internet Explorer. I tried all of the recommended patches and it still does not work.
Some Firefox problems can be solved by performing a clean reinstall. This means that you remove Firefox and all the leftover program files and then reinstall Firefox. Please follow these steps one by one:
- Download the latest version of Firefox from http://www.mozilla.org office and save the installer to your computer.
- Once the download is complete, close all Firefox Windows (click Exit in the file menu or Firefox) and confirm all future messages.
- Now, uninstall Firefox by following the steps mentioned in the article to Uninstall Firefox .
IMPORTANT: Under Windows, the uninstall program has the option to remove your personal data and settings. Make sure that you have not check this option. If not all of your bookmarks, passwords, extensions, customizations and other Firefox data user profile will be removed from your computer.
After uninstalling Firefox on Windows, delete the folder of the program "Mozilla Firefox", located by default in one of the following locations:
- (Windows 32-bit) C:\Program Files\Mozilla Firefox
- (On 64-bit Windows) C:\Program Files (x 86) \Mozilla Firefox
- Go to the Windows Start menu and click on 'computer '.
- In the Explorer window that opens, double-click on disk Local (c) to open the C:\ drive.
- Find the folder "Program Files (x 86)" or "Program Files".
- On 32-bit Windows, double-click the Program Files folder to open it.
- On 64-bit Windows, you'll see a folder "Program Files (x 86)" AND a "Program Files" folder. Open the Program Files (x 86) folder.
- You are looking for a folder of Mozilla Firefox . If you find one, right click and select delete and confirm that you want to move the folder to the trash.
Now, go ahead and reinstall Firefox:
- Double-click on the downloaded Setup file and go through the steps in the installation wizard.
- Once the wizard is completed, click to open Firefox directly after clicking the Finish button.
Please report back to see if this helped you!
-
Clients are unable to reach server
I worked with Workstation just a short time.
I have a box of 'server' pro Win7 with workstation, with a guest OS of FreeNAS configured to share data via CIFS. My goal is to explore the options NAS and learning Workstation.
The server host operating system can see the CIFS sharing perfectly.
The problem is that the other boxes pro Win7 client on the network do not see the sharing and actually cannot ping the IP Address of the server. The server host operating system can see the actions and can ping to the host.
Host the server gets the IP Address of the dhcp server and the network of comments is affected by DHCP, networking with guest card status, an address ip like 192.168.131.5 or something like that. I'm from the network. Customer boxes all have intellectual property like 192.168.1.x. Not sure if this is important.
There is Kaspersky firewall on the host of the server and each client is protected by the Zone Alarm Firewall. I disabled all firewall no disernable effect. I tried the network wired and wireless options, but they both react the same.
To identify the problem, I tried these options:
1. install FreeNAS unvirtualized and all Win7 customers could see action. IP is DHCP in the range 192.168.1.x
2. installed Virtualbox on Win7 host with FreeNAS invited and all Win7 customers could see action. Guest network is bridged, DHCP, host taking NIC status.
I'm just starting this, but it seems to me that the solution is a badly configured workstation setting.
Any help much appreciated.
Steve.
Welcome to the community,
the approach is correct, but it seems that you have not configured in network bridge in the virtual machine settings correctly. Otherwise, you should get a valid IP address of your DHCP in the range of 192.168.1.x and not 192.168.131.5.
Open the 'virtual network' Editor to know what vmnet belongs to 192.168.131.x.
André
-
Win 7 VPN client cannot access remote resources beyond the VPN server
I have a Win 7 laptop with work and customer Win 7 VPN set up, and through it that I can access everything allowed resources on the remote network.
I built a new computer, set up the Win 7 client with the exact same parameters everywhere, connected to the VPN with success, but can not access any of the resources on the remote network that I can on my laptop.
Win 7 64 bit SP 1
I did research online and suggestions have already had reason of my new set up. In addition, I have a second computer that I've set up the VPN client, and I'm having the same problem. VPN connects successfully, but is unable to access the resources.
Tested with firewall off the coast.
Troubleshooting Diagnostic reports: your computer seems to be configured correctly, distance resources detected, but not answered do not.
I created another VPN client on the new computer to another remote network and everything works perfectly.
Remember the old VPN connection to the remote network that does not work on the new computer works perfectly on Win 7 64 bit laptop computer.
So, what do I find also different between identical configurations "should be" where we work and two new machines is not?
It must be something stupid.
Hello
This question is more suited for a TechNet audience. I suggest you send the query to the Microsoft TechNet forum. See the link below to do so:
https://social.technet.Microsoft.com/forums/Windows/en-us/home?Forum=w7itpronetworkingPlease let us know if you have more queries on Windows.
Maybe you are looking for
-
I don't have the option open as a verified sidebar, never have, and NEVER had it do this til today. I can't get rid of him open like a sidebar when I open ff. Help, please. There must be another way to get rid of it before you restore my pc!
-
Upgrading RAM on Satellite A40 - VH3
I want to upgrade the memory of my laptop Satellite A40 - VH3 from 512 MB to 1 or 2 GB. If someone could confirm this - it is my understanding that there are already 2 sticks of 256 MB PC2100 (266) DDR RAM in the laptop (from factory). The maximum th
-
Ordered a droid Force Z bike 7/27, estimated 8/10 - still no movement of the status
No matter who commands a Force of Z Moto DROID Motorola.com benefits updates? I have a number of order confirmation, but this status has not changed in nearly two weeks.
-
3270NR HP Envy 17 - not in the market of the UAE UNITED for the purchase of
I would buy it but this product not available in the UNITED Arab Emirates... Screen size 17.3 inches Max screen resolution 1920 x 1080 pixels processor 2.3 GHz Core i7-3610QM RAM 8 GB SDRAM Hard Drive 750 GB Graphics coprocessor AMD Radeon HD 7850 M
-
analog parallel DAQmx reads at different rates of acquisition
I'm running two 9172 chassis with a total of 11 modules. I have two 9217 modules for reading RTDs and a 9205 for sensors of reading level. I've set up three spots, one for each module.If I do a task sheet and place DAQmx Read in a loop, I can read al