VPN problem connection


These options are enabled by default on the router check the Security and administration tabs.

Tags: Linksys Routers

Similar Questions

  • Problem with "vpn sysopt connection permit.

    Hi all

    I would like to ask you for advice with "vpn sysopt connection permit". I have a problem with by-pass-access list (acl) in the INSIDE interface. As I understand it and I'm going to use this command, there is no need to especialy allow traffic in the access list for the INSIDE and I can control the filter-vpn traffic. But in my case it's quite the opposite, I want particularly to this INTERIOR acl traffi. When I allow this traffic inside acl L2L tunnel rises, hollow traffic flow vpn-fltr ane acl that everything is OK. But when I do not allow that this traffic is inside of the rule with Deny statement in acl INSIDE block traffic and tunnel goes ever upward. Part of the configuraciton which you can view below.

    Please let me know if I'm wrong, or what I did wrong?

    Thank you

    Karel

    PHA-FW01 # view worm | Worm Inc

    Cisco Adaptive Security Appliance Software Version 4,0000 1

    PHA-FW01 # display ru all sys

    No timewait sysopt connection

    Sysopt connection tcpmss 1380

    Sysopt connection tcpmss minimum 0

    Sysopt connection permit VPN

    Sysopt connection VPN-reclassify

    No sysopt preserve-vpn-stream connection

    no RADIUS secret ignore sysopt

    No inside sysopt noproxyarp

    No EXT-VLAN20 sysopt noproxyarp

    No EXT-WIFI-VLAN30 sysopt noproxyarp

    No OUTSIDE sysopt noproxyarp

    PHA-FW01 # display the id of the object-group ALGOTECH

    object-group network ALGOTECH

    object-network 10.10.22.0 255.255.255.0

    host of the object-Network 172.16.15.11

    PHA-FW01 # show running-config id of the object VLAN20

    network of the VLAN20 object

    subnet 10.1.2.0 255.255.255.0

    L2L_to_ALGOTECH list extended access permitted ip object object-group VLAN20 ALGOTECH

    extended access list ACL-ALGOTECH allow ip object-group object VLAN20 ALGOTECH

    Note EXT-VLAN20 of access list =.

    access list EXT-VLAN20 allowed extended ip object VLAN20 ALGOTECH #why object-group must be the rule here?

    access list EXT-VLAN20 extended permitted udp object VLAN20 object-group OUT-DNS-SERVERS eq field

    EXT-VLAN20 allowed extended VLAN20 object VPN-USERS ip access list

    EXT-VLAN20 extended access list permit ip object VLAN20 OPENVPN-SASPO object-group

    EXT-VLAN20 allowed extended object VLAN10 VLAN20 ip access list

    deny access list extended VLAN20 EXT ip no matter what LOCAL NETS of object-group paper

    EXT-VLAN20 allowed extended icmp access list no echo

    access list EXT-VLAN20 allowed extended object-group SERVICE VLAN20 object VLAN20 everything

    EXT-VLAN20 extended access list deny ip any any newspaper

    extended access list ACL-ALGOTECH allow ip object-group object VLAN20 ALGOTECH

    GROUP_POLICY-91 group policy. X 41. X.12 internal

    GROUP_POLICY-91 group policy. X 41. X.12 attributes

    value of VPN-filter ACL-ALGOTECH

    Ikev1 VPN-tunnel-Protocol

    tunnel-group 91.X41. X.12 type ipsec-l2l

    tunnel-group 91.X41. X.12 General attributes

    Group Policy - by default-GROUP_POLICY-91. X 41. X.12

    tunnel-group 91.X41. X.12 ipsec-attributes

    IKEv1 pre-shared-key *.

    PHA-FW01 # show running-config nat

    NAT (EXT-VLAN20, outdoors) static source VLAN20 VLAN20 static destination ALGOTECH ALGOTECH non-proxy-arp-search to itinerary

    network of the VLAN20 object

    dynamic NAT interface (EXT-VLAN20, outdoors)

    group-access to the INTERIOR in the interface inside

    Access-group interface VLAN20 EXT EXT-VLAN20

    Hello

    The command "sysopt connection permit-vpn" is the default setting and it applies only to bypass ACL interface to the interface that ends the VPN. It would be connected to the external network interface. This custom has no effect on the other interfaces ACL interface.

    So if you initiate or need to open connections from your local network to remote network through the VPN L2L connection then you will need to allow this traffic on your LAN interface ACL networks.

    If the situation was that only the remote end has launched connections to your network then 'sysopt permit vpn connection' would allow their connections around the external interfaces ACL. If If you have a VPN configured ACL filter, I think that the traffic will always accompany against this ACL.

    Here are the ASA reference section to order custom "sysopt"

    http://www.Cisco.com/en/us/docs/security/ASA/command-reference/S21.html#wp1567918

    -Jouni

  • Problems connecting to help connect any and the Ipsec VPN Client

    I have problems connecting with the VPN client connect no matter what.  I can connect with the Ipsec VPN client in Windows 7 32 bit.

    Here is my latest config running.

    Thank you for taking the time to read this.

    passwd encrypted W/KqlBn3sSTvaD0T

    no names

    name 192.168.1.117 kylewooddesk kyle description

    !

    interface Vlan1

    nameif inside

    security-level 100

    IP 192.168.1.1 255.255.255.0

    !

    interface Vlan2

    nameif outside

    security-level 0

    IP address dhcp setroute

    !

    interface Ethernet0/0

    switchport access vlan 2

    !

    interface Ethernet0/1

    !

    interface Ethernet0/2

    !

    interface Ethernet0/3

    !

    interface Ethernet0/4

    !

    interface Ethernet0/5

    !

    interface Ethernet0/6

    !

    interface Ethernet0/7

    !

    boot system Disk0: / asa822 - k8.bin

    passive FTP mode

    DNS lookup field inside

    DNS domain-lookup outside

    DNS server-group DefaultDNS

    domain wood.local

    permit same-security-traffic intra-interface

    object-group service rdp tcp

    access rdp Description

    EQ port 3389 object

    outside_access_in list extended access permit tcp any interface outside eq 3389

    outside_access_in list extended access permit tcp any interface outside eq 8080

    outside_access_in list extended access permit tcp any interface outside eq 3334

    outside_access_in to access extended list ip 192.168.5.0 allow 255.255.255.240 192.168.1.0 255.255.255.0

    woodgroup_splitTunnelAcl list standard access allowed host 192.168.1.117

    inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.240

    outside_access_in_1 list extended access permit tcp any host 192.168.1.117 eq 3389

    woodgroup_splitTunnelAcl_1 list standard access allowed 192.168.1.0 255.255.255.0

    inside_nat0_outbound_1 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.240

    inside_nat0_outbound_1 to access extended list ip 192.168.5.0 allow 255.255.255.240 all

    inside_test list extended access permit icmp any host 192.168.1.117

    no pager

    Enable logging

    timestamp of the record

    asdm of logging of information

    Debugging trace record

    Within 1500 MTU

    Outside 1500 MTU

    mask pool local Kyle 192.168.5.1 - 192.168.5.10 IP 255.255.255.0

    IP local pool vpnpool 192.168.1.220 - 192.168.1.230

    ICMP unreachable rate-limit 1 burst-size 1

    ASDM image disk0: / asdm - 631.bin

    don't allow no asdm history

    ARP timeout 14400

    Global (inside) 1 interface

    Global 1 interface (outside)

    NAT (inside) 0-list of access inside_nat0_outbound_1

    NAT (inside) 1 0.0.0.0 0.0.0.0

    public static interface 3389 (indoor, outdoor) 192.168.1.117 tcp 3389 netmask 255.255.255.255 dns

    public static tcp (indoor, outdoor) interface 8080 192.168.1.117 8080 netmask 255.255.255.255

    public static tcp (indoor, outdoor) interface 3334 192.168.1.86 3334 netmask 255.255.255.255

    static (inside, upside down) 75.65.238.40 192.168.1.117 netmask 255.255.255.255

    Access-group outside_access_in in interface outside

    Timeout xlate 03:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    dynamic-access-policy-registration DfltAccessPolicy

    WebVPN

    the files enable exploration

    activate the entry in the file

    enable http proxy

    Enable URL-entry

    SVC request no svc default

    AAA authentication http LOCAL console

    Enable http server

    http 192.168.1.0 255.255.255.0 inside

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

    Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

    Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

    life crypto ipsec security association seconds 28800

    Crypto ipsec kilobytes of life - safety 4608000 association

    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

    Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

    outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

    outside_map interface card crypto outside

    crypto isakmp identity address

    crypto ISAKMP allow outside

    crypto ISAKMP policy 10

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    Telnet 192.168.1.0 255.255.255.0 inside

    Telnet timeout 5

    SSH timeout 5

    Console timeout 0

    dhcpd dns 8.8.8.8 8.8.4.4

    dhcpd lease 3000

    !

    dhcpd address 192.168.1.100 - 192.168.1.130 inside

    dhcpd allow inside

    !

    a basic threat threat detection

    host of statistical threat detection

    Statistics-list of access threat detection

    no statistical threat detection tcp-interception

    WebVPN

    allow outside

    SVC disk0:/anyconnect-win-2.4.1012-k9.pkg 1 image

    enable SVC

    internal sslwood group policy

    attributes of the strategy of group sslwood

    VPN-tunnel-Protocol svc webvpn

    WebVPN

    list of URLS no

    internal group woodgroup strategy

    woodgroup group policy attributes

    value of server DNS 8.8.8.8 8.8.4.4

    Protocol-tunnel-VPN IPSec

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list woodgroup_splitTunnelAcl_1

    mrkylewood encrypted Q4339wmn1ourxj9X privilege 15 password username

    username mrkylewood attributes

    VPN-group-policy sslwood

    VPN - connections 3

    VPN-tunnel-Protocol svc webvpn

    value of group-lock sslwood

    WebVPN

    SVC request no webvpn default

    tunnel-group woodgroup type remote access

    tunnel-group woodgroup General attributes

    address pool Kyle

    Group Policy - by default-woodgroup

    tunnel-group woodgroup ipsec-attributes

    pre-shared key *.

    type tunnel-group sslwood remote access

    tunnel-group sslwood General-attributes

    address pool Kyle

    authentication-server-group (inside) LOCAL

    authentication-server-group (outside LOCAL)

    Group Policy - by default-sslwood

    !

    class-map inspection_default

    match default-inspection-traffic

    !

    !

    type of policy-card inspect dns preset_dns_map

    parameters

    message-length maximum 512

    Policy-map global_policy

    class inspection_default

    inspect the preset_dns_map dns

    inspect the ftp

    inspect h323 h225

    inspect the h323 ras

    inspect the netbios

    inspect the rsh

    inspect the rtsp

    inspect the skinny

    inspect esmtp

    inspect sqlnet

    inspect sunrpc

    inspect the tftp

    inspect the sip

    inspect xdmcp

    Review the ip options

    type of policy-card inspect dns MY_DNS_INSPECT_MAP

    parameters

    !

    global service-policy global_policy

    context of prompt hostname

    call-home

    Profile of CiscoTAC-1

    no active account

    http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

    email address of destination [email protected] / * /

    http https://tools.cisco.com/its/service/...es/DDCEService destination address

    destination-mode http transport

    Subscribe to alert-group diagnosis

    Subscribe to alert-group environment

    Subscribe to alert-group monthly periodic inventory

    monthly periodicals to subscribe to alert-group configuration

    daily periodic subscribe to alert-group telemetry

    Cryptochecksum:6fa8db79bcf695080cbdc1159b409360

    : end

    asawood (config) #.

    You also need to add the following:

    WebVPN

    tunnel-group-list activate

    output

    tunnel-group sslwood webvpn-attributes

    activation of the Group sslwood alias

    Let us know if it works.

  • Not ios10 blocking VPN PPTP connections through personal hotspot?

    I use an iPhone 6 + and was upgraded to ios10, two days ago.

    While I don't have a configuration of the VPN connection on the phone, I connect my computer laptop personal hotspot of the iPhone to use internet and sometimes connect to a VPN.

    Before my upgrade to ios10, my laptop could still connect to the VPN while connected to the hotspot from my iPhone.

    After that I updated to ios10, my laptop does not connect to the VPN I connect to.

    I see reports that Apple has abandoned the use of the connection for PPTP VPN connections on ios10.

    But most of the people having problems seem to be people who connect to their phones directly to the VPN in the iPhone settings.

    In my case, my phone is just acting under the guidance of the internet on my laptop but it seems that it does not obstruct my laptop to connect to a pptp even connection if that should have no impact on the phone itself.

    I went down to ios9 and my laptop can connect again to the VPN.

    But now my Apple Watch does not work with my phone because I improved the watch to os3.

    Any ideas if there is a work around for the connection for pptp connections using the hotspon on ios10?

    Apple mentions alternative - Prepare for the removal of PPTP VPN before you upgraded to iOS 10 and macOS Sierra - Apple Support

  • INTERNET EXPLORER IS SHOWING MY CONNECTION SUCH AS DIAL-UP OR VPN, I CONNECT DSL

    INTERNET EXPLORER IS SHOWING MY CONNECTION SUCH AS DIAL-UP OR VPN, I CONNECT DSL

    Hello

    ·        Are you able to connect to the internet?

    I suggest you follow the steps mentioned below to configure a connection.

    a. open Internet Explorer and then click Tools.

    b. click Internet Options, and then click the connection tab.

    c. click on Setup and follow the instructions on the screen.

    Apart from that, I suggest you to return the items mentioned below.

    How to troubleshoot possible causes of Internet connection problems in Windows XP

    http://support.Microsoft.com/kb/314095

    Thanks and regards.

    Thahaseena M
    Microsoft Answers Support Engineer.
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • VPN Client connection - Hong Kong to the United States.

    We have a PIX 515E with active VPN. In the United States, users have no problem connecting with the VPN client.

    However, we have a user in Hong Kong, who has problems. It can connect to the external interface and the connection. The user is assigned an IP address from the pool of reserve, but cannot connect to our server here in the States or internal ping even one of the ip addresses.

    Is there another config that needs to be done?

    Yes, the do config mode:

    ISAKMP nat-traversal

    Save with: write mem - and your done.

    Download now your username in Hong KONG to establish the connection of the VPN client and try and ping a server in-house on your side. And make sure that the MS XP firewall is disabled.

    Let me know how you go and if this does not solve your problem please rate another post could seek the same solution!

    Jay

  • Site to Site PIX VPN problems

    Hi, I currently have a site to site vpn upward and running and it works fine. I try to put the other two online and just cannot make them work. I used the same configuration of one operation but I cannot get the next tunnel. I saw several errors when debugging isakmp and ipsec and they are at the end of my configs. Anyone have any ideas? Thank you

    Main site - a vpn clients connecting too it and pt to pt vpn to 3 endpoints

    Cisco PIX Firewall Version 6.3 (3)

    * Main Site Config *.

    client_vpn 10.10.0.0 ip access list allow 255.255.0.0 192.168.0.0 255.255.255.0

    VPN_to_Site2 10.10.0.0 ip access list allow 255.255.0.0 192.168.0.0 255.255.255.0

    NAT (inside) 0-list of access client_vpn

    Permitted connection ipsec sysopt

    Crypto ipsec transform-set esp-3des esp-md5-hmac fws_encry_set

    outside_map 60 ipsec-isakmp crypto map

    address for correspondence card crypto outside_map 60 VPN_to_Site2

    crypto outside_map 60 peer 64.X.X.19 card game

    card crypto outside_map 60 transform-set fws_encry_set

    outside_map interface card crypto outside

    ISAKMP allows outside

    ISAKMP key * address 64.X.X.19 netmask 255.255.255.255 No.-xauth-no-config-mode

    ISAKMP identity address

    ISAKMP nat-traversal 20

    part of pre authentication ISAKMP policy 10

    ISAKMP policy 10 3des encryption

    ISAKMP policy 10 md5 hash

    10 2 ISAKMP policy group

    ISAKMP life duration strategy 10 86400

    Site 2 config

    * only because the pt to pt does not work I have it set up to allow vpn clients to cross to connect to the main site.

    Cisco PIX Firewall Version 6.3 (5) *.

    permit access ip 192.168.0.0 list VPN_to_Main 255.255.255.0 10.10.0.0 255.255.0.0

    NAT (inside) 0-list of access VPN_to_Main

    Permitted connection ipsec sysopt

    Crypto ipsec transform-set esp-3des esp-md5-hmac fws_encry_set

    outside_map 10 ipsec-isakmp crypto map

    outside_map card crypto 10 corresponds to the address VPN_to_Main

    crypto outside_map 10 peer 207.X.X.13 card game

    card crypto outside_map 10 transform-set fws_encry_set

    outside_map interface card crypto outside

    ISAKMP allows outside

    ISAKMP key * address 207.X.X.13 netmask 255.255.255.255 No.-xauth-no-config-mode

    ISAKMP identity address

    ISAKMP nat-traversal 20

    part of pre authentication ISAKMP policy 10

    ISAKMP policy 10 3des encryption

    ISAKMP policy 10 md5 hash

    10 2 ISAKMP policy group

    ISAKMP life duration strategy 10 86400

    Errors

    PIX (config) # IPSEC (sa_initiate): ACL = deny; No its created

    authenticator is HMAC-MD5IPSEC (validate_proposal): invalid local address

    I have a link that works very well. I have copied the config from there, changed the ip info and it does not work. The only differences in the configs are no sysopt route dnat and it's on Version 6.2 (2)

    IPSec (sa_initiate): ACL = deny; No its created

    I think that you have configured a VPN tunnel without removing the cryptographic card of the external interface. The message above is the error we get in such situation.

    I suggest the following solution:

    -remove the external interface (the two pix) cryptographic card

    -Cree claire isa his and trendy clear ipsec his (the two pix)

    -Reapply the card encryption on external interfaces.

    If this doesn't solve the problem, restart the equipment.

    Kind regards

    Ajit

  • PIX: Cisco VPN Client connects but no routing

    Hello

    We have a Cisco PIX 515 with software 7.1 (2). He accepts Cisco VPN Client connections with no problems, but no routing does to internal networks directly connected to the PIX. For example, my PC is affected by the IP 172.16.2.57 and then ping does not respond to internal Windows server 172.16.0.12 or trying to RDP. The most irritating thing is that these attempts are recorded in the system log, but always ended with "SYN timeout", as follows:

    2009-01-06 23:23:01 Local4.Info 217.15.42.214% 302013-6-PIX: built 3315917 for incoming TCP connections (172.16.2.57/1283) outside:172.16.2.57/1283 inside: ALAI2 / 3389 (ALAI2/3389)

    2009-01-06 23:23:31 Local4.Info 217.15.42.214% 302014-6-PIX: TCP connection disassembly 3315917 for outside:172.16.2.57/1283 inside: ALAI2 / 3389 duration 0:00:30 bytes 0 SYN Timeout

    2009-01-06 23:23:31 Local4.Debug 217.15.42.214% 7-PIX-609002: duration of disassembly-outside local host: 172.16.2.57 0:00:30

    We tried to activate and deactivate "nat-control", "permit same-security-traffic inter-interface" and "permit same-security-traffic intra-interface", but the results are the same: the VPN connection is successfully established, but remote clients cannot reach the internal servers.

    I enclose the training concerned in order to understand the problem:

    interface Ethernet0

    Speed 100

    full duplex

    nameif outside

    security-level 0

    IP address xx.yy.zz.tt 255.255.255.240

    !

    interface Ethernet1

    nameif inside

    security-level 100

    172.16.0.1 IP address 255.255.255.0

    !

    access extensive list ip 172.16.0.0 inside_nat0_outbound allow 255.255.255.0 172.16.2.56 255.255.255.248

    !

    access extensive list ip 172.16.0.0 outside_cryptomap_dyn_20 allow 255.255.255.0 172.16.2.56 255.255.255.248

    !

    VPN_client_group_splitTunnelAcl list standard access allowed 172.16.0.0 255.255.255.0

    !

    IP local pool pool_vpn_clientes 172.16.2.57 - 172.16.2.62 mask 255.255.255.248

    !

    NAT-control

    Global xx.yy.zz.tt 12 (outside)

    NAT (inside) 0-list of access inside_nat0_outbound

    NAT (inside) 12 172.16.0.12 255.255.255.255

    !

    internal VPN_clientes group strategy

    attributes of Group Policy VPN_clientes

    xxyyzz.NET value by default-field

    internal VPN_client_group group strategy

    attributes of Group Policy VPN_client_group

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list VPN_client_group_splitTunnelAcl

    xxyyzz.local value by default-field

    !

    I join all the details of the cryptographic algorithms because the VPN is successfully completed, as I said at the beginning. In addition, routing tables are irrelevant in my opinion, because the inaccessible hosts are directly connected to the internal LAN of the PIX 515.

    Thank you very much.

    can you confirm asa have NAT traversal allow otherwise, activate it in asa and vpn clients try again.

    PIX / ASA 7.1 and earlier versions

    PIX (config) #isakmp nat-traversal 20

    PIX / ASA 7.2 (1) and later versions

    PIX (config) #crypto isakmp nat-traversal 20

  • PIX VPN problem!

    Hello

    I have currently having problem with vpn, the pix pix506e works fine yesterday, but today morning that the problem appears, the pix did more than 2 connections vpn client, if the user connected, user B will cut this time... If the user B, user A logs off, I write erase config and rebuild again with the base, but still the problem occurs, what could be the problem, software or... material? Here I am attaching my beginning of basic config and vpn client connection.

    Our network is down now... Help, please.

    118 17:07:12.460 12/16/04 Sev = Info/6 IKE/0x6300003D

    Sending DPD asks 218.xxx.xxx.161, seq # = 1257657895

    119 17:07:12.460 12/16/04 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to 218.xxx.xxx.161

    120 17:07:17.468 16/12/04 Sev = Info/6 IKE/0x6300003D

    Sending DPD asks 218.xxx.xxx.161, seq # = 1257657896

    121 17:07:17.468 16/12/04 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to 218.xxx.xxx.161

    122 17:07:22.475 12/16/04 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK INFO *(HASH, DEL) to 218.xxx.xxx.161

    123 17:07:22.475 12/16/04 Sev = Info/5 IKE / 0 x 63000018

    Deleting IPsec security association: (OUTBOUND SPI = 695320B 5 SPI INCOMING = F0A2471)

    124 17:07:22.475 12/16/04 Sev = Info/4 IKE / 0 x 63000048

    IPsec security association negotiation made scrapped, MsgID = 7A8F1E11

    125 17:07:22.475 12/16/04 Sev = Info/4 IKE / 0 x 63000017

    Marking of IKE SA delete (I_Cookie = BAF3D743B1D25DD6 R_Cookie = ED5BAEF920BA3244) reason = DEL_REASON_PEER_NOT_RESPONDING

    126 17:07:22.475 12/16/04 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK INFO *(HASH, DEL) to 218.xxx.xxx.161

    127 17:07:22.475 12/16/04 Sev = Info/4 IPSEC / 0 x 63700013

    Delete the internal key with SPI = 0x71240a0f

    128 17:07:22.475 12/16/04 Sev = Info/4 IPSEC/0x6370000C

    Key removed by SPI 0x71240a0f

    129 17:07:22.475 12/16/04 Sev = Info/4 IPSEC / 0 x 63700013

    Delete the internal key with SPI = 0xb5205369

    130 17:07:22.475 16/12/04 Sev = Info/4 IPSEC/0x6370000C

    Key removed by SPI 0xb5205369

    131 17:07:22.986 12/16/04 Sev = Info/4 IKE/0x6300004A

    IKE negotiation to throw HIS (I_Cookie = BAF3D743B1D25DD6 R_Cookie = ED5BAEF920BA3244) reason = DEL_REASON_PEER_NOT_RESPONDING

    132 17:07:22.986 12/16/04 Sev = Info/4 CM / 0 x 63100013

    ITS phase 1 deleted because of DEL_REASON_PEER_NOT_RESPONDING. 0 ITS phase 1 currently in the system

    133 17:07:22.996 16/12/04 Sev = Info/5 CM / 0 x 63100025

    Initializing CVPNDrv

    134 17:07:23.106 12/16/04 Sev = Info/6 CM / 0 x 63100031

    Head of network device tunnel 218.xxx.xxx.161 disconnected: duration: 0 days 0:16:44

    135 17:07:23.286 16/12/04 Sev = Info/4 IKE / 0 x 63000001

    Signal received IKE to complete the VPN connection

    138 17:07:23.316 12/16/04 Sev = Info/6 CM / 0 x 63100037

    The routing table was returned to the original state before virtual card

    139 17:07:25.649 12/16/04 Sev = Info/4 CM / 0 x 63100035

    The virtual adapter has been disabled

    140 17:07:25.699 16/12/04 Sev = Info/4 IKE / 0 x 63000085

    Service Microsoft's IPSec Policy Agent started successfully

    141 17:07:25.699 16/12/04 Sev = Info/4 IPSEC / 0 x 63700014

    Remove all keys

    142 17:07:25.699 16/12/04 Sev = Info/4 IPSEC / 0 x 63700014

    Remove all keys

    143 17:07:25.699 12/16/04 Sev = Info/4 IPSEC / 0 x 63700014

    Remove all keys

    144 17:07:25.699 12/16/04 Sev = Info/4 IPSEC/0x6370000A

    IPSec driver successfully stopped

    Thank you

    Tonny

    In your PIX, enter the following command:

    ISAKMP nat-traversal

  • Phones AnyConnect VPN cannot connect to network ASA high-speed AT & T uverse

    Phones AnyConnect VPN are configured to connect to the ASA 5510 running 8.4 (4), and it uses the Active Directory credentials to connect. The connection is successful external ISP systems including Comcast and smaller independent service providers. However, when all of us at the AT & T uverse service take this phone 7965 even at home it networks fails to make any connection to the ASA at all. A capture of packets on the ASA shows no activity connection to the IP address of our uverse.

    What's more, is that we can successfully authenticate the VPN of the phone when using the local account credentials (e.g. username admin password * priv 15) that are entered on the SAA. AT & T said that they are not blocking the ports. It is the confusion that this works for users to access local connection, but not with A/D.

    So I guess the question is: what is the first handshake TCP/UDP composed when a Cisco IP phone links AnyConnect SSL to an ASA and negotiates the authentication of the number of A/D? For example, what are the port numbers used in this handshake?  I couldn't find all the diagrams illustrating the HRT and the RFC for DTLS do not seem to have the answer either.

    Thanks in advance.

    -Athonia

    Note: we have a TAC case open currently with subject ASA 5510 VPN Edition w / 250 annyconnect user - SSL VPN for phones. Configuration

    I too ran on this issue and here is a description of what I found.

    If you use automatic network detection first trys phone ping the TFTP server, he has learned from the DHCP server or manually set with the parameter of the alternate TFTP server.  If the TFTP server is accessible the VPN will not connect and will not allow the user to connect manually.

    ATT Uverse use DHCP option 150, the same option as Cisco UC uses to automatically set the TFTP servers, to locate the local home gateway so that the STB can join him.  For this reason, you should notice that when you have a VPN phone on the network and view network settings the IP address of the TFTP server is the IP address of your default gatewat (The ATT router).

    Because of the automatic detection of network works in ping the TFTP server that the phone will always think that it is connected to the local network.  The workaround is to manually set the TFTP server on the phone * to the IP address that the TFTP server would have been if she had leared it from the DHCP server on your corporate network.  The reason you should do this instead of just using a Bogon address, is that once the VPN is connected it tryes to register to the address that you specified.

    Please let me know if this solves your problem as it did in our case.

    * If you do not know how to set the TFTP replacement setting you must first select the "replacement" TFTP protocol and press on * #.  This will allow you to change the default no to Yes.  The below named parameter TFTP Server 1 will then allow you to manually specify the address.

  • Problem connecting to the server

    Whenever I open the pictures, I get an alert that reads: 'there was a problem connecting to the server "my-server", which is another Mac on my network.

    If I close the dialogue box, Photos keeps trying to connect and it appears again a few seconds later.

    Does anyone have an idea as Photos is all this and how I can stop doing?

    No idea - don't forget we can not see you if you have details

    We do not yet have an idea what software you use or you use 'MyServer' for

    What are the versions of the operating system and Photos do you use? What is your server? How are you connected to it?

    LN

  • Problem connecting to the server after moving

    Hi, I keep getting the message "there is a problem connecting to the server"192.168.0.19"etc. This happened after I moved. New ISP, new router. I have an Airport Express and a NAS connected to it. Time Machine and Icloud on the NAS. I think that the NAS has this IP address before moving. There are now 192.168.10.176. Everything works, but I get the pop up frequently.

    I look at the accounts and start but nothing. I reboot safe mode does not remove the problem. So, what can I do?

    I'm on Yosemite with MBR.

    Can you connect using the new IP address?

  • There was a problem connecting to the server 'SERVER NAME' error guard appearing

    There was a problem connecting to the server 'SERVER NAME' error guard appearing even though the server is not on my current network.  I recently moved my iMac to a different location and a different network, and now he constantly tries to connect to the old server.  This message appears every 30 seconds and several of those who appear (see pictures) it's extremely frustrating because it makes the machine almost useless because I am constantly closing them.  No matter how many times I try to stop the activity monitor it it keeps reappearing, and I even tried a few terminal commands that I found online, then restarted the computer, but still had no success.  I would appreciate all the advice really.

    I hope that gives you an idea of what I got!

  • Problems connecting to a site I never had problems before

    Hello
    I don't know if my current problem is related to the LENGTH of the questions that I posted earlier today. This morning I logged on a website as usual, but tonight, I have a problem connecting to. When I can I connect, I can not use the services. First of all, I have a new page greeted me that I've never seen before.

    Another thing, should I say that I don't have the latest FF browser when I click on help == > Feedback. Today, I downloaded the latest version 19.0.2.

    Clear the cache and cookies from sites that cause problems.

    "Clear the Cache":

    • Tools > Options > advanced > network > content caching Web: 'clear now '.

    'Delete Cookies' sites causing problems:

    • Firefox/tools > Options > privacy > Cookies: "show the Cookies".

    If clearing cookies doesn't work, then it is possible that the cookies.sqlite file that stores the cookies is corrupted.

    Rename (or delete) cookies.sqlite (cookies.sqlite.old) and delete other files to present as cookie cookies.sqlite - journal in the profile folder of Firefox in the case where the cookies.sqlite file has been corrupted.

    You can use this button to go to the Firefox profile folder:

    • Help > troubleshooting information > profile directory: see file

  • I have a problem connecting on ebay if you use firefox, I get a message saying that the page does not not despite having cleared my cache and cookies.

    I have a problem connecting on ebay when you use firefox, it has been fine for years, but since a few days, I get a message saying that the page does not when I try to log in. I tried to clear my cookies and cache, but it makes no difference. This does not occur in google chrome and I can log on fine there so what's the problem with firefox?

    Do you also have this problem if you temporarily switch to private browsing mode?

    • Tools > Options > privacy, choose the setting Firefox will: use the custom settings for the story of
    • Select: [X] 'always use private browsing mode '.

    Start Firefox in Firefox to solve the issues in Safe Mode to check if one of the extensions or if hardware acceleration is the cause of the problem (switch to the DEFAULT theme: Firefox/tools > Modules > appearance/themes).

    See also:

Maybe you are looking for