VPN with cisco 2621

Similar Questions

• ISA500 site by site ipsec VPN with Cisco IGR

  Hello

  I tried a VPN site by site work with Openswan and Cisco 2821 router configuration an Ipsec tunnel to site by site with Cisco 2821 and ISA550.

  But without success.

  my config for openswan, just FYI, maybe not importand for this problem

  installation of config

  protostack = netkey

  nat_traversal = yes

  virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12,%4:!$RIGHT_SUBNET

  nhelpers = 0

  Conn rz1

  IKEv2 = no

  type = tunnel

  left = % all

  leftsubnet=192.168.5.0/24

  right =.

  rightsourceip = 192.168.1.2

  rightsubnet=192.168.1.0/24

  Keylife 28800 = s

  ikelifetime 28800 = s

  keyingtries = 3

  AUTH = esp

  ESP = aes128-sha1

  KeyExchange = ike

  authby secret =

  start = auto

  IKE = aes128-sha1; modp1536

  dpdaction = redΘmarrer

  dpddelay = 30

  dpdtimeout = 60

  PFS = No.

  aggrmode = no

  Config Cisco 2821 for dynamic dialin:

  crypto ISAKMP policy 1

  BA aes

  sha hash

  preshared authentication

  Group 5

  lifetime 28800

  !

  card crypto CMAP_1 1-isakmp dynamic ipsec DYNMAP_1

  !

  access-list 102 permit ip 192.168.1.0 0.0.0.255 192.168.5.0 0.0.0.255

  !

  Crypto ipsec transform-set ESP-AES-SHA1 esp - aes esp-sha-hmac

  crypto dynamic-map DYNMAP_1 1

  game of transformation-ESP-AES-SHA1

  match address 102

  !

  ISAKMP crypto key address 0.0.0.0 0.0.0.0

  ISAKMP crypto keepalive 30 periodicals

  !

  life crypto ipsec security association seconds 28800

  !

  interface GigabitEthernet0/0.4002

  card crypto CMAP_1

  !

  I tried ISA550 a config with the same constelations, but without suggesting.

  Anyone has the same problem?

  And had anyone has a tip for me, or has someone expirense with a site-by-site with ISA550 and Cisco 2821 ipsec tunnel?

  I can successfully establish a tunnel between openswan linux server and the isa550.

  Patrick,

  as you can see on newspapers, the software behind ISA is also OpenSWAN

  I have a facility with a 892 SRI running which should be the same as your 29erxx.

  Use your IOS Config dynmap, penny, you are on the average nomad. If you don't have any RW customer you shoul go on IOS "No.-xauth" after the isakmp encryption key.

  Here is my setup, with roardwarrior AND 2, site 2 site.

  session of crypto consignment

  logging crypto ezvpn

  !

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  lifetime 28800

  !

  crypto ISAKMP policy 2

  BA 3des

  md5 hash

  preshared authentication

  Group 2

  lifetime 28800

  !

  crypto ISAKMP policy 3

  BA 3des

  preshared authentication

  Group 2

  !

  crypto ISAKMP policy 4

  BA 3des

  md5 hash

  preshared authentication

  Group 2

  !

  crypto ISAKMP policy 5

  BA 3des

  preshared authentication

  Group 2

  life 7200

  ISAKMP crypto address XXXX XXXXX No.-xauth key

  XXXX XXXX No.-xauth address isakmp encryption key

  !

  ISAKMP crypto client configuration group by default

  key XXXX

  DNS XXXX

  default pool

  ACL easyvpn_client_routes

  PFS

  !

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac FEAT

  !

  dynamic-map crypto VPN 20

  game of transformation-FEAT

  market arriere-route

  !

  !

  card crypto client VPN authentication list by default

  card crypto VPN isakmp authorization list by default

  crypto map VPN client configuration address respond

  10 VPN ipsec-isakmp crypto map

  Description of VPN - 1

  defined peer XXX

  game of transformation-FEAT

  match the address internal_networks_ipsec

  11 VPN ipsec-isakmp crypto map

  VPN-2 description

  defined peer XXX

  game of transformation-FEAT

  PFS group2 Set

  match the address internal_networks_ipsec2

  card crypto 20-isakmp dynamic VPN ipsec VPN

  !

  !

  Michael

  Please note all useful posts

• Order SSL VPN with Cisco Cloud Web Security

  We have implemented Cisco Cloud Web Security with the connector of the ASA and transfer all traffic port 80 and 443 to the Tower of the CCW. We have enabled HTTPS inspection, and I was wondering if there was anything, we can add in the configuration that would allow us to control (allow/block) SSL VPN?

  #Clientless SSL VPN is not supported with Cloud Security Web; don't forget to exempt all SSL VPN traffic without client service ASA for Cloud Web Security Strategy.

  Reference: http://www.cisco.com/c/en/us/td/docs/security/asa/asa90/configuration/gu...

• IPsec VPN with Cisco AnyConnect and 1921 ISR G2 router

  Hello

  Is it possible to establish a remote access VPN IPSec using Cisco Anyconnect client with router Cisco ISR G2 1921.

  If someone does share it please the sample configuration. as I've been on this topic since last week a.

  My Cisco rep recommended I have not try AnyConnect a router ISR or ASR.  So I used an Open Source client.  Don't say that AnyConnect won't work, just the route I took on my project.  I work good known configuration for a 1921 with strongSwan as a Client.  It is with IPSEC and IKEV2 using certificates for authentication.

• PIX IPSec VPN with Cisco 877W

  Hi all

  I am trying to create a VPN between a PIX and a Cisco 877W tunnel but can't seem to get the tunnel. When I do a 'sho crypto session"on the Cisco 877, I get, he said session state is declining, then changed to NEGOTIATE DOWN, but it is now down again... Please find attached the configs for both ends... Are there commands to confirm that the tunnel is up other than to try to ping the remote end? I would greatly appreciate any help lift this tunnel.

  Kind regards

  REDA

  Hello

  Based on the configurations of joined, to do some changes. For example:

  1. the isakmp policies do not match on the router and the pix. Make sure the hash group Diffie-Hellman and life correspond on the 877 and pix.

  2. the access list for the ipsec traffic must be images of mirror of the other.

  3. make sure life of ipsec on the two peers.

  I hope it helps.

  Kind regards

  Arul

  Rate if this can help.

• Cannot connect Cisco 2621 to AWS EC2 Openswan vpn site to site

  Hello, I'm setting up Site to Site vpn between my Cisco 2621 router and Amazon EC2 instance running openswan.
  I get on the following message on the openswan server: 'NO_PROPOSAL_CHOSEN '.
  My router config Cisco 2621 and Openswan config are displayed below, I know im missing something small, but can't
  understand what is :-) any help would be appreciated.

  Apr 16 20:05:55 ip-172-31-1-142.us-west-2.compute.internal pluto [28503]: "paulaga-House" #1: STATE_MAIN_I3: sent MI3, expect MR3
  Apr 16 20:05:55 ip-172-31-1-142.us-west-2.compute.internal pluto [28503]. port/protocol Phase 1 ID payload is 17/0. agreed with port_floating NAT - T
  ' Apr 16 20:05:55 ip-172-31-1-142.us-west-2.compute.internal pluto [28503]: "paulaga-House" #1: hand mode peer ID is ID_IPV4_ADDR: ' 192.168.1.253.
  Apr 16 20:05:55 ip-172-31-1-142.us-west-2.compute.internal pluto [28503]: "paulaga-House" #1: transition of State STATE_MAIN_I3 of State STATE_MAIN_I4
  Apr 16 20:05:55 ip-172-31-1-142.us-west-2.compute.internal pluto [28503]: "House paulaga" #1: STATE_MAIN_I4: ISAKMP Security Association established {auth = PRESHARED_KEY oakley_3des_cbc_192 integ = md5 = MODP1536 group = cipher}
  Apr 16 20:05:55 ip-172-31-1-142.us-west-2.compute.internal pluto [28503]: "paulaga home" #2: quick launch Mode PSK + ENCRYPT + TUNNEL + PFS + UP + IKEV1_ALLOW + IKEV2_ALLOW + SAREF_TRACK + IKE_FRAG_ALLOW {using isakmp #1 proposal of msgid:17d23abf = default pfsgroup = OAKLEY_GROUP_MODP1536}
  Apr 16 20:05:55 ip-172-31-1-142.us-west-2.compute.internal pluto [28503]: "paulaga-House" #1: regardless of the payload information NO_PROPOSAL_CHOSEN, msgid = 00000000, length = 160
  Apr 16 20:05:55 ip-172-31-1-142.us-west-2.compute.internal pluto [28503]. ISAKMP Notification payload
  Apr 16 20:05:55 ip-172-31-1-142.us-west-2.compute.internal pluto [28503].   00 00 00 a0 0e 00 00 00 01 03 04 00
  Apr 16 20:05:55 ip-172-31-1-142.us-west-2.compute.internal pluto [28503]: "paulaga-House" #1: received and ignored the information message

  The schema looks like this:
  192.168.0.0/24:FA0/1[router]FA0/0 192.168.1.253 - 192.168.1.254 [Modem] 64.231.25.93 (pub ip attributed to my modem)

  Cisco 2621 router configuration:

  Current configuration: 2649 bytes
  !
  version 12.3
  no cache Analyzer
  no service timestamps debug uptime
  no service the timestamps don't log uptime
  encryption password service
  !
  cisco2600 hostname
  !
  boot-start-marker
  start the system flash c2600-ik9o3s3 - mz.123 - 26.bin
  boot-end-marker
  !
  logging buffered debugging 10000
  no logging monitor
  !
  No aaa new-model
  IP subnet zero
  IP cef
  !
  !
  name-server IP 192.168.0.10
  !
  Max-events of po verification IP 100
  !

  username admin privilege 15 password 7 01100F175804
  !

  crypto ISAKMP policy 10
  BA 3des
  md5 hash
  preshared authentication
  Group 5
  ISAKMP crypto key mysecretkey address 52.39.49.77
  !
  life crypto ipsec security association seconds 28800
  !
  Crypto ipsec transform-set AMAZON-TRANSFORM-SET esp-3des esp-md5-hmac

  !
  11 INTERNET-CRYPTO ipsec-isakmp crypto map
  ! Incomplete
  description Amazon EC2 instance
  defined by peer 52.39.49.77
  transformation-AMAZON-TRANSFORM-SET game
  match address 111
  !
  !
  !
  !
  interface FastEthernet0/0
  Connection to the Bell Modem description
  IP 192.168.1.253 255.255.255.0
  NAT outside IP
  automatic duplex
  automatic speed
  crypto CRYPTO-INTERNET card
  !
  interface Serial0/0
  no ip address
  !
  interface FastEthernet0/1
  Description of the connection to the local network
  IP 192.168.0.254 255.255.255.0
  192.168.0.10 IP helper-address
  IP nat inside
  automatic duplex
  automatic speed
  No cdp enable
  !
  interface FastEthernet0/1.2
  Service Description Vlan
  encapsulation dot1Q 2
  IP 10.0.0.254 255.0.0.0
  192.168.0.10 IP helper-address
  IP nat inside
  !
  IP nat inside source list ACL - NAT interface FastEthernet0/0 overload
  IP nat inside source static tcp 192.168.0.47 3389 interface FastEthernet0/0 3389
  IP http server
  local IP http authentication
  no ip http secure server
  no ip classless
  IP route 0.0.0.0 0.0.0.0 192.168.1.254
  !
  !!
  !
  !
  extended ACL - NAT IP access list
  allow an ip
  allow a full tcp
  allow a udp
  recording of debug trap
  ease check syslog
  record 192.168.0.47
  access-list 111 allow ip 192.168.0.0 0.0.0.255 172.31.1.0 0.0.0.255
  !
  !
  !
  Dial-peer cor custom
  !
  !
  !
  Line con 0
  password 7 05080F1C2243
  opening of session
  line to 0
  line vty 0 4
  privilege level 15
  local connection
  transport telnet entry
  telnet output transport
  line vty 5 15
  privilege level 15
  local connection
  transport telnet entry
  telnet output transport
  !
  !
  end

  Openswan Configuration:

  file paulaga.secrets:

  64.231.25.93 192.168.1.253 52.39.49.77: PSK "mysecretkey.

  file paulaga.conf:

  Conn paulaga-home
  left = % defaultroute
  subnet # EC2 My leftsubnet=172.31.0.0/16
  leftid = 52.39.49.77 # EC2 my public ip
  right = 64.231.25.93 # My Home Modem public ip
  rightid = router 192.168.1.253 # My Home Cisco 2621 outside interface ip
  rightsubnet=192.168.0.0/24 # My Home LAN Cisco 2621
  authby secret =
  PFS = yes
  start = auto

  Hello

  Since we are getting the following error NO_PROPOSAL_CHOSEN could you please add the following on the router policies then check :

  crypto ISAKMP policy 10
  BA 3des
  md5 hash
  preshared authentication
  Group 5

  crypto ISAKMP policy 20
  BA 3des
  md5 hash
  preshared authentication
  Group 2

  crypto ISAKMP policy 30
  BA 3des
  sha hash
  preshared authentication
  Group 2

  crypto ISAKMP policy 40
  BA aes
  md5 hash
  preshared authentication
  Group 2

  Please test with the latter and keep us informed of the results.

  Kind regards

  Aditya

  Please evaluate the useful messages and mark the correct answers.

• VPN site to Site - Cisco 2621

  Hello

  I want to load an IOS on my Cisco 2621 router. My router is NOT a XM router. My router does not a GOAL card on board. My mem & flash is:

  2621 (MPC860) processor of Cisco (revision 0 x 00) with 61440K / 4096K bytes of memory

  Its my assumption that I do not have a card BUT and that a large part of the map of the GOAL is to make the treatment...

  So, can anyone recommend an IOS that would make a site to ipsec/3des VPN?

  Here's the last IOS with crypto-

  IP/FW/IDS MORE IPSEC 3DES BASIC

  C2600-ik9o3s3 - mz.123 - 26.bin

  Release date: 18 March 2008

  Size: 15706,82 KB (16083780 bytes)

  Minimum memory: DRAM: 64 MB Flash: 16 MB

  Hope that helps.

• AnyConnect + possible PSK (pre-shared key) as under with cisco vpn client ikev1 and ikev2

  Is it possible to create a VPN Anyconnect of RA with just the name of user and password + pre-shared key (Group) for the connection, as could do for ikev1 with cisco VPN client? I am running 8.4.X ASA code and looks like tunnel-group commands have 8.2.X somewhat change. If you change the group type of the tunnel for remote access, now there is no option for IKEv2 PSK. This is only available when you choose the type

  Type of TG_TEST FW1 (config) # tunnel - group?

  set up the mode commands/options:
  Site IPSec IPSec-l2l group
  Remote access using IPSec-IPSec-ra (DEPRECATED) group
  remote access remote access (IPSec and WebVPN) group
  WebVPN WebVPN Group (DEPRECATED)

  FW1(config-tunnel-General) # tunnel - group TG_TEST ipsec-attributes
  FW1(config-tunnel-IPSec) #?

  configuration of the tunnel-group commands:
  any required authorization request users to allow successfully in order to
  Connect (DEPRECATED)
  Allow chain issuing of the certificate
  output attribute tunnel-group IPSec configuration
  mode
  help help for group orders of tunnel configuration
  IKEv1 configure IKEv1
  ISAKMP policy configure ISAKMP
  not to remove a pair of attribute value
  by the peer-id-validate Validate identity of the peer using the peer
  certificate
  negotiation to Enable password update in RADIUS RADIUS with expiry
  authentication (DEPRECATED)

  FW1(config-tunnel-IPSec) # ikev1?

  the tunnel-group-ipsec mode commands/options:
  pre-shared key associate a key shared in advance with the connection policy

  I'm getting old so I hope that it is not in another complaint curmudgeonly on the loss of functionality. :)

  Many small businesses do not want to invest in the PKI. It is usually a pain to deploy, backup, make redundant, etc..

  But it would be nice to have a bit more security on VPN other than just the connections of username and password.

  If this is not possible, it is possible to configure the Anyconnect customer to IKEv1 with PSK and name at the level of the Group client?

  If this is not possible, WTH did cisco end customer VPN cisco as a choice of VPN connection (other than to get more fresh mail of license)?

  I really hope that something like this exists still!

  THX,

  WR

  You are welcome

  In addition to two factors, you can also do double authentication (ie the two using the user name and password). Each set of credentials can come from a Bank of different identities.

  With this scheme, you can can configure a local user name (common) with password on the SAA (think of it as your analog PSK) and the other be the AD user identification information.

• Cisco IOS IPSec failover | Route based VPN with HSRP

  I can find the redundancy of vpn IPSec using policy based VPN with HSRP.

  Any document which ensures redundancy of the road-base-vpn with HSRP?

  OK, I now understand the question. Sorry, I have no documents for this task.

  I can see in the crypto ipsec profile that you will use under the Tunnel interface configuration to enable the protection, you can configure the redundancy:

  cisco(config)#crypto ipsec profile VTIcisco(ipsec-profile)#?Crypto Map configuration commands: default Set a command to its defaults description Description of the crypto map statement policy dialer Dialer related commands exit Exit from crypto map configuration mode no Negate a command or set its defaults redundancy Configure HA for this ipsec profile responder-only Do not initiate SAs from this device set Set values for encryption/decryption

  cisco(ipsec-profile)#redundancy ? WORD Redundancy group name

  cisco(ipsec-profile)#redundancy MRT ? stateful enable stateful failover

  I suggest that it is the same as redundancy card crypto. But no documentation or examples found...

• Cisco 2621 to VPN client problem

  If I ping on the client to the network (behind the router), debug displays the client encryption and decryption of the router. The ping will not, because the router is not encrypt and so the customer is not getting anything to decrypt.

  The Setup is a bit different because the default route is within the network, as it is not the regular internet gateway. I have to add routes for pointing the customer who logs on the internet. Also, one machine uses this as a gateway (using a routemap). To troubleshoot, I removed the routemap custom without result. I think to change the default route, but I don't see how this would have on it.

  Any ideas? Am I missing something?

  Cisco 2621 12.2 (15) T running to the latest version of the client.

  username password XXX 7 XXXXXX

  AAA new-model

  !

  AAA authentication login userauthen local

  AAA authorization groupauthor LAN

  AAA - the id of the joint session

  IP subnet zero

  !

  !

  audit of IP notify Journal

  Max-events of po verification IP 100

  !

  !

  crypto ISAKMP policy 3

  BA 3des

  preshared authentication

  Group 2

  !

  Configuration group customer crypto isakmp XXXX

  key XXXXX

  pool ippool

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

  !

  Crypto-map dynamic dynmap 10

  Set transform-set RIGHT

  !

  map clientmap client to authenticate crypto list userauthen

  card crypto clientmap isakmp authorization list groupauthor

  client configuration address map clientmap crypto answer

  10 ipsec-isakmp crypto map clientmap Dynamics dynmap

  !

  !

  interface Loopback1

  192.168.254.1 IP address 255.255.255.0

  !

  interface FastEthernet0/0

  IP address 200.x.x.x 255.255.x.x

  no ip proxy-arp

  NAT outside IP

  automatic duplex

  automatic speed

  clientmap card crypto

  !

  interface FastEthernet0/1

  the IP 10.0.0.1 255.255.255.0

  no ip proxy-arp

  IP nat inside

  route CUSTOMGATE card intellectual property policy

  automatic duplex

  automatic speed

  !

  IP local pool ippool 10.172.10.100 10.172.10.200

  IP nat inside source map route sheep interface FastEthernet0/0 overload

  no ip address of the http server

  no ip http secure server

  IP classless

  IP route 0.0.0.0 0.0.0.0 10.0.0.30

  access-list 100 deny ip 10.0.0.0 0.0.0.255 10.172.10.0 0.0.0.255

  access-list 100 permit ip 10.0.0.0 0.0.0.255 any

  username password XXX 7 XXXXXX

  AAA new-model

  !

  AAA authentication login userauthen local

  AAA authorization groupauthor LAN

  AAA - the id of the joint session

  IP subnet zero

  !

  !

  audit of IP notify Journal

  Max-events of po verification IP 100

  !

  !

  crypto ISAKMP policy 3

  BA 3des

  preshared authentication

  Group 2

  !

  Configuration group customer crypto isakmp XXXX

  key XXXXX

  pool ippool

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

  !

  Crypto-map dynamic dynmap 10

  Set transform-set RIGHT

  !

  map clientmap client to authenticate crypto list userauthen

  card crypto clientmap isakmp authorization list groupauthor

  client configuration address map clientmap crypto answer

  10 ipsec-isakmp crypto map clientmap Dynamics dynmap

  !

  !

  interface Loopback1

  192.168.254.1 IP address 255.255.255.0

  !

  interface FastEthernet0/0

  IP address 200.x.x.x 255.255.x.x

  no ip proxy-arp

  NAT outside IP

  automatic duplex

  automatic speed

  clientmap card crypto

  !

  interface FastEthernet0/1

  the IP 10.0.0.1 255.255.255.0

  no ip proxy-arp

  IP nat inside

  route CUSTOMGATE card intellectual property policy

  automatic duplex

  automatic speed

  !

  IP local pool ippool 10.172.10.100 10.172.10.200

  IP nat inside source map route sheep interface FastEthernet0/0 overload

  no ip address of the http server

  no ip http secure server

  IP classless

  IP route 0.0.0.0 0.0.0.0 10.0.0.30

  IP route 20.x.x.x 255.255.255.255 200.x.x.x (it is here to let him speak to the customer)

  access-list 100 deny ip 10.0.0.0 0.0.0.255 10.172.10.0 0.0.0.255

  access-list 100 permit ip 10.0.0.0 0.0.0.255 any

  access-list 110 deny host ip 10.0.0.73 10.1.0.0 0.0.0255

  access-list 110 permit ip 10.0.0.73 host everything

  !

  CUSTOMGATE allowed 10 route map

  corresponds to the IP 110

  IP 200.x.x.x next value break

  !

  sheep allowed 10 route map

  corresponds to the IP 100

  !

  !

  CUSTOMGATE allowed 10 route map

  corresponds to the IP 110

  IP 200.x.x.x next value break

  !

  sheep allowed 10 route map

  corresponds to the IP 100

  !

  Add at least:

  > Route ip 10.172.10.0 255.255.255.0 200.x.x.x

  to force the traffic for VPN clients on the external interface. also make sure you hav a route for the clients IP address (not the VPN negotiated one) that also indicates the external interface.

  The fact that the router is not encrypt means that it is not even see the responses from the inside, hosts, which indicates that your internal network is not a road to 10.172.10.0 pointing to this router, OR the router receives responses but sends them back out inside interface which will be set by the first route, I mentioned above.

• Cisco ASA 5510 VPN with PIX 515

  Hello

  I have VPN between Cisco ASA and Cisco PIX.

  I saw in my syslog server this error that appears once a day, more or less:

  Received a package encrypted with any HIS correspondent, drop

  I ve seen issue in another post, but in none of then the solution.

  Here are my files from the firewall configuration:

  Output from the command: 'show running-config '.

  : Saved
  :
  ASA Version 8.2 (1)
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  card crypto WAN_map2 2 corresponds to the address WAN_cryptomap_1
  card crypto WAN_map2 2 set pfs
  card crypto WAN_map2 2 peer 62.80.XX game. XX
  map WAN_map2 2 game of transformation-ESP-DES-MD5 crypto
  card crypto WAN_map2 2 defined security-association 2700 seconds life
  card crypto WAN_map2 2 set nat-t-disable
  card crypto WAN_map2 WAN interface
  enable LAN crypto ISAKMP
  ISAKMP crypto enable WAN
  crypto ISAKMP policy 1
  preshared authentication
  the Encryption
  md5 hash
  Group 5
  lifetime 28800
  No encryption isakmp nat-traversal
  tunnel-group 62.80.XX. XX type ipsec-l2l
  tunnel-group 62.80.XX. IPSec-attributes of XX
  pre-shared-key *.
  

  ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

  8.0 (4) version PIX
  !
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  card encryption VPN_map2 3 corresponds to the address VPN_cryptomap_2
  card encryption VPN_map2 3 set pfs
  card crypto VPN_map2 3 peer 194.30.XX game. XX
  VPN_map2 3 transform-set ESP-DES-MD5 crypto card game
  card encryption VPN_map2 3 defined security-association life seconds 2700
  card encryption VPN_map2 3 set security-association kilobytes of life 4608000
  card VPN_map2 3 set nat-t-disable encryption
  VPN crypto map VPN_map2 interface
  crypto ISAKMP enable VPN
  crypto ISAKMP allow inside
  crypto ISAKMP policy 30
  preshared authentication
  the Encryption
  md5 hash
  Group 5
  lifetime 28800
  No encryption isakmp nat-traversal
  ISAKMP crypto am - disable
  attributes of Group Policy DfltGrpPolicy
  Protocol-tunnel-VPN IPSec
  tunnel-group 194.30.XX. XX type ipsec-l2l
  tunnel-group 194.30.XX. IPSec-attributes of XX
  pre-shared-key *.
  

  If you need more information dedailed ask me questions.

  Thanks in advance for your help.

  Javi

  Hi Javi,

  Please after the release of "see broadcasting DfltGrpPolicy of any political group." See if you have the "vpn-idle-timoeout" command configured in that. If so, please change to "vpn-idle-timeout no" and see if that stops at these popping up error messages.

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/command/reference/uz.html#wp1571426

  Thank you and best regards,

  Assia

• question links to site 2 site VPN with authentication cert

  Currently we are accumulate tunnel site-2-site VPN with our client. Usually we use pre-shared key as authentication with other customers without any problems, but it must use authentication cert with her this time. But the question is that our CA is different from theirs. I tried a few times, but he failed. Is it someone please let me know that he must have the certificate issued by the same certification authority to create the VPN tunnel?

  Thank you very much!

  Hello

  You can read this document to get a simple example of setting up a VPN S2S using certificates on an ASA:

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080aa5be1.shtml

  Basically the sides must have the same certification authority and If there is an intermediate certificate that must be installed also. The ASA 2 will generate a CSR (certificate access code request), now then PKI will create a certificate for both parties, commonly called "certificate of identity".

  Please pass a note and mark as he corrected the post helpful!

  David Castro,

  Kind regards

• Rejection of authentication: unspecified - Concentrator VPN with MS Radius

  Please,

  I'm trying to connect with Cisco VPN Client using MS Radius, but the message appears: rejection of authentication: unspecified.

  I tried also to use the option [x] do not held pre-authentication, but don t work of cisco_vpn_msradius.pdf guide - troubleshooting.

  VPN concentrator - Administration of the ping test is ok for the server Radius Ms.

  I see the newspapers and the only other thing that appear is the error of payload.

  Thank you very much

  You can check that your group has PAP as authentication under the PPP attributes Protocol? So if you have newspapers of som on the event viewer on the windows box please share them here.

• Client VPN und Cisco asa 5505 tunnel work but no traffic

  Hi all

  I am new to this forum and Don t have a lot of experience with Cisco, so I hope I can get help from specialists.

  I have the following problem:

  I installed und konfigured ASA 5505 for use with vpn client. I would like to access the local network from outside through vpn.

  To test, I installed ASA 5505 with ADSL (pppoe) and tried to give access to the internal network.

  Of course whenever I have recive the supplier's different IP address, but it didn't is not a problem reconfigure in the vpn client.

  After the connection is established (vpn tunnel work) I can see my external network packets. But I Don t have any connection to the internal network.

  I erased my setup yesterday and tried to reconfigure ASA again. I didn t tested yesterday, because it was too late. And I know that I Don t have the authorization rule at present by the ACL. But I think I'm having the same problem again. (tunnel but no traffic).

  What I did wrong. Could someone let me know what I have to do today.

  With hope for your help Dimitri.

  ASA configuration after reset and basic configuration: works to the Internet from within the course.

  : Saved

  : Written by enable_15 to the CEDT 20:29:18.909 Sunday, August 29, 2010

  !

  ASA Version 8.2 (2)

  !

  ciscoasa hostname

  activate 2KFQnbNIdI.2KYOU encrypted password

  2KFQnbNIdI.2KYOU encrypted passwd

  names of

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  PPPoE client vpdn group home

  IP address pppoe setroute

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  boot system Disk0: / asa822 - k8.bin

  passive FTP mode

  clock timezone THATS 1

  clock to summer time CEDT recurring last Sun Mar 02:00 last Sun Oct 03:00

  DNS domain-lookup outside

  DNS server-group DefaultDNS

  Server name 194.25.0.60

  Server name 194.25.0.68

  DM_INLINE_TCP_1 tcp service object-group

  port-object eq www

  EQ object of the https port

  inside_access_in list extended access permitted udp 192.168.1.0 255.255.255.0 no matter what eq field open a debug session

  inside_access_in list extended access permitted tcp 192.168.1.0 255.255.255.0 any object-group DM_INLINE_TCP_1 open a debug session

  inside_access_in list extended access deny ip any any debug log

  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.0.0 255.255.0.0

  permit inside_nat0_outbound to access extended list ip 192.168.10.0 255.255.255.0 192.168.10.0 255.255.255.128

  homegroup_splitTunnelAcl list standard access allowed 192.168.10.0 255.255.255.0

  pager lines 24

  Enable logging

  asdm of logging of information

  Outside 1500 MTU

  Within 1500 MTU

  IP local pool homepool 192.168.10.1 - 192.168.10.100 mask 255.255.255.0

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm-625 - 53.bin

  ASDM location 192.168.0.0 255.255.0.0 inside

  ASDM location 192.168.10.0 255.255.255.0 inside

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  inside_access_in access to the interface inside group

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  dynamic-access-policy-registration DfltAccessPolicy

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  VPDN group home request dialout pppoe

  VPDN group House localname 04152886790

  VPDN group House ppp authentication PAP

  VPDN username 04152886790 password 1

  dhcpd outside auto_config

  !

  dhcpd address 192.168.1.5 - 192.168.1.36 inside

  dhcpd allow inside

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  TFTP server 192.168.1.5 inside c:/tftp-root

  WebVPN

  Group Policy inner residential group

  attributes of the strategy of group home group

  value of 192.168.1.1 DNS server

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list homegroup_splitTunnelAcl

  username user01 encrypted password privilege 0 v5P40l1UGvtJa7Nn

  user01 username attributes

  VPN-strategy group home group

  tunnel-group home group type remote access

  attributes global-tunnel-group home group

  address homepool pool

  Group Policy - by default-homegroup

  tunnel-group group residential ipsec-attributes

  pre-shared-key ciscotest

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  context of prompt hostname

  Cryptochecksum:930e6cddf25838e47ef9633dc2f07acb

  : end

  Hello

  Normally, you want a static public IP address on the ASA to allow it to receive connections from VPN clients (avoid to change the IP address all the time).

  If you connect via VPN, check the following:

  1. the tunnel is established:

  HS cry isa his

  Must say QM_IDLE or MM_ACTIVE

  2 traffic is flowing (encrypted/decrypted):

  HS cry ips its

  3. Enter the command:

  management-access inside

  And check if you can PING the inside ASA VPN client IP.

  4. check that the default gateway for the LAN internal ASA within intellectual property (or there is a road to the ASA to send traffic to the VPN clients).

  Federico.

• ASA vpn with a public ip address different addresses

  Hello world. I can not find someone who can give me an answer 'for sure' of this thing. I want to connect via vpn ASA5505, called 2A and b. inside one we have net 10.0.0.0/24 and 10.0.1.0/24 net b. now, we can have 2 outside for one ip addresses (e.g. 215.18.18.10 and 222.26.12.12) because we have 2 providers to connect to the internet. the asa can follow 2 VPN - with the same cryptomap for the destination inside) so that if a grave he will switch to the other vpn by itself?

  This thing can be done with other cisco devices (for example, a 2800 series router?)

  Thank you very much

  Who are you looking to

  1. If the failure of the connection to B then A will use secondary WAN connection to try to raise the tunnel.

  I would use the backup ISP for this function.

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00806e880b.shtml

  2. If the connection to A failed then B will try to set up the tunnel with secondary address peer.

  You can set several counterparts by using cryptographic cards to provide redundancy

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_guide_chapter09186a0080450b73.html#wp1042941