VPN with dynamic IP. How to use DNS?

Similar Questions

• ASA - s2s vpn with dynamic ip - Dungeon tunnel upward

  Hi guys,.

  We want to set up a vpn between our central asa5520, and a new branch office asa5505 with dynamic public ip address.

  This type of configuration is supported, but the tunnel can only be initiated from the asa distance (the asa central do not know how to reach the asa remote).

  prove that on this vpn also transit traffic voice, we must always maintain the tunnel.

  A solution would be to have a kind of continuous ping from the remote office to the central office... is more 'professional' wat to reach our goal?

  Thank you.

  Try, 'management-access to the inside' of the asa and ping

• SSL VPN with dynamic IP

  Hello

  I want to configure a VPN SSL on an international search report which is to obtain a dynamic IP address from the ISP. I know that the static configuration using IP. How to configure this to a dynamic IP address?

  Kind regards
  Tony

  Hello Tony,.

  Just because u asked him

  Use the following syntax:

  WebVPN gateway x.x.x

  port IP interface giga 0 443

  In this case u get public ip address on giga 0,

  Be sure to note all the useful messages.

  For this community, which is as important as a thank you.

• SG300-28 - Firmware 1.2.7.76 with the MAC: how to use the VLAN? (Bugs00131469)

  Hallo,

  can you please explain to me this problem more in detail, please:

  ##################################################################

  Problem: When a port Transceiver allowed tent of to re-authenticate and RADIUS

  attributes no longer target attributes VLAN, re-authentication breaks down and the

  port must become unauthorized. This is not the case, and the port is not.

  (Bugs00131469)

  Solution: Do not delete attributes of VLANS on a RADIUS server or unplug

  network cable and plug it in again to force the failure.

  ##################################################################

  I use an assignment VLAN dynamic for my known hosts of the network (authentication MAC) based only. But there are people from other companies who use their own computer and this computer does not know on my RADIUS server. These people should use the VLAN comments. In general they disconnect the LAN cable from a host that is known on my SHELF and put the LAN cable into their laptop (which is not known by the RADIUS server).

  Does this mean that this port will remain in the VLAN old or the switch will change the port the the guest VLAN?

  And what happens if I reconnect the computer to know about this port?

  This feature is very important to me, but I need the functionality of the new firmware RADIUS accounting. So please give me some advice!

  Thank you very much!

  Alexander Wilke

  Hello, Alexander.

  When connecting to an unknown host to the switch, it should go to a VLAN authenticated or if you use the VLAN comments, it must be created statically a VLAN on the switch. With the comments-VLAN-Enable, the switch automatically assigns a port as a member not marked. When the port is allowed, the switch will have to move the port to VLAN comments when the first applicant authorizes.

  Basically, this bug listed above says not to make changes to your information RADIUS server of VLAN and if you do, unplug the network and reconnect it.

  -Tom

• MUSE, accommodation in British Colombia with secure server - how to use?

  I can access my domain using the address of root for the Secure Server Business Catalyst, works very well. Now, how can I link my page Please contact us , including the contact form so that the page opens to the secure server. Is this possible with the MUSE? Thank you.

  yourBCsitename.worldsecuresystems.com/yourpagename.html

• ASA ASA Site2Site VPN with dynamic NAT in version 8.2

  I did everything for NAT to 9.x and I don't have much at all with NAT in 8.2 and earlier with this configuration.

  I have some local subnets:

  172.30.1.0/24
  172.30.16.0/24
  172.30.3.0/24
  172.30.12.0/24
  172.30.7.0/24
  172.30.35.0/24

  who will need to access a remote subnet:

  10.31.255.128/25

  and the requirement is to NAT the following text:

  A lot of requirement much NAT.
  172.30.1.0/24 NAT at 192.168.104.0/24
  172.30.16.0/24 NAT at 192.168.105.0/24
  172.30.3.0/24 NAT at 192.168.108.0/24
  172.30.12.0/24 NAT at 192.168.106.0/24
  172.30.7.0/24 NAT at 192.168.107.0/24
  172.30.35.0/24 NAT at 192.168.103.0/24

  When you go to the 10.31.255.128/25 subnet.

  Here's what I think, I need and I'm looking for confirmation and/or messages.

  Config group *.

  object-group, LAN using a NAT-NETWORKS
  192.168.104.0 subnet 255.255.255.0
  192.168.105.0 subnet 255.255.255.0
  192.168.108.0 subnet 255.255.255.0
  192.168.106.0 subnet 255.255.255.0
  192.168.107.0 subnet 255.255.255.0
  192.168.103.0 subnet 255.255.255.0

  Group of objects to REMOTE-network
  subnet 10.31.255.128 255.255.255.128

  ACL for the crypto-card *.

  REMOTE_cryptomap_72 list extended access permitted ip object-group LOCAL-using a NAT-NETWORKS-group of objects to REMOTE-NETWORK

  Config NAT

  NAT (inside) 10 172.30.1.0 255.255.255.0
  NAT (inside) 20 172.30.16.0 255.255.255.0
  NAT (inside) 30 172.30.3.0 255.255.255.0
  NAT (inside) 40 172.30.12.0 255.255.255.0
  NAT (inside) 50 172.30.7.0 255.255.255.0
  NAT (inside) 60 172.30.35.0 255.255.255.0

  Global (outside) 10 192.168.104.0 255.255.255.0
  Global (outside) 20 192.168.105.0 255.255.255.0
  Global (outside) 30 192.168.108.0 255.255.255.0
  Global (outside) 40 192.168.106.0 255.255.255.0
  Global (outside) 50 192.168.107.0 255.255.255.0
  Global (outside) 60 192.168.103.0 255.255.255.0

  This sets up the set of transformation which is called in the Crypto map.* *.

  Crypto ipsec transform-set ikev1 REMOTE-SET esp-3des esp-sha-hmac

  This sets up the Crypto map.* *.

  address for correspondence card crypto outside_map 72 REMOTE_cryptomap_72
  peer set card crypto outside_map 72 5.5.5.4
  card crypto outside_map 72 set transform-set REMOTE-SET ikev1
  outside_map card crypto 72 the value reverse-road

  Implements IKE *.

  IKEv1 crypto policy 72
  sha hash
  preshared authentication
  Group 2
  lifetime 28800
  3des encryption

  Sets up the Group of tunnel (connection profile) *.

  tunnel-group 5.5.5.4 type ipsec-l2l
  IPSec-attributes tunnel-group 5.5.5.4
  IKEv1 pre-shared-key * TBD *.

  Thank you

  Mike

  With your existing global declarations, my suggestion should meet the requirement. Here is some additional info: http://www.cisco.com/c/en/us/td/docs/security/asa/asa82/configuration/gu...

• IPSEC VPN with Dynamics to dynamic IP

  Hello

  I tried IPSEC VPN with dynamic IP to dynamic (router to router) for some time. But still can not auto-établir the tunnel.

  Is someone can you please tell me if it is possible to do?

  If so, please share with me the secret to do work.

  Thank you!

  Best regards

  Rather than the Crypto map, I would use the profile of Crypto.  Then, establish you an IPSEC tunnel.  The beauty of the profile, is that you can run through it routing protocols, and you do not have to change constantly the cards whenever you change the topology of the network.  The "* * *" in the timer event is "minute hour day week month" so "* * *" is updated every minute.  In Tunnel destination, it's an IP address, not a hostname that is stored, but when you set it, you can put in a HOST name and it converts to the moment where you configure it to an IP address.

  So, if you type:

  config t

  interface tunnel100
  destination remote.dyndns.com tunnel

  output

  See the race int tunnel100

  It shows:

  interface Tunnel100
  tunnel destination 75.67.43.79

  That's why the event handler goes and becomes the destination of tunnel every minute what ever the DDNS says that is the new IP address.

  I have seen that two of your routers running DDNS.  They will have to do this.

  Local router:

  crypto ISAKMP policy 1
  BA aes 256
  preshared authentication
  Group 2
  ISAKMP crypto key XXXXXXX address 0.0.0.0 0.0.0.0 no.-xauth
  !
  !
  Crypto ipsec transform-set ESP-AES-SHA esp - aes 256 esp-sha-hmac
  !
  Profile of crypto ipsec CRYPTOPROFILE
  game of transformation-ESP-AES-SHA
  !
  interface Tunnel100
  Description of remote.dyndns.org
  IP 10.254.220.10 255.255.255.252
  IP virtual-reassembly
  IP tcp adjust-mss 1400
  source of Dialer0 tunnel
  tunnel destination 75.67.43.79
  ipv4 ipsec tunnel mode
  Tunnel CRYPTOPROFILE ipsec protection profile

  IP route 192.168.2.0 255.255.255.0 10.254.220.9

  Change-tunnel-dest applet event handler
  cron-event entry timer cron name "CHRON" * * *"
  command action 1.0 cli 'enable '.
  action 1.1 cli command "configures terminal.
  Action 1.2 command cli "interface tunnel100".
  Action 1.3 cli command "destination remote.dyndns.org tunnel".
  !

  --------

  Remote router:

  crypto ISAKMP policy 1
  BA aes 256
  preshared authentication
  Group 2
  ISAKMP crypto key XXXXXXX address 0.0.0.0 0.0.0.0 no.-xauth
  !
  !
  Crypto ipsec transform-set ESP-AES-SHA esp - aes 256 esp-sha-hmac
  !
  Profile of crypto ipsec CRYPTOPROFILE
  game of transformation-ESP-AES-SHA
  !
  interface Tunnel100
  Description of local.dyndns.org
  IP 10.254.220.9 255.255.255.252
  IP virtual-reassembly
  IP tcp adjust-mss 1400
  source of Dialer0 tunnel
  tunnel destination 93.219.58.191
  ipv4 ipsec tunnel mode
  Tunnel CRYPTOPROFILE ipsec protection profile

  IP route 192.168.1.0 255.255.255.0 10.254.220.10

  Change-tunnel-dest applet event handler
  cron-event entry timer cron name "CHRON" * * *"
  command action 1.0 cli 'enable '.
  action 1.1 cli command "configures terminal.
  Action 1.2 command cli "interface tunnel100".
  Action 1.3 cli command "destination local.dyndns.org tunnel".

  Thank you

  Bert

• CD, how to make the CD to play? It's a CD with instructions on how to install my printer.

  How to make a CD to play?  It's a CD with instructions on how to install my printer

  Insert the CD in your optical drive (if you have a DVD or CD drive)

  The CD should auto run and invites you to play or open the disk.

  If it isn't, try the following:

  Click Start > computer > open disk > and double click on the installation file or the MSI installer.

  The disc should come with instructions on how to use it.

• AMPe ADF with Dynamic tab Shell not made in iPAD 1 +.

  Hello
  
  We used the Oracle Dynamic tab Shell templates to build our page of dashboard with several dynamic tabs.
  A year back when we have initially created the main dashboard with Dynamic tab Shell and used of the UIShell API to open new dynamic tab when clicking the command links in the browser side of left hand. We started with Jdev 11.1.1.3 and upgrade us until Jdev 11.1.1.5.
  
  Now this last requirement is, we need to test our applications in the Safari browser in iPAD (2.0). During the test, we observed under questions.
  
  (1) the page with Dynamic tab Shell JSPX is keep showing "Loading"... "We had updated the Safari browser twice to render the page.
  (2) any af:commandLink under the JSPX which has shell model dynamic tab, does not. We have lots of links on the left navigation and when clicking on each link will open a new tab dynamic (we use UIShell API). Nothing happens when clicking on these af:commandLinks.
  (3) we have 'Home' and 'Logout' links at the top right. Nothing happens on the links click too.
  
  All these as af:commandLinks and af:commandButtons not working as expected when we have them beside a JSPX page without shell dynamic tab.
  
  Tested and observed the same behavior both in version 1.0 and newer iPad iPAD 2.0.
  We desperately need help on thin. Pls let us know, if I need to provide more details. Are there specific configurations required to make it work in Jdev 11.1.1.5? At this stage we cannot improve our Env 11.1.1.6 or 11.1.2 as we already have these applications in Production and we should give users flexibility to be used in the iPAD.
  
  Help, please!
  
  Thank you!!
  Subba.

  Subba,

  I understand, however support for iPad added in PS5 is a set of new features, not a bug fix, so this cannot be claimed as a one off patch with the support of the Oracle. In this case that is expected to capture customers highlights new features of upgrade.

  Thank you

• How to establish a tunnel vpn ipsec using DNS with ASA 5505?

  Hello

  I m get a dynamic IP address public and what I m trying to do is establish a tunnnel remote vpn using IPSec, which I realize my provider but each time resets of sessions or ASA 5505 reset, I get a new public IP and I need to put the new IP address on the remote client, so I can establish the vpn...

  How can I establish a vpn ipsec using DNS?  For this scenario, the remote client vpn is a vpn phone, but it could be any vpn client.

  Private private Public IP IP IP

  PBX - Telephone (LAN) - ASA 5505-(Internet)-(router) Remote Site-(LAN) VPN-

  Kind regards!

  Ah ok I see, Yes in this case there is no that you can do other than request a static IP address from your ISP.

  Kind regards.

  PS: Don't forget to mark this question as answered. Thank you!

• Im trying to open the tutorial of 23 minutes on how to use different tools in photoshop and it continues to come with unable to resolve the DNS servers worked fine yesterday? Ive had creative cloud on my laptop for a week and still have not been able t

  Im trying to open the tutorial of 23 minutes on how to use different tools in photoshop and it continues to come with unable to resolve the DNS servers worked fine yesterday? Ive had creative cloud on my laptop for a week and not yet able to get past the basics make me very frustrated.

  I guess you meant the links when you open photoshop CC. I tested all four videos of the 23 min tutorial and they all played fine. If something between you and adobe does not work correctly.

  • Check that your firewall is blocking the net. Try to access youtube videos and see if they play very well
  • Go to the adobe tv site and try to play one of the videos here. Adobe TV
  • If youtube plays very well and adobe tv does not work, next is to check if you have flash installed. Some videos require flash, others are html 5. Sorry that I could not confirm what player has been used for this tutorial. I think that html 5 but not sure.
  • Next is to look at the properties of your browser and check multimedia settings are not disabled if it y in a. (this is totally dependent on the browser)

  If none of this helps, let us know.

• ASA to remote access VPN with external IP dynamic

  Hi forum,

  I was wondering if it was possible to set up an ASA to provide access to remote connections VPN (IPSEC or WebVPN/SSL) of the outside world, if the external IP address is dynamic (i.e. obtained through DHCP)?  I understand how to use DynamicDNS to provide a host name for the VPN clients, I ask simply if the SAA can be configured to allow VPN connections from a DHCP interface addressed.  I understand there are problems with the site to site VPN when both sides are addressed in a dynamic way, but it seems that the remote VPN access should work.  Just hoping to confirm this before I go and I'm working on a config.

  Thanks in advance...

  The same configuration applies.

  In my view, that the only difference is that with the external IP being dynamic:

  interface e0/0

  IP address dhcp setroute

  crypto map

  The only difference is that (the PCF file) VPN clients should have the VPN connection with a hostname (rather than an IP address) and the IP must be solved at the IPs of the SAA.

  I'll try to find you an example configuration if you do not.

  Federico.

• Remote access VPN with ASA 5510 by using the DHCP server

  Hello

  Can someone please share your knowledge to help me find out why I'm not able to receive an IP address on the remote access VPN connection so that I can get an IP local pool DHCP?

  I'm trying to set up remote access VPN with ASA 5510. It works with dhcp local pool but does not seem to work when I tried to use an existing DHCP server. It is tested in an internal network as follows:

  !

  ASA Version 8.2 (5)

  !

  interface Ethernet0/1

  nameif inside

  security-level 100

  IP 10.6.0.12 255.255.254.0

  !

  IP local pool testpool 10.6.240.150 - 10.6.240.159 a mask of 255.255.248.0. (worked with it)

  !

  Route inside 0.0.0.0 0.0.0.0 10.6.0.1 1

  !

  Crypto ipsec transform-set esp-3des esp-md5-hmac FirstSet

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  Crypto-map dynamic dyn1 1jeu transform-set FirstSet

  dynamic mymap 1 dyn1 ipsec-isakmp crypto map

  mymap map crypto inside interface

  crypto ISAKMP allow inside

  crypto ISAKMP policy 1

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 43200

  !

  VPN-addr-assign aaa

  VPN-addr-assign dhcp

  !

  internal group testgroup strategy

  testgroup group policy attributes

  DHCP-network-scope 10.6.192.1

  enable IPSec-udp

  IPSec-udp-port 10000

  !

  username testlay password * encrypted

  !

  tunnel-group testgroup type remote access

  tunnel-group testgroup General attributes

  strategy-group-by default testgroup

  DHCP-server 10.6.20.3

  testgroup group tunnel ipsec-attributes

  pre-shared key *.

  !

  I got following output when I test connect to the ASA with Cisco VPN client 5.0

  Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: (4) SA (1) + KE + NUNCIO (10) + ID (5), HDR + VENDO

  4024 bytesR copied in 3,41 0 seconds (1341 by(tes/sec) 13) of the SELLER (13) seller (13) + the SELLER (13), as well as the SELLER (13) ++ (0) NONE total length: 853

  Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, SA payload processing

  Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing ke payload

  Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing ISA_KE

  Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, nonce payload processing

  Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing ID

  Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID

  Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received xauth V6 VID

  Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID

  Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, DPD received VID

  Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID

  Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received Fragmentation VID

  Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, IKE Peer included IKE fragmentation capability flags: Main Mode: real aggressive Mode: false

  Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID

  Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received NAT-Traversal worm 02 VID

  Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID

  Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, the customer has received Cisco Unity VID

  Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, connection landed on tunnel_group testgroup

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA payload processing

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA proposal # 1, turn # 9 entry overall IKE acceptable matches # 1

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build the payloads of ISAKMP security

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building ke payload

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building nonce payload

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Generating keys for answering machine...

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, construction of payload ID

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of hash

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash for ISAKMP

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of Cisco Unity VID

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing payload V6 VID xauth

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building dpd vid payload

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing the payload of the NAT-Traversal VID ver 02

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, NAT-discovery payload construction

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, NAT-discovery payload construction

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, construction of Fragmentation VID + load useful functionality

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads VID

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, send Altiga/Cisco VPN3000/Cisco ASA GW VID

  Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 0) with payloads: HDR SA (1) KE (4) NUNCIO (10) + ID (5) + HASH (8) + SELLER (13) + the SELLER (13) + the SELLER (13) + the SELLER (13) NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + NONE (0) total length: 440

  Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR + HASH (8) + NOTIFY (11) + NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + NONE (0) overall length: 168

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing hash payload

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash for ISAKMP

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing notify payload

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload NAT-discovery of treatment

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload NAT-discovery of treatment

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload processing VID

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, useful treatment IOS/PIX Vendor ID (version: 1.0.0 capabilities: 00000408)

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload processing VID

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, the customer has received Cisco Unity VID

  Jan 16 15:39:21 [IKEv1]: Group = testgroup, I

  [OK]

  KenS-mgmt-012 # P = 10.15.200.108, status of automatic NAT detection: remote end is NOT behind a NAT device this end is NOT behind a NAT device

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, empty building hash payload

  Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of hash qm

  Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = d4ca48e4) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 72

  Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = d4ca48e4) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 87

  Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, process_attr(): enter!

  Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, transformation MODE_CFG response attributes.

  Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: primary DNS = authorized

  Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: secondary DNS = authorized

  Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: = authorized primary WINS

  Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: = authorized secondary WINS

  Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Compression IP = disabled

  Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Split Tunneling political = disabled

  Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: setting Proxy browser = no - modify

  Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: browser Local Proxy bypass = disable

  Jan 16 15:39:26 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, (testlay) the authenticated user.

  Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, empty building hash payload

  Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, build payloads of hash qm

  Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 6b1b471) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 64

  Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 6b1b471) with payloads: HDR + HASH (8) + ATTR (14) + NONE (0) overall length: 60

  Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): enter!

  Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, cfg ACK processing attributes

  Jan 16 15:39:27 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 49ae1bb8) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 182

  Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): enter!

  Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, treatment cfg request attributes

  Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the IPV4 address!

  Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the IPV4 network mask!

  Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for DNS server address.

  Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the address of the WINS server.

  Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, transaction mode attribute unhandled received: 5

  Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the banner!

  Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for setting save PW!

  Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: receipt of request for default domain name!

  Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for Split-Tunnel list!

  Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for split DNS!

  Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for PFS setting!

  Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the Proxy Client browser setting!

  Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the list of backup peer ip - sec!

  Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for setting disconnect from the Client Smartcard Removal!

  Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the Version of the Application.

  Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Type of Client: Windows NT Client Application Version: 5.0.07.0440

  Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for FWTYPE!

  Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: request received for the DHCP for DDNS hostname is: DEC20128!

  Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the UDP Port!

  Jan 16 15:39:32 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, in double Phase 2 detected packets.  No last packet retransmit.

  Jan 16 15:39:37 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = b04e830f) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84

  Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing hash payload

  Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing notify payload

  Jan 16 15:39:37 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, in double Phase 2 detected packets.  No last packet retransmit.

  Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE has received the response from type [] at the request of the utility of IP address

  Jan 16 15:39:39 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, cannot get an IP address for the remote peer

  Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, case of mistaken IKE TM V6 WSF (struct & 0xd8030048) , : TM_DONE, EV_ERROR--> TM_BLD_REPLY, EV_IP_FAIL--> TM_BLD_REPLY NullEvent--> TM_BLD_REPLY, EV_GET_IP--> TM_BLD_REPLY, EV_NEED_IP--> TM_WAIT_REQ, EV_PROC_MSG--> TM_WAIT_REQ, EV_HASH_OK--> TM_WAIT_REQ, NullEvent

  Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, case of mistaken IKE AM Responder WSF (struct & 0xd82b6740) , : AM_DONE, EV_ERROR--> AM_TM_INIT_MODECFG_V6H, EV_TM_FAIL--> AM_TM_INIT_MODECFG_V6H NullEvent--> AM_TM_INIT_MODECFG, EV_WAIT--> AM_TM_INIT_XAUTH_V6H, EV_CHECK_QM_MSG--> AM_TM_INIT_XAUTH_V6H, EV_TM_XAUTH_OK--> AM_TM_INIT_XAUTH_V6H NullEvent--> AM_TM_INIT_XAUTH_V6H, EV_ACTIVATE_NEW_SA

  Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE SA AM:bd3a9a4b ending: 0x0945c001, refcnt flags 0, tuncnt 0

  Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, sending clear/delete with the message of reason

  Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, empty building hash payload

  Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing the payload to delete IKE

  Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, build payloads of hash qm

  Jan 16 15:39:39 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 9de30522) with payloads: HDR HASH (8) + DELETE (12) + (0) NONE total length: 80

  Kind regards

  Lay

  For the RADIUS, you need a definition of server-aaa:

  Protocol AAA - NPS RADIUS server RADIUS

  AAA-server RADIUS NPS (inside) host 10.10.18.12

  key *.

  authentication port 1812

  accounting-port 1813

  and tell your tunnel-group for this server:

  General-attributes of VPN Tunnel-group

  Group-NPS LOCAL RADIUS authentication server

  --
  Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
  http://www.Kiva.org/invitedBy/karsteni

• How to bind a VPN (TX via VPN) with a sat (RX via DVB - S2) / Windows Vista Home Edition / Multiple dial conections

  I use a Windows Vista Home Edition on a laptop. The system connects to the Internet through a cellular router EDGE (via Ethernet) and receives the data by linking receiver DVB - S2 satellite broadband connected via a USB interface. The connection is through a VPN. Windows Vista loses the symbol of the "blue planet", as soon as the VPN connects. Authentication and connectivity is OK. DNS also works OK by the way VPN, with pointing to the VPN IP address 0.0.0.0.  The diagnosis indicates an error where Vista says that she finds multiple active dial connections. Y at - it a configuration option that allows me to bind the interface transmission (VPN) with return channel satellite?  The same software and configuration under Windows XP SP3 works OK.

  Thanks in advance for your advice.

  Hello

  Your question of Windows 7 is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the Technet Forum. You can follow the link to your question:
  http://social.technet.Microsoft.com/forums/en-us/category/w7itpro

  You can also check the links below for assistance.

  http://TechNet.Microsoft.com/en-us/library/cc728078 (WS.10) .aspx

  http://TechNet.Microsoft.com/en-us/library/cc737767 (WS.10) .aspx

  Hope that helps.

• How to create vpn with vista home premium on basis of vpn xp settings?

  I can connect to the vpn with xp machine, but when I try to imitate xp setting with machine to vista Home premium I can't connect to the same vpn. What do you suggest me?

  How to create a vpn connection in Vista: http://techrepublic.com.com/2346-1035_11-61437-1.html?tag=content;leftCol.  NOTE: I don't know what you mean "based" vpn xp settings, but you will have to do the best you can with the options and settings available in Vista (that I n "' t know how they compare to XP, but I hope that you will be able to do so because).

  Here is another article on the procedure: http://www.publicvpn.com/support/Vista.php.

  Here is an article on how configure a VPN with an ISP in Vista: http://www.web-articles.info/e/a/title/How-to-create-a-VPN-connection-over-your-ISP-connection/.

  Here is an article with a number of different other items all on vpn in Vista (I don't know exactly what type of configuration you "AVIC - as a host, as a customer, on what type of connection,--but this article covers many different aspects and I hope that at least a couple will be a help for you: http://compnetworking.about.com/od/vpnsetup/VPN_Setup_How_to_Set_Up_a_VPN.htm.)

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.