vSphetre Client - option problem

Similar Questions

• Issue LDAP Primavera 8.1 with the Client optionally

  We managed to setup the web access LDAP client. But we are unable to connect from the client optionally using LDAP accounts.
  
  The erorr that we get is
  Name of invalid user or password. Please try again or click Cancel to exit the application.
  Cannot bind to the object
  LDAP://XXXXX.Corp.aepsc.com:389 / 'OU = lob users, dc = corp, dc = aepsc, dc = com' (80072032)
  
  The authentication of the connection Mode and the database Instance Authentication Mode are on LDAP.
  
  Free 8.1.2.0 (B0602) 10.31.2011.0810
  
  Any thoughts!
  
  Published by: user7475518 on April 23, 2012 10:59

  The Internet connection work with baseDN locked in «...» "(Redhat Linux)
  To the customer in option DO NOT work with framed baseDN "..."

  So, the solution was to remove locking them ' ' field baseDN in P6 Authentication Configuration settings.

  ----
  -Duplicate sorry post with my account

  Edited by: 931339 may 1, 2012 11:05

• Debian 5.0 host and Client, network problems

  I have a system Debian 5 (Lenny) as a host for VMware Server 2.0.1 with a configuration ethernet servile (bond0 with Robin balancing).

  This host is the ping requests etc. without problem by any computer in the network and vice versa. This host gets its IP address of a DHCP server and appears very well.

  On this host, I run a virtual client, also Debian 5 (Lenny), with an ethernet in Bridge mode connection.

  This host gets its IP from DHCP Windows without problem and is also listed correct

  The host can ping the client without problems. The client cannot ping the host: ping packets 1 in 10 get through.

  Same story for ping any other computer on the network and vice versa (ping the virtual client from any computer).

  A very small amount of packets through. Can someone help me?

  I'll give you the basic information (see images) for host and virtual client.

  Threesa wrote:

  I changed to mode 5 (transmission of balance) and rebooted, but no progress so far: s

  It was a general indication. If you use a NIC team, no matter whether you use VMware, you use BLT if your switches do not support a protocol group.

  The manual on page 238 describes only for Windows is told by the way.

  .. .and some general tips like this: VMware has not tested and does not support the network adapter teams with

  VMware Server on Linux hosts. »

  Would it because I listed the OS as Debian 4 like Debian 5 was not available in the drop-down list?

  It is a line that wraps a LOT in the newspaper for vmware: cannot find Debian conversion type: vim.vm.GuestOsDescriptor.GuestOsIdentifier

  I do not think because if the problem is related to the link it is not related to the prompt (you can install a Windows client for example who is facing the same problems then).

  I thought back to a NETWORK card to check that your installation works in general. If this is the case, we can try to get the liaison work.

  If you found this information useful, please consider awarding points to 'Correct' or 'Useful' responses Thank you!!

  AWo

  VCP / vEXPERT 2009

  Published by AWo

• Tools, Options problem

  I'm checking my privacy settings by selecting tools, then Options, but nothing happens. How to solve this problem?

  You have this problem when running in Firefox SafeMode?
  
  http://support.Mozilla.com/en-us/KB/safe+mode
  
  Do not choose anything at the moment, just use 'continue in safe mode.

  If this is not the case, see this:
  
  http://support.Mozilla.com/en-us/KB/troubleshooting+extensions+and+theme...

• External DVD drive as first boot option problem!

  Yesterday, I got my Lenovo s10e and as it doesn't have a DVD rom, I bought a DVD burner external Liteon.

  It was installed automatically when I connected via USB. OK, it works very well with windows installed on my netbook.

  However, I can't solve a problem!

  When I chose USB DVD/CD as first boot option in the boot menu (Setup), it does not work! Boot sequence, I changed several times, but all in vain!

  The strange question is when I insert a cool drive with a bootable software, it works very well except for my DVD burner!

  I contacted Lenovo after the sale, they said because my DVD Recorder connects to the netbook through USB, it is not detectable.

  So, what should I do?

  
  

• DHCP client/server problem

  I have no idea how fix this DHCP client/server

  Log name: System
  Source: Microsoft-Windows-Dhcp-Client
  Date: 2010-06-02 17:00:03
  Event ID: 1002
  Task category: no
  Level: error
  Keywords: Classic
  User: n/a
  Computer:
  Description:
  The IP lease 192.*. * *. * for the network card with network address * has been denied by the DHCP server 192.*. * *. * (the DHCP server sent a DHCPNACK message).
  The event XML:
  http://schemas.Microsoft.com/win/2004/08/events/event">
   
     
      1002
      0
      2
      0
      0
      0 x 80000000000000
     
      114138
     
     
      System
      *********-PC
     
   
   
      192.168.1.2
      001E33C2F0C5
      192.168.1.1
   
  

  Hi npgunner,

  1. What is the problem you are having DHCP client\server-related?
  2. What type of internet connection do you use?

  Renew the DHCP client lease

  The IP address of this computer is the same IP address used by another computer on the network. No user action is required. The DHCP client will attempt to get a new IP address from the DHCP server.

  To perform these procedures, you must be a member of theAdministrators group, or must you have been delegated the appropriate authority.

  If you do not want to wait the customer make its automatic renewal attempt, you can manually release and renew the IP address of the client as follows:

  1. on the active DHCP client computer, clickStart, in Search typecmdand press ENTER.

  2 typeipconfig/release, and then press ENTER.

  3. typeipconfig / renew, and then press ENTER.

  Check

  To verify that the conflicts have been resolved:

  1. on the active DHCP client computer, clickStart, in Search typecmdand press ENTER.

  2. to verify a DHCP client lease, typeipconfig/all to view lease-status information.

  3. the output of theipconfig command should show an IPv4 or IPv6 address marked "favorite."

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit ourMicrosoft answers feedback Forum and let us know what you think.

• IPSec site to site VPN cisco VPN client routing problem and

  Hello

  I'm really stuck with the configuration of ipsec site to site vpn (hub to spoke, multiple rays) with cisco vpn remote client access to this vpn.

  The problem is with remote access - cisco vpn client access - I can communicate with hub lan - but I need also communication of all lans speaks of the cisco vpn client.

  There are on the shelves, there is no material used cisco - routers DLINK.

  Someone told me that it is possible to use NAT to translate remote access IP-lan-HUB customers and thus allow communication - but I'm unable to set up and operate.

  Can someone help me please?

  Thank you

  Peter

  RAYS - not cisco devices / another provider

  Cisco 1841 HSEC HUB:

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  ISAKMP crypto key x xx address no.-xauth

  !

  the group x crypto isakmp client configuration

  x key

  pool vpnclientpool

  ACL 190

  include-local-lan

  !

  86400 seconds, duration of life crypto ipsec security association

  Crypto ipsec transform-set esp-3des esp-sha-hmac 1cisco

  !

  Crypto-map dynamic dynmap 10

  Set transform-set 1cisco

  !

  card crypto ETH0 client authentication list userauthen

  card crypto isakmp authorization list groupauthor ETH0

  client configuration address card crypto ETH0 answer

  ETH0 1 ipsec-isakmp crypto map

  set peer x

  Set transform-set 1cisco

  PFS group2 Set

  match address 180

  card ETH0 10-isakmp ipsec crypto dynamic dynmap

  !

  !

  interface FastEthernet0/1

  Description $ES_WAN$

  card crypto ETH0

  !

  IP local pool vpnclientpool 192.168.200.100 192.168.200.150

  !

  !

  overload of IP nat inside source list LOCAL interface FastEthernet0/1

  !

  IP access-list extended LOCAL

  deny ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

  deny ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

  IP 192.168.7.0 allow 0.0.0.255 any

  !

  access-list 180 allow ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

  access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

  !

  How the DLINK has been configured for traffic between the site to site VPN subnets? You are able to add multiple remote subnets on DLINK? If you can, then you must add the pool of Client VPN subnet.

  Alternatively, if you cannot add multiple subnet on DLINK router, you can change the pool of Client VPN 192.168.6.0/24, and on the crypto ACL between the site to site VPN, you must edit the 180 existing ACL

  DE:

  access-list 180 allow ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

  access-list 180 allow ip 192.168.200.0 0.0.0.255 192.168.1.0 0.0.0.255

  TO:

  access-list 180 allow ip 192.168.6.0 0.0.1.255 192.168.1.0 0.0.0.255

  Also change the ACL 190 split tunnel:

  DE:

  access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

  access-list 190 allow ip 192.168.1.0 0.0.0.255 192.168.200.0 0.0.0.255

  TO:

  access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.6.0 0.0.0.255

  access-list 190 allow ip 192.168.1.0 0.0.0.255 192.168.6.0 0.0.0.255

  Finally, replace the remote subnet 192.168.7.0/255.255.255.0 192.168.6.0/255.255.254.0 DLINK.

  Hope that helps.

• 1710 VPN and VPN Client - routing problem '' maybe. ''

  Hello

  I was able to get with 3DES and CISCO VPN Client 3.6.1 1710. with permission of local aaa.

  When I am connected to the VPN I can ping to the IP address of the VPN router

  (24.x.x.x.) and I can ping to the router's internal interface (192.168.x.x).

  The problem is that I can't ping anything else - for example: hosts in the enterprise network (192.168.x.x).

  Configuration:

  The router's internal IP address: 192.168.x.x

  The router's external IP address: 24.x.x.x

  ippool for customers: 10.10.10.x

  The IP address of the Client after the connection is correct: 10.0.0.x (from pool)

  Maybe I'm missing something in 1710 confg? I have NAT interface internal? The default gateway of the net is FreeBSD, not the router of 1710 system.

  All ideas are welcome.

  Miro Pendev

  TI Administrstor

  Quite often, you will lose the first ping because an ARP must be sent and responded to, but if you get the subsequent pings, then it's OK.

  For what is able to browse the Internet while the tunnel is up, you must enable split tunneling. Add the following:

  > access-list 110 permit ip 192.168.1.0 0.0.0.255 192.168.1.0 0.0.0.255

  > isakmp crypto client configuration group my_usergroup

  > acl 110

  This means that the client will only encrypt the traffic to the 192.168.1.0 network, all other traffic shuts down in the clear on the Internet.

• Ensure the mobility Client Certificate Problem | CEP-transfer-url

  Hi all

  I'm having a problem CEP configuration for my secure mobilty client.  I created a connection profile to allow the certificate requests, but when I fill in the url-forwarding-CEP I get an error.

  The certification authority we use is an internal MS CA with PEIE already active.  It has been configured for a long time with our current Cisco VPN client using authentication certificate.  The ASA is running 8.4.1.

  Here is the error I get when I try to enter the command in the associated group policy to my registration certificate connection profile:

  SSLGP group policy attributes

  value of CEP-transfer-url http://10.1.1.2/certsrv/mscep/mscep.dll

  Attempts to retrieve the certificates of AC/AE by using the URL. Please wait...

  Received 3 certificates of AC/AE by using the URL of the CEP.

  NON-RESIDENT CERT: serial: 11111111000100000145, subject: cn = SCEP_ADD_ON, o = OUNIT, c = UK

  NON-RESIDENT CERT: serial: 11111111000100000146, subject: cn = SCEP_ADD_ON, o = OUNIT, c = UK

  NON-RESIDENT CERT: serial: 11111111478AAB288393FAFf2a3E274, subject: cn = CERTSVR-01

  ATTENTION: Please check if you have all the required certificates in the config to authenticate the certificates that will be issued using this URL CEP

  Can someone explain why this happens, because it will not take the config?

  Thanks in advance.

  Ian

  Hi Ian,

  in case you are still having problems with this (I think the question is one week): it seems that the ASA asking you first create a trustpoint (in your case in fact 3 can be required, one for each CA certificate) and import is the CA cert.

  HTH

  Herbert

• X 301 client security problem

  Hello

  My X 301 came with XP installed Vista then I did a clean install of Vista and after I installed the last security client I received the following message:

  http://WWW9.0ZZ0.com/2009/03/31/19/467406581.jpg

  http://www6.0ZZ0.com/2009/03/31/19/213918438.jpg

  Thank you

  Khalifa

  as he says, he must enter the BIOS and disable the TPM chip first. It was like data from the previous Windows user who is not the same as the new windows - probably new user and others.

  When the computer reboots, you can click on the button ThinkVantage or F1 or F2 (I'm not sure) to enter the BIOS. Then find secure TPM option.

• I need some help please (web Vsphere client connection problem with Vcenter)

  Dear professionals

  I can not connect to the server via the customer web vicenter.

  I have installed and configured the following successfully:

  -esxi5.5

  -Win 2008 server1 (installed on AD)

  -Server2 Win 2008 joined to the domain, then I installed on: sso, inventory, customer web Vsphere and vcenter server service

  as you can see in the attached photos, when I double click on the client vsphere of wen I should be able to log on to the server vcenter, but I couldn't do it.

  do not forget that I logged Win 2008 server2 as a domain administrator, then I installed sso, inventory, customer web Vsphere and vcenter server service

  the WebClient service is runningand I tried https://server.example.com:9443 / vsphere client.

  There are more than two things, I noticed:

  -When I turned the web customer service I got the certificate error (see photo).

  -When I typed nslookup in the domain controller I got the error message.  web vsphere client error is related to the DNS error in the domain controller?

  
  

  Please see the pictures attached.

  Please tell me what to do if you have any idea or what is the cause of this problem.

  Please let me know as soon as possible because I've stuck to that point where I can't connect to the via customer web vsphere vcenter.

  Best regards

  
  

  naoufl

  Please register these two servers to the DNS entry field. and make sure both servers firewall set OFF mode.  If the production environment please check the network connection by using the network firewall team.

• P6 Professional client connection problem.

  Hello

  I installed the P6 EPPM 8.3.

  I connect to client tool professional p6 with the user admin/Oracle $123.

  When connecting its showing error like could not link the GPO LDAP: / /:-2147483648 (8007203 A. )

  I double-checked the administration p6-> mode of authentication for LDAP and its native display only data bases.

  I can able to connect to the p6 but p6 client application not able to login with the admin user.

  Please help me to solve this problem as soon as POSSIBLE.

  Concerning

  Kumar

  Hi Kumar,

  I was facing the same problem, it seems to be catching the question. You must remove the capture of ADMIN_CONFIG database table. I used Sqldeveloper connect to the DB using the admconfig user, take backup of the ADMIN_CONFIG table so if you find that remove it all lines with config_name LDAP. Then try to connect through client.

  This trick works for me. I am now able to connect to the business customer of P6 EPPM.

• not getting does not clone/update with VMware Infrastructure client option

  Hi we have an esx3.5 with VIM 2.5

  to authorize the server through a host file, that we had to create a virtual machine on the esx server and install VIM 2.5 above, pointing licensing to the ip address of this server. This vm is winXP so everything works fine.

  When we try to connect to the ip address of the winVista esx server, we get a Manager, without options - clone/updates

  Therefore, in order to make any kind of cloning or updates remotely of machines WinVista you must:

  create a VPN connection on the site with the esx server,

  Connect to the ip address of the esx server,

  Open the VMware Infrastructure client,

  opening of session

  Open the console of the computer that has installed VIM 2.5

  and perform a cloning from inside the virtual Windows XP machine

  as you can see it's pretty heavy. is there another way?

  Thank you!

  Because if I understand your message, you don't see the "Clone/Update" option in the menu when you connect thru customer VI ESX Server. Yes, this isn't. ESX does not provide the functionality without VirtualCenter. Then, must use VirtualCenter, address IP/Hostname in the VI Client to accomplished these tasks.

  Shan

  If you found this information useful, please consider awarding points to 'Correct' or 'useful '. Thank you!!!

• Very weird client connection problem: customer TAF can only access in standby mode

  I have created service and trigger on the principal database and the service started.
  
  However if I test it on my workstation, I can not open into the fermenter at all with the ora-12514 error.
  
  However, if I do a failover to the standby database, at this time there Eve becomes primary, I am able to connect to this service.
  
  Or I tried to start the service on the database pending while the watch is in sleep mode, I can't connect to the service_name even relaxation for the primary database connection.
  
  How to diagnose this problem?
  
  Help, please. Enjoy your time.

  Hello;

  I would check the client side first. I think you probably have a problem minor tnsnames.

  If the listener is not running, you can't get a TNS-12514 - means that you get a listener is running, but it's good?

  Troubleshooting - ORA-12514

  1. Enter the command-line command "lsnrctl status".

  2. check the host for which the listener is listening if it is not correct, the difficulty of the LISTENER. ORA

  3. check (on this host) port on which the listener is listening if it is not correct, the difficulty of the LISTENER. ORA

  4. check if the listener knows of this service

  Client side in the TNSNAMES file. ORA

  1 make sure that the points of entry to the correct host ADDRESS (verification of strike fault).

  2. check the ADDRESS of the entry points to the right port (PORT = 1521) (this would cause this error)

  3. check the ADDRESS of the entry points to a known service (once again a small typo will really hurt)

  If it still does not work, check the SQLNET. ORA make sure that domaine_par_defaut is not incorrect (it is a long shot)

  I guess your trigger start service, begins in the affirmative and lsnrctl shows, to Client-side. Sleep works if the triggers will fire OK it. Recheck the service name vs say what tnsnames. Try to manually start the service outside the trigger and if it still doesn't work its probably isn't the trigger.

  Any chance one of the entries is missing in the tnsnames file? Or has a hidden piece of white space around it for the primary is broken but the work of sleep?

  I would check "The tnsnames.ora used by the customers of the Application" here:

  http://uhesse.WordPress.com/2010/11/05/real-time-query-for-read-mostly-applications/

  Best regards

  mseberg

  Published by: mseberg on December 17, 2011 09:02

• Instant Client connection problem - Excel 2007 for Oracle 10 g

  Dear users,
  
  I want help to connect Excel to Oracle.
  I use Excel 2007 (32-bit) on Windows Vista Enterprise 64-bit. I want to connect to a database 10g to Oracle through our local network using ODBC. I need to retrieve data once in an excel sheet.
  There is no firewall or connection between my current computer problems, problems as I can connect to my machine, using SQL developer as a local client to the Oracle database that is located on another machine on the network.
  I tried to make an ODBC connection, but Oracle is not listed as a driver.
  In my view, what ODBC is the best way to do it, but please correct me if I'm wrong.
  
  It is an Oracle 10 G database.
  I downloaded instantclient-basiclite - 64 - 11.2.0.2.0.zip a windows.x
  I also downloaded the additional ODBC components: * Instant Client Package - ODBC: extra to allow ODBC applications libraries.
  
  I unzipped in a folder called C:\instantclient_11_2
  The system path include one. I checked after reboot.
  I placed my tnsnames.ora (that I copied from the server) in this folder.
  I got it from the server: D:\Oracle\Ora10gR2DB\network\admin\tnsnames.ora
  
  I ran the exe "odbc_install" and he told me that the ODBC has been successfully intalled.
  
  When I went to the Control Panel, administrative tools, ODBC
  
  On the user dsn tab
  
  I added a new entry. I chose the Oracle driver (previously it was not in the list)
  
  Use the following values
  
  Data Source name: OracleL
  123 description
  The TNS Service name: I chose for my prod environment drop-down list. (There are two entrances with the name of the production, one uppercase and one lowercase)
  
  
  UserID: my user name
  
  I tried the connection Test and got this:
  
  Unable to connect
  
  SQlState = S1000
  [Oracle] [ODBC] [Ora] ORA-12545: Connect failed because target host or object does not exist
  
  
  Any suggestions please.
  
  Thnaks in advance.
  
  
  A.
  
  
  
  
  
  
  
  
  
  
  
  Thanks for all your help in advance.
  
  Akajohn.
  
  Published by: user12282521 on May 19, 2011 13:47

  user12282521 wrote:
  I want help to connect Excel to Oracle.

  I use Excel 2007 (32-bit)
  I downloaded instantclient-basiclite - 64 - 11.2.0.2.0.zip a windows.x

  If Excel is 32-bit (2007a) and the Oracle client libraries are 64-bit, it will not work. needs 32-bit 32-bit.
  You should probably remove current ic packages and get the 32-bit instead.
  Start over.

  When I went to the Control Panel, administrative tools, ODBC

  On Windows x 64, to run the 32 - bit ODBC DSN/drivers, we need run the Windows\SysWoW64\odbcad32.exe tool.