Want 5640: Printer won't turn on

Similar Questions

• The HP printer won't turn on or respond when the power button is pressed

  The HP printer won't turn on or respond when the power button is pressed

  The HP printer won't turn on or respond when the power button is pressed

• Printer won't turn on and have error msg 83 00020 Photosmart 6510

  Photosmart HP 6510: Start button / stop does not illuminate, and the window of the printer has an 83 00020 error code. There is a green light uder blinking camera icon near the card readers. Under XP/sp3. Printer is 4 years old.

  Try to remove the cartridges and reset the power to the printer. If the printer has been restarted on the same error code, then it is possible that one of the parties in the printer did not. If the printer asked for cartridges to install then one of the cartridges is a failure or the printhead system itself is a failure.

• Bridge of Sony for Mac. wanted an update, and phone won't turn on now!

  Hello

  Today, I tried to transfer files from my phone to my Mac. When I plugged my phone the Sony Bridge for Mac asked me if I'd like to update so I clicked Yes and it started to be updated with my phone connected. Then out of it, my phone off and it won't turn on. It will only vibrate and display the Sony logo but won't go any futher. I tried the combination of flight + and start/stop button and many others, but nothing works! I need my phone very quickly at work, and I really don't want to lose all the files!

  Help, please!

  It sounds more like you had an update to the system firmware and you can have disconnected your phone that this process was going on - anything you can do I'm afraid to say is a repair of the system, but this will erase all data on your phone

• HP ENVY 5644 e-all-in-one Prin: I want to print in black and white

  Hello

  I wanted to print in black and white but still my printer print in color when there is a picture in the paper, it's really annoying because when I go to the properties of the printer I press black and white or black press ink only then when I press on save, I'll be back in the printer properties to find her back to color No matter how many times I put it in black and white it goes back to color. I tried pressing black and white and not return to the printer properties, but it still prints in color. Also, I changed my default settings of the printer in black and white through the control panel and tap Save. When I go into Control Panel, its saved printer properties such as black and white by default, so that's good. But for some reason when theres color of text or an image on the page I want to print, I can not change to print in black and white, keeps coming back to color.

  Please help me!

  Hello @Matthew002, hope you are well!

  Thank you for joining the HP support forums, I would like to help

  I understand that you are having problems when printing in black and white and also the printer goes "offline".

  Going through your post, this could be a problem with the printer drivers. In this case, we might need to uninstall the drivers and re - install the same.

  • If present, disconnect the USB cable between the printer and the computer.
  • Go to control panel of configuration-programs and feature - select the HP Envy printer entries and uninstall them.
  • Restart your computer.
  • Now, click http://ftp.hp.com/pub/softlib/software13/printers/en5640/Basic_Webpack_x64-40.2.1073-EN5640_Basicx64_Webpack.exe and install the printer drivers.
  • If you are prompted, connect the USB cable.

  Now try to change the printing preferences:

  • Go to control panel - devices and printers - give Envy 5640 right-click and select Printing Preferences.
  • In the pop-up window, click on the 'Advanced' button - check for printing in grayscale option. Make sure it is turned on

  PS: Your printer support mode single cartridge. So if you want to completely stop color printing you can get out the color cartridge and use only black.

  Let me know if this helps. Good luck!

  See you soon

  Please click on 'acceptable' on the post that solves your problem to help others to find the solution. To show gratitude for my help, please click the 'Thumbs Up icon' below!

• iMac won't turn. Startup disk is full. TDM won't let me edit.

  iMac won't turn. Startup disk is full. TDM won't let me edit.

  My iMac turns off 10 seconds after the start to the top. I tried repair disk running, to no avail. What is happening is because my boot drive is full, off the 500 GB I partitioned in mac, 493,63 GB is taken up. I bought a thunderbolt cable to access the TOC on my mac book, and I have access to my files now. The problem is that I can only copy files. Authorities say I read and write permissions. When I start my host computer, it says "you can still open or copy the files on the disk, but you cannot save changes to the files on the disc. Back up the disk and reformat it as soon as you can. "I'm trying to copy all my files on this computer and remove what I don't want copies, then reinstall OSX on my iMac. The problem is that some files are native to all OSX, so it would prevent me from copying the files. For example, if I want to copy my applications folder, it stops to copy once it reached the app store, because it cannot copy that. It is a problem because when it comes to the library, there are small files in there that I don't know if I can copy, then it stops at the copy and I end up with half of my files and I don't know what I need and what I have.

  Everything you need to copy the disk, then start the iMac in recovery (command-R) mode. Wipe the drive and reinstall OS X from the recovery console.

• iPod 5th generation won't turn on after falling in the bathroom and then dry with rice! What should I do?

  Hello

  My iPod touch 5th generation won't turn after being immersed in water bath for about 15 seconds and then dried to rice. I tried pressing both the House and the buttons but nothing happens! My iPod is about a year and a half and it usually works very well.

  It really scares me because it's the only small portable device I have, which means that if I lose, I'm stuck carrying my iPad autour, which is quite heavy. Also, I wrote something about the iPod that I really like, but I didn't sync it to my computer, as I was traveling while I wrote it and then also when the machine broke.

  This is an urgent matter, because I travel by plane in twelve days and there's a pretty long flight. I want it fixed right here - what can I do?

  Thank you

  Stella

  Hello moxie.star,

  Thanks for this info and choosing the communities Support from Apple. I know how important to get your iPod working again is for you! Based on what you said, it seems you can be affected by a hardware problem and get your iPod repaired by a technician to repair Apple. Please click on this link to find the best option for your situation:

  the Service response to iPod

  See you soon!

• MY PRINTER WON'T STOP PRINTING

  I have a brand new HP 309 a wireless printer.  I use it with a USB PORT.   I downloaded something from a PDF file and the printer won't stop printing.  I rebooted the computer, I unplugged the printer for an hour and when I turned it on it took I hit the Cancel button, the display shows "Printing cancelled", then it reads 'print now.'  When I try to use the printer to print something it reads "busy".  Help.

  Hello

  Unplug the USB cable and follow the steps below to restart the spooler service.

  Click Start (Windows logo) > > all programs > > Accessories > >

  Right-click on command prompt and open it as administrator (choose Run as administrator)

  Enter the below command in the black window and click on enter key...

  net stop spooler

  Who will stop the spooler service.

  Then enter the command below and hit enter key to start the spooler service

  net start spooler

  That will remove the current impression comment and things in the print queue.

  Press the Windows key and R on the key board to open the run window (click Start > > run).
  
  In the run window, type services.msc, and then click Ok.
  
  Which will open the services window.
  
  From there, double click on the print spooler service. Which opens a new window.
  
  Click the Stop button to stop, and then click Start to restart the spooler service.
  
  Make sure that the startup type is: automatic status and Service: started
  
  Click apply and then click Ok to close the services window.

• printer does not turn on

  My Deskjet 6980 printer has stopped working.  It has worked very well so far. Flashing lights said he needs ink. I put in the new ink. Now, it won't turn. The power supply is turned on, the works of output (without surge protector), but the printer does not turn on. In all he has no light on the printer, except light power cord in the back. I tried everything I could find online, but nothing works. My computer was still recording the printer, but since it will not power, says that it is in offline mode. Any suggestions would be helpful.

  The unit may have developed a power failure, but may be also simply in a State of error because of the fresh cartridges.  There are a few steps, I'll try in this case of troubleshooting.

  * If possible, try to remove the cartridges that you recently installed before performing a hard reset of the printer.

  * Hard reset of the printer by unplugging the device, disconnect the other end of the power cord from the wall outlet, separates the power cord of the power supply, wait 30 seconds and plug it back up.

  See also the steps described in the document, found here, to solve a lack of power.  I hope this helps.

• IdeaPad 300 won't turn on (new)

  Hi, I bought a Lenovo Ideapad 300 - 15isk this weekend and he needed for work this week, but it's really frustrating, it's brand new, out of the box and it won't turn. I hear sounds and I can see the lights, so I know that the system works, but I'm stuck with a black screen. I wanted to make a "difficult start" but I can't even find the battery. Very disappointed so far...

  It seems that it is a fairly common problem from what I see in many forums. Since I don't have any answers on this community, I am a refund in store and probably buy another model from another brand.

• I get an error message when I want to print from my laptop on my Lexmart printer wireless. It is said "problems connecting to the printer.

  original title: devmgmt msc

  I get an error message when I want to print from my laptop on my Lexmart printer wireless. It says "connection to the printer problems" sometimes he just complained and then prints, sometimes it won't print at all. I hate the thing!

  Hello

  I suggest you to see link below and check if it helps.

  http://www.Lexmark.fr/publications/pdfs/810/winug/Eng/UGnetwk.html

  I suggest also you see the steps from the article below and check if it helps.

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-printer-problems

• "HP OFficejet Pro L7680 turns off and won't turn back on"

  HP OFficejet Pro L7680 turns off and won't turn back on.

  Hello untech,.

  I see it's been a while since you have posted with us on the HP Forums.  Please, let me take a moment to say "Welcome Back".

  I see that you have a problem with the printer l ' auto turn off and not turning it back on.

  You happen to have the printer power cable connected to a power strip/bar?  If so, please try to connect the printers power cable directly to a wall outlet.  Here is a document that explains the problems when connected to an uninterruptible power supply/Strip/surge protector power.

  The printer in the document is a LaserJet printer but this document is intended for HP products in general and only use the LaserJet printers for example.

  I'll also include a document indicating when the HP printer will not be running or to respond when the power button is pressed.

  If by chance the problem is not resolved after you complete the steps described, then I would say call the HP Technical Support to see all the other possibilities for you. If you call in North America, the number is 1-800-474-6836 and for all other regions, please click here: click here.

  Please do not hesitate to write me again if you have any other questions.

  I wish you a great Monday!

  See you soon,.

• all in a single j6480 won't turn on or off by pressing the power button

  my all in one j6480 won't turn on or off by pressing the power button. from pluging in the power cable to the output, the display panel stays on by a flashing point moving from left to right, repeatedly. also, there is a faded beeps coming from the printer on the left side. See no empty self am unable to do anything on this subject.

  There may be a problem with the power supply/power cord module brick.  Try following the steps described in this document.  If that does not receive the printer works properly again, you can try to contact tech support to buy a new power module (if still available), or you need to replace the printer.  You can join the 1-800-474-6836 technical support to the United States and the Canada International users click here.  Let me know what happens.

• PCL5 printing codes to turn off paper tray switching when the tray is in the paper

  We have a HP P4015n with 3 trays, tray we letterhead, tray 2 has plain paper, tray 3 preprinted forms (all dimensions 8.5 "x 11" paper ").  This is related to a Linux system with printing from a legacy software - they are mainly text documents that have integrated the PCL control codes.

  The problem, when a drawer is empty, print will continue to the next state bar, which can have a header of letter or preprinted form, etc.

  Can I turn off automatic tray switching?  Either using a code printer PCL or via the printer control panel?

  If I print on tray 3, this tray is empty, I want the printer to wait until the tray has paper once again and do not use a different tray.

  I played a bit with the 'document type' (letterhead, pre-printed form, etc.) setting found on the built-in printer web page, but when I send a job there, the printer needs someone to hit the 'OK' on the printer. I guess that the printer is looking for the paper incorporated in the corresponding document type.  Is there a print PCL code for that?

  I have done research on PCL5 printer control codes and can not find, or another command.

  Thanks for any help,

  This should help you:

  http://h20000.www2.HP.com/bizsupport/TechSupport/document.jsp?lang=en&cc=us&ObjectID=bpl05272&JumpID=reg_R1002_USEN

  On the other hand moving up to the next plateau, depends on the printer.  Some let not work continue to the next bar if the paper type is defined differently, but it is more common that the printer will just continue.  The only solution I have found is when big jobs you know will exceed capacity of the tray should just make sure that the right paper is in all stores.  The other thing is too, to keep the full trays (just make sure to put the fresh paper under the paper that is in the status bar to reduce interference issues).

  I am including the link to the history of PCL/PJL because inside under the additional Documentation, it links to PDFs of the technical manuals detailing everything that you could ever want to know about hand coding for printing using these languages:

  http://h20000.www2.HP.com/bizsupport/TechSupport/document.jsp?objectID=bpl04568

• You want to print the contents of the textfield.

  I want to print the content of the text field with a button. I know how to print a clip. If I turn the text field in a clip, I can't type anything in it, and then I need to print an empty textfield... Help, tip? Thank you.

  There should be no problem converting your textfield to a movieclip and then by typing in it.  you do not really change it to a movieclip, you just add it to the timeline of the movieclip.

  but your textfield must already be in a displayobjectcontainer and so can be added to your printjob.  for example, if your textfield (for example, tf) is on the timeline in the scope, you can use:

  var pj:PrintJob = new PrintJob();

  b.addEventListener (MouseEvent.CLICK, f);

  function f(e:MouseEvent):void {}

  If (pj.start ()) {}

  try {}

  pj.addPage (this, Rectangle (tf.x tf.y tf.width, tf.height)) of new;

  } catch (error) {}

  handle the error

  }

  PJ. Send();

  }

  }