Want 5660: ePrint does not

Similar Questions

• ePrint does not print web pages of Tablet Windows 8 Microsoft Surface

  ePrint does not print web pages of Windows 8 (x 64) Microsoft Surface Tablet

  Any ideas?

  Hello JereTanner,

  Welcome to the Forums of HP Support!

  I see you are trying to print web pages of a tablet of Surface. What model printer you are trying to print to? Also, is there an error, message, etc., when you try to print?

  In general, ePrint is used when printing emails or transmission of documents / photos to the printer address, is the next how you try to print a web page?

  Since it is a Windows 8 operating system, you can be able to install the full features software and print that way. When I know more about how you want to print, what happens when you try and which printer you are using, I will be able to help.

  See you soon,.

• M176n: M176n of MFP LaserJet Pro ePrint does not work

  I have problem with my printer. I can't connect it to the ePrint service.

  EPrint functions is turning on and off without my knowlegde.

  After you have enabled ePrint in the web interface of the printer, printer does not print information sheet.

  When I enter the code for example my last code (from email [email protected]) edy638epu59 in HP connected it says either invalid code or something to the exception.

  I have updated the firmware of the printer.

  I added printer DMZ on my router.

  I changed the router to another.

  I unlocked the ports

  UDP: 5353, 547, 53, 67, 5355, 137, 138, 139 427, 161, 514, 3702, 5357, 445, 3910

  TCP: 445, 68, 80, 8080, 443, 137, 138, 139, 427, 9100, 445, 515, 161-9101, 9102, 9103, 9110, 9220, 9290, 9280, 9500

  UDP port range: 9999 to 65535

  I tried to disable IPv6 in the printer.

  I tried to print the fact sheet on the front panel.

  I tried all possible methods found on the web, and even got my replaced printer - same question...

  Hello @ Averus89,

  Welcome to the HP forum.

  I understand that you did a lot to solve your M176n and its connection to the ePrint service.

  I want to help you with this question.

  If the printer does not print the document to Web-based information services, or allowing you to add to HP connected, I have

  Set a manual DNS.

  I won't go into the details on setting this up. From your post, I think you know your way around the printer and your network. If I'm wrong, let me know. I'll go into the details.

  The DNS to try is:

  Primary: 209.244.0.3
  Secondary: 209.244.0.4

  Set the DNS, and then try again to print the web services information page.

  Let me know if it helps.

• ePrint does not-C310a

  Yesterday bought a C310a, everthing seemed to work perfectly (print apps included) outside of the ePrint, use the update software option the firmware update (which reset the e-mail ID) but still no ePrint.

  The problem is that, although Web Services if poster to assign an ID e-mail the printer does not print the instruction sheet. I also tried to register email to ePrintCenter identification but the email is not recognized - probably because I have not finished the configuration of the printer using the instructions sheet.

  Have also tried disabling Web Services and reactivation. This has not fixed the problem but for a time also thrown upward and the error on the re-login to web services.

  Sent by e-mail to the e-mail address on the printer to confirm and as expected no. print. The stupid thing is I get a confirmation of the eprintCenter when there are in fact that the printer is not fully configured.

  HP ePrintCenter could really do with a service status page - there are clearly a number of problems at the present time.

  Yes, reset Web Services and all now work and in sync.

• HP Deskjet Ink Advantage 4645: ePrint does not work

  I bought HP Deskjet Ink Advantage 4645. Start ePrint feature is impossible.

  I do the following:

  (1) press (ePrint) buttons at the front.

  ((2) I get a failure... as ' proxy or Internet to check connection settings).

  (3) given that I see the work perfect Internet connection, but on the settings, I found that there is no value of proxy and the port is 0.

  I live in Greece (maybe the functionality is supported by my country?)

  Thank you

  Hello

  I hope that you were trying to save the printer directly from the front of the printers, this is an additional method to enable the web service.

  Once you connect your printer with the cable network, let the printer get the IP address.

  Now plug your laptop or your PC in the same network.

  Type the IP address of your printer in the address bar of the browser and hit enter.

  Now, you will see the embedded Web Services Page.

  Access the Web Service tab and click Activate or click the eprint on the façade of the printers and proceed with the registration process.

  Now, the printer must be turned on and print a sheet with the claim code.

  NOTE: If you don't see the Embedded web services page, try unplugging all other devices out of the laptop and printer, then restart the wifi, the printer should pick up the IP address and connect to the internet.

  Your Internet service provider must be able to provide the settings of proxy for your network if its still does not.

  Kind regards

  Oliver

• WANT TO 4500 DOES NOT PRINT ALL OF THE GRID

  WANT TO 4500 ALL IN ONE PRNTER DOES NOT PRINT ALL OF THE GRID

  My problem seems to have resolved itself.

  Thanks for responding.

• Want to 4500: HELP! Want to 4500 does not print long documents

  Would be really grateful for help at the time want to throw printer out the window!

  We brought this printer a few weeks ago, and despite the installation and uninstallation of several times, it still does not work properly. I tried printing HP and Scan doctor as well but who comes up with there is no problem. When I try to print a document with more than 4 pages it starts fine then stops mid page and it comes up with an error on the computer saying that it was impossible to print!

  Any ideas?

  Thank you

  Claire

  Clear, Microsoft has released a patch to resolve a conflict with the network WSD Port in the Windows 8.1.

  Please click here to download and run a Microsoft Fix it Tool.

  Once the site opens for the fix, please click the button for "hotfix download available".

  Once you have installed the patch file restart your computer & try to print.

• Want dv6 wifi does not

  Product name: HP ENVY dv6t-7300

  Operating system: Windows 8

  WiFi no longer works. I restarted and shut down the computer several times but it still does not work. It was fine until last night. I did all the changes to the laptop before it happens. But I dropped my computer on the floor, about 2 weeks ago. Last night the connection was pretty slow, so I turned on airplane mode, but the light didn't turn orange. Turn off the airplane mode and I couldn't find any network to connect at all. I rebooted my computer, wifi still doesn't work do not. Finally, I decided to give the laptop a rest and stop for the night. But this morning, wifi still doesn't work do not.  What should I do to solve the problem?

  Hello

  I couldn't find wifi but I find network adapters. But I troubleshoot for information contained in what's wrong with the computer and wifi is now WORKING once AGAIN! Thanks for trying to help.

• Want 5530: Printer does not print in black ink

  I recently updated my HP 8.1 Windows of Windows 10 laptop.  I have the same type of printer (Envy 5530) installed at my other House and updated my desktop computer for Windows 10 and had no problem with printing, but now I'm with the laptop.  I try to print documents now and the printer does not print anything using black ink.  Color ink prints, black ink just not. The two jets of ink are filled.  I did all the "try these patches" suggested Windows and HP Print doctor.  I uninstalled and reinstalled the printer twice.  I rebooted the computer several times.  I'm no tech person by any means and have no one to help me or ask what else to do. Can someone help me understand this please?  Thank you!

  Hi @KKLfromIA,

  Welcome to the HP Forums!

  I understand that you can not print in black with your printer to HP Envy 5530 on Windows 10. And I'm happy to help you!

  You use genuine HP cartridges or refills?

  One of your ink cartridges, low or empty?

  In the meantime, try the following solutions:

  Solution: remove the black print cartridge

• What should I do if the eprint does not accept my printer code?

  ePrint will not accept the code for my printer.  Could someone have used by chance?

  I figured out how to reset the configuration of Web services using "Restore factory settings" on my HP OfficeJet 7500 E910.

• ASUS MeMo pad 302 c impossible eprint. "Eprint does not.

  I have a new Asus 302 c Tablet and I downloaded the eprint application, but when I "share' the application to print something I get a message that says"eprint has stopped working"I can only print if I"share"to email and then send anything, I want to print to the printer email address. I have no problem with direct printing from my ipad or my Android phone without having to go through email first. I'm doing something wrong or is there a problem with compatibility between the Asus Tablet and my HP eprint printer?
  Thank you

  Hi Bentley12,

  Thank you for the additional information.  I really appreciate it.

  Please implement the ePrint on your printer.  You start by getting the printer application Code.  Once the fact sheet of web services with the code of your application, please follow the instructions in setting upward a Custom Email Address for ePrint.

  Please add the printer to your HP ePrint app by email of the ePrint printer address. The steps on how to do this are in the HP ePrint Mobile App FAQ document, under the question "How can I add a printer on my mobile device?   This should stop the error message you see.

  For additional reference, I've also included the Android 4.3 (Jelly Bean) and earlier versions: printing with printing from Android Solution document.

• ePrint does not print the deskjet 3050 a spare

  I have deskjet 3050 a and unable to print attachments. text is ok but no pdf, excel, photos etc after research I know that the pdf files is not oversized.help please

  Hi there, if you try to print from a laptop to the printer you need not send attachments e-mail to the e-mail address of printers, you can simply print via regular HP printer software driver. DJ 3050 has installed on the laptop? If not, here is a link to where you can download Windows 8 driver for your system, simply select the correct option (32 or 64 bit) for your operating system http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?cc=us&dlc=en&lc=en&product=5061092&

  If you want to be able to print from the laptop to the printer when the devices are not on the same network or if you do not want to install the product software, you have the option to install the software driver ePrint. This will allow you to print files from applications on your laptop (Adobe, MS Office, etc.) to your printer ePrint enabled even when they are on different networks. See this link for more information and a download link

  http://h20331.www2.HP.com/hpsub/us/en/eprint/overview.html

  Hope this information helps.

  Best

• EPrint does not print the spare part on Photosmart 6510 using MACBook ro

  When I send an email with attachments to my Photosmart 6510, it prints the email but not attachments

  What type of attachment you send?

  The file types are limited to Microsoft Office (some of them), image files (jpg, gif, tiff, and a couple more) and HTML formatted emails condition are not any dynamic material in them.  File size is limited to 5 MB for e-mail + attachment

  What does say in your ePrint centre?

• WANT to 114 does not connect to the Web server

  Have installed a 114 WANT, everything works except for the webservices - wireless eprint etc.

  I tried everything-

  1 re-install services - error cannot connect to the web server

  2. Update - error cannot connect to the web server

  3 give the static IP address

  4 restore the default settings

  I have an internet connection on all computers.  Can someone give me a hint on how to get Web services to work?

  Hi sbenzie,

  How your printer is currently connected to the network? Via Ethernet or wireless? What is your current router / network configuration? That shows your printer because it is the IP address? What happens when you try to launch applications?

  Not yet given the information above, here's what I would try.

  I suggest to reconnect the printer to the network by running the Wireless Setup Wizard and attempt to restart the web services. If this is not enough, you may change some DNS settings in printers EWS (built-in web server) to do this, put the IP address in a browser window on your PC.

  This should start the integrated Web server. In SAP, select the network on the network tab, select 'network '.

  Then select "network address" (IP). Do not change the IP configuration at the top. Go down under "DNS address configuration"and select 'Manual DNS server'. " Under manual DNS server, enter (an 8 in each box on the first line) 8.8.8.8 and 8.8.4.4 on the second line. Press the button 'Apply' at the bottom.

  Now try to connect to Web Services again.

• ePrint does not-Deskjet 3070

  I'm having a lot of trouble to do my printer doesn't work on the side things eprint.

  The IP address is the same on my router/printer/HP eprint website, so I don't know what's wrong.

  My printer is back with "the printer could not connect to the internet. Check the Internet connection.

  The wireless aspect works very well.

  Ubuntu 11.10/HP Deskjet 3070/Virgin Supehub

  Kubuntu 14.04LTS / Photosmart D5460 / 3070 Deskjet / Officejet 4630 / LibreOffice Version: 4.2.7.2 Build ID: 420 m 0 (Build:2) / Netgear WNR2200 / Virgin Media SuperHub 2

  Hi pooky2483,
  
  (On your printer) Reconnect the printer to the network by running the Wireless Setup Wizard and try to restart the web services. If this is not enough, you may need to change some settings of DNS in the EWS (built-in web server) printers
  * To do this, put the IP address in a browser window on your PC.
  
  This should start the integrated Web server. In SAP, select the network on the network tab, select 'network '.
  
  Then select "network address" (IP). Do not change the IP configuration at the top. Go down under "DNS address configuration"and select 'Manual DNS server'. " Under manual DNS server, enter (an 8 in each box on the first line) 8.8.8.8 and 8.8.4.4 on the second line. Press the button 'Apply' at the bottom.
  
  Now try to connect to Web Services again.