What is a connection to the network tunnel adapter local?

Similar Questions

• Computer connects to the network wireless as "local only".

  I am running Vista Home Premium SP2 on a HP Pavilion laptop.  I've never had any problems to connect this machine to a wireless network before, in hotels, at home, or anywhere.  My current home network is a modem - cable-> wireless-> wireless netgear n300 router.  My laptop connects to the internet via the modem cable directly or a wire from the netgear router.  I have a second, almost cell identical (it's intel, while the one who does not is AMD) which connects to the network wireless without any problem.  Two iphones connected wirelessely without any problem.  My HP laptop is the only one who refuses to connect to the internet.  Connected to the wireless network, it has access "local only".

  I tried the solution in this article: http://support.microsoft.com/kb/928233

  The question does not seem to receive an ip address, the computer receives an ip address.  I have disabled the IP v6, ran the norton removal tool, because I only had to a point and tried all other suggestions in these discussions: http://social.answers.microsoft.com/Forums/en-US/vistanetworking/thread/0949042d-074e-43ab-ba95-3c06cc2aa6be and http://social.answers.microsoft.com/Forums/en-US/vistanetworking/thread/bc08f0e7-49a9-4458-9e0e-149b2df362ec.  I've uninstalled and reinstalled the adapter and all TCP/IP and network protocols associated with it.  I am at a loss and would welcome any ideas.

  Here is the result of the command ipconfig / all:

  Windows IP configuration

  Name of the host...: Arrakis

  Primary Dns suffix...:

  Node... type: broadcast

  Active... IP routing: No.

  Active... proxy WINS: No.

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :

  ... Description: Atheros AR5007 802. 11 b / g WiFi adapt

  Physical address.... : 00-1E-4C-B2-32-BC

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  IPv4 address: 192.168.1.5 (Preferred)

  ... Subnet mask: 255.255.255.0.

  Lease obtained...: Wednesday, 28 April 2010 21:40:55

  End of the lease...: Thursday, April 29, 2010 21:40:55

  ... Default gateway. : 192.168.1.1.

  DHCP server...: 192.168.1.1.

  DNS servers...: 192.168.1.1.

  NetBIOS over TCP/IP...: enabled

  Ethernet connection to the Local network card:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: NVIDIA nForce Networking Controller

  Physical address.... : 00-1B-24-FA-DA-80

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 10:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: isatap. {31C080CE-FE0B-4D50-B734-C782C9A25FBC}

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 6:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: isatap. {B198B0D3-B70A-4E3E-858D-9774C414EECD}

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 14:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Teredo Tunneling Pseudo-Interface

  Physical address.... : 02-00-54-55-4E-01

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 11:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Card 6TO4

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  If anyone has this problem, it has been resolved by rolling the security settings on the router WEP.  I got the answer from the support client netgear.

  Amazing how two iphones, another laptop with XP and a laptop running Ubuntu Linux all about them without any problem, but wouldn't connect Vista laptop.

• Computer Windows Vista says it is connected to the network 4. I don't know what is network 4.

  on the bottem of my screen where the icons were similar to the he mcfee icon and symbol of volume there is a picture of 2 small computer screens, and when I scroll above him, it says connected to the network 4. I don't know what network 4 is and I have never seen this before and the other day I saw him and it says connected to network 2. I would like to know if anyone can help me in this matter. What network average 4?

  original title: bottem icon

  This icon is the icon of your network. You don't say what kind of network you are using. However, I will give you an example. If you repeat your network connection or use a network USB key and plug the key to another USB socket and create a new Windows login will name each new connection 4 then 2 then 3 and so on. You can rename the connection to your liking. To rename the link to right click on the network icon in the notification bar, click Network and sharing Center, click on manage network connections, right-click your network connection icon and click Rename.

• Can connect to the network, but not the internet, a "Local" access only

  Just installed a new router and am now unable to connect to internet on my HP laptop. The laptop is running Windows Vista 64-bit Service pack 1. Pulling him diagnose & repair window returns a message indicating "your modem or router is not available.

  I tried several things to get the internet to connect. I have reinstalled the driver, turned off the firewall, disabled the Internet Version 6 (TCP/IPv6) Protocol and manually configure the network connection.

  I have a desktop computer with a wireless adapater that performs the exact same OS as the laptop and I have no problem with this connection.

  I am able to connect to the internet if I connect the laptop to the ethernet cable. I am completely confused and would appreciate any advice!

  Hi Ima be,

  You can follow the steps below and check if that helps you solve the problem.

  Method 1

  Try to power cycle the router and the computer and check if it helps.

  On the PC:

  1. Save your work and restart the machine.

  On the router or modem (if wireless printing):

  1. Unplug the router and the modem.
  2. Wait 30 seconds.
  3. Plug in the modem and wait for it to come to the ready state.
  4. Plug in the router.

  After you put cycle check the connection between the router and the computer.

  Method 2

  If the steps above do not help, you mayreset TCP/IP stack. To reset access the link below and either click on "Fix it for me" or follow the instructions to fix it yourself:http://support.microsoft.com/kb/299357
   
  Disable the IP helpdesk:
  1 hold the Windows key and type R, type "services.msc" (without the quotes) and press enter
  2. scroll down to the IP assistance service, right-click on it and select Properties
  3. in the drop-down list box that says "Automatic" or "Manual", set it to disabled and then click 'apply '.
  4. then click on "Stop" to stop the service from running in the current session
  5. click on OK to exit the dialog box

  Method 3

  Disable IPv6 and remove IPv6 virtual cards:
   
  Try to uninstall IPv6 on all interfaces, the removal of virtual cards of IPv6 and reset the TCP/IP stack. To remove the IPv6, go to the properties for each network adapter, and deselect the check box next to the Protocol "Internet Protocol version 6 (TCP/IPv6), which will turn off, or select it and click on uninstall, which withdraw power off the computer.» Then go into Device Manager and remove any 4to6 adapters, adapters miniport WUN or tunnel adapters.
  NOTE: You should do this for each network connection, even if they are disabled.

  Method 4

  Disable the DHCP Broadcast Flag:
  Link: http://support.microsoft.com/default.aspx/kb/928233
  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  http://support.microsoft.com/kb/322756.  How to back up and restore the registry in Windows
   
  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
   
  To resolve this issue, disable the DHCP BROADCAST flag in Windows Vista. To do this, follow these steps:
  1. Click Start, type regedit in the search box, and then click regedit in the list programs.
  2. If you are prompted for an administrator password or for confirmation, type your password, or click on continue.
  3. Locate and then click the following registry subkey:
  4 HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\ {GUID}
  5. in this registry path, click the (GUID) subkey that corresponds to the network adapter that is connected to the network.
  6. on the Edit menu, point to new, and then click DWORD (32-bit) value.
  7. in the new area #1, type DhcpConnEnableBcastFlagToggle and press ENTER.
  8. right click on DhcpConnEnableBcastFlagToggle, then click on modify.
  9. in the value data box, type 1 and then click OK.
  10. close the registry editor.
   
  By setting this registry key to 1, Windows Vista's trying to get an IP address using the BROADCAST flag in DHCP Discover packets. If that fails, he will try to obtain an IP address without using the BROADCAST flag in DHCP Discover packets.
  You can also try uninstalling and reinstalling the driver for the wireless card.

  I hope this helps. Let us know the results.

  Thank you and best regards,

   

  Srinivas R

  Microsoft technical support.

  Visit ourMicrosoft answers feedback Forum and let us know what you think.

• My UK 6s iPhone does not connect to the network in Germany?

  My UK 6s iPhone does not connect to the network in Germany?

  'The network '? Which network? WiFi or cell phone? And what have you already tried to get connected?

• OfficeJet Pro 6830 hangs when it is connected to the network

  I just pick up a Pro OfficeJet 6830. I installed the ink cartridges and it seems to be able to print copies and test pages, but I can't seem to connect to my network. Here is what I tried:

  Using the Wireless Setup Wizard

  I selected my network in the list and entered my WPA key. It says it tries to connect, then the following occurs:

  1 briefly press (for less than one second), a screen will appear showing that it has successfully connected to the network.

  2. Press briefly (for less than a second) the screen flashes blue with an icon of 'power' and 'B8B2A4F8' text (which I assume is an error code).

  3. the screen display changes to "printer error: there is a problem with the printer.» "Turn the printer off, then on.

  4. after restarting the printer, he complains that he has not been arrested properly.

  Any other attempt to connect gives the same results.

  Ethernet connection

  If I turn on the printer when connected via Ethernet cable to my network, after about 10 seconds it crashes as described above (steps 2 and 3) without doing me anything at all.

  I also tried a "Hard Reset" (i.e. unplug the printer for 60 seconds, and then it turning it back on again). This made no difference whatsoever.

  I managed to get it to connect to a WiFi hotspot on my laptop (and I checked the firmware updates, but unfortunately there is none available), it seems that there is something of my network that do not have the printer. I have no idea what this could be, however. Someone at - it ideas?

  It solved!

  I spent a bit of time on the phone with HP tech support and the guy could not actually solve the problem for me but it helped prove that the hardware network printer works OK. I could connect the printer directly to my PC via Ethernet, then ping and access the built-in web server.

  It occurred to me that perhaps the problem was related to DHCP, because the printer broke immediately after the connection to the network. My router is an Asus RT-N66u with custom firmware (version Asuswrt-Merlin 376.48_3) and I could see the router newspaper that he was sending a DHCP acknowledgement to the printer just before he died.

  So, here is what I did to solve the problem:

  1 turn off the DHCP server on the router.

  2. on the printer, operated the network icon on the homescreen (at the Middle bottom) wireless.

  3 typed down "gear" icon to the left (settings).

  4 typed "wireless settings".

  5 typed "Assistant wireless configuration".

  6 selected my wireless network and entered the WPA key. This time, no crash, but he did not get an IP address assigned (obviously).

  7. back in 'Wireless Settings', I typed in 'advanced settings '.

  8 typed 'IP Settings'.

  9. tapped "manual (static).

  10. enter in the details for my network - yours will probably be different, but I entered in what follows:

  IP address: 192.168.002.201 (I chose this because it is outside the range of addresses, the router for DHCP problems).

  Subnet mask: 255.255.255.0

  Default gateway: 192.168.002.001

  DNS address: 192.168.002.001

  11 hit 'apply '.

  12 re-enabled the DHCP server on my router.

  And now it works!

• Unable to connect to the network and network adapter is not detected

  Hello, this is the first time I use a laptop ( HP Pavilion 2332se g6 ) and I installed Windows 7 Ultimate 64 bit. I cannot connect to the network (wired or wireless) and cannot connect to Wi - Fi.

  My problem is perhaps the same problem in this post in your forum, so I provide the same information. If it's not the same problem, ask the details you need.

  What I see in device (with hardware ID) Manager:

  • Other features:

  Bluetooth controller:

  PCI\VEN_1814 & DEV_3298 & SUBSYS_18EC103C & REV_00

  PCI\VEN_1814 & DEV_3298 & SUBSYS_18EC103C

  PCI\VEN_1814 & DEV_3298 & CC_0D1100

  PCI\VEN_1814 & DEV_3298 & CC_0D11

  Ethernet controller:

  PCI\VEN_10EC & DEV_8136 & SUBSYS_183E103C & REV_O5

  PCI\VEN_10EC & DEV_8136 & SUBSYS_183E103C

  PCI\VEN_10EC & DEV_8136 & CC_020000

  PCI\VEN_10EC & DEV_8136 & CC_0200

  Network controller:

  PCI\VEN_1814 & DEV_3290 & SUBSYS_18EC103C & REV_00

  PCI\VEN_1814 & DEV_3290 & SUBSYS_18EC103C

  PCI\VEN_1814 & DEV_3290 & CC_028000

  PCI\VEN_1814 & DEV_3290 & CC_0280

  PCI device:

  PCI\VEN_10EC & DEV_5229 & SUBSYS_183E103C & REV_01

  PCI\VEN_10EC & DEV_5229 & SUBSYS_183E103C

  PCI\VEN_10EC & DEV_5229 & CC_FF0000

  PCI\VEN_10EC & DEV_5229 & CC_FF00

  PCI Simple Communication controller:

  PCI\VEN_8086 & DEV_1E3A & SUBSYS_183E103C & REV_04

  PCI\VEN_8086 & DEV_1E3A & SUBSYS_183E103C

  PCI\VEN_8086 & DEV_1E3A & CC_078000

  PCI\VEN_8086 & DEV_1E3A & CC_0780

  SM Bus controller:

  PCI\VEN_8086 & DEV_1E22 & SUBSYS_183E103C & REV_04

  PCI\VEN_8086 & DEV_1E22 & SUBSYS_183E103C

  PCI\VEN_8086 & DEV_1E22 & CC_0C0500

  PCI\VEN_8086 & DEV_1E22 & CC_0C05

  (USB) Universal Serial Bus controller:

  PCI\VEN_8086 & DEV_1E31 & SUBSYS_183E103C & REV_04

  PCI\VEN_8086 & DEV_1E31 & SUBSYS_183E103C

  PCI\VEN_8086 & DEV_1E31 & CC_0C0330

  PCI\VEN_8086 & DEV_1E31 & CC_0C03

  Unknown device:

  ACPI\HPQ0004

  * HPQ0004

  Hello:

  First install the chipset driver and reboot (will install the SM Bus controller).

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=ob-103010-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 5278311 & sw_lang=.

  Second: Install the AMD graphics driver and restart.

  For switchable graphics in your notebook, you install only the driver AMD, which installs the drivers for the AMD and Intel for the graphical configuration has your laptop. NEVER install the Intel driver only or allow updates to the Intel graphics driver to install.

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=ob-111285-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 5278311 & sw_lang=.

  Third: Install the audio driver and reboot.

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=ob-104672-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 5278311 & sw_lang=.

  Now, the rest of the devices can be installed...

  Ethernet controller:

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=ob-102604-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 5278311 & sw_lang=.

  Network controller

  http://h20565.www2.HP.com/portal/site/hpsc/template.page/public/PSI/swdDetails/?sp4ts.Oid=5229457 & spf_p.tpst = swdMain & spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_119873_1%257CswEnvOID%253D4059%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument & javax.portlet.begCacheTok = com.vignette.cachetoken & javax.portlet.endCacheTok = com.vignette.cachetoken

  Bluetooth controller

  http://h20565.www2.HP.com/portal/site/hpsc/template.page/public/PSI/swdDetails/?sp4ts.Oid=5229457 & spf_p.tpst = swdMain & spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_113004_1%257CswEnvOID%253D4059%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument & javax.portlet.begCacheTok = com.vignette.cachetoken & javax.portlet.endCacheTok = com.vignette.cachetoken

  PCI device

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=ob-102497-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 5278311 & sw_lang=.

  PCI Simple Communication controller

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=ob-102566-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 5278311 & sw_lang=.

  (USB) Universal Serial Bus controller

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=ob-102571-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 5278311 & sw_lang=.

  Unknown device

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=ob-116584-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 5278311 & sw_lang=.

• Slow to connect to the network computer.

  C7280 VIA Wired/Ethernet > Linksys wrt54gs i7 Desktop Core 6 GB RAM HP Vista 64-bit wired to the router & Toshiba L305 Core2 Duo 3 GB RAM Vista HP wireless

  I just installed a C7280 with all the bloated SW. Now everything works fine except when I boot the comps. they are very slow to connect to the network.

  Anyone encountered this problem?

  Alternatives?

  Thanks in advance.

  I read in this forum somewhere on a slow startup of PC and internet connection very late after installing the HP software. What has worked for them was to change the Startup Type of the service "Device HP CUE discover the Service" automatic to manual or automatic (delayed start). Why not give that a try.

• Photosmart HP 7510: hp Photosmart 7510 says it cannot connect to the network

  I can still print to the printer wireless to my computer, but when I try to FAX directly from my all-in-one he says that it is not connected to the network.

  When I check the settings, it IS connected.

  I had this printer/FAX/scanner for several years now and never had this problem.  I did not make any changes.

  I have unplugged it & tried... still can't FAX.  But I CAN always print it from my PC.

  Help!

  Hello @dtinstl!

  Thanks for posting on the HP Forums!

  Do to an eFax problem and some HP printers supporting the eFax service there is not much I can help in this regard.  I'll have to refer you to this post with instructions on what is done about this particular issue.

  Please see the message here: eFax explanation

  If you wish you can also contact our HP Cloud Services Department in this respect.  Please contact our Cloud Services at 1-855-785-2777.  If you do not live in the United States / Canada region, please click the link below to get help from your region number.  http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

• HP Pavilion 2 x 10-N000NA: HP Pavilion x 2 10-N000NA connects to the network, but not to the internet

  Hello

  I have a problem with my HP Pavilion 2 x 10-N000NA Windows 10, 32-bit version...

  I have a router TP-Link W9980 and the laptop connects to the 2.4 GHz network, but there is no internet access.

  However, if I use a range extender (powerline TP-Link Wireless extender), it connects to the network and the internet!

  So, I guess that the equipment is working well, there must be a setting somewhere?

  I've updated all the drivers, etc. for the laptop and the router.

  Any ideas?  Thank you.

  Hello

  Well, the strangest thing happened!

  There was a huge update of Windows, and it seems to have solved the problem.

  Connections now say '(network) secure' or '(network) open' - which they did not before.

  So now that I know that the network was very good and it was a laptop problem which needed fixing.

  However, I do not know what exactly the update fixed, so I can not pass on any knowledge to solve the problem of someone else who suffer.

• error "unable to connect to the network hidden.

  Hidden in my own home network

  I have 2 laptops. I can connect to the network wirelessly fine with 1 laptop. But the 2nd laptop says cannot connect to the hidden network. HOW CAN I VIEW IT?

  Hi WendellXD,

   
   
  1. who is the operating system installed on the computer?
  2. it worked earlier?
  3. have you made changes to your computer recently?
  4. What is the brand and model of your computer?
  5. you try to connect to the network through wired or wireless?
   
  I suggest you follow the link and check if it helps.
   
  Windows wireless and wired network connection problems

   

   

• "Cannot connect to the network." When you enter the correct password for wireless network

  Hello

  I have the HP Photosmart C7200 all-in-One series.

  This seems relatively insignificant compared to some of the problems posted here, but nevertheless it is a problem.  I have a Verizon FiOS (Actiontec) router.  I am trying to connect to it wireless; the network key is using WPA authentication.  I followed all the instructions in the quick start guide.

  My printer detects my network and application authentication key.  I enter the correct key, the printer is trying to establish a connection, but after about 15 to 25 seconds, I get the error message, "cannot connect to the network.  I know that my key is correct; I connect to my router very well through several laptops, PDA, etc.  I have reset the settings network default manufacturer and tried without success.

  I don't know what kind of trouble shooting I'm supposed to do here.  The printer detects the router (albeit low signal strength) whenever I try to connect, I enter the password each time and I get the error each time.

  Your help is greatly appreciated.

  Edit: I printed the test report wireless network, here are the results:

  Radio on   PASS

  The radio work   PASS

  Ethernet cable not plugged in   PASS

  Network name (SSID found)   PASS

  Security   PASS

  The printer settings compatible with the configuration of the wireless router   PASS

  No filtering   IN CASE OF FAILURE

  Connected   Not work

  The signal strength   Very low

  Other networks detected matching you the network name (SSID)   NO.

  I know this sounds strange, but try changing channel by channel 11 of the wireless router.

• I can't connect to the network wirelessly with my Emachines eM350 portable because I get the automatic Wireless Configuration error, see Article 871122.

  original title: WiFi

  I can't connect to the network wirelessly with my Emachines eM350 portable because I get the automatic Wireless Configuration error, see Article 871122.

  I use a Huawei E585. I simply want to clamp it alll in the tray.

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  (1) make sure that u run "NET START WZCSVC" on the command-line as soon as u Ouvrezunesession WINDOWS XP (START, RUN, NET START WZCSVC (command line)).

  (2) START, CONNECT, WIRELESS INTERNET CONNECTION

  --> under the 'GÉNÉRAL' tab: (1) right click on the wireless Internet connection; (2) click on properties; (3) make sure that all THE ELEMENTS under the title "THIS CONNECTION USES THE FOLLOWING ITEMS" are COMPLETELY FUNCTIONAL, i.e. UNCHECK THE ONES THAT DO ARE NOT ACTIVE ~!  (I recently turned off AVG and that this item has been inadvertently clicked on ~!) ;

  --> on the 'ADVANCED' tab: run the NETWORK CONFIGURATION WIZARD to reset your network

  3) http://support.microsoft.com/kb/871122 --> RUN 'DIFFICULTY CE PROBLEM' (ms - fix 50469)

• Unable to connect on the internet on another computer - "Windows could not find a certificate to connect to the network (named).

  When I try to connect to internet on my other computer I get a message saying "Windows could not find a certificate to connect to the network (name)". It's only since I've had a second computer as it does on my old computer which is

  a laptop HP Pressario with Windows XP Home Edition. Someone told me to go to authentication in wireless networks, but can highlight something here as everything is gray.

  Hello

  · What type of encryption do you use on the router?

  · You have the latest drivers for your wireless network card?

  Make sure the authentication IEEE 802. 1 x wireless card is disabled, and check if that helps.

  a. Click Start, then select run.

  b. term ncpa.cpl type dialog box and then click OK.

  c. right click on wireless network connection icon and select Properties.

  d. click the wireless network tab.

  e. click on the properties button next to remove it.

  f. click on the Authentication tab, and then clear the authentication 802. 1 x IEEE select this network check box.

  g. click OK to update the settings.

• After installing winows xp SP3, cannot connect to the network wireless at home

  My daughter has an old windows xp pc. I have a USB wireless adapter attached to it to our wireless here at home. When I install SP3, the network card does not connect to the network.  I have uninstall xp3 to make it work. I even reinstalled the software for the card after xp3 installs, and it still does not work. What can I do about this problem?

  Go wireless adapter manufacturer and obtain an updated driver, then it should work. If the manufacturer does not, for a search on the Web.