Photosmart HP 7510: hp Photosmart 7510 says it cannot connect to the network

Similar Questions

• HP Photosmart 5520: HP Photosmart 5520 not shall be connected to the network or print.

  Our printer working fine until a couple of days. Now, when we print dialogue print open but constantly says "the printer is not connected. I tried to connect to the router using the screen of the printer, but get a message saying "cannot connect". I rebooted everything what it many times.

  At some point during those two days, I have managed to get so our imac had found the printer and actually thought it was printing, but nothing only happened at the end of the printer. Now I'm back to "the printer is not connected. I don't know what caused that change or change it back.

  Someone had mentioned to a static ip address in the printer, so I tried this (assuming I did it correctly) passing through the settings - without wire-advanced settings-ip settings-manual where it says ip address no connection, then put an address ip, but this was not accepted and always says 000.000.000.000.

  The Test report suggested allowing MAC wireless network could be the problem, but somehow, I spent (don't know how) and the latest report ' NECK until low but above indicates a problem IP address by saying that our ' HP printer is currently configured with an IP address of auto. On most of the networks that it will prevent your printer to communicate on the network... run the next solution." The solution suggested to restart then print a new test report and then says "check that the printer has received a DHCP IP from your network router address, check the configuration source in the current configuration of the report section - it should show DHCP. But after I restarted again the ip address shows 0.0.0.0 and the configuration source said no "specified." The test report gives no solution to change the ip address to view DHCP so I'm stuck. My Advanced settings still say IP settings - automatic. Help appreciated. Thank you. P.S I'm not good with all this talk about techy but I am surprised that, in my opinion, I understand what I wrote!

  I removed the ssid password and managed to print. I put the password, it is lacking in WPA WPA2 & (I have not WPA2-AES) and again the printer cannot connect. The printed report again now says FAIL to no filtering and implies that there is something to do with active mac filtering which I don't understand. Thanks for your help so far. We are called to take the kids to the movies can be on so not for awhile.

• Computer Windows Vista says it is connected to the network 4. I don't know what is network 4.

  on the bottem of my screen where the icons were similar to the he mcfee icon and symbol of volume there is a picture of 2 small computer screens, and when I scroll above him, it says connected to the network 4. I don't know what network 4 is and I have never seen this before and the other day I saw him and it says connected to network 2. I would like to know if anyone can help me in this matter. What network average 4?

  original title: bottem icon

  This icon is the icon of your network. You don't say what kind of network you are using. However, I will give you an example. If you repeat your network connection or use a network USB key and plug the key to another USB socket and create a new Windows login will name each new connection 4 then 2 then 3 and so on. You can rename the connection to your liking. To rename the link to right click on the network icon in the notification bar, click Network and sharing Center, click on manage network connections, right-click your network connection icon and click Rename.

• Photosmart HP 5510: printer not connected to the network, although it

  Hi people,

  I am at my wits end with this and you are my only hope (what Star Wars quote).

  I have a HP Photosmart 5510, I've had around 2011.  I've always used it in the company of my iMac (OS X now on El Capitan). Over the last year or two, there was the strange number to which case when I open the HP utility on my iMac it says it is not able to connect to the printer and I should check that it is switched on (this is before you ask). This question seemed to resolve itself after a short while and there was no problem.

  However, I came to analyze some elements of the other day, and this same old issue again raised his head. I put my paper on the scanner and press the option scan only for the printer to tell me that there is no connected computer. Weird, I thought I had printed only some points the day before. I went to my iMac and open the HP utility to see my former favorite message that the printer was not plugged in blah blah.

  I went on HP website to see if there were new pilots required, which it was not (the last was for OSX Yosemitie!).

  I decided to try and start fees and remove the printer and re - add new. I deleted the printer, downloaded the latest HP deriver (just in case) and that's where everything went wrong.

  Software downloads, all right, it starts going through the installation process, end, then he gets to the selection of the device, issue. It evokes three devices that are my one and only printer (Strange I thought). Two with the "connection type" listed as Hello and the other with the connection type is listed as IP. I tried selecting each of these only for each of them to come back with the following error message:

  "YEAR error occurred while the communications device." Please make sure that the device is ready and try again." Well, if they hear by loan, circuit implementation, its connected to my network then YES ITS BLOODY LOAN! So I get no more on the process by the printer and HP Utility installation is nothing else than a large black plastic paper weight. I tried to reconnect my printer to my network wifi several times and everything is fine, its connected and there is no problems according to the page of "wireless network test results" print.

  What the hell is happening? Any ideas? Please save me before I throw this thing by the highest window that I can find.

  I'm not a computer expert and I'm certainly not a network specialist. All the advice is appreciated greatly and fortunately.

  Hey @Mvdarbs,

  Welcome to the Forum from HP Support. We're here for another help to get the most out of our products.

  Thank you for your message. I see that you experience the Mac-to-printer communication problems when you use the HP Photosmart e-All-in-one 5510 printer. All this happens despite your apparent WiFi connection. While it is no doubt frustrating to live when all you want to do is print, there are solutions that you can try and I hope that they will restore the regular feature.

  I recommend you try the following steps:

  (1) we will start over with the installation of your network printer. From the control panel press the wireless icon, and then select "Restore network Defaults."

  2) façade, run the "Wireless Setup Assistant." Reconnect to your home network and then make a note of the IP address.

  3) visit the printer embedded web server (EWS): this is done by entering the IP address of the printer in the address bar of the web browser and navigating to this address. If you have a security alert (as this page is not encrypted), click on to "Go forward anyway." If the page loads correctly, we can be certain that the network connection is real. While you're there, make a note of any error messages or status alerts (if you see it, it's all good) and don't forget to advise me on what you see.

  4) remove the printer from your Mac. If you are not sure how, refer to the

  guide for advice.

  one) (optional)-set a static IP address for your printer. Refer to this thread of @PrintDoc here: http://h30434.www3.hp.com/t5/Printers-Archive-Read-Only/changing-IP-address-for-wireless-printer/td-p/445087 for instructions on how to do it.

  5) reinstall your printer: click here and install the driver that you are prompted.

  Please let me know the result of your troubleshooting by responding to this post. Don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  See you soon,.

• HP Photosmart 7520 will not be connected to the network

  The printer is plugged directly into the wall.

  The printer network settings are stuck in automatic mode.

  When I select IP settings manual, the printer displays buttons for IP, Netmask, GW and DNS.

  If I enter an IP address for one of them and try to enter one IP address for another, the previous (s) are deleted.

  If I enter any manual adjustment of property intellectual and then return to the parameters of intellectual property, it shows automatic again and all my entries are deleted!

  I have reset the default network settings and that this problem persists!

  Do I have to return this printer and get another brand?

  8 points of view and no one seems to have any idea how to resolve this.

  I'll return the printer.

  Consider this resolved.

• I try to log into Microsoft Flight Simulator Game spy. I get the message saying unable to connect to the network. I have FSX Gold edition. What can I do to make it work again?

  Please read above.

  Hello

  The question you posted would be better suited in the Forums of Simulator. I would recommend posting your query in the Forums of flight simulation.
   
  http://www.flightsimulationforums.com/
   
  I hope this helps.

• FSX won't turn on, says that it cannot connect to the server

  Hey, I tried to register my copy of Microsoft flight simulator X deluxe edition and it does not work I tried to register it hourly it says it cannot connect to the server);

  Hello

  What version of Windows operating system do you use?

  I suggest you to consult the following Microsoft article and check if it helps.

  
  Solve problems with activation for Microsoft games problems and mapping programs
  http://support.Microsoft.com/kb/960480
  
  Note : the steps mentioned below includes the modification of the system registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
   
  Back up the registry: http://windows.microsoft.com/en-US/windows7/Back-up-the-registry
  Also see: frequently asked questions on how to enable Microsoft Games for Windows, streets and trips and Mappoint: http://support.microsoft.com/kb/927007

  If you still experience the problem, then I suggest to contact with support of Flight Simulator for further assistance.

  http://support.Microsoft.com/GP/games-for-Windows

  http://www.Microsoft.com/products/games/FSInsider/tips/pages/default.aspx

• Photosmart 7510 will connect is the network (mac) wireless

  Although already our Photosmart 7510 used to connect wirelessly to the network, it arrested recently, without a known cause. I've updated all the software. It is said on the printer that is connected to the network and print via usb cable but the computer says that it is not connected (or on any other laptops 3 mac at the office also connected to the network).

  As I said, I've tried updating all software and have tried to delete the printer via reset printing system by following the instructions on a previous post. However I now can't add the printer as was then ordered.

  The software used is

  Mac OS X Lion 10.7.5

  Any help would be great, printing via USB is such a pain!

  Thank you

  Hello

  Try unplugging your router to power for 30 seconds, plug it back in and look for any change.

  Also, try power cycling the printer.

  If it persists, reset the network settings and reconnect it to your network, you can find steps planned in steps 3 and 4 below:

  http://support.HP.com/us-en/document/c02948582

  So, you can try to reset the printing system and check to see if that can help you:

  * Be aware that reset the printer system will eliminate any existing queue and reset all custom settings driver.

  Click on the Apple menu and then click on System Preferences.
  Select Print & Scan.
  Right click (or Ctrl + click) your product with the Printers list in the left panel and then click on reset printing system.
  Click OK to confirm the reset.
  Type your user name and password.
  Click OK. The printing system resets.

  Try to add the printer by clicking on the sign more and check any change.

  If none of the steps above does not help, have you changed anything lately? a new router, etc.

• Photosmart 5220 went offline, not connected to the pc

  Photosmart 5220 is no longer connected to the PC. Used to work perfectly, assistance contacted, can not help you.

  President made,

  Here is a link to a document that should help you resolve your problem.

  http://support.HP.com/us-en/document/c02221706

• Photosmart more B210b: printer not connecting to wireless network

  I try to install the printer, which has worked before with a different wireless router. I can't connect to the network, even if the print network configuration page says PASS and YES at all the right place with this new router (DB of Belkin Wireless Router N600DB).  When I connect to the router, the printer does not appear in the list of connected devices, but the printed page says it IS connected (has assigned IP address192.168.1.100 on the page). When I try to install the device and connect it to the laptop computer, the IP address is not recognized.

  Both devices are in the same network (belkin.b2.c)

  I've completely disabled the firewall, I install it, both in the protection antivirus software, windows AND router, have revived all 3 devices (printer, router and laptop), but still unable to connect.

  I'll be very grateful for your help.

  JorgeAV wrote:

  Thank you Dragon-fur

  I have a problem with your suggestion and a question.

  First problem: I can't change the SSID name or to change other settings of the printer because I can not connect at all.

  The question is, I see my router dashboard that the Pool of IP address of departure is 192.168. 2.2 and the Pool of IP address is 192.168. 2.200 now, IP address, I can see the printer is 192.168. 1.100 as you can see, the range is different. This could be a problem?

  Comment

  The printer is on a different subnet from the rest of your network.  Yes, it's a problem.

  The printer and the router - and indeed, the rest of the network - these must all be on the same subnet.  Any network - but they are to be on the same.

  For example:

  It is not important whether you choose 192.168.1.1 for your gateway router

  OR

  whether you choose 192.168.2.1 for your gateway router

  The rest of your computers, printers and devices must be on the same network of "sub" as the gateway router.

  You can try changing the IP of the printer on the printer control panel if you can't connect with EWS (built-in web server).  Push the printer over subnet 2.

  Maybe give printer IP address: 192.168.2.226

  Click on the button the printer wireless...

  Click on the thumbs-up Kudos to say thank you!

  And... Click on accept as Solution when my answer provides a fix or a workaround!

  I am happy to provide assistance on behalf of HP. I do not work for HP.

• Hello my iPhone 6plus does not connect to the network on the upper left side of the screen it ust say research

  Hello my iphone 6plus does not connect with the network on the upper left side of the screen it say research

  Have you ever tried troubleshooting mentioned in this article?

  If you cannot connect to a cellular network or cellular data - Apple Support

• OfficeJet 4630: Says printer connected to the network, but computer says that it is not connected or idle

  I can't print to our hp officejet printer range 4630.  The printer says that it is connected to our home wireless network.  However, he said that it is inactive or not connected to the network on my mac.  The only way it will print sometimes is if I switch to a wireless network that is named the same as the printer.  AirPrint does not work.  We have a Linksys router.  Not sure if this is the problem or not.  I ran all kinds of diagnostic impressions on the printer and all say that it is connected.  I also tried to put the ip address into my web browser and it does not find the printer when it is connected to our home network.  Help, please!

  Thanks for trying my earlier recommendations. In my view, the problem you are experiencing may be with your wireless router. Normally, I would have you make sure that it is configured correctly, but you cannot access the built-in Web server.

  I want to try to set a static IP address, so we can try to get in the EWS. Please continue here: printer does not maintain the wireless connection

  A little luck? If you were able to set a static IP address, please try and access the built-in Web server. Follow the steps below:

  1. open EWS (use my earlier recommendations) printers

  2. go to the Network tab

  3. network protocols

  4. Select enable IPv4 ONLY

  Now with IPv4 enabled, you should be able to print wireless.

  If this isn't the case, you will need your router company to make sure that the multicast is enabled, Hello Protocol is enabled, mac filtering is disabled and ask them to check if there are updates the firmware for the router and the router's firewall check to make sure that it does not obstruct the communication

  The following ports are also used by your HP device and may need to be opened on your firewall configuration

  Incoming (UDP) ports are ports of destination on the computer while outgoing ports (TCP) are ports of destination on the HP device

  Incoming ports (UDP)

  137, 138, 161, 427

  Outbound ports (TCP)

  137, 139, 427, 9100, 9220, 9500

  The ports are used for the following functions:

  Print

  427, 137 161 UDP ports

  TCP port 9100

  Download of photo card

  137 138 427 UDP ports

  TCP 139

  Scanning

  427 UDP port

  TCP 9220, 9500

  Faxing

  427 UDP port

  TCP port 9220

  Installation of device HP

  427 UDP port

  Web Services

  80, 443, 5222 and 5223

  Any change? I appreciate your persistence!

• HP Envy 4500: Printer says it has solid network connection, but cannot connect to the internet

  So I have not been able to use my printer wireless lately, so I decided to check if it was connected to my wireless network. It is; I checked, re-connected and checked several times. So I decided to reactivate my web services. I have them turned off, and now whenever I press the button on the printer ePrint, it says connection for a really long time and then displays the message in the sense of "the printer cannot connect to the server. Check the internet connection and proxy settings.

  I have re-connected the printer to my wireless network, I checked that if I use a proxy server (I'm not), I used the HP print and Scan Doctor - just, it won't just matter what I do.

  All I can think about is the fact that I have recently purchsed a new router, but says that its connected which is what really stem me.

  This printer makes me crazy - please help

  Hi @mastersword64,

  Welcome to the HP community!

  I hope you have a pleasant experience with us.

  I want to help you with the connection error, you get on your e-all-in-one of HP ENVY 4500 printer when you try to enable web services.

  Here are some steps, I suggest trying to get your web services up and running it again:

  Network Power Reset:

  We'll leave the router and unplug the power cable (NOTE: do not reset the router.), and then do the same with the printer and shut down the computer. After a minute, plug in the router, wait to fully turn on, then plug the printer back in and wait for the wireless light become solid. Once the router and the printer are on, go ahead and re - turn on the computer. This will refresh the network connection.

  Restore the default settings of the network and reconnect:

  1. on the front panel of the printer, press your up wireless icon

  2. Select settings.

  3. Select restore default network settings.

  4 turn on your printer.

  5. once it is initialized to save, press the wireless icon again.

  6. Select settings.

  7. Select Wireless Assistant , and then follow the prompts to enter the details of your wireless network.

  8. try to activate the web services again.

  Configure a manual DNS for your printer:

  1 obtain the IP address of your printer

  a. This can be done by pressing the icon on the printer wireless.

  2. Enter the printer's IP address in a browser on your computer.

  3. Select the tab network at the top of the page.

  4. on the left, select network.

  5. Select network address (IP)

  6. Select manual DNS server

  a. manual Preferred DNS should read 8.8.8.8

  b. alternate DNS server should read. 8.8.4.4

  7. Select apply. You can get a warning simply select OK.

  Please reply to let me know if these steps resolve your issue.

  Good luck!

  

• I'm trying to update my ipad (first edition) to the new version and after about an hour, I get a message that says unable to finish because the network has expired.

  I'm trying to update my ipad (first edition) to the new version and after about an hour, I get a message that says unable to finish because the network has expired.  How can I fix it?

  Original title: network programs network networking Internet Web site Site Web Web Site URL

  Hello

  You need to support iPad not Microsoft.

  iPad - media choices
  http://www.Apple.com/support/

  iPad - Support
  http://www.Apple.com/support/iPad/

  iPad - communities (Forums)
  https://discussions.Apple.com/index.jspa

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• I have norton antivirus online via my ISP and I had to disable, because it comes with an error that says "cable not connected or missing network adapter" I use dial-up.

  cable not connected network adapter

  I have norton antivirus online via my ISP and I had to disable, because it comes with an error that says "cable not connected or missing network adapter" I use dial-up and do not use any type of router and I'm not on a network. I also tried to disable my network card & it still says the same error. I have an internal network card that came w / the computer (NOT a PCI one) and I wonder if there is a cord or a plug inside my computer that must be plugged. I made some changes on the internal hardware and might have missed an and I didn't have to open my Tower if it wasn't. It's a big hassle! Help, please!

  Hello

  1. Once you get the error message?

  2. do you get the error when you try to disable Norton anti-virus?

  3. are you able to access the Internet explore?

  Temporarily disable the antivirus on the computer running software and check if you are able to install the software.

  Disable the anti-virus software

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  WARNING: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.