Why graphic ActiveX lagging during the race?

Similar Questions

• Satellite A300 power suddenly goes out during the race for hours

  Dear users of the Forum,

  I am facing a strange problem in operation.
  My laptop Satellite A300 is suddenly down power during the race for hours.
  It is auto off not exactly. Not the way windows stop, is rather like strength to off (as when I press on & power button to stop force).

  This happens automatically, starting again, the screen saying "windows does not stop properly, start windows normally" is apperanig.

  I suspected virus infection, I tried full scan with nod 32, essential microsoft, kaspesky - 1 by 1 (previous uninstall and install the new), but all the antivirus intremediately scan stopped due to this power off.

  Watch movie also stopped in the Middle, attempted to convert the movie file format also was arrested several times because of this problem of automatic disconnection.

  I tried to run only on the power (remove battery) and got the same result.

  can anyone identify the problem? can you please give me the solution?

  smarjit1

  Hello

  I put t think it is s virus.
  En me it looks like overheating. Eventually the high internal temperature requires the laptop to close. This is done automatically to prevent the equipment from damage
  I'm not quite sure what could cause this exactly, but in most cases the dust inside the fans affects cooling performance and lead to a temperature higher than m.

  Higher temperatures could affect the RAM modules too, and perhaps that is the reason why some applications don't work properly.

  What to say; try to clean the cooling fans using a jet of compressed air and check out how the laptop would proceed

• Apple Watch freezes during the race

  I used my Apple Watch during a 21K run. I used the training software to monitor my heart rate during the race.

  After the mark at halfway, the screen dimmed, and the screen froze. (stopped adding distance, and heart rate has been replaced by '-'.)

  thinking that it was because of the excessive sweat on the sensors, I tried to wipe the back of the better watch that I have (which is not a lot considering everything that I had on me was wet). by pressing the digital Crown to return the screen to the face of the watch, but whenever I go to the app to drive he would show the same frozen screen.

  It is only after a kilometer (about 7 minutes) made the response to training app and worked normally until the end of the race.

  for the purposes of the workout on my Apple Watch concerns, I had only run 19,71 km instead of the 21 K who I actually ran.

  question: How can I prevent this happening again?

  Hello

  As a first step, if you have not already done so, it can help to upgrade your iPhone and Apple Watch to the latest version of the software, from your iPhone:

  • Update the software on your iPhone, iPad or iPod touch - Apple Support iOS
  • Update the software on your Apple Watch - Apple Support

  It can also help to revive your watch:

  • Restart your Apple Watch - Apple Support

• Opengl32.dll is not designed to run on windows or it contains an error. I reinstalled the graphics drivers. During the execution of the games, it shows this error. What should I do to fix this?

  Opengl32.dll is not designed to run on windows or it contains an error. I reinstalled the graphics drivers. During the execution of the games, it shows this error. What should I do to fix this? Is it a graphic file or a file from microsoft?

  Hi Jason,

  1. What is the number of brand and model of your system and graphics card?

  2 did you a recent software or hardware changes to the system?

  This error can be caused by an application, including any old games you have installed on your system.

  Because you tried to reinstall the drivers for video card, you can try to perform a clean boot and check if it helps.

  A clean boot to check if startup item or services to third-party application is causing this issue.

  You can read the following article to put the computer in a clean boot:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  Note: After troubleshooting, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

• How to set the name of the author and where I find all of the debug option token during the race or the creation of the application on QNX IDE?

  How to set the name of the author and where I find all of the debug option token during the race or the creation of the application on QNX IDE?

  Here is the error

  Failure of deployment: Info: request shipment: install and launch
  Info: Action: install and launch
  News: Native debugging: on
  Info: File size: 219949
  Info: Installing com.example.UIBB10AppTest1.testDev_B10AppTest15dd51c62...
  Info: Treatment 219949 bytes
  actual_dname:
  actual_id:
  actual_version:
  result::failure 881 the application author does not match the author token of debugging

  The author information is located in the bar - descriptor.xml in the tab "General". But the information must be defined automatically. In addition, you must install the token debug on your device.

  If everything is configured properly there is only one problem that happened to me. I had several chips debugging Momentics. I had to remove all chips debugging and leave alone the I want to use. Perhaps, you have also several debugging chips installed in Momentics. This seems to be a bug in Momentics who can't handle several chips debugging.

• Compiling jsx to jsxbin, Palette disappears during the race

  Hello world

  My ID version is CS5, I added # targetengine "session."

  I compile jsx to jsxbin, but the palette disappears during the race.

  Anyone can tell me the reason?

  Thank you.

  Best regards

  Goldbridge

  You can wrap the content of jsxbin inside app.doScript () routine and add engine target in front of her.

  

  Hope that helps.

  --

  Marijan (tomaxxi)

  http://tomaxxi.com

• Why firefox clear URL during the night

  different URLs (websites) disappear during the night, from the search bar. I put them back in and use the arrow down during the day, through the night, they disappear. Any suggestions

  Hi luapg,

  1. Click the menu button

     

  2. then click on Options.
  3. Under history, make sure it is set to the Firefox will: story to remember

  Make sure also that under the address bar, the history is checked.

  If you run any kind of PC cleaner which could also be compensation history of Firefox that will keep him to suggest Web sites.

  Alternatively, if you click on the star to bookmark the Web sites then Firefox will save them permanently.

  If you try, under the address bar, Favorites is checked.

  Let me know if that solves your problem.

  -Curtis

• Why graphics appear intermittently in the file Edge browser animate?

  Hello, I have a dashboard project animate that runs and displays well in Edge, but once published, some of the svg graphics appear only intermittently in a browser. For example, it displays well in Chrome a moment, but then a few minutes later, when I go back exactly the same file (same version) in the same browser (same version) svg graphics disappear. See the example below. In this case do not display Snow Hill, the body and the Penguin hat.

  I would like to add that in Firefox it plays perfectly, graphics chrome appear intermittently and in Safari without animation poster at all - only the background image. On my iphone display graphics intermittently with no. and on Android sound, the animation is slow at first but plays with no sound.
  
  Here is a link to the file online:
  

  http://vervilleinteractive.com/ecards/su_holiday_2015/Jones

  Here is a screenshot of the problem below:

  

  The project dashboard files animate editable are zipped and attached here as well: http://vervilleinteractive.com/ecards/su_holiday_2015/holiday_jones_final_v2.zip

  Thank you for advice or suggestions you may have!

  -Joy

  The project files you provided by download are 35 MB - I think if you try to reduce some of the size of the files as much as possible, you will get much more smooth results

• PC Lag during the game

  I have a lot of delay after installing the game Dragon Age: Origins. My pc meets the requirements and all, but even if I did my utmost to improve the performance of the system I have a lot of lag. My system specs are as follows:

  Processor: Intel (r) Core Quad CPU 2 .40GHz

  (Vivid RAM) memory: 2 GB

  Graphics card: Nvidia 7100

  Your video card does not meet the minimum specifications

  http://EU.dragonage.com/theGame/index.asp

  • MINIMUM SPECIFICATIONS
  • OS: Windows Vista with SP1
  • CPU: Intel Core 2 (or equivalent) running at 1.6 Ghz or higher
  • RAM: 1.5 GB or more
  • VIDEO: ATI Radeon X 1550 256 MB or higher
    NVIDIA GeForce 7600 GT 256 MB or greater
    DVD ROM (physical copy)
    20 GB of disk space

• Why my video stop during the ram preview?

  I have adobe after effects cs6 and I click the ram Preview button and it begins to make the green line through my video, but it stops during rendering and he started playing my video only where it made which is not even close to rendering finished. I tried just add this option to display the queue and make just outside, but the result is a video slowmo. Also, when I import the video, the video is in slo mo so I decided to look to fix RAM but he stopped and played at full speed, but only a small part of it, please help.

  FAQ: Why preview RAM only play in my composition?

  FAQ: Why my huge output file, and why didn't he play back smoothly in a media player?

  Start here learn After Effects:

  http://Adobe.LY/AE_basics

• Satellite L650-123 - computer lag during the CoD game

  I've had this computer for a little while now, and it lags when I play games. The shift appears every time when I play Modern Warfare 2 and it lags even when I play Age of Empires 3. The computer is running smoothly for 2 seconds, then he accuses a delay 2 dry again, then lag... I guess this isn't memory (8 GB), or the Ati Radeon HD 5650. So can someone tell me where to find the problem? Or do I have to take my computer to the service?

  Thanks for your help!

  your computer is enough power to run modern games (memory (8 GB) and the Ati Radeon HD 56500). I'm not a gamer. I advice allows you to install the latest driver of display [Page Driver Toshiba | http://eu.computers.toshiba-europe.com/innovation/download_drivers_bios.jsp]. Enable] set high performance in the power Plan, check if the latest version of directx:

  http://www.Microsoft.com/games/en-us/aboutGFW/pages/DirectX.aspx

• Satellite A50 - goes out of himself during the race

  my laptop turns off itself during its operation and am working on it. I already checked the connection ca; even the battery is ok.

  Can it be a problem of the cooling module? The fan runs all the time and the laptop gets very hot.
  There are solutions to this problem?
  It is impossible to work with the laptop that turns off when processing...

  Thanks for the suggestions...

  Hello

  This sounds like an overheating problem.
  To my knowledge the operating system can the laptop will stop if the temperature increased at the critical level.

  You know that each device preinstalled in the notebook produced heat.
  Sometimes more operating devices with maximum performance. The devices run with maximum when performance performance heavyweight like games runs on the laptop.

  On my laptop Toshiba power saver determines the method of cooling and the processing speed of the CPU. I think that this is also preinstalled on your laptop. Therefore, you should first check these options.

  In addition, you should check your module cooling fans. Sometimes the dust and debris keep the laptop cooling properly.
  You must also have sufficient free space around the laptop for cool air circulation.

• Changing the duty cycle of PWM on during the race

  Hello

  I am trying to generate a my C Code PWM signal.

  It works fine except for the fact that I can not change the operating factor during execution of the generation of PWM signals.

  Here's what I do:

  //Init DAQmxCreateTask("masterP",&task_pwmout);
  DAQmxCreateCOPulseChanFreq(task_pwmout,taskchans1,NULL,DAQmx_Val_Hz , DAQmx_Val_Low , 0.0,freq,duty);
  DAQmxCfgImplicitTiming(task_pwmout,DAQmx_Val_ContSamps,1000);
  DAQmxStartTask(task_pwmout);
  
  ...//Stop DAQmxStopTask(task_pwmout);
  

  It works well, but the duty cycle is fixed.

  I tried to change the cyclical report but it seems that the only way it works is like this:

  //Init DAQmxCreateTask("masterP",&task_pwmout);
  DAQmxCreateCOPulseChanFreq(task_pwmout,taskchans1,NULL,DAQmx_Val_Hz , DAQmx_Val_Low , 0.0,freq,duty);
  DAQmxCfgImplicitTiming(task_pwmout,DAQmx_Val_ContSamps,1000);
  DAQmxStartTask(task_pwmout);
  ...
  //Change Duty Cycle DAQmxStopTask(task_pwmout);
  DAQmxSetCOPulseDutyCyc(task_pwmout,taskchans1,duty);
  DAQmxStartTask(task_pwmout);
  ...
  //Stop DAQmxStopTask(task_pwmout);
  

  I have to stop the task, set the new cycle and restart the task.

  Unfortunately, it takes some time (~ 100 ms) which means that during this time, the PWM is turned off.

  Is there a way to change the smoother operating factor, so there is no gap between?

  Thanks in advance.

  Christian

  Hi Christian,

  You are right. Stop a restart of the task is a very slow way to adjust the pulse width. This page describes the option adjust the factor of market during execution by using the function "DAQmxWriteCtrFreqScalar". By calling this function in a loop, after the start of your task, you will be able to adjust the frequency and factor use of your task, simply by changing the settings.

  I would like to know if it works for you.

  Concerning

• Why my hard drive frequently the race, for an extended intermittently?

  My hard drive accelerates frequently (even when I'm not using it) and seems to be racing (for up to 30 minutes at a time). It seems that the computer is actively working on something and runs very slowly if I try to open Explorer or Outlook. The events come & go and can fluctuate quickly. It's driving me crazy. It's noisy and irritating. Don't know if it's a software is automatically updated (eg. Updates Windows or PC Tools antivirus). I did all the checks the system, etc. defragmented. The machine runs well between these events. System checks do not seem to identify all errors. A recent check by a technician after a blue screen error, identified faulty RAM, since replaced, but not other issues.

  I suspect it has something to do with the analysis of the components of the PC Tools software in real time.  According to the options you have installed/enabled, you do not have to all or they are in competition with other things.

  What is your version of XP and the Service Pack?

  Do you have other AV tools installed such as McAfee, Symantec, Norton, Spybot, AVG, Avira!, MSE, Panda, Trend Micro, CA, Defender, ZoneAlarm, Comodo, etc..

  You can temporarily disable PC Tools and see what things look like.

  You needn't Download Process Monitor.

  You need to download Process Explorer from here:

  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896653

  You'll like Process Explorer when you get the hang of it.  Process Explorer is the Manager of Windows taskbar on steroids.

  Process Explorer installs nothing so it won't slow down your system since it works only on request.

  Process Explorer can seem a little intimidating at first because it has so much information, but you will begin to make love the way it works when you're looking for performance problems.   You can even say EP you want it to be your new default 'Task Manager' value in the future.  You can always run the original tasks as Manager.

  Once you get Process Explorer running, expand the columns, made drag the corners of the screen for it's largest, etc., so you can see as much information as possible in the window.  Now you can really see what is running on the system.

  Here's a screenshot of my poor system when I use Process Explorer:

  http://img222.imageshack.us/img222/2567/ProcessExplorer.PNG

  The small window at the top right shows graphic things.  Each window is a different as rolling graph:

  CENTRAL PROCESSING UNIT
  Validation of the system
  Physical memory
  Network
  Disc
  E/S

  Roll your mouse over each small window to see what it says that you can see what they are doing.  Double-click the window to make it bigger.

  If your drive is too busy, look a peak in the disc window or double click it to make it bigger.  When you see a spike, you pass the mouse over it and it will tell you the process on your system that is the cause.

  For the experience, when PE upward and running and things are settled down, choose Tools in the properties of your HARD drive and then scan your HARD drive for defragmentation.  You don't need actually to defragment the volume since that take too long - just it will analyze and watch the graph of disk in Explorer process for the tip.

  When analyze you the volume for fragmentation, see the drive activity in process Explorer and hover your mouse over the edge and he'll say dfrgntfs.exe, so now you know that cause the Spike.

  Close all applications that you don't need to your troubleshooting so that they don't clutter things, is PE up and running, let things settle down and wait for the fly and the outbreak in the graph of the disc, hover your mouse over the edge and find out who is the culprit.

• Why my photos corrupt during the transition from XP to Vista?

  I recently bought a new Pavilion p6140f PC with Vista Home Premium installed.  When I transferred my pictures of my old XP system to it, a large percentage of them appear corrupt.  When you go into the records, initially the thumbnails load up the fine (the photo looks good), but a second later the thumbnail appears corrupt (half, discoloration, misalignments plans).  When I click the image, it loads under the corrupted form.  I tried to clear the cache of thumbnails with HP support, but it does not work.  Is it possible to recover my pictures?  It seems that somehow be ok since the thumbnails first then load corrupt.  Any help would be appreciated.

  Hello

  I work as an IT Pro also, but came to the same question as the above posts:

  I have the same problem with Windows 7 x 64 (final, no beta version): after downloading images using my card reader 5 to 10% of the images get corrupted. At first I thought there was a problem of transfer: copy of the files on card for hard drive often gave me an uncorrupted image - after trying 1-5 times.

  So the source images should be OK.

  So I thought it's my hard drives (I have 2 hard drives in reverse [not windows RAID software but the motherboard includes a]) and I replaced two hard drives.
  ---> same result: copy the files to a card reader (also tested different ones before replacement of disks) on disk HARD destroyed images (JPG and as I have * just * also performs RAW (Canon) files).

  Also, I can't find any information on the net about it - especially not for win7.
  I'm afraid there is a real problem with win vista / win7 - perhaps with special chipsets?

  During my win7 beta-test (more then half a year) moved never this problem.

  If someone finds a solution, please post here...

  Thank you and best regards,
  Thomas

  =================================
  The following link might be worth a visit.

  FastPictureViewer WIC Codec Pack RAW
  A free collection of 32 and 64-bit raw image
  decoders for Windows 7, Vista and XP
  http://www.FastPictureViewer.com/codecs/

  John Inzer - MS - MVP - Digital Media Experience - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - * proceed at your own risk *.