Why is a replacement wireless card does not let me start my computer?

Similar Questions

• Satellite 1905-S303 PCI Wireless card does not start code 10

  I put a PCI BCM94306PM broadcom wireless card in my laptop. The laptop is equipped with led however one is damaged and can not be connected, these cards may work with only one side and I even read somewhere that they can work on a short range with no led. My problem is the Device Manager indicates that the device cannot start code 10. I have a fresh install of XP Pro SP1 (not from the original restore disk). With this in mind, I think there must be some Toshiba utility or the missing driver to allow the map to work. Any help appreciated.

  Hello

  Code 10 means that it is not present, not working not properly, or does not have all the drivers installed.
  In this case you need to download the latest driver on Toshiba website and install it.

  Best regards

• Satellite P750 - wireless card does not work

  PSAY3A - 02q 001. Laptop is around the age of 20 months. Turned on this afternoon and the Wireless does not work. Atheros AR9002WB-1NG. Can't b on / off switch material. The switch will beep when pushed. Network troubleshooting indicates the card is not activated. Card is always detected in windows.

  I feel that this indicates that the card has failed. Any thoughts?

  was soon Simon

  > Card is always detected in windows.
  Does that mean exactly?
  WLan is listed in Device Manager?
  And if SO, have you tried reinstalling the WLan driver again?

  If you tried that, do it!
  Uninstall the Wlan driver (in Device Manager), download the latest driver WLan driver Toshiba page, install the driver, reboot the laptop and try to set up the connection.

• Satellite L300-17N (PSLBCE) - wireless card does not work

  Hello

  I recently bought a Toshiba Satellite L300 (PSLBCE) that came without any operating system and the dirvers. I installed WXP PRO SP2 above and downloaded all the drivers from the Toshiba site. Everything has been installed ok and functional except for the WLAN card. The wireless network card, it is a Realtek RTL8187B but it is not recognized by my laptop: if I Check Device Manager it does not appear (it does appear that "Network controller" with yellow mark). Then I went to Realtek website and download new drivers from there and installed again... also with these dirvers WLAN card still not recognized.

  No idea this coud be the problem? I don't know that I have downloaded the correct dirvers from Toshiba Web site as well as the Realtek site... but none of them helped. The chipset drivers have also been installed and also the last BIOS version (my BIOS version is newer than the one on the site of toshiba with the drivers for this model)
  May this be a conflict with the other dirvers or WXP PRO SP2?

  Thank you

  Hey Buddy

  Satellite L300-17N does not support Realtek RTL8187B but Intel 11 a/b/g (13ch) - Golan Wlan card.

  I recommend to visit the portal of Toshiba Europe WLan and recommend to download and install the driver Intel WLan from here:
  http://APS2.toshiba-tro.de/WLAN/?page=downloads

  Here, you can try the Intel PRO/Wireless 3945/4965/5100/5300 driver package!

  I would appreciate your comments

• Atheros AR9285 802.11 wireless card does not work.

  Wireless for my laptop HP that atheros AR9285 recently stopped detecting my router while I have my Netgear G54 WGR614v10 encryption card any type of security, I chose, but it detects my router if I switch off my encryption.

  I read a post from Paul_Tikkanen Atheros WLAN Driver corrects connection issues with many new routers (Linksys, Netgear, D-Link, etc.), I downloaded the driver and installed it but it has not made a difference.

  I also watched to make sure that bluetooth was not on, I read somewhere that it might interfere with my wireless card, but it was not on.

  Any help would be greatly appreciated!  Thank you

  Windows 7

  OK, this is strange, and then we will have to check each setting security on your router and your network card to make sure they match. Access your routers webpage bios and go to network security, if possible on your PC to cable and take note of the security settings and compare them with the security of network adapter settings.
  
  ~ Bios of router ~
  * Usually, which would be the mode key staff/Enterprise wpa or wep.
  * Then check that your type of encryption on the router security example would be AES or TKIP.
  * And then check your 802.11 mode.
  
  ~ NIC ~.
  * go to start button or charms right mouse click Select Network option and click. * highlight of the WiFi adapter which is having right mouse questions click.
  * then choose status to the next screen, click Properties wireless.
  * then select Security tab, try this on your laptop which works as well to make sure everything fits.
  
  Something must have went wrong with the installation of the driver. I think you need to remove or back the driver, restart your laptop and let windows update or HP support assistant app find the right driver for you if it does not.

• Satellite Pro 4600 Wireless card does not work with WIN2K?

  I have a Satellite Pro 4600 with UK dealer PA3070U-1MPC wireless operating with Windows 2000 card

  The wireless client Manager detects the network from my wireless router and the signal is excellent and I see all the Green swhowing bars.

  But I can't mske a connection in 'connections' wireless says "network cable is disconnected.

  the router works well with other laptops in my house.

  I have the latest version of Win2K also downloaded and installed the latest versions of client manager and WLAN driver for win2k to the toshiba Web site.

  'Support of toshiba in Turkey' told me ' I need another driver for Win2K for my driver wireless card cause win2K on the toshiba site isn't for "thie" wireless card ". I have been waiting for this for 3 weeks now and couldn't join the UK level 3 elusive support who supposed to have this driver. I saw on the internet is the same wireless card was sold as an accessory "made by toshiba" and he said that it is compatible with Wim2K

  What I then please? It works with Win2K, is it "another driver" and so on?

  Thank you

  Hello

  I don t think that there is something wrong with the driver because you can receive signals from router (green bars). If the driver WLan would be a mistake if wouldn t receive all signals.
  Please check device manager. If the wireless card is recognized if you are using the correct driver and the driver has been installed correctly.
  Please see this page:
  http://209.167.114.38/support/TechSupport/TSBs/all/-TSB000705.htm

  In my view, the message "network cable is disconnected" appears because your (NOT wireless) LAN cable is not connected. This post has nothing to do with the question of Wlan.
  You should check your WLan settings again.

• Satellite Pro L300 - wireless card does not work under Ubuntu

  Hi all,

  I want to know what is the model of my wireless card. I need to know because I need the driver of windows for Ubuntu. I see on the internet for the L300 series, we have a lot of wireless card... I want to know what is the card of my pc.

  Thanks a lot and best regards

  LOL: D you're funny type. Please don t do it harder they are.

  There are many opportunities to find out what card WLan has been inserted.

  The easiest way is to check the bottom of the unit.
  There are a lot of different labels and on one of the labels you should see a WLan card model or part number.
  Take this number it in the google search and google for this field.

• New blackBerry Smartphones SIM card does not let me sign

  Hi, I have a new SIM card after having lost a previous phone. I put it in another handset, one that I've used a few years ago. I am trying to open a session and put in my Blackberry user ID and my password, but it says it's a mistake. Then I went online and tried and I sign in no problem. Then, I changed my password and tried again but no luck! Can you help me? Thank you

  Jenny7733 wrote:
  Hi, I have a new SIM card after having lost a previous phone. I put it in another handset, one that I've used a few years ago. I am trying to open a session and put in my Blackberry user ID and my password, but it says it's a mistake. Then I went online and tried and I sign in no problem. Then, I changed my password and tried again but no luck! Can you help me? Thank you

  Hi @Jenny7733! Welcome to the community of BlackBerry Support Forums!

  You will need to perform an erasure of security on the device first before you can connect with a new BlackBerry ID credentials Please see: How to delete all data and applications from the smart phone BlackBerry with the optio security wipe...

  Don't forget to make a backup because it will erase all your data. Good luck!

• Wireless adapter does not

  recently restored my HP Pavilion DV6-6C35DX, and now the wireless card does not work

  It appears in the device as Realtek PCIe GBE Family Controller Manager

  the hardware id is PCI/VEN_10EC & DEV_8168 & SUBSYS_1805103C & REV_06

  I tried to search for the drivers but can't seem to find a

  any help would be greatly appreciated

  Thanks in advance

  not 100% sure how mark as resolved, but in the meantime eventually, fortunately the pilot

  Thanks for all of you who have seen this, but as I'm sure someone would have helped me

• Unable to connect to the network and wireless interface does not appear in ipconfig/all on Vista32

  My niece has a laptop of HP under vista32 who cannot access the network wirelessly or wired.  She is in College and needs the laptop on the network as soon as possible for his class work.  I tried to reload the driver wireless driver (Atheros AR5007 b/g) and reset the tcp/ip stack using the command netsh addressed in the microsoft article, but nothing works.

  I brought the laptop to work where we have an unsecured wireless lan (called comments) for visitors and the laptop can go out and find all points of access wireless including comments.  When I select the comments and try to connect it times out and tells me to watch driver and tcp/ip connections.

  Another clue may be that the wireless card does not appear when I type ' ipconfig/all', or the adapter wireless and wired adapters are not displayed:

  C:\Users\Admin>ipconfig/all

  Windows IP configuration

  Name of the host...: Hannah-PC
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  Bluetooth network connection Ethernet card:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Device Bluetooth (personal area network)
  Physical address.... : 00-21-86-39-EE-22
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  C:\Users\Admin >

  I'd appreciate any help I can get.

  Thank you!

  In the case where somone has this same question, I wanted to post my final resolution of the problem. I backed up its data and restored the laptop to factory default using HP restore and now everything works fine.  Better I would say loading Zone Alarm on Vista was a bad thing for my niece to do.  Would have been nice to find a magical solution to avoid restoring but never found one.  Even after the alarm zone using their instructions by removing completely, there was apparently a problem with the registry who wouldn't let networks are working properly.  One thing I noticed after that the restoration was the HP Wireless Assistant poped up and told me about available networks, etc.  Assistant wireless didn't pop-up at all whne the cell was dismantled so maybe assistant was broken?  Well, I'm out...

• Wireless network card does not appear in the Device Manager on Satellite L50 - B - 1 DM

  Hello!
  I bought just new Satellite L50 - B - 1 DM, model number PSKTCE and installed on Windows 7 Professional SP1 64 bit. He came without OS installed and without driver installation disk.
  Problem is that Wlan card does not appear in Device Manager.

  For my Toshiba support model are 37 drivers and programs. I have already installed: Windows 7 Professional 64-bit, all updates to Windows that appeared, SP 1, driver LAN, Toshiba Value added Package. And I tried to install all wlan drivers 4 in the list of "tool utility Intel ' also.
  Does not always display any connection without wireless WLAN card. Pressing Fn + F12 does not change. In "Network connections" is the only connection - LAN. No WLAN, no bluetooth.

  I have "Other devices" in Device Manager with yellow marks on: network controller; PCI device; PCI Simple Communication controller; SM Bus controller. USB controller; Unknown device (with Microsoft ACPI - compliant system location) and video controller.

  Any help would be welcome. Thanks in advance

  If it's not bad - just saw that my BIOS is version 1.70

• Why Apple cards does not work in Saudi Arabia?

  Why Apple cards does not work in Saudi Arabia?

  Hi msmadi,

  I understand you are trying to use cards for Apple in Saudi Arabia, but faced problems. I don't know what questions you are running, but if you want to use a specific feature, it may not be available here. Take a look at the link below to review what features are available with an iOS device using iOS 9.

  iOS 9 feature availability
  http://www.Apple.com/iOS/feature-availability/

  Nice day

• Satellite L100: Wireless network card does not recognize media

  I bought a Wifi (Gigabyte gn-wi01gs) to my L100, but this card does not work. I installed all the drivers, but it does not recognize any network. No other computer has a problem.

  This shows that, when I press Fn + F8 "wireless communication is disabled. Please activate the wireless communication switch "." What 'switch '? There is no switch!
  What should I do?

  Someone mentioned here in the forum that with the version of the BIOS under 2.10, the Wireless LAN card is unable to get a correct IP address of the connected Access Point or it is impossible to get a connection point of access to all.
  Added the new BIOS that fixed a problem with the wireless LAN switch kill, the switch did not work properly.
  WLAN should be activated by pressing FN + F8.

  So please update the BIOS to Version 2.10 or higher, but don't forget to use the good BIOS and the correct procedure of updating the BIOS!
  Incorrect BIOS may damage the motherboard.

• Interruption due to the light wireless wireless connection does not illuminate

  I have a 4330 s HP's Probook

  I can't connect wireless in reason, wireless led light does not activate, I don't know if I need a driver, but I guess that all drivers are real.

  hope someone can support me in this case.

  Thanks in advance for your support

  Original title: wireless connection

  Hello Ruka,

  Thanks for choosing the Microsoft forums.

  I understand that you can not connect to the internet using the Wi - Fi connection on the computer.

  I would like to know some information about the problem so that we can help you further.

  You did it all change hardware or software before this problem?

  Try the following and see if they work for you.

  Make sure the wireless, as the function key switch for the wireless is turned on. Please refer to the user manual that came with the computer.

  Method 1.

  Try to use the network for Windows 7 troubleshooting:

  http://Windows.Microsoft.com/en-AU/Windows7/using-the-network-troubleshooter-in-Windows-7

  Method 2.

  Please try to look in the Device Manager for any exclamation point in Device Manager.

  Check the network card

  1. click the Start button picture of the Start button, type "device manager" in the search box and then in the list of results, click on Device Manager. Need administrator permission if you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  2 expand adapter option and then check for any point of exclamation.

  Is there an exclamation point on found network adapter, then we troubleshoot the missing or corrupt wireless drivers. And we must also update the latest driver wireless from the manufacturer's Web site.

  To install the latest drivers for network adapter from the computer manufacturer Web site:

  http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdHome/?javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken&javax.portlet.prp_bd9b6997fbc7fc515f4cf4626f5c8d01=wsrp-navigationalState%3DswEnvOID%253D4059%257CswLang%253D%257Caction%253DlistDriver&javax.portlet.tpst=bd9b6997fbc7fc515f4cf4626f5c8d01&sp4ts.oid=5045451&ac.admitted=1393314132234.876444892.492883150#Driver

  Method 3

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win81tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Method 4.

  Why can't I find a wireless network?

  http://Windows.Microsoft.com/en-us/Windows/cant-find-wireless-network#1TC=Windows-7

  Additional information:

  Why can't I connect to the Internet?

  http://Windows.Microsoft.com/en-in/Windows/cant-connect-Internet#1TC=Windows-7

  Wireless network card: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows/wireless-networking-FAQ#1TC=Windows-7

  Wireless light does not illuminate

  http://h30434.www3.HP.com/T5/wireless-Internet-home-networking/wireless-light-does-not-turn-on/TD-p/894811

  Hope this information is helpful and let us know if you need more assistance. We will be happy to help you.

  Thank you.

• P20-552: 2 GB SD card does not work.

  I have a P20-552 (PSP26E-025E9-S4), which is about 18 months old. I recently bought a digital camera (IxUS 750) barrel with a 2 GB Sandisk Ultra II SD card and the combination does not work well. Although I can transfer images from the camera to my Toshiba laptop with a USB cable, sometimes, I would use the SD slot on the laptop, but there seems to be a problem: seconds after pressing home the SD card in the slot, I get the message "disk is not formatted - do you want to format it now?". I said OK but then I get the message "cannot be formatted disk in drive E".

  The card continues to work perfectly fine in my camera and on my iPaq Pocket PC. In the Toshiba SD card works quite happy with Sandisk card of 256 MB SD, which is usually in my PDA.

  Anyone has an idea why the 2 GB card does not work in the Toshiba? It's updating a driver - I watch the other day but I couldn't find anything that seemed appropriate, but I might well have forgotten something...

  I'm running XP Home Edition (SP2) and are automatic updates IT. I have Norton Virus and Zone Alarm running and have no problems with other software/applications - at least, no problem, as someone suggested to suck my laptop overheating a few weeks ago ;-)

  Thank you, Brian.

  It seems that the unit doesn t support this card.
  See your user manual. You will find an information that this device supports only the following SD card formats: Mo 8/16/32/64/128/256 and 512

  According to this document, the 2 GB are high.