Windows 7 on ASUS PC - connectivity with router wireless

Similar Questions

• When I try to connect with my wireless laptop will connect only to Local access. If I connect the laptop to the router with the ethernet cable, it works very well.

  VIsta - Local access only

  HI -.
  I recently moved.   I use the same router from my old apartment and I had no problem connection in the past.   Since I moved I have a new Time Warner modem (Cisco) and the modem works fine.

  The router also works very well I'm able to connect with my iPhone and IPad without any problem.

  But when I try to connect with my wireless laptop, it will only connect to Local access.    If I connect the laptop to the router with the ethernet cable, it works very well.

  It's a Dell Studio 15 with Vista.

  The computer is able to connect to wifi to other places without any problem, but for some reason that I can't connect home.   I tried to reset the modem and the router several times, but that did not help.   I tried the option repair & diagnose several times but it doesn't work.

  I tried to look for other solutions online and tried to disable IPv6, and while it helped some and I was able to connect wireless, the computer ran so slowly that it didn't seem like a good solution.

  This has been very frustrating.   Thanks in advance for any help or suggestion.
  Staci

  Hello Staciusa,

  Have you tried to change the wireless channel that your router is running at? There may be interference that could prevent the internet connection:

  Take a look at step 6 in this article that give more details about it:

  http://www.Microsoft.com/athome/Setup/wirelesstips.aspx

  If you need assistance to change the settings of the specific router, you will need to contact your router manufacturer or your internet service provider.

• How to share files and printers between windows xp desktop that is connected to a wireless router with a laptop running windows 7. printer is connected to the desktop computer

  Hi all.  I normally wouldn't have a problem with that, but I must be missing something.  I want to create a home network or small business between my desktop running windows xp pro sp3 and my laptop running windows 7 Home premium.  I want to share files and printers.  My desktop with windows xp computer is connected to a wireless router.  The printer is connected to my desktop as well.  My laptop is wireless with the wireless router.  I tried everything I can think of to get these two devices to the network.  If anyone can help.  Don't forget, my printer is connected to my desktop with windows xp and is connected to my wireless router which is connected to my cable modem.  Internet works fine.  the laptop with windows 7's wireless and internet works fine.  just impossible to get the two see each other or share what anyone.  Thank you.

  With respect to the sharing of printer (s), microsoft has a utility called 'Print Migrator'

  Download & install, create copy, send a copy to the other pc to share its use.

• Unable to connect with router wifi - Satellite L555-110

  Hello

  I use the following configuration:

  Satellite L555-110
  Modell Nr.: PSLW8E-01E00NGR
  Windows 7 64 bit Home Premium (with all updates)

  I bought this Book 3 weeks ago.

  My laptop won't connect to my WiFi router. I use the drivers provided by Windows Update.
  I also tested the following Realtek drivers:

  RTL8191_8192_SE_WindowsDriver_2007.1.1002.2009.F00 62.P0525_ISS_1.00.0130.L

  The connection still does not work.

  I always think that there must be a driver problem, because with another book, the wireless connection works fine.
  I can't find any solution, it's the readers makes me crazy.

  Is there advice, or is this still the problem of driver windows 7?

  Thanks for your help

  nofact

  Each laptop comes with preinstalled OS. You can use 32 or 64 bit OS (recovery Toshiba original image). Recovery image contains Toshiba driver WLAN tested and functional.

  So my question is: have you noticed some WIFI problems with this original configuration of Toshiba or later after Windows update?
  Please check all of the updates before installing them and do not allow drivers to update.

• Re: office jet pro 8600 connect with router but not recognized on the network

  BUT... it did NOT work for me.

  I have the same situation:

  1. I bought and installed e-8600 HP OfficeJet Pro on my Linksys wireless network, while it was usable by anyone with connectivity to my wireless network.  It is installed without problem.

  2. I need to reconfigure and move my Pro e-8600 to my Linksys Wireless to my network routers NETGEAR AC1450 wireless, so I removed the printer and uninstalled all the software Pro e-8600 my laptop ACER running 7/Windows-b4bit.  I have restored the default settings on my Pro e-8600, reconnected to my network NETGEAR Wireless and restarted all power of the State.

  3. when I downloaded the latest driver for the Pro e-8600 to hp.com and tried to reinstall the e-8600 Pro on my NETGEAR network, the installation software couldn't recognize the e-8600 Pro on my NETGEAR network.  During the process, the software recognized the network, but the printer is not found.

  Help!

  Hello-

  Have you checked your router settings?

  Although the wizard detects the printer and you can reach the built-in Web server, the printer is not communicating with the router effectively.

• connect with the windows computer using usb after connecting to the wireless mac

  Printer HP Photosmart 7520 connected wireless to the new iMac using Fios router wireless.

  Can I connect the printer even to an old Windows computer (running XP) via USB without interfering with the connection Wireless for Mac?

  Hi Rekjek,

  On both wireless and USB is allowed. There should not be all the problems between the Mac and the PC using the same printer.

• Windows 7 problem of bluetooth connectivity with bluetooth for Skype-ing headsets?

  I've read similar questions on the form, and unfortunately I could not find an answer to my question. Starting from 01/12/09, I upgraded to windows 7 home edition with minor compatibility issues (negligible). But, before installing windows 7 I was able to use my headset bluetooth with Skype. Now, sype does not recognize this connection between pc and my bluetooth headset. Ironically enough my pc has allowed for the configuration of my listener. my headset is appointed to be my helmet without wireless/bluetooth for use with Skype or any other program from my PC. In addition, my PC is allowing and acknowledging the connectivity between my PC and the bluetooth headset but not Skype. I tried to reconfigure Skype, but have failed to prove any changes to the default settings. your help is greatly appreciated.

  Windows Update has nothing to do with the upgrade of Windows or your problem. Contact the Skype Support or try to repost your question here: http://social.answers.microsoft.com/Forums/en-US/w7install/threads

  PS: Is Skype in Win7/IE8 still supported? ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Error Windows update "0x8024402F" after you connect with domain name

  Working Group to update windows. But the same working group is impossible to get the update when connecting with the field. The two cases, we use our local DNS server address. No problem with most of the windows 7/2008 R2. Customers Windows XP are not up-to-date.

  Hey Anto Singh,

  The question you have posted is better suited in the TechNet forums. Please see the following link for more information.

  Windows XP IT Pro category

• Office jet pro 8600 connect with router but not recognized on the network

  I just installed new router e1200 lonksys. JO HP 8600 pro connects with the router, but the printer cannot see 8600. IP 169.254.223.37 on said install ip is the placeholder and printer not connected. have restarted once 1000 and tried to reconnect. New router has OMP and thrust of 3 seconds the button on the router. Also failed to connect on the router definition reviews

  8600 worked fine on the old router. Problem started when I connected the router after that cable modem connected then modem vonage. Previous setting was cable - vonanage and wireless router - all worked well then.

  Also downloaded 8600 new complete software after losing the Wi - Fi connection - please help!

  If the Ethernet cable is plugged into the printer, it will disable the wireless radio.

  If this is not the case in the network menu, network by default.  Then, in the same network menu, run the Wireless Setup Wizard.

  If this does not work, we will come on your new router a bit.

• Troubleshoot the bad connection with router (WRT350N) and Point (WAP4400N) wireless access

  Hi all

  I have a problem and will apprecaite all the help I can get. I think I will find an answer here.

  I have a small network, Linksys WRT350N (wireless router) attached to a modem and then connected to a desktop computer and with 3 wireless laptops connected to the router. All 3 are really great to work and access the internet very well.

  Currently, I have the need to expand the network to 3 floors, so I bought 3 Points of access wireless of Linksys (WAP4400N).

  I ran 3 cables CAT5e cable from the router and which ends individually all 3 floors, the top floor is less than the router 40meters. With the cables that came in their boxes, I connected the APs to the router and I have correctly set up the 3 Access Points with them attached to the router, all 3 works perfectly (I can access wireless internet via 3-point). However when I take the points of access to the upper floors and connect cables cat5e APs no longer work but connect after some time with the message "limited connectivity".

  Why can I connect when the APs are connected to the ground floor via a short cable that came in the box and not when it is connected to put cables from the ground floor to the upper floors but rather make the "LIMITED SERVICE" message and cannot connect to the internet.

  Also if I connect the cat5e cables directly to a laptop computer on all the floors, I can connect to the internet (the work of cables fine when connected directly to a laptop computer), but when it is connected to the connection of the APs has failed and I begin to see strange IP addresses from the APs.

  Oh, one more piece of important information: when I connect cables CAT5e cable on all floors direct to a laptop I can connect to the internet (the work of cables very well when it is connected directly to a laptop) but when connected to the failed to connect APs and I begin to see strange IP addresses from the APs.

  HEPL!

  I think I have the forum a status report on my post. As I mentioned in my last post, the problem has been as a result of lower cable at my provider. The network is running smoothly. Has been in place since last week when I replaced the lower quality cat5e cable cat5e cable.

  A Board here please be careful and make sure you complete the cable. A bad end can lead to connection problems I discovered in this case when my team confidence terminated cable incorrectly.

  Network up to & operational: Linksys WRT350N router without wire + 3 Linksys Wireless Access Points WAP4400N + Modem providing access to (1 computer (cable), 6 workstations (wireless), & 5 laptops (wireless).) Network to grow shortly.

  Thanks to everyone who helped make this project a reality.

• Windows 98 is able to connect to a wireless connection?

  Wireless router for Windows 98 Machines

  I have an old Windows 98 machine and want to connect to my wireless router Lybnksys with a lan cable to upgrade the computer via the internet/downloads.  How can I communicate with the router for Windows 98?

  Hello JanOtterson,

  Support for Windows 98 ended.

  For reference:
  http://support.Microsoft.com/ph/1139

  For Windows 98 compatibility, you should check the specs on the hardware and the software bundled with it. Windows 98 is not compatible wireless zero configuration, so you will need some type of software installed, in order to implement the wireless adapter.

  Please check the links below for features and the compatibality for Windows 7 because it is the most recent and supports wireless connectivity.
  http://Windows.Microsoft.com/en-us/Windows7/products/features

  For Windows 7 configuration required:
  http://Windows.Microsoft.com/en-us/Windows7/products/system-requirements

  Windows 7 Upgrade Advisor:
  http://www.Microsoft.com/download/en/details.aspx?ID=20

  To buy Windows 7 please click the link below:

  http://www.Microsoft.com/Windows/buy/default.aspx

  Hope the helps of information.

  Kind regards.

• HP Pavilion Notebook 15-p119: Windows 10: since the execution of Windows update, I can't connect to the wireless network

  Hello, HP assistance.

  I'm having a problem with the connection to my home Wi - Fi network. I am sure the problem has nothing to do with my material and is a problem of Windows only.

  Here's the story: I was fortunately with the Internet from the network before and Windows was connecting automatically every time. But since the Windows Update recently it does not connect. Sometimes it says "unable to connect to this network" and then sometimes it comes up with a box asking me to enter a user name and a password. The thing is... I've never set up a password in Windows for Internet access, so I do not know why he was asking me now. I looked around the Internet via my Tablet (which is connected to the same Wi - Fi network fine, with my phone) and found that it is a common problem. And yet, none of the solutions work for me.

  I wonder if the solution is somehow change the settings so that a password is not required to connect to a network. Or maybe enter a default user name and password when the box appears again. That said, the box did not come for a while.

  Help, please!

  Thank you for your query.

  I understand that your mobile phone works well and you didn't have any problems with your wireless connection. After the upgrade to Windows 10, your wireless network is intermittent and will prompt you for a user name and password.

  The guest is not the Internet, but rather to join your network. He is looking for the network name and password.

  When I did a search for HP laptop 15-p119, I was unable to locate this model. Would you please check your model? How can I find my model number or product number?

  After the upgrade to Windows 10 did you all your Windows updates?

  Sometimes it fails to be installed automatically, if you can try running the Troubleshooting of windows update. to maybe gain others.

  You run the HP Support Assistant since the upgrade?

  If the problem persists, once you have established a test of Wi - Fi automatically update drivers Device Manager wireless.

  • Right click on the Windows button in the bottom left corner, then choose Device Manager

  • Click network to expand the list

  • Right click on the wireless adapter and choose put updated driver

  Select "Automatically search for updated driver software" this month may start a download to install a newer driver.

  Here is a link that can also help. HP PC - troubleshooting wireless network and Internet (Windows 10) 

  Thank you for your participation in the Forums of HP! We want to help you as well as others who may encounter a similar problem as yourself. Please consider tagging the post in order to resolve your problem as " ""Accept as Solution"" " to help other members of the community!

  "To show recognition for my efforts, please click on the" ","inch Up Icon " below.

• After a clean install of Windows 7, I can't connect to the wireless network and more problems...

  I recently did a clean install of genuine copy of Windows 7 Home Premium to clear unwanted programs all on my computer. Because the product key are disabled unexpectedly.

  The installation works fine, but after the installation. I can't connect to a wireless network, because there is no network adapter installed on the computer.

  Also, I can't set my screen resolution of 1366 x 768. Before any new install, the screen resolution sets to 1366 x 768 as native and recommended screen resolution. Now, I'm stuck at the screen resolution 1024 x 768. I need to change the graphics card so my laptop screen can support 1366 x 768? If necessary, please give me instructions on how to do this.

  Thank you.

  Acer Aspire one C5Cbb-722

  Go here, select your model, then download and install the network and video drivers.

  http://www.Acer.ca/AC/en/CA/content/drivers

• Connectivity with B210A wireless problem

  I have a B210A and I am having some problems trying to get my PC or laptop to connect to the wireless printer.

  Both have been implemented before wireless and now wants to connect.

  My PC is Windows 7 64 bit and the laptop is Windows 7 32-bit.

  The wireless network test report shows no problem, but when I try to connect using the installer of HP, the printer is not found. Even when you are asked to enter the IP address manually on the installation, the printer is not found.

  Someone at - it ideas about what I can do to fix this?

  Disable AVG completely and try again.  At AVG in place and active when you installed the HP software (it should have been for the installer can configure).

• Windows 7 workstation loses the connection with the Server 2008 "

  Server running Microsoft SBS 2008 Standard.  Second location is the use of Remote Desktop.  These workstations are very good.  Only the workstation in the same place loses the connection periodically.  Workstation can reconnect, but never know when it will drop.  The user has to go to the remote location to know that the work will not be interrupted.

  This particular configuration has worked very well for a few months.  Long story short about 2 weeks after main tech (which has implemented) is deceased in August 2010, there was a major issue.  No one is really sure of what it is, but everything is back up and running just now lovely annoying drop except for this connection.

  I'm scheduled to go on Tuesday.  This is a seasonal business and people we're patient but kind of necessity to deal with this finally.  I am pretty well convinced that this is not the Peachtree program causing the problem.  However, the error indicates that Peachtree is not installed on the server, and yet it is, obviously.  That is why we believe that the connection has been interrupted.

  All this makes sense?  Someone knows the effects of any automatic updates of end of August 2010, which may have caused a situation like this?  I know that currently they don't dare to update Java or something does not work well.  Thought, that you may know of something that happened at that time that could cause this.

  Hello

  Your question of Windows 7 is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the Windows Server Forums on TechNet. Please post your question in the Windows Server Forums.

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer/