Windows 7 - "unable to connect to the network {SSID}.

Similar Questions

• Satellite L40: Windows Vista unable to connect to the network

  My Satellite L40 laptop was connecting to my network wireless perfectly since Christmas. But two days ago, it stopped! I can see the networks available on the laptop but when I try to connect I get the message "Windows cannot connect to the network. Following the link to "Diagnose the problem" has no useful effect.
  I installed Windows Vista Service Pack 1 yesterday to try to solve the problem, but always without success.

  Any advice would be appreciated.

  Select this option.

  Hello

  Please go to the drivers Toshiba download page and download the latest Wlan driver for your wireless card installed, then remove the old driver and install a new one. It should work.

  Otherwise, you should try to recover your entire system and replace the drivers installed by some more recent...

  Welcome them

• No network adapter driver is available after reinstalling Windows Vista installation disk... Unable to connect to the network

  No network adapter driver is available after reinstalling Windows Vista installation disk... Unable to connect to the network

  Hello

  Know what type of network card you have and download the drivers of its supplier.

  It doesn't matter what it is always a good idea before re-install/upgrade to log on to the computer support page, download independent drivers from there and put them on a flash drive.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Unable to connect to the network "\\localmachine\sharedname" share

  I use VMware vCenter Converter Standalone client, v5.0.0 build-470252, running on a 64-bit Windows 7 computer, try to import a Windows 2008 computer virtual (hosted by VMWare infrastructure) on my local machine.

  At the start of the converter, I have "connecting to a local server.

  Specification of the source system is OK, even if I don't know the certificate error.  The conversion wizard installs his agent and it connects OK.

  To the Destination System, I said:

  
  Type of destination: VMware Workstation or other virtual machines to VMware
  Product VMware: VMware Workstation 8.0.x
  Information on the virtual machine:
  Name: same as the source system, such as detected by the converter
  Location for the virtual machine: \\localmachine\sharedfoldername
  Username and password: my Windows 7 credentials, with full control over \\localmachine\sharedfoldername, the action and the underlying folder.

  "When the converter checks the destination settings, it is reported: unable to connect to the network"\\localmachine\sharedfoldername"share

  So far the measures of investigation:
  -Connection to the share through Windows Explorer works fine; It is possible to write to the share

  -J' tried specifying the share as '\\localhost\sharedfoldername', but get "the share specified network 'localhost\sharedfoldername' does not exist."  It was a bit of a long shot, I guess, but the form does not work in Windows Explorer.

  -Have you tried with the file and print sharing both power - on and off seemed worth a try after looking at other posts on this forum

  The help says 'If you are connected to a local Converter Standalone Server, providing a network path or a local path to the destination directory'.  I tried the local path "C:\Virtual Machines\sharedfoldername", but got the message "error: specified as a (local) drive Destination.»  "Please specify a UNC path such as: \\machine\sharename.

  Aid also States "You have not to provide user credentials if the location is on the local storage of the machine where Converter Standalone server running."  However, the next button is always disabled until credentials are provided.

  Can anyone help please?

  You must be able to access the \\localmachine\sharedname of the * SOURCE * machine. The job of conversions P2V of Windows is to install an agent on the source, then the agent connects to the target (this is why it must be on a network share) and transfers the data. You can browse \\localmachine\sharedname of the source (but not where the converter is installed)?

• Failed to open the first Pro CC 2015.Windows are unable to connect to the Adobe server... This application failed to start properly 0xc000001d... Click ok to close the application

  Failed to open the first Pro CC 2015.Windows are unable to connect to the Adobe server... This application failed to start properly 0xc000001d... Click ok to close the application

  Hi qksdjhfb,

  For a fix, update for first Pro CC 2015 (9.2).

  Thank you

  Kevin

• Error message: "unable to connect to a windows service windows could not connect to the system event." Unable to connect to the network, Windows Vista Home Edition

  Hello

  When I start my laptop there is a long pause between the home screen and the cover page of my office where the message "unable to connect to a windows service windows has no can connect to the system event. I am unable to connect to networks as says "the dependecy service or group could start. I checked some of the solutions to this problem, including the execution of the 'netsh reset winstock' program that did not work. Any advice would be very helpful. Thank you.

  Hello

  It would be a good idea to run the System File Checker tool to see if you have corrupted files

  "How to use the System File Checker tool to fix the files on system missing or corrupted on Windows Vista or Windows 7"

  http://support.Microsoft.com/kb/929833

  Use the (SFC.exe) System File Checker tool to determine which file is causing the problem and then replace the file. To do this, follow these steps:

  1. Open an elevated command prompt. To do this, click Start, click principally made programs, Accessories, right-click guest, and then click run as administrator. If you are prompted for an administrator password or a confirmation, type the password, or click allow.
  2. Type the following command and press ENTER:
     sfc/scannow

     The sfc/scannow command analyzes all protected system files and replaces incorrect versions with appropriate Microsoft versions.

  ___________________________________________________

  And Malware scan:

  Search for malware, if necessary using the safe mode with networking.

  http://www.bleepingcomputer.com/tutorials/how-to-start-Windows-in-safe-mode/#Vista

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap the F8 key repeatedly until you are presented with the Boot Options Advanced Windows Vista.
  3. Select the Safe Mode with networking with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  Then, download, install, update and scan your system with the free version of Malwarebytes AntiMalware in Mode safe mode with networking:

  http://www.Malwarebytes.org/products/malwarebytes_free

  See you soon.

• Unable to connect to the network - Windows 7 on Windows Server 2003

  original title: Six Windows 7 computers running on a network (Server Windows 2003 R2 Standard Ed) would not connect to the network in the morning, startup repair is unable to repair

  We have 10 PC running Windows 7 on a network (Server Windows 2003 R2 Standard Ed) and 6 of them started up the Start Up Repair screen the same morning. Run startup repair but then received the message "Startup Repair cannot repair.

  Windows could not start. A recent change in hardware or software may be the cause. Startup Repair cannot repair.

  Details of the problem: event name offline Startup Repair

  Signature 01 6.1.76.00.16385

  02 6.1.76.00.16385

  unknown 03

  04 21200896

  AutoFailover 05

  2 06

  07 0x6b

  OS version 6.17600.2.0.0.256.1

  Locale 1033 ID

  In the details to diagnose & repair was the only entry that indicates a problem

  First cause is parameters 6 unknown error checking b 0 x 0, 0x0, 0x0, 0x0

  In all cases the system restore worked but had to come back a week, him the day before restore point would not work.  In one case, the problem is that system restore and the next day does not, eventually reinstall.

  Clues or tips as to what has caused this?

  Kind regards

  GinSeek

  http://TechNet.Microsoft.com/en-us/WindowsServer/default.aspx

  http://social.technet.Microsoft.com/forums/en-us/winservergen/threads/

  Above links are for server communities.

  For any question on Windows 7:

  http://social.answers.Microsoft.com/forums/en-us/category/Windows7

  Link above is Windows 7 Forum for questions on Windows 7.

  Windows 7 questions should be directed to / stationed there.

  You are in the Vista Forums.

  See you soon.

  Mick Murphy - Microsoft partner

• HP ENVY 15-k163cl: HP ENVY 15 updated to Windows 10, now unable to connect to the network

  I've recently updated to Windows 10 with my laptop (from Windows 8) and remember, Windows 8 was working fine but now that I've updated for Windows 10, I can't connect to my home network.
  
  When I turn on my laptop, it is not automatically connect to my network and when I try to connect from the network settings, I get an error "Could not connect to this network" and I have to wait at least 30 minutes before it automatically logs. After waiting that it works, but my laptop goes to sleep or goes inactive for awhile, it disconnects again and I have to wait
  
  I connected via hotspot and it worked fine, but all of my other computers laptops HP connects very well and they are 10 Windows as well. Only this laptop is upward, so I guess it's a problem with a new driver.

  Hello:

  The only suggestion I can offer would be to install the latest driver for the Intel Dual Band Wireless-AC 3160 adapter - 802.11 and see if that helps any.

  The 2nd driver on the list is W10 x 64.

  https://Downloadcenter.Intel.com/download/25513/Intel-PROSet-Wireless-software-for-Windows-10

• XT720: Unable to connect to the network for upgrades

  Hello

  I recently had a new Motorola Milestone XT720. I tried to get the software updates using the "connection to phone" functionality system updates. If I connect my phone via the network or via WiFI, I get this message "the device is unable to connect to the server, please try again later"

  How can this problem be solved?

  How to get the system through files zip for Android updates?

  Kindly let me know.

  It is not uncommon to get this message when checking for OTA updates - update servers seem to be pretty random that they are actually on and accessible, or not.

  Your best bet for checking updates is to use the Motorola (MSU) software update. Search on a site of Motorola to find. It is a windows program that will check updates for your phone. More updates appear here before OTA (if they are already on OTA)

• Unable to connect to the network because the parameters of the computer do not match the requirements of the network.

  The main computer in my house is connected to the web via a modem to our ISP (Cox).  We use a Cisco's Linksys wireless router.  We have configured a new laptop to connect through the router yesterday.  Now my laptop, which had been the connection very well, can't access the network.  When I go in the "network and sharing Center" and pull up nearby wireless networks, our network shows is even more bars, just a red X.  Reads the error message "unable to connect to this network because the settings of that computer to match the parameters required network.»

  I don't know what has changed on our network, but I was unable to understand what these "required parameters" are, so I was unable to change the settings of my laptop to match the requirements.  Pls help.

  Hi Sharpdale,

  Step 1

  I first suggest you to perform network troubleshooting in Windows 7 and check if it finds problems, and if he is able to fix it.

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  Step 2

  Use Windows to configure wireless settings and check if it helps to solve the problem.

  a. click on Start menu and select run

  b. type ncpa.cpl, and then click OK to open the menu of the network connections.

  c. Select your Wi - Fi connection service and choose the option change settings of this connection.

  d. go to the wireless tab and select (tick) labeled use Windows to configure my wireless network

  I hope this helps. Let us know the results.

  Thank you and best regards,

   

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Unable to connect to the Network Time Capsule wireless

  I just changed ISP (AT & T to Time Warner) and I use my own modem cable (Arris SB6141). I connected by TC via the WAN and knitting laptop via the connection to the local network, but now only my MacBook Air (El Capitan running) connects to the wifi network of TC. Nothing else connects; AppleTV (w/Siri), iPhone 6s (9.3.1). Is there a compatibility issue that could be the cause of the problem between the modem and the TC? Or is there something I'm supposed to change with the settings? It worked fine when I was using a router 2WIRE AT & T U-Verse.

  Looks like the router Mode of the time Capsule airport is set to Off (Bridge Mode)... (which would have been correct for use with a 2Wire product)... but, it must be set to DHCP and NAT to use with a simple modem.

  Turn off the modem for at least 20 minutes... more won't hurt

  Turning off time Capsule

  Make sure the Ethernet cable from the modem connects to the "O" on the Time Capsule WAN port

  After the 20 + minute modem switch off period has finished, turn on the modem and let it run for 10 minutes

  Then, turn the time Capsule and let it run for 5 minutes

  On your MacBook Air...

  Open AirPort Utility... (Finder > Applications > utilities > AirPort Utility)

  Click on the image of the time Capsule

  Click on edit in the window that appears

  Click on the network at the top of the next window tab

  Make sure that the setting of router Mode = DHCP and NAT

  Click Update at the bottom right of the window and give the time Capsule a minute full to restart

  Recheck the network and report on your results

  Unfortunately, the SB6141 and Apple routers not always who hear well together, so keep an eye on the issues

• Dynadock U3.0 - unable to connect to the network

  I have a U3.0 Dynadock and when you try to connect to the network at work via a network cable, the parameters were not detected automatically.
  I then put manual details (IP), but this did not fix the problem.

  I assigned by DHCP the Dynadock should get a certain IP address.
  I still have a problem.

  In addition, when left on DHCP, subnet mask is 255.255.0.0 which is weird.

  Has anyone else had trouble linking their Dynadock to their network?

  I use a laptop another progress, running Windows 7, 64 bit.

  I found a solution.

  update to the latest version of the software available at toshiba for the dynadock solves this problem.

  software provided with the hardware is V6.1

  to solve the problem, it is necessary to download the toshiba support website V6.2.

  Also note, that windows 7 doesn't automatically recognize that this software update is available.

• Unable to connect to the network and network adapter is not detected

  Hello, this is the first time I use a laptop ( HP Pavilion 2332se g6 ) and I installed Windows 7 Ultimate 64 bit. I cannot connect to the network (wired or wireless) and cannot connect to Wi - Fi.

  My problem is perhaps the same problem in this post in your forum, so I provide the same information. If it's not the same problem, ask the details you need.

  What I see in device (with hardware ID) Manager:

  • Other features:

  Bluetooth controller:

  PCI\VEN_1814 & DEV_3298 & SUBSYS_18EC103C & REV_00

  PCI\VEN_1814 & DEV_3298 & SUBSYS_18EC103C

  PCI\VEN_1814 & DEV_3298 & CC_0D1100

  PCI\VEN_1814 & DEV_3298 & CC_0D11

  Ethernet controller:

  PCI\VEN_10EC & DEV_8136 & SUBSYS_183E103C & REV_O5

  PCI\VEN_10EC & DEV_8136 & SUBSYS_183E103C

  PCI\VEN_10EC & DEV_8136 & CC_020000

  PCI\VEN_10EC & DEV_8136 & CC_0200

  Network controller:

  PCI\VEN_1814 & DEV_3290 & SUBSYS_18EC103C & REV_00

  PCI\VEN_1814 & DEV_3290 & SUBSYS_18EC103C

  PCI\VEN_1814 & DEV_3290 & CC_028000

  PCI\VEN_1814 & DEV_3290 & CC_0280

  PCI device:

  PCI\VEN_10EC & DEV_5229 & SUBSYS_183E103C & REV_01

  PCI\VEN_10EC & DEV_5229 & SUBSYS_183E103C

  PCI\VEN_10EC & DEV_5229 & CC_FF0000

  PCI\VEN_10EC & DEV_5229 & CC_FF00

  PCI Simple Communication controller:

  PCI\VEN_8086 & DEV_1E3A & SUBSYS_183E103C & REV_04

  PCI\VEN_8086 & DEV_1E3A & SUBSYS_183E103C

  PCI\VEN_8086 & DEV_1E3A & CC_078000

  PCI\VEN_8086 & DEV_1E3A & CC_0780

  SM Bus controller:

  PCI\VEN_8086 & DEV_1E22 & SUBSYS_183E103C & REV_04

  PCI\VEN_8086 & DEV_1E22 & SUBSYS_183E103C

  PCI\VEN_8086 & DEV_1E22 & CC_0C0500

  PCI\VEN_8086 & DEV_1E22 & CC_0C05

  (USB) Universal Serial Bus controller:

  PCI\VEN_8086 & DEV_1E31 & SUBSYS_183E103C & REV_04

  PCI\VEN_8086 & DEV_1E31 & SUBSYS_183E103C

  PCI\VEN_8086 & DEV_1E31 & CC_0C0330

  PCI\VEN_8086 & DEV_1E31 & CC_0C03

  Unknown device:

  ACPI\HPQ0004

  * HPQ0004

  Hello:

  First install the chipset driver and reboot (will install the SM Bus controller).

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=ob-103010-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 5278311 & sw_lang=.

  Second: Install the AMD graphics driver and restart.

  For switchable graphics in your notebook, you install only the driver AMD, which installs the drivers for the AMD and Intel for the graphical configuration has your laptop. NEVER install the Intel driver only or allow updates to the Intel graphics driver to install.

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=ob-111285-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 5278311 & sw_lang=.

  Third: Install the audio driver and reboot.

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=ob-104672-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 5278311 & sw_lang=.

  Now, the rest of the devices can be installed...

  Ethernet controller:

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=ob-102604-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 5278311 & sw_lang=.

  Network controller

  http://h20565.www2.HP.com/portal/site/hpsc/template.page/public/PSI/swdDetails/?sp4ts.Oid=5229457 & spf_p.tpst = swdMain & spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_119873_1%257CswEnvOID%253D4059%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument & javax.portlet.begCacheTok = com.vignette.cachetoken & javax.portlet.endCacheTok = com.vignette.cachetoken

  Bluetooth controller

  http://h20565.www2.HP.com/portal/site/hpsc/template.page/public/PSI/swdDetails/?sp4ts.Oid=5229457 & spf_p.tpst = swdMain & spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_113004_1%257CswEnvOID%253D4059%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument & javax.portlet.begCacheTok = com.vignette.cachetoken & javax.portlet.endCacheTok = com.vignette.cachetoken

  PCI device

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=ob-102497-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 5278311 & sw_lang=.

  PCI Simple Communication controller

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=ob-102566-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 5278311 & sw_lang=.

  (USB) Universal Serial Bus controller

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=ob-102571-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 5278311 & sw_lang=.

  Unknown device

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=ob-116584-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 5278311 & sw_lang=.

• error "unable to connect to the network hidden.

  Hidden in my own home network

  I have 2 laptops. I can connect to the network wirelessly fine with 1 laptop. But the 2nd laptop says cannot connect to the hidden network. HOW CAN I VIEW IT?

  Hi WendellXD,

   
   
  1. who is the operating system installed on the computer?
  2. it worked earlier?
  3. have you made changes to your computer recently?
  4. What is the brand and model of your computer?
  5. you try to connect to the network through wired or wireless?
   
  I suggest you follow the link and check if it helps.
   
  Windows wireless and wired network connection problems

   

   

• Windows 7 Pro cannot connect to the network when idle too long (large company)

  We have approximately 75 users on Windows 7 Professional.  About two weeks ago (and the next day, Windows updates have been deployed to all PCs in our outside IT), the vast majority of users (but not all) have started to have a problem in what they can connect first thing in the morning; However, they immediately get an error that are not connected to the network, that network drives can be connected, they cannot access the internet, etc.  A reboot solves problems and the problem will not recur until the computer is left idle during the night.  Our outside IT says that what is happening on several client sites that they manage, but they have no idea of the cause; they are theorizing that it's maybe a botched Windows Update.  I have Windows 7 Pro at home and did not have the problem once.  Any suggestions appreciated.

  This issue is beyond the scope of this site and must be placed on Technet or MSDN
  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home