Windows detects the installed memory (RAM) 32.0 GB. Then there (16.0 GB usable)

Similar Questions

• Usable memory (RAM) less than the installed memory, showing remove Win7 dual-boot.

  Original title: "Memory (RAM): 12,00 GB (3.62 GB usable)", how can I resolve this issue and remove a dual boot Win7?

  I recently, after experincing problems (see below the Intel SSD), noticed the system said that there is only a 3.62 GB of Ram available in my computer.  I have this statement ' Installed Memory (RAM): 12,00 GB (3.62 GB usable) "the computer has always used a higher around 10-11 GB amount.

  I noticed that the Windows performance index was 5.6, after adding an Intell 240 GB SSD, it jumped to 7.6; However, now with the problems is 5.4, caused by the RAM.

  I ran the full memory diagnostics: start-up and verification of memory it says I have 12 GB of RAM can be used across both.  I asked with Asrock if my RAM and CPU compatible before buying it, and they said it was a wise decision for 970 Extreme4 motherboard.  I subsequently has inquired about the Kingston RAM and included information from a - Data, and they said they used Kingston ringout for approval process as with a - DATA, including the compatibility of the different types of RAM used together.  The RAM was tested and is placed on the store of the computer.
  This problem did not exist until I installed the Intel SSD.

  I don't have a problem with dual boot on my computer after installing a new 7 ultimate on the SSD, and when it worked normally, I atttached the old hd back into your computer, because important data it contains.  This caused a situation of dual-boot.  I did some research and jumped the drive as a slave thinks that it would not cause a problem.  How can I remove Windows 7 from the old hd and then remove the window dual-boot.  I tried the old way to change the startup configuration, however, I can't find it in 7 Ultimate SP1. I also sent the old HD and the start window remained, as the index and the usable Ram 3.62.

  My Questions as already said:
  How can I return to a usable 12 GB of RAM and return the highest Index of Exp Win?
  How the dual boot can be edited to boot from my SSD without window startup and remove window 7 my old HD eventually without formatting?

  The system configuration:
  Processor: AMD FX FD8300WMW8KHK 95W Vichera 3300 MHz

  Memory: ADATA DDR3 1333 AM2U139C4P2 - s 4 GB x 2
  Kingston DDR3 1333 KVR1333D3N9 / 2g x 2

  Graphics card: MSI GeForce GTX 750Ti Gaming

  Motherboard: ASRock 970 Extreme4

  Power: 600 W power supply

  HD: IntelSolid State Drive 240 GB 335 Series

  OS: Windows 7 Ultimate 64 bit SP1.

  The version of the BIOS/Date: 32 MB FRIEND UEFI BIOS legal with GUI support version 2.60

  NISH

  When you are satisfied with your problem is solved, please mark the answer. It helps others see what answered your question.

  If you posted the original question, you can mark the question as yourself have. Just click the mark as answerbutton.
  Source: http://answers.microsoft.com/en-us/page/faq#faqAskQuestion8

  You should see the response from Mark (and have found this useful Me) buttons on all messages, except your own messages, sent by others about your. They are there to allow you to tell other users, messages that you have found useful, and ultimately what solved your problem or answered your question.

• ' Installed memory (RAM): 8.00 GB (3.12 GB usable) ", what does that mean?

  Recently, I added 4 GB memory to my existing 4 GB, for a total of 8 GB of RAM.

  After installation, I checked system properties to find this info.  ' Installed memory (RAM): 8,00 go-go (3.12 useable).
  In addition, 'Windows Experience Index' before when I had a single 4 GB stick was 7.4, now after adding another stick of 4 GB, it came down to 5.9.
  Does this mean the extra 4 GB of RAM, I added is not used and is only slow down my computer?
  If yes how to do all 8 GB of usable RAM and have a higher Index Win Exp?
  The system configuration:

  Processor: AMD Phenom 2 X 4 955, 3.2 Ghz

  Memory: Corsair DDR3 (CMV4GX3M1A1333C9) 4 GB * 2

  Graphics card: Nvidia GeForce 210, 1 GB

  Motherboard: ASUS M4A78LT-M THE

  Power: iBall 350 W power supply

  OS: Windows 7 Ultimate 64-bit.

  The version of the BIOS/Date: American Megatrends Inc. 0801, 17/01/2011

  Assuming that it is memory under-score, it probably means that the memory is not fully compatible

  http://www.Corsair.com/learn_n_explore/ is a website that ensures that you get compatible memory

• Why properties system displays installed memory (RAM): 8,00 (3.47 GB usable) GB

  Why properties system displays installed memory (RAM): 8,00 (3.47 GB usable) GB
  Windows Pro 64-bit
  8 GB RAM
  1 TB harddrive
  ASUS P7H55D - M EVO motherboard
  New Windows installation has the same problem.

  Control Panel > system does not show the usable memory, only the memory installed

  The Task Manager > Performance demonstrates both installed, available and free

• Exe Explorer file process uses all the computers memory RAM

  I googled this question in many different ways and read the post until my eyes crossed. Tried several different

  ideas, checks, analyses, etc.

  This is on a Dell inspirion 3847 running Windows 7 Pro Service pack 1

  a Intel pentium CPU [email protected] Ghz, 4 GB RAM, 1 TB HD (no graphics card or any other card in pci slot)

  a brother MFC7360 n printer connected to the USB port.

  and the HD: (drive C O/S: 855 GB free of GB 909), (recovery E Drive: 17.5 GB free of 47 gb)

  The extent of the installed software is minimal, (only notable is Office 10, digital meal)

  (Digital software dining room is for the POS system), this computer is not the main computer that is running the POS system

  This computer is just linked to the actual POS in bar. (I stop this program and does not affect the)

  problem or situation that we were conducting.)

  (I can give list if necessary other software that is installed).

  And the essentially the only files on the computer (in addition to operating systems, programs, etc.) are Office, "Word files,

  Excel files.

  And a few txt, rtf, pdf, files (very small amount).

  first just noticed recently what happens, but I'm not the primary user on the computer. I checked

  and it seems that no new software or program have been recently installed or changed.  I have a little

  understanding of what the process Explorer exe is and it functions. (NOT a PRO, not a total newbie,)

  If all goes well enough to find help, and not enough to totally screw up.)

  I'll be watching this thread several times per day until solved if need more information, I'll give you...

  Here are the details of the problem:

  random computer freezes, or runs very slowly or get "out of memory" message (during the attempt

  to open any random program) and when...

  I opened the the Task Manager and in "processes" tab, it shows that there is:

  2 examples of "Explorer"exe "running... it uses a small amount of RAM (approx. 10-15 mb)(with nothing)

  Open, other than the Task Manager). Another example of "Explorer"exe "uses (starts on the same amount of)

  RAM use, without having to open anything else) it will start using more and more RAM up to uses almost all

  the available 4 gigabytes of RAM. Also during this process it uses randomly between 0 and 99% of the CPU.

  The CPU usage seems to vary (couldn't see any stable model).  the amount of RAM used begins bass

  then goes very high and the rest standing for this purpose during a random time. (then sometimes descends

  on its own within 1-5 min.). (sometimes does not lower for awhile). More details needed let me

  know, I'll check all speeds or time it takes for the situation to occur, (if necessary)

  TASK MANAGER:

  I opened the location of two Explorer exe files (both take me C/Windows"... ». (same for both

  not a system 32 file, or any other subfolder, just to 'Windows '.

  The two exe process explore "Descriptions" are listed as Windows Explorer.

  I have "Complete the process" towards the 2nd exe explore (one with high memory usage), just that process and she stops to

  a short period of time (and all works well for the time), but even once, it reappears (no exact time frame on how long until)

  Returns), (can check again and again, if necessary), to see if time is right each time to restart the process.

  If I "End process" to the 1st exe explorer (one with normal memory usage), I lose my office. (which from what

  I understand what needs to happen).

  Also get the same results if the process of "End process Tree" for the 1st and 2nd explore exe.

  Checking "properties" of two everything seems the same info. On the 'details' tab shows all of Microsoft, not

  of course, what happens if an info is important. (any info where necessary, I get and publish as needed).

  I know more and different information is no "resource monitor". but was not sure what would happen if, any info of

  It has been necessary.  If necessary you will get what that is. (let me know this as necessary).

  I've scanned any computer with 3 different anti virus (found nothing) programs

  I ran spybot search & destroy found nothing that had to do with this issue and fix some other issues that we found.

  A little info in 'Folder Options' (the 'windows folders in a separate process to launch' is NOT checked.

  and all the options are defined for the default settings (I think) (not sure if this is important)

  like I said read several messages in various forums (on similar sounding problem)... Some say spoke with

  Microsoft technical support who say 'must be the virus', others say started after the recent "windows update" and others

  say the problem of virtual memory and others say he's changed banks 'office' or the 'thumbnails previews.

  These files, and the other says "shell extensions" are the problem. (many recommended (ShellEXView), to)

  Disable all non-microsoft extensions). I was not looking for it.  My problem does not appear to be any good

  program, type file running that is causing this. It seems to happen when the computer is idle (I realize there are always some)

  process background or system running) but it doesn't have to be all open programs.

  At this point, I am open to almost any idea or suggestion.  I will continue to monitor the post until resolved and will get a

  In addition to the information required (less the credit card or account info bosses banking info HA!) (HA!)

  But seriously some help, thoughts, ideas or directions to another post with response, would be greatly appreciated.

  THANKS FOR ANY HELP!

  Hello

  Please provide detailed information about your question. I appreciate the step by step troubleshooting, and pain that you have taken to resolve your problem. However, there are a few steps more that we can try to diagnose the root cause of your problem.

  If it helps, try the methods and check them off below.

  Method 1

  As you mentioned in your message that your PC is slowing down or freezing then you can automatically diagnose and repair problems that slow down your computer by running the fixit provided in the link below.

  http://go.Microsoft.com/?linkid=9740820

  Additional information:

  For more information you can check the link below:

  8.1 Windows, Windows 8 or Windows 7 hangs or freezes

  http://support.Microsoft.com/kb/2681286

  Method 2

  If the problem persists I suggest you to try the different steps in the following Microsoft article and check if this may help. You can skip the steps that you have already tried.

  Optimize Windows performance

  http://Windows.Microsoft.com/en-us/Windows/optimize-Windows-better-performance#optimize-Windows-better-performance=Windows-7

  Important: Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.

  Running Microsoft Safety Scanner: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

  Hope this information is useful. If the problem still persists, please post back for further assistance, we will be happy to help you.

  Kind regards.

• MAX do not detect the installed PCI devices

  MAX (DAQmx 7.4.) don't detect my PCI devices installed, as if win2k has detected and installed. The NI PCI-devices are correctly listed in win2K Device Manager.

  Hello

  Please send me a report of Measurement & Automation Explorer:
  Start-> all programs-> National instruments-> Measurement & Automation Explorer.
  Then press file-> create-> Technical Support Protocol and system My->-> then then-> choose path-> next-> finish.

  Maybe the following knowledge base helps you to:
  "What is the process to remove MAX Database Corruption?": http://digital.ni.com/public.nsf/allkb/2C7480E856987FFF862573AE005AB0D9?OpenDocument

  !!! Please make a backup before removing the database of MAX:
  ' Export/Import (save) the Configuration of the measurement system and Automation Explorer (MAX)': http://digital.ni.com/public.nsf/websearch/0E0D3D7C4AA8903886256B29000C9D5A?OpenDocument

  Best regards

  SUSE

• Windows detects the USB key, but it does not appear in 'my computer '.

  When I insert the USB, windows doesn't detect the same, but the icon does not appear in 'My Computer', or anywhere else and I can't use the USB.

  The best diagnostic page on the web that I found for USB Pen Drive problems such as what you have is the following:

  <>http://www.Uwe-Sieber.de/usbtrouble_e.html >

  HTH,
  JW

• XPS 8700 does not start after the upgrade memory RAM

  Dear members of the Forum.

  I have a XPS 8700 with the following specifications:

  Core i7 4770 k

  2 TB HARD DRIVE

  16 GB of Ram (4 x 4 GB)

  NVidia GTX 660 (1.5 GB)

  BIOS version A10 (later).

  RAM sticks in my current system are all Micron Tech (here) 4 GB DDR3 SDRAM PC3 12800 240pin 1.5V 1600 MT/s.

  I had two RAM modules of tech Micron (here) 8 GB DDR3 SDRAM PC3 12800 240pin 1.5V 1600 MT/s so that I can move on to a total of 24 GB.

  After the discussion here and here, I installed the modules in slots 1 & 2 (both white) so that the system is not able to start. Not even got the bios screen. I also tried 3 & 4 configuration (both black) I ran my computer with the two 8 GB sticks only, with the same unfortunate results.

  I also saw that it is a normal problem of compatibility problems between the types of ram, but I consider that this is not the case. In addition, bad positioning of the modules is not also the case because if I put my old ram glue the computer starts normally.

  I used tape you will static isolation.

  Is the problem, a problem of compatibility between my computer and the RAM modules?

  If the RAM is damaged does these effects (do not start)?

  How can I check if the RAM modules are damaged?

  What would be your suggestions?

  I thank very you much in advance!

  Mauricio

  Hmm, I'd say you two bad sticks of RAM.  If the system POST even with them, I would swap them if you can.  We know that the RAM slots work because you have 4 x 4 sticks without any problem and your computer can take up to 32 GB of RAM.  Your admission that you bought the right kind of RAM, voltage, and speed, etc., so that shouldn't be a problem.  I would say as bad RAM.  When you do not install, just check that you make pairs in each of the colored slots, for example. matching pairs in the slot of white and black.

• Windows detects the USB device slowly.

  Separated from this thread.

  I have this problem on a Panasonic F1 - GZ Toughpad. It has a USB 3 port. It has 8 GB of memory, less than half used and it works my a request.

  The USB device is a FTDI USB KEY. This is a feature of full speed USB 2 (12 MB/s) according to the data sheet.

  When I plug a FTDI USB - KEY, it takes several seconds to detect the USB STICK. Also, it takes several seconds to detect when the USB STICK is disconnected.

  However, when I plug in a hub USB, plug the USB STICK in the hub, the detection is less than a second and the detection to be disconnected is less than a second.

  I can't use a USB hub as a work-around, because it is a portable application. Perhaps some of you could use a hub as a workaround. ... If someone has an answer to reduce response time, please let me know.

  The problem was solved by changing the parameters of the Toughpad BIOS for USB 3.0 to 2.0. Now the Toughpad detects the FTDI USB KEY in<1>

  Please note in the previous post, the USB hub is powered and the FTDI USB KEY is not memory flash, it's a serial USB port with a serial number, but only the serial number is available.

• Detect the installed application language packs

  Hi all

  Simple question: does anyone know how to detect the language packs installed on a smart phone BlackBerry to my application?

  Thank you!

  The Local.getAvailableLocales () method returns and table of available space (languages) on the BlackBerry Smartphone.

• Why my installed memory (RAM) displays 5,00 GB (1.99 GB usable) when I have the 8 GB? (using the 64 bit OS)

  I recently installed 2x2gb and 1x4Go of ddr3 ram, but when I go to 'System' it shows 5 GB (1.99 GB used) I am running 64-bit operating system and processor intel core i7 and I have no idea why this shows usable only 1.99 GB and 5 GB installed when im running a total of 8 GB

  In this configuration, you use a 1st question iSeries processor triple channel Intel 1366?

  The system will be the clock all the memory the same for the 1600 will be pointing down.

  Reported memory does not match the possibility that a DIMM has been missed. The only possibility is that they both bowed (double-sided) and only one bank has been detected.

  Check the manual of the motherboard, but you will have to run in Dual channel mode and use 2 and 4 for the 2 GB and 1 for the 4 GB.

• What is the maximum memory Ram with Windows XP, we can use

  Original title: GB

  In windows XP SP3, please I need to know GB maximum ram card, thanks to

  If you have a 32-bit version of Windows XP, then the maximum that you can install is 4 GB.  And if you do, you will not be able to access more than about 3 GB of it due to other resources that require address space.  Also check your plug to motherboard, there may be limits built into your motherboard.

  HTH,
  JW

• NB520 - upgrade the BIOS memory RAM

  Hello
  I have Toshiba NB520, and I would like to know if it is possible to change to a new 4 GB RAM?
  If I replace the 4 GB memory, the computer cannot restart!
  do you know why? I try to update the Bios without success.
  If an organization can help, thanks
  Best regards
  Scopman

  Yes it is possible. I have NB520-11. After reading many threads here I've done my own experiences.
  Using 4 GB RAM on preinstalled original Win7 starter doesn't have any effect because only 2 GB will be usable. I've install my own Win7 32-bit Home Premium and system displays now 4 GB installed and about 3 GB will be usable.

  To upgrade I ve used 4 GB of RAM on my Satellite P500. There PA3677U-1M4G part number.

• H8 - 1360t: restarts power - does not work with the installed memory

  HP clubhouse, i7, Windows 7, 3 x 4 GB, discreet grahics

  The computer turns on, then immediately restarts.

  No beeps.   Monitor says 'no signal '.

  I tried

  -different (new) hard drive - no change

  -current hard disk drive shows no errors; all the data is there

  -installed the new power supply - no change

  -removed the discrete video card; used another card discrete video - no change

  -cannot test on-board DVI video because it does not have the 4 holes next to the long bar. all my vga DVI connectors have the long bar with the four holes around it (sorry I don't know the different DVI connectors)

  What works:

  When I remove the memory, it will beep seeing that no memory is installed; AND the computer continues to operate (it is not restart).

  -J' tried memory (3 of them every 4 GB) as single and pairs between 2 blue 2 black slots grids.   No change

  -J' tried another key to 2 GB - no change

  Suggestions?

  Thank you

  Darryl

  Problem was the motherboard.   Replaced by the exact type as to doesn't interfere is not with the software installed.

  Everything plugged immediately when starting on the new motherboard.   The user has a problem with software that had to be put back.

  So-

  1. If the computer won't power more than 5 seconds

  2. change the components with known good components does not change the restart without end to power on

  It is the motherboard.

  Thanks for the help.

  Darryl

• Processor: Not Available & Installed memory (RAM): not available

  Hello, and I want to thank you in advance for the revision of my question.

  I've been searching for an answer on how to solve this problem for some time on the internet, and I'm still lost. When I right click on 'My Computer' on my desktop and select 'Properties' to see things such as my system partition and the RAM installed (I just put in a new kit yesterday, but the problem was before then.) or to perform administrative tasks, System Specs list shows nothing under CPU or RAM. I know that I have a single-core CPU clocked at 1.86 GHz and the RAM I installed is 2 GB, but the lack of information on this page that bothers me.

  I get no error message, it is simply not there. I'm not entirely sure when the problem started, so I don't know what software I installed around the time that is past, or if I've changed anything in the system. I tried to update my system partition, but I cannot think of anything to fix. Google has failed me.

  Does anyone have a solution? Even a list of things I could try (successfully or not) would be greatly appreciated.

  Thank you!

  Bill

  * EDIT * here is a screenshot of the problem: http://i54.tinypic.com/2r23gw2.png

  OK, here's the solution: My Windows Management Instrumentation service has been disabled. I searched for 2 hours again tonight for a solution. Someone said to remove a certain folder and restart this service. I went in my list of services, and I found that the service has been disabled altogether. I don't know how it happened, but when I put on "Automatic" and he began, my information was correctly once again! YAY!

  Thanks for all the help, you two.

  Bill