Wired WRT610N 1Gbits fall to 100 Mbps, after awhile

Similar Questions

• HP Envy 15 TS (C8P47AV): can't get Realtek GBE onboard Ethernet RTL8168 go above 100 Mbps

  I've only used my HP Envy TS 15 (C8P47AV) wireless and recently got a wired connection using CAT7 at my desk on the 2nd floor. I can't exceed 100 Mbps and it is extremely frustrating! I've read tons of things on the web and can not find something that helps! My WiFi gets a faster than the Ethernet cable speedtest. I see this change once! That's when I changed the cable that I have my router on and noticed he went to 300mbps and things flying. However him unplugging and plugging it into which he disappeared port. It's almost like the old bargaining hung. In any case change this to force it to work? I tried gigabit forced, you name it, any setting changes you fixed! I even tried to plug directly into the router port and that it did not. I have other devices that work fine with this same CAT7. I'm SOL with this version of HP laptop?

  I found the problem! After reading each thread only forum I could find on Google. Someone suggested to see if there was a brooch twisted in the connector and of course the middle one was bent! I don't know how it happened as I've only used wifi. It's a little tricky but I folded it back turned and I was ready to go! The chalk of it as not a cable problem or driver!

• WRT160N, auto-negotiation has failed at 100 Mbps, can wall jack be the cause?

  Hello

  Can someone please help me with may be a simple problem for you, but it starts to drive me crazy. Sorry in advance for the long post.

  WRT160N installed in the basement, linking (cable) 3 desktops and 2 laptops (wireless). When connecting by wire, some computers have troubles in autonegotiation speed, always end upward with connection failed. Force the speed of 10 Mbit/s full duplex solves the problem.

  Curiously, both computers have no problem to 100 Mbps Full Duplex auto-negotiation (HP nc8430 laptop with 5 years and the Broadcom NetXTreme Gigbyte old IBM ThinkCentre M50 8189-Tower network chip, I do not know the exact network chip, but I think that until the Gigabit). Less than 1 year of office by using a Committee of Asus P5N7A-VM with the integrated Realtek, also Gigabit network chip, still FAILED to negotiate at 100 Mbps. The wall plate has 4 Sockets. The question above is the same regardless of any plug used.

  After several attempts, I think I've isolated the cause to the wall outlet. There are about 6 metres of cable (~ 20 ft) between the router and the wall outlet. The computers connect to the wall using a cable of 2 meters (~ 7 ft). Go through the wall outlets, I pulled a 10 meter cable (~ 30 ft) connecting the router directly to the computer, then the computer is not always to 100 Mbps now could connect without any problems. So, this seems to indicate that the wall socket has altered the quality of the signal.

  The cables (between the router and the wall) are straight with T568B wiring (http://en.wikipedia.org/wiki/T568A/B#Wiring) the sockets are CAT5 RJ45 Keystone Jack free tool (http://www.amazon.com/CAT5-RJ45-Keystone-Jack-Black/dp/B000BSN7RO)

  So here are my questions:

  Q1. A wall outlet would cause a loss of significant signal or alteration?

  Q2. If the wall outlet is the cause of the loss of signal quality, how is it some computers have no trouble to autonegotiation to 100 Mbps Full Duplex and also when forced to 10 Mbps FD, all network problems disappear?

  Q3. And the most important question: can you please provide a solution?

  Thank you very much in advance for any help.

  Hello

  Follow up and FINAL solution to close this thread. The cause was the wall outlet. All sockets are of the type version tool-less Keystone Cat5e. All the exihit speed negotiation issue and can be used at 10 Mbit/s full duplex.

  I could borrow a punchdown tool and tried a new plug. This time, I tried Keystone Cat6 jack _WITH_ tool. Can be overkilled my cable is Cat5 only. But I don't want to take any risks because the price difference is negligible between Cat5e and Cat6 decision. The new Jack is working perfectly. The AutoDetect computer easily at 100 Mbit/s/s. The fix is so obvious, as soon as I replace threaded plug by a Jack of tool WITH the speed issue disappeared. I have connect / disconnect several times, even restarted the computer to ensure that the new Jack is working OK

  Although I'm not a guru in network cabling. But I'm not computer (using Windows & Linux) and I'm quite a handyman. I can't possibly screw up Assembly of ALL taken without tool, I've had. And the misconfiguration of the network in the operationg system is out of the question. Added to this fact that the new tool WITH jack is much easier to mount and all prectly work on the first attempt. I would say in conclusion that WITHOUT TOOL, CLAMP in Ethernet JACKS are UNSTABLE. At least that's my experience.

  It's pretty frustrating, that Jack is the last place I guess as a cause of a wiring problem. I changed to RJ-45 Sockets, wiring maps network and same router. All this has not solved until one day I discovered by chance that the cause was the wall outlet. (New computer loan with Ubuntu, I forgot to reduce the network speed to 10 Mb and directly connected to the switch without going through the wall socket and discovered that the computer can connect immediately to 100 MB).

  Hope this might help someone else.

• WNR2000 v2 does NOT offer to 100 Mbps port speed

  I got a plan of 100 / 10 MB/s and I noticed that with the WNR2000 v2 on a wired connection (cat 5e and cat 6), it is always capped at 75 / 10 Mbps.

  However, when I use gigabit router/modem my ISP, I get 130 / 10 Mbps.

  Why not reach the port on my router netgear speed, it's rated specs?

  

  

  I guess that you only use the ethernet connection.

  WNR2000v2 LAN port can handle 10 / 100 Mbit/s, but in reality you can't reach the exact speed or more than 100 Mbps.

  You were able to achieve more than 100 with the modem because the modem port is gigabit.

  It's a decent speed for this old model.

  You have the latest firmware installed?

  Try to do a reset and then see if it will improve.

  Just on the side note, you can see this table.

• work on 100 Mbps

  Hello, I am under a Pavilion g5345uk on windows 7 32 bit and would like to know how do I know if my network card was 1000mbps and if not what should I change

  also, it looks like my wireless card working just on 2.4 I could get it to work with 2.4 and 5 dualband

  Thanks for any help

  Hello:

  Your wired NETWORK interface is the Realtek RTL8103EL NIC with data transfer speeds: up to 10 / 100 Mbps.

  Your wireless NETWORK card is Ralink RT3090 WiFi card which is only able to transmit and receive on the 2.4 GHz band.

  There is a PCI slot on the motherboard. If it's free you can get a 10/100/1000 PCI network card and go into the BIOS and disable your onboard NIC.

  You can also get a PCIe x 1 10/100/Adapter network 1000 but I have read some posts where people don't get these work.

  I don't think it's everything you can do on the wireless card. On the PC HP laptop, they lock cards wireless not supported by the BIOS, and I don't know if they do on desktop too.

  You can disable your internal wireless card and buy an external USB dual band wireless adapter, I guess.

  Paul

• The "NVIDIA nForce 10/100 Mbps Ethernet" network card is not properly configured to use the IP Protocol on my HP vista.

  Initially my HP a6683w said that nvidia network controller experienced pilot or hardwear related issues, then NVIDIA had me download something and then restart my computer to see if the internet was starting to work again. Now, I restarted the computer and is trying to say that the adapter NVIDIA nforce 10/100 Mbps Ethernet have driver or hardware related issues. I want to just my internet to work again. How can I fix it?

  Hello

  1. have you made no hardware/software changes before the show?

  2. using an internet connection wired or wireless?

  3. are you a specific error message while trying to go online?

  Follow the steps mentioned below

  Method 1: Restart the computer using safe mode with active network.

  a. restart your computer.

  b. When you see the logo of the manufacturer of the computer, press F8.

  c. the display Advanced Startup Options , use the arrow keys to select Safe Mode with networkand press ENTER.

  d. connect to your computer with an account of a user who has administrator rights.

  Now check if you are able to connect to the network, if the problem persists, follow the next method

  Method 2:

  Follow the steps mentioned in the link and check with the question.

  http://Windows.Microsoft.com/en-us/Windows/help/network-connection-problems-in-Windows

  Method 3:

  Download and install the drivers from http://www.nvidia.com/Download/index.aspx?lang=en-us link with the question checking.

  It will be useful.

• Satellite C855-1j1 - LAN speed only only 100 Mbps instead of 1000 Mbps

  have gigabit router tp-link gigabit switch cat 5e cable only don't get 100 Mbps no 1000mbps on realtek pcle program my head fe family controller

  Is - this Windows 7?
  Sometimes 7 reports the speed being 100 even if its 1000.

• JWNR2010v5 (N300 wireless router) will support 100 Mbps connection speed internet in LAN?

  I intend to upgrate my internet connection speed of 60Mbps to 100 Mbps, but my provider says JWNR2010v5 (N300 wireless router) will not support 100 Mbps internet connection speed in LAN. Is this true? that which is the maximum speed of JWNR2010v5 for the LAN support. I don't mind the wireless speed, I use the maximum LAN. Thank you in advance.

  Your provider is correct. Either move your router to a router which supports! 000Mbps (MGI) LAN and WAN ports or stay at your current speed Interent.

  http://www.downloads.NETGEAR.com/files/GDC/datasheet/en/JWNR2010v5.PDF

• change the speed of the PC at 10 or 100 Mbps Ethernet link

  Hello

  I need to change speed Ethernet from the PC through program which is change the speed 10 or 100 Mbps.

  Is that possible, if yes, then please let me know the procedure.

  Or at least, I should be able to read the PC Ethernet speed in LabVIEW.

  Thank you

  You don't need .net 4.0 for this (.net 2.0 is pretty good) or anything else installed.

  I have attached a VI with control.

  PS: If you need to load assemblies .net 4.0 on to LabVIEW, you must follow the instructions in this link:

  http://digital.NI.com/public.nsf/allkb/32B0BA28A72AA87D8625782600737DE9

• HP PAVILION ELITE M9517C DESKT: NVIDIA NFORCE 10/100 Mbps Ethernet drivers upgrade

  I do a clean install for upgrade with Win 7 Pro 64-bit OEM. I ran the Win 7 Upgrade Advisor and need guidance on these issues, on what I need to do to upgrade:

  NVIDIA NFORCE 10/100 Mbps ethernet
  NVIDIA GeForce GT630
  NVIDIA High Definition Audio
  NVIDIA nForce System Management Controller

  Are these extensible & will work with Win 7 Pro 64-bit?

  Hello:

  You will need this chipset driver in order to install the ethernet (NVIDIA NFORCE 10/100 Mbps ethernet) and most of the other devices you listed.

  You should install this driver first and restart the computer before you install any other driver.

  http://www.nvidia.com/download/driverResults.aspx/30520/en-us

  According to the specifications of your model, it came with integrated graphics which means that you have added the video card.

  So you will not find this graphics driver on your PC support page.

  This is the latest driver for your GT630:

  http://www.nvidia.com/download/driverResults.aspx/81877/en-us

• Download never complete Hotmail - no error message and it seems to work when the wired adapter connection speed to 10 Mbps.

  Hello

  I have a Windows XP, annoying w. computer SP3 and IE 8. I am trying to attach something to a Hotmail email and it seems to download, but never finished (ever comes up with an error or anything like that). I work in a school and this seems to happen on computers at least 2 or 3, but not on others. I found a work around; Turning the connection of network cards speed to 10Mbps instead of 100 Mbps or Auto, but obviously this is not ideal because it cut speed considerably. Any help would be appreciated!

  Thank you

  Tom Wright.

  Hello

  1. is the issue limited to the Hotmail e-mail account?

  2. what web browser do you use?

  You can try to attach files to some other email account you have and check if the problem persists.

  If the question is limited to Hotmail, you can also post the question on the link provided below for assistance.

  Hotmail Portal

  http://windowslivehelp.com/product.aspx?ProductID=1

• E4200 why loss of huge packages to the concert but not 100 Mbps?

  Vista 64 Intel Pro 1000 with the latest driver here is a shot of the lagometer in COD Black Ops, when everything is good. I used to see this with my old WRT54GS and connected at 100 Mbps Full Duplex or half Duplex and I currently see it when it is connected through the E4200 to 100 Mbps full or half duplex AND connected via Gigabit via one of the 4 ports on the back of my cable modem, a Motorola SBG6580 [img][line] http://photos.smugmug.com/1590700194_rFrtpkV-O-LB.jpg this next screenshot It's what happens when I try to connect via Gigabit through the E4200. It either starts like this immediately or within 30 seconds to a minute, this will start to happen. I think that the red spikes indicate losses of packets. [img] http://photos.smugmug.com/1590700217_SWKtMP3-O-LB.jpg [line] .

  Looks like I have it solved.

  I got an Intel Pro 1000 PT NIC thug.

  The new Intel Pro 1000 CT works very well.  Without choking the E4200 and none seeing panic on the Gig switch 8 ports. Copies files to and from the NAS on the network are smooth and consistent transfer rate.

  And best of all... smooth gaming.

• WRT1900AC seems to limit myself to 10 Mbps when the gateway computer gets directly 100 Mbps

  My gateway xfinity is a TC8305C. I "bridged mode".

  If I have my computer directly in the front door, I speedtests of ~ 120mbps, no problem.

  However if I insert my Linksys WRT1900AC in the Middle, I get only for speeds of the order of 10-12 Mbps, MAX I tried three different Cat5e cables (including the one provided with the modem router and one supplied with the router) between the router & gateway, with no improvement in the result. The cable from the computer to the router is the same one that works > 100 Mbit/s if I connect directly to the front door.

  I need to use the router to run my network for a variety of reasons, but I don't want to give up 90% of my bandwidth!

  Did I miss something? Someone suggested, I set the ports manually to 100 Mbps instead of having their auto-negotiation, but I can't find any option for this in the firmware. My firmware version is 1.1.8.164461 which seems to be the latest version.

  Thanks in advance for any help!

  Brian

  Activate Media prioritization and set the bandwidth downstream to 120mbps exactly. Quit all devices and the app to normal priority.

• my cable internet connection is only 10Mbps and won't go to 100 Mbps windows Vista premium edition

  My inter connection wire line or hard earth runs only at 10 Mbit/s and should be 100 Mbit/s running vista Home premium and and using realtek rtl8168C (P) / 8111C (P) FAMILY GIGABIT ETHERNET NIC (NDIS 6.0).  How can I solve this problem.

  Hello

  I'm not aware of any Internet service provider that offers a 100 Mbps connection.

  The speed of the Internet connection is not a function of your material, but by the contract you have with the provider.

• Order of 100 Mbps with the same policy map on different interfaces of service-policy in routers

  We have several different interfaces in our routers. On that note, we have service-air to limit the bandwidth of 100 Mbps.

  If we use a sheet of class corresponding to a list of access as "permit ip any any".

  and map political with the class-map to the police up to 100 Mbit/s.

  If we apply this policy plan in the form of service-policy interface. All interfaces that use this service policy would share 100 Mbps or will they get 100 Mbps each?

  Thanks for any response.

  Concerning

  Henrik

  Hello

  As you apply the policy by interface, each interface will get 100 MB

  HTH