wireless router with built-in vpn client

Similar Questions

• WRTP54G (wireless router with phone connection) with Panasonic BL-C30A network camera (WEP only)

  Hello

  I would use this wireless router with WEP I can access the wireless camera (camera does only WEP encryption).
  The camera should be the only device authorized to connect to this wireless router.
  I can devote channel 11, so only use this wireless router
  I know that WEP can be cracked but I think maybe I can set up the router for it does not matter, i.e.,.
  While the camera is accessible by this particular router

  so my questions are:
  1. can I configure the router so only local outgoing LAN requests http are allowed?
  2. any other suggestions about the configuration of router that prevent access to my network?
  (using address filtering (by address mac camera only) MAC is worth, but I guess that the MAC address can be spoofed so not a complete solution)

  Thank you
  Tom

  I think that 'toomanydonuts' has provided my solution in this thread:

  solution wire

  Thank you

  Tom

• Routing problem between the VPN Client and the router's Ethernet device

  Hello

  I have a Cisco 1721 in a test environment.

  A net 172.16.0.0/19 simulates the Internet and a net 192.168.1.0/24 simulates the net, the VPN tunnel must go to (intranet).

  The net 172.16.0.0 depends on the router 0 FastEthernet, Intranet (VPN) hangs on Ethernet 0.

  The configuration was inspired form the sample Configuration

  "Configuring the Client VPN Cisco 3.x for Windows to IOS using Local extended authentication"

  and the output of the ConfigMaker configuration.

  Authentication and logon works. Client receives an IP address from the pool. But there's a routing problem

  side of routers. Ping client-side - do not work (the VPN client statistics that count encrypt them packets, but not to decrypt).

  Ping the router works too, but decrypt and encrypt customer statistics in VPN packets count progressive

  (customer has a correct route and return ICMP packets to the router).

  The question now is:

  How to route packets between the Tunnel and an Ethernet device (Ethernet 0)?

  conf of the router is attached - hope that's not too...

  Thanks & cordially

  Thomas Schmidt

  -.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.- snipp .-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.

  !

  version 12.2

  horodateurs service debug uptime

  Log service timestamps uptime

  encryption password service

  !

  !

  host name * moderator edit *.

  !

  enable secret 5 * moderator edit *.

  !

  !

  AAA new-model

  AAA authentication login userauthen local

  AAA authorization groupauthor LAN

  !

  ! only for the test...

  !

  username cisco password 0 * moderator edit *.

  !

  IP subnet zero

  !

  audit of IP notify Journal

  Max-events of po verification IP 100

  !

  crypto ISAKMP policy 3

  3des encryption

  preshared authentication

  Group 2

  !

  ISAKMP crypto client configuration group 3000client

  key cisco123

  pool ippool

  !

  ! We do not want to divide the tunnel

  ! ACL 108

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

  !

  Crypto-map dynamic dynmap 10

  Set transform-set RIGHT

  !

  map clientmap client to authenticate crypto list userauthen

  card crypto clientmap isakmp authorization list groupauthor

  client configuration address map clientmap crypto answer

  10 ipsec-isakmp crypto map clientmap Dynamics dynmap

  !

  interface Ethernet0

  no downtime

  Description connected to VPN

  IP 192.168.1.1 255.255.255.0

  full-duplex

  IP access-group 101 in

  IP access-group 101 out

  KeepAlive 10

  No cdp enable

  !

  interface Ethernet1

  no downtime

  address 192.168.3.1 IP 255.255.255.0

  IP access-group 101 in

  IP access-group 101 out

  full-duplex

  KeepAlive 10

  No cdp enable

  !

  interface FastEthernet0

  no downtime

  Description connected to the Internet

  IP 172.16.12.20 255.255.224.0

  automatic speed

  KeepAlive 10

  No cdp enable

  !

  ! This access group is also only for test cases!

  !

  no access list 101

  access list 101 ip allow a whole

  !

  local pool IP 192.168.10.1 ippool 192.168.10.10

  IP classless

  IP route 0.0.0.0 0.0.0.0 172.16.12.20

  enable IP pim Bennett

  !

  Line con 0

  exec-timeout 0 0

  password 7 * edit from moderator *.

  line to 0

  line vty 0 4

  !

  end

  ^-^-^-^-^-^-^-^-^-^-^-^-^- snapp ^-^-^-^-^-^-^-^-^-^-^-^-^-^-

  Thomas,

  Can't wait to show something that might be there, but I don't see here. You do not have the card encryption applied to one of the interfaces, perhaps it was not copied. Assuming your description you do it, or should it be, applied to the fa0 and you are connected. Try how you ping? Since the router or a device located on E0? If you ping the router, you will need to do an extended ping of E0 to the ip address of the client has been assigned. If your just ping the router without the extension, you will get sales and decrypts that you declare on the client. Have you tried to ping from the client to interface E0? Your default route on the router is pointing to fa0? You have a next hop to affect? You have several NIC on the client pc? Turn off your other network cards to check that you don't have a problem with routing on the client if you have more than one.

  Kurtis Durrett

• RV120 VPN with full Cisco VPN Client?

  Is it possible to configure the RV120 for a VPN IPsec for use with the complete Cisco VPN client?

  I tried, but it does not appear to support "Goup of authentication.

  I see in the confi router I can put a PSK, but the complete VPN client seems only accecpt "Goup authentication."

  I managed on the basis for the work "Fast VPN", how it works is beyond me, because he does not appear to create an adapter with an IP address or anything on the local line, and I didn't even create a VPN policy...

  Or put another way, what alternative (Free) VPN clients are there to work with the RV120?

  Try the following link for instructions for Cisco VPN and the SA500:

  http://www.Cisco.com/en/us/docs/security/multi_function_security/multi_function_security_appliance/sa_500/TechNote/note/SA500_vpnclient_appnote.PDF

  I hope this helps.

  Thank you

  Rick Roe

  Cisco Small Business Support Center

• Routing issue of Cisco VPN Client ASA

  Hi, I use a Barracuda NG for firewalls and I would use a Cisco ASA 5505 for VPN Client connections. But I have the problem that I can't get a connection to the VPN PC connected to the internal network. But I can reach the VPN connected PC from the inside. Here is a diagram of my network:

  cisco_asa_prob.jpg

  

  Here the IP Configuration and the routing of the Barracuda firewall table:

  screen_shot_2014-08 - 12_at_16.01.42.png

  

  I have a route on the Barracuda NG to the 10.10.10.0/24 network VPN Client on eth0.

  The 192.168.1.0/24 LAN I ping the Client comes with Client VPN 10.10.10.11 as it should. But I can't ping or access network resources in the local network for AnyConnected customer's PC that connected through the VPN.

  Here is the config Cisco ASA:

   : Saved : : Hardware: ASA5505, 512 MB RAM, CPU Geode 500 MHz : ASA Version 9.2(2) ! hostname leela names ip local pool VPN-Pool 10.10.10.10-10.10.10.200 mask 255.255.255.0 ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 switchport access vlan 5 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.250 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address dhcp ! interface Vlan5 nameif dmz security-level 50 ip address 172.16.0.250 255.255.255.0 ! ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server 192.168.1.10 same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network obj_any subnet 0.0.0.0 0.0.0.0 object network VPN-Pool subnet 10.10.10.0 255.255.255.0 description VPN-Pool object network NETWORK_OBJ_10.10.10.0_24 subnet 10.10.10.0 255.255.255.0 access-list inside_access_in extended permit ip any any access-list inside_access_in extended permit ip object VPN-Pool any access-list dmz_access_in extended permit ip any any access-list global_access extended permit ip any any access-list outside_access_in extended permit ip any any pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 mtu dmz 1500 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 no arp permit-nonconnected nat (inside,dmz) source static any any destination static NETWORK_OBJ_10.10.10.0_24 NETWORK_OBJ_10.10.10.0_24 no-proxy-arp route-lookup inactive access-group inside_access_in in interface inside access-group outside_access_in in interface outside access-group dmz_access_in in interface dmz access-group global_access global route dmz 0.0.0.0 0.0.0.0 172.16.0.254 1 route inside 0.0.0.0 0.0.0.0 192.168.1.254 tunneled timeout xlate 3:00:00 timeout pat-xlate 0:00:30 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy server-type microsoft user-identity default-domain LOCAL aaa authentication enable console LDAP_SRV_GRP LOCAL aaa authentication http console LDAP_SRV_GRP LOCAL aaa authentication ssh console LDAP_SRV_GRP LOCAL aaa authentication serial console LOCAL http server enable 444 http 192.168.1.0 255.255.255.0 inside snmp-server location Vienna crypto ipsec ikev2 ipsec-proposal DES protocol esp encryption des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal 3DES protocol esp encryption 3des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES protocol esp encryption aes protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES192 protocol esp encryption aes-192 protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES256 protocol esp encryption aes-256 protocol esp integrity sha-1 md5 crypto ipsec security-association pmtu-aging infinite crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map inside_map interface inside crypto map dmz_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map dmz_map interface dmz crypto ca trustpoint ASDM_TrustPoint0 enrollment self subject-name CN=leela proxy-ldc-issuer crl configure crypto ca trustpoint ASDM_TrustPoint1 enrollment terminal crl configure crypto ca trustpool policy crypto ca certificate chain ASDM_TrustPoint0 quit crypto ikev2 policy 1 encryption aes-256 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 10 encryption aes-192 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 20 encryption aes integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 30 encryption 3des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 40 encryption des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 enable dmz client-services port 443 crypto ikev2 remote-access trustpoint ASDM_TrustPoint0 telnet timeout 5 no ssh stricthostkeycheck ssh 192.168.1.0 255.255.255.0 inside ssh timeout 30 ssh key-exchange group dh-group1-sha1 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.254-192.168.1.254 inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept dynamic-filter updater-client enable dynamic-filter use-database ntp server 192.168.1.10 source inside ssl trust-point ASDM_TrustPoint0 dmz ssl trust-point ASDM_TrustPoint0 inside webvpn enable dmz no anyconnect-essentials anyconnect image disk0:/anyconnect-macosx-i386-3.1.05170-k9.pkg 1 anyconnect image disk0:/anyconnect-win-3.1.05170-k9.pkg 2 anyconnect image disk0:/anyconnect-linux-3.1.05170-k9.pkg 3 anyconnect image disk0:/anyconnect-linux-64-3.1.05170-k9.pkg 4 anyconnect profiles AnyConnect_client_profile disk0:/AnyConnect_client_profile.xml anyconnect enable tunnel-group-list enable group-policy DfltGrpPolicy attributes default-domain value group-policy GroupPolicy_AnyConnect internal group-policy GroupPolicy_AnyConnect attributes wins-server none dns-server value 192.168.1.10 vpn-tunnel-protocol ikev2 ssl-client webvpn anyconnect profiles value AnyConnect_client_profile type user group-policy portal internal group-policy portal attributes vpn-tunnel-protocol ssl-clientless webvpn url-list none username tunnel-group AnyConnect type remote-access tunnel-group AnyConnect general-attributes address-pool VPN-Pool authentication-server-group LDAP_SRV_GRP default-group-policy GroupPolicy_AnyConnect tunnel-group AnyConnect webvpn-attributes group-alias AnyConnect enable tunnel-group Portal type remote-access tunnel-group Portal general-attributes authentication-server-group LDAP_SRV_GRP default-group-policy portal tunnel-group Portal webvpn-attributes group-alias portal enable! ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 ! prompt hostname context no call-home reporting anonymous hpm topN enable : end no asdm history enable

  Can someone please help me solve this problem?

  When I tried to solve this I didn't choose which interface the Packet Tracer?

  The interface inside or DMZ interface?  Inside, he says it will not work with the dmz but the error did not help me

  Anyone here knows why it does not work?

  screen_shot_2014-08 - 12_at_16.34.57.png

  

  screen_shot_2014-08 - 12_at_16.33.06.png

  

  Hello

  Inside LAN is directly connected to the right firewall VPN... then I don't think you have to have the itinerary tunnele... can you try to remove the road tunnel mode and check.

  entrance to the road that is static to achieve 10.10.10.11 as its display is correct...

  Route by tunnel watch also with 255 administrative distance.  I've never used that in my scenarios... lets see...

  Concerning

  Knockaert

• IPP with Ezvpn and VPN Clients

  Hello

  I have a 5585 ASA running on 8.4. I have it set to accept the ezvpn NEM mode clients and then push the routes through IPP in the OSPF via redistribution on a list sheet road. Now I came with a second condition of the addition of VPN Clients to the same firewall. In the current configuration if I activate customers, they will push the 32 routing updates in the routing table makes a table long enough and I don't want to do that. What I understand of the redistribution of static route is that:

  (1) road should be static in the routing of ASA, inserted through IPP table or manually added

  (2) my redistribution list will allow all the roads that fall within the specific subnet.

  If I have a 192.168.1.0/24 defined in the ACL of redistribution, a route in this 24 will be added to the routing table. Please refer to the sample configuration:

  http://www.Cisco.com/en/us/partner/products/ps6120/products_configuration_example09186a00809d07de.shtml

  In the example of config is the road added to the list redisttribution/24 network but if you examine the output at the end of the document, a 32 road has been inserted in the router's routing table.

  I want to keep Ezvpn with IPP clients and at the same time to have VPN Clients running without IPP. Would appreciate any help in this!

  Thank you

  Sylvana

  Route-synthesis is only possible if for OSPF routers ABR/ASBR. I wasn't talking another ospf process, but on another area ospf.

  if I add summary-address for only my client vpn pool (10.10.0.0/16) will  my other routes for ezvpn stop being advertised or will they continue  to be advertised as before and only VPN Pool would be summarized?
  

  If you select the summary for 10.10.0.0/16 only that the network will be sumarized. Why would another announcement due to the synthesis of 10.10.0.0/16 cease?

• Have problems with the IPSec VPN Client and several target networks

  I use an ASA 5520 8.2 (4) running.

  My goal is to get a VPN client to access more than one network within the network, for example, I need VPN client IPSec and power establish tcp connections on servers to 192.168.210.x and 10.21.9.x and 10.21.3.x

  I think I'm close to having this resolved, but seems to have a routing problem. Which I think is relevant include:

  Net1: 192.168.210.0/32

  NET2: 10.21.0.0/16

  NET2 has several subnets defined VIRTUAL local network:

  DeviceManagement (vlan91): 10.21.9.0/32

  Servers (vlan31): 10.21.3.0/32

  # See the road

  Code: C - connected, S - static, RIP, M - mobile - IGRP, R - I, B - BGP

  D - EIGRP, OSPF, IA - external EIGRP, O - EX - OSPF inter zone

  N1 - type external OSPF NSSA 1, N2 - type external OSPF NSSA 2

  E1 - OSPF external type 1, E2 - external OSPF of type 2, E - EGP

  i - IS - L1 - IS - IS level 1, L2 - IS - IS IS level 2, AI - IS inter zone

  * - candidate by default, U - static route by user, o - ODR

  P periodical downloaded static route

  Gateway of last resort is x.x.x.x network 0.0.0.0

  C 192.168.210.0 255.255.255.0 is directly connected to the inside

  C 216.185.85.92 255.255.255.252 is directly connected to the outside of the

  C 10.21.9.0 255.255.255.0 is directly connected, DeviceManagement

  C 10.21.3.0 255.255.255.0 is directly connected, servers

  S * 0.0.0.0 0.0.0.0 [1/0] via x.x.x.x, outdoor

  I can communicate freely between all networks from the inside.

  interface GigabitEthernet0/0

  Description * INTERNAL NETWORK *.

  Speed 1000

  full duplex

  nameif inside

  security-level 100

  IP 192.168.210.1 255.255.255.0

  OSPF hello-interval 2

  OSPF dead-interval 7

  !

  interface Redundant1.31

  VLAN 31

  nameif servers

  security-level 100

  IP 10.21.3.1 255.255.255.0

  !

  interface Redundant1.91

  VLAN 91

  nameif DeviceManagement

  security-level 100

  IP 10.21.9.1 255.255.255.0

  permit same-security-traffic inter-interface

  NO_NAT list of allowed ip extended access all 172.31.255.0 255.255.255.0

  IP local pool vpnpool 172.31.255.1 - 172.31.255.254 mask 255.255.255.0

  Overall 101 (external) interface

  NAT (inside) 0-list of access NO_NAT

  NAT (inside) 101 192.168.210.0 255.255.255.0

  NAT (servers) 101 10.21.3.0 255.255.255.0

  NAT (DeviceManagement) 101 10.21.9.0 255.255.255.0

  static (inside, DeviceManagement) 192.168.210.0 192.168.210.0 netmask 255.255.255.0

  static (inside, servers) 192.168.210.0 192.168.210.0 netmask 255.255.255.0

  static (servers, upside down) 10.21.3.0 10.21.3.0 netmask 255.255.255.0

  static (DeviceManagement, upside down) 10.21.9.0 10.21.9.0 netmask 255.255.255.0

  access list IN LAN extended permitted tcp 192.168.210.0 255.255.255.0 any

  access list IN LAN extended permit udp 192.168.210.0 255.255.255.0 any

  LAN-IN scope ip 192.168.210.0 access list allow 255.255.255.0 any

  LAN-IN extended access list allow icmp 192.168.210.0 255.255.255.0 any

  access list IN LAN extended permitted tcp 10.21.0.0 255.255.0.0 any

  access list IN LAN extended permitted udp 10.21.0.0 255.255.0.0 any

  LAN-IN scope 10.21.0.0 ip access list allow 255.255.0.0 any

  LAN-IN extended access list allow icmp 10.21.0.0 255.255.0.0 any

  standard access list permits 192.168.210.0 SPLIT-TUNNEL 255.255.255.0

  standard access list permits 10.21.0.0 SPLIT-TUNNEL 255.255.0.0

  group-access LAN-IN in the interface inside

  internal VPNUSERS group policy

  attributes of the VPNUSERS group policy

  value of server DNS 216.185.64.6

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value of SPLIT TUNNEL

  field default value internal - Network.com

  type VPNUSERS tunnel-group remote access

  tunnel-group VPNUSERS General attributes

  address vpnpool pool

  strategy-group-by default VPNUSERS

  tunnel-group VPNUSERS ipsec-attributes

  pre-shared key *.

  When a user establishes a VPN connection, their local routing tables have routes through the tunnel to the 10.21.0.0/16 and the 192.168.210.0/32.

  They are only able to communicate with the network 192.168.210.0/32, however.

  I tried to add the following, but it does not help:

  router ospf 1000

  router ID - 192.168.210.1

  Network 10.21.0.0 255.255.0.0 area 1

  network 192.168.210.0 255.255.255.252 area 0

  area 1

  Can anyone help me please with this problem? There could be a bunch of superfluous things here, and if you could show me, too, I'd be very happy. If you need more information on the config, I'll be happy to provide.

  Hello Kenneth,

  Based on the appliance's routing table, I can see the following

  C 10.21.9.0 255.255.255.0 is directly connected, DeviceManagement

  C 10.21.3.0 255.255.255.0 is directly connected, servers

  C 192.168.210.0 255.255.255.0 is directly connected to the inside

  And you try to connect to the 3 of them.

  Politics of Split tunnel is very good, the VPN configuration is fine

  The problem is here

  NO_NAT list of allowed ip extended access all 172.31.255.0 255.255.255.0

  NAT (inside) 0-list of access NO_NAT

  Dude, you point to just inside interface and 2 other subnets are on the device management interface and the interface of servers... That is the question

  Now how to solve

  NO_NAT ip 192.168.210.0 access list allow 255.255.255.0 172.31.255.0 255.255.255.0

  no access list NO_NAT extended permits all ip 172.31.255.0 255.255.255.0

  NO_NAT_SERVERS ip 10.21.3.0 access list allow 255.255.255.0 172.31.255.0 255.255.255.0

  NAT (SERVERS) 0 ACCESS-LIST NO_NAT_SERVERS

  Permit access-list no.-NAT_DEVICEMANAGMENT ip 10.21.9.0 255.255.255.0 172.31.255.0 255.255.255.0

  NAT (deviceManagment) 0-no.-NAT_DEVICEMANAGMENT access list

  Any other questions... Sure... Be sure to note all my answers.

  Julio

• With PUBLIC IP VPN client

  Could Hi someone help me? There is a PC VPN client whose public (without NAT router) IP address, it can connect to the server EZVPN and recive reoutes but traffic is not passing,.

  Yes

  the Transport TCP value on the client side, with the tcp f.i. 10000 port and make sure that the VPN box can talk tcp 10000 more too.

  If a customer has a public ip address, it will be successfully Setup a VPN, but can't access anything via UDP with NAT T.

  If configure you the TCP transport, it will be.

• How to share files and printers between windows xp desktop that is connected to a wireless router with a laptop running windows 7. printer is connected to the desktop computer

  Hi all.  I normally wouldn't have a problem with that, but I must be missing something.  I want to create a home network or small business between my desktop running windows xp pro sp3 and my laptop running windows 7 Home premium.  I want to share files and printers.  My desktop with windows xp computer is connected to a wireless router.  The printer is connected to my desktop as well.  My laptop is wireless with the wireless router.  I tried everything I can think of to get these two devices to the network.  If anyone can help.  Don't forget, my printer is connected to my desktop with windows xp and is connected to my wireless router which is connected to my cable modem.  Internet works fine.  the laptop with windows 7's wireless and internet works fine.  just impossible to get the two see each other or share what anyone.  Thank you.

  With respect to the sharing of printer (s), microsoft has a utility called 'Print Migrator'

  Download & install, create copy, send a copy to the other pc to share its use.

• With the help of WRT300N Wireless Router with a USB modem (satellite)?

  Hey there!  I tried to find this answer in various places online, and I saw a few things that have led me to believe that this is possible, but nothing to explain as thoroughly as I'd like.  I have a N of Linksys WRT300N wireless router.  For the next few months, new home construction we do service by cable or DSL, so we use the Cricket's broadband Internet, which connects via a USB port (Cricket is a 3G network, managed by a cell phone company).

  I'm trying to understand if there is anyway that I can connect internet Cricket USB to my computer, as usual, but then connect my router to the computer somehow so that I can distribute this wireless signal?  I'm having crazy to move the thing USB from one computer to another and would really like to connect my PS3 wireless signal, thus.

  Does anyone have an idea how this could be done?  If so, could you explain to me what I need to do quite exactly?  I am running Windows Vista on this computer.  Thank you very much in advance for your help.  You're going to be spare me months with a value of pulling my hair out, believe me.

  Yes you can do it, USB Modem not connecting to the computer, the computer must be connected to the Internet Port of the router and then it will give a Wi - Fi connection and...

  To do this, you need to enable Internet Connection Sharing (ICS)...

• Routing between the easy VPN clients

  I have easy installation of multiple ASA5505 as VPN clients connecting to a single ASA5510 and can route packets between client subnets easy 5505. Anyone has the clues, how?

  Thank you!

  You must add the below to the 5510: -.

  permit same-security-traffic intra-interface

  HTH >

• Modem/wireless router with USB port

  Qwest (my IP) told me that there is nothing like a modem/router with a USB port.  Am I crazy or what?

  Karibou

  Hello
  Welcome to the HP Forum!

  Karibou wrote:

  Qwest (my IP) told me that there is nothing like a modem/router with a USB port.  Am I crazy or what?

  Qwest is wrong. There are a number of manufacturers that make routers wireless with USB ports. This is a new trend.

  D - Link makes this one. Unfortunately, it has been abandoned. Linksys makes this one.

  Belkin makes one in this video.

• Unable to connect to a wireless router with my laptop

  I bought a laptop on 12/26/08 and now I have technical difficulties with regard to the internet wirelessly, via the LAN connection it s ok and wireless radar can see all available networks, but cannot communicate with them.

  It starts and then say that it s a unverified network and just say connect but don't make any progress, and the internet is still not functional

  I m using the router without wire of 7mg eircom and is placed outside the door of the room of my bed with full strength.

  It would be interesting to know what laptop you have.

  Have you tried to update the driver WLAN? You can find it on the Toshiba site:
  http://EU.computers.Toshiba-Europe.com

  Have you tested the connection without security as a hidden SSID, MAC address filtering and so far? Try this.

• Belkin G wireless router with packet loss

  Hey im having a problem with my Belkin G Router wireless.  Sometimes, I need to plug allow a person with a laptop computer to connect to the internet, but as soon as I do, I become unable to find servers for online games.  When checking my connection on speedtest.net, I stumbled on Pingtest.net, I tried and found that I had a 88% packet loss.  I tried to configure to DMZ with no effect... What can I do?
  Desktop Gateway W3650 all standard parts
  Wireless Belkin G F5D7234-4 v3 router
  Webstar DPC2100 modem

  It works up until I plug the router

  "Packet loss" is probably artificial due to the firewall of the router.  To check, go to http://192.168.2.1/ and click 'Firewall' on the left side and turn off.  Now try again, you should be getting 0% loss.  It worked for me.

  You can enable it after checking.  I don't know that it actually reduces performance, it makes just hard to perform this test. ... I think so.

• You need to configure a wireless router with my office so I can use ipad. What should I really?

  I have a modem cable from Time Warner (Roadrunner) for internet access. Should I just a router, or do I need to install an adapter (card or USB type)?

  You don't need to install anything in your desktop PC. Wireless routers have ethernet ports you can connect to your PC with a cable.