With the help of the EA 6300 as Access Point?

Similar Questions

• My HP Officejet 6500 E710a-f can communicate with the router or wireless access point

  I don't even know if my printer supports wireless or not there only ethernet logo on it and no wireless setting in its control panel as shown in the manual, I plugged on the router via a cable many years ago but now, for some reason, I need get the router of the printer if it can communicate with the Wireless router and if she can , how it will be, and to ensure in this... I have no parameters to talk wireless in the printer, but as I remember in his specification he supported wireless do not know if I got the wrong specifications or my printer is missing something.

  and it is my printer status

  Hello

  Unfortunately, it is not a wireless printer:

  http://h30434.www3.HP.com/T5/printer-networking-and-wireless/my-OfficeJet-6500-E710a-f-wont-print-wirelessly-Windows-7/TD-p/1820813

  Kind regards.

• Configure the WRT610N as an access point?

  I have a local wired network with a WAP54G access point that connects the 2 laptops wireless for the local network and internet.  I want to replace the access point with a WRT610N.   How to configure the WRT610N as an access point?   Can I connect my access point to the Internet on the WRT610N, or to one of the four ethernet ports cable Cat6?

  Thanks for the help.

  
  

• Connection of comments on the second WNR1000v3 as access point does not connect to Internet

  I have a WNR1000v3 (firmware V1.0.2.68_60.0.93NA) connected to the WAN and it works well. His IP address is 192.168.0.1, subnet 255.255.255.0, gateway 192.168.0.1, mask and DNS servers are on 8.8.8.8/8.8.4.4. DHCP is configured to 192.168.0.10 to 192.168.0.100. I have a guest connection configured and it works well.

  I have a * second * WNR1000v3 (same firmware) bound to the first as access by using these instructions: http://kb.netgear.com/app/answers/detail/a_id/23784/~/how-to-automatically-configure-a-netgear-route...

  I gave him the IP 192.168.0.2, subnet mask 255.255.255.0, gateway 192.168.0.1, and DNS servers again the value of Google. It has the same SSID wireless as the main router and I can move seamlessly between the two. The devices connected to the LAN ports on this access point work very well. Wireless connection works fine.

  I then configured the connection even guest on the second router (the one running in access point mode) and I can get an IP address when I use it. However I can't access the Internet. Ping 192.168.0.1, 192.168.0.2, and 173.194.33.137 (the IP local google.com) all fail.

  Guest connection is not supported on a router functioning as an access point? Or am I missing something really obvious?

  Thank you

  Bill

  @storm1985 I suspect that your configuration means that all the second router LAN ports will also forward only to the Internet. But this gives me a good idea to use another router just like an access point wireless for the connection of comments. (I seem to accumulate old routers.) Unfortunately, I don't have the time to try this out until late in the week, but I'll certainly do and report. Thank you!

• Need help with the error msg 1120: access of undefined property

  I'm not a coder, so I need help coding. Any help would be greatly appreciated.

  I'm a Flash banner that was given instructions "clickTAG" of Google. The code, they said to put the button is:

  Parameter ClickTAG for ActionScript 3 code:

  import flash.events.MouseEvent;
  import flash.net.URLRequest;
  // ......

  
  () someButton_or_displayObject_to_receive_mouseClick.addEventListener
  MouseEvent.CLICK,
  function(Event: MouseEvent): void {}
  flash.net.navigateToURL (new URLRequest (root.loaderInfo.parameters.clickTAG), '_blank');
  }
  );

  Replace someButton_or_displayObject_to_receive_mouseClick with the actual name of the button that will receive the click.

  Note that it is not necessary to specify the destination URL of the ad anywhere in this code; This is supported through the use of "clickTAG". In addition, according to the structure of your Flash Ad, it may be necessary to add "_root." or "_level0." for "clickTAG" above, resulting in a "_root.clickTAG" or "_level0.clickTAG". It is strongly recommended to download the ad on your account and check the ad behaves normally until she'll live, granted for the necessary changes.

  And this is the code that I put in (btnClickTag is the name of my button):

  import flash.events.MouseEvent;

  import flash.net.URLRequest;

  
  

  
  

  () btnClickTag.addEventListener

  MouseEvent.CLICK,

  function(Event: MouseEvent): void {}

  flash.net.navigateToURL (new URLRequest (root.loaderInfo.parameters.clickTAG), '_blank');

  }

  );

  and this is the error I got:

  Scene1, layer 'actions', image1, 1120: access of undefined property btnClickTag. () btnClickTag.addEventListener

  First of all, make sure that you have assigned this name to the button using the properties panel, and then, don't forget to adjust the code so that it is not spread over several lines... normally it must be on a single line.  Do not nest the function where the listener either, so try the following (not necessary for import declarations)...

  btnClickTag.addEventListener (MouseEvent.CLICK, tagClick);

  function tagClick(event:MouseEvent):void {}

  navigateToURL (new URLRequest (root.loaderInfo.parameters.clickTAG), '_blank');

  }

• Help to set up the Linksys WRT54GH as Access Point

  I would like to connect my WRT54GH to my main router with RJ45 (so I can get the signal full force) in order to be used as a point of access but I m not sure about the configuration. Can someone help me configure my WRT54GH?

  Kind regards.

  Manual.

  Follow the instructions for 'LAN to LAN' Cascading in the link below:

  In waterfall or connect a Linksys router to another router

  Thing to keep in mind when cascading a router:

  1. Change the IP address of the secondary router to something like 192.168.1.254 so its on the same network, but is not in conflict with the main router
  2. Make sure that the DHCP service is disabled on the secondary router
  3. Make sure that nothing is ever connected to the Internet port on the secondary router
  4. Differentiate the wireless SSID by location (Ex: downstairs) and the channel

• urlLoader - replace it with the File class to access external resources

  Hello.

  Just read up on the File class more than anything because I want to develop on mobile devices. Can I replace all my classes urlLoader with the File class for my games on the web.

  var prefsFile:File = File.applicationDirectory;

  prefsFile = prefsFile.resolvePath ("preferences.xml");

  I feel that it is perhaps a silly question, but I have to ask.

  See you soon

  Yes, but you probably don't want to use applicationDirectory because of security concerns.

  and is there a reason you can't use your urlloaders?

• Problem with the MEMO in MS ACCESS field

  I have the column in the table with the MEMO data type - "" for the description of the product (long text, much more than 255 characters) and use SQL UPDATE or INSERT, but with < cfqueryparam cfsqltype = "cf_sql_tlob"... > or < cfqueryparam cfsqltype = "cf_sql_longvarchar"... > I can insert max 510 characters. If I use COLUMNNAME = ' #form. FIELDNAME # '-everything is ok. Where is the problem? Maybe I should use a different cfsqltype? (CF MX 7)

  You need to use .

  Now go to the CF Administrator and examine the datasource YYY.

  The driver should say "Microsoft Access".

  Now, click on the link to change, and then "show advanced settings". What is the value of 'Long text buffer?

• The connection between your access point, router or cable modem and the Internet is broken...

  -router

  connection internet dropmy every 20 minutes and again after one minute everything is as before... pls help has me... mb my router is a waste

  Wire? Wireless? Status of other computers (if any)? Router? Network devices? Type of Internet connection?

  Have you other computers can connect to the Internet using the same network hardware?

  You have any kind of 3rd party Network Manager installed, like Hello, Netmagic and the likes?

  Do you have the "Fancy" 3rd part security suits, or as the hybrid of nVidia Firewall Firewall.

  You are using more than one firewall (including native Windows), AV or other security applications active?

  If you use any 3rd part above, try to configure them to work corretly on your network, or get rid of them and see if it helps (RID, means getting rid, not just disable ).

  ------------------

  Assuming that you are connected with the wireless to the router.

  First scan the computer against the viruses and Malwares.

  When you are sure that it is clean.

  These steps and tell us where is the breaking point.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  ------------------

  The wireless card drivers much also install utility wireless of the seller.

  Make sure that if there are teas from Wireless Utility of seller does not work with the native Windows wireless utility (Service WLAN).

  ----------------

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible set up the firewall correctly, otherwise totally uninstall and get rid of its remaining processes that permit the own local network traffic flow.

  If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  party like Hello and NetMagic 3rd network managers can block local traffic too.

  ---------------------------

  Stack TCP/IP work should look like.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  http://www.ezlan.NET/Win7/status-NIC.jpg

  Description is the data of the card making.

  The physical address is MAC of the card number.

  The xx must be a number between 0 and 255 (all xx even number).

  YY should be between 0 and 255

  ZZ should be between 0 and 255 (zz all the same number.)

  The date of the lease must be valid at the present time.

  * Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.

  * Note 2. There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.

  ---------------------------------------------------

  A message in the small window that says connected wireless doesn't means that you are really a valid functional connection.

  Above everything is OK, you must be able to connect to the router.

  Connection to the router means that you can enter the IP of the router base in an address bar in one go, being able to connect and configure the router menus see.

  If it doesn't connect to the router, journal newspaper from any computer that can connect to the router wirelessly with a wire, disable wireless security, make sure that the wireless SSID broadcast is enabled and try to connect with no. wireless security.

  Enable security wireless after you eat to make a functional connection.

  
  

  Jack - Microsoft MVP, Windows networking. WWW.EZLAN.NET

• "The connection between your access point router or modem cable, and the internet is broken"

  It is a constant frustration for me sorce. My office gives me this error at least once per hour. I changed the wireless pci card (old one finally died but managed to stay in line!) to a usb dongle, and then to the diffenert pci card, and now I'm in a usb port, which is the same brand as the map oringal that worked. As it is, I can be online long enough to get hope and then... Poof nothing.  I do clean boots, refreshed earworm, did the whole ' IVF it ' was bound to him on a previous post, the netsh command reset. Nothing did. I know that's not the router because all other computers in the House including my laptop can connect.  What Miss me?

  Any help would be loved!

  Hey Tyler,

  Thanks for the reply and keeping the status updated. I appreciate the troubleshooting that you tried it on the computer.

  The issue could be a conflict of others on the computer.

  I suggest you to check the problem in Mode safe mode with networking:

  http://Windows.Microsoft.com/en-us/Windows/Start-computer-safe-mode#start-computer-safe-mode=Windows-7

  If you can't find the problem with Safe Mode with networking, I suggest you perform a clean boot on the computer and check with the question:

  I suggest you follow the link below to find out how to place the computer in a clean boot.

  https://support.Microsoft.com/kb/929135

  Note: Reset the computer in Normal mode once you have completed troubleshooting as a result of the "How to reset the computer to start normally after a boot minimum troubleshooting" section of this article.

  Just reply with the results. I'll be happy to help you.

• There is no communication between devices that are connected to the Linksys WAP4410N Wireless access point?

  Hi all

  I have deployed the new Linksys WAP4410N Wireless Access Point and it works fine. Laptop which is connected to the AP may be able to access the internet. It can communicate with AP and also the gateway IP (IP Router) but it is wireless devices are not able to communicate with each other. In the case of peripheral LAN can communicate with wireless devices. Cannot able to share files between wireless devices.

  Please help me solve this problem. Wat could be the problem here. Stage of Wat I have to take to eliminate this problem.

  Advance thanks.

  Thank you and best regards,

  Chandhuru.M

  Hi, my name is Eric Moyers. I am a network Support Engineer in the Cisco Small Business Support Center. Please use the Forums to Post community of Cisco.

  The title of security without thread/how do you have isolation set up wireless?

  Insulation wireless (SSID) on the inside must be disabled to allow the computers associated with the same SSID to see and transfer files between them wireless

  Thank you

  Eric Moyers. : | :. : | :.

  Cisco Small Business U.S. STAC Advanced Support Engineer

  CCNA, CCNA-wireless

  866-606-1866.

  Mon - Fri 09:00 - 18:00 (UTC - 05:00)

  * Please rate the Post so other will know when an answer has been found.

• Satellite P875 - 32L - is unable to reconnect to the last connected WIFI access point

  I have a problem to reconnect to the last connected WLAN provider, with my Satellite P875 32 L.
  WLAN is switched on and shows all the neighbors access points, but it fails to whoever I logged before the reboot, or before you go to the rescue of the list.

  I'm going in service options for WLAN, sometiimes up to 5 times, then it undermines meet usually.
  It's well annoying.

  I have had this with the other 30 satellite of P870 too, but something so this behavior have disappeared. So there must be a solution.

  Hello

  You're talking about your private Wlan at home?
  If you had the same problem using another laptop too, it could be possible that this isn't a problem with the network s laptop wireless card or Wlan configuration but with the WLan router.

  You should definitely reset/reboot the rooter.
  In addition, check the settings of the IP router and or mac address filtering.
  Change also the type of encryption and Wlan channel.

  You have to try different combination turn off just to test the WiFi encryption and check if the laptop would connect to the Wlan open correctly.
  But the Wlan encryption must always be defined in order to avoid improper use of the Wlan access point.

• PS B110a - wireless configuration will fail if the network has multiple access points

  Photosmart B110a (CN245B) wireless AIO printer.

  I have several wireless access points using the same SSID to provide coverage over a large area. When you install the printer on the screen TouchSmart wireless installation fails. Print report reveals the following error:

  "More than one access point/router wireless was found which matches your network name (SSID). If this is not intended, your HP printer can connect to the wrong network. »

  In my case this IS planned but there seem to be no available option to answer "OK, just connect to any point of access by using my SSID.  If I turn off all but one the APs configuration complete OK. If I have to do every time I turn on the printer the printer is USELESS for me.

  Did I miss something?

  sijomi

  This should not be a problem.  I have a B110 (and another 10 or so HP wireless printers) on a network of airports with 5 access points and they just connect.

  Here are a few suggestions:

  1. don't use WEP - use WPA or WPA2 with a 13 + character password.

  2. enable the SSID broadcast on all access points

  3. do not use the MAC filtering acddress

  4. make sure "AP isolation" or "isolated wireless" is disabled.

  5. make sure that you are not on a private network, virtual, or connected to your network of comments.

  6. If different strings on access points do not work, try the same channel.

• Changing the E3200 as wireless access point

  Hi, I recently bought an E8350 router and have a spare E3200. How can I change E3200 as an another access point wireless to work with my new E8350? Thank you very much.

  You want to connect your E3200 to your new E8350? You can mount the two cascading, but I suggest you do the E8350 as your main router and connect the E3200 so that it will act as an access point. You can watch this video for you guide: http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=b946afd839aa48938783df77f009e155_Cascading_your_Li...

• DHCP option to set the controller IP for Access Points (Airespace)

  Hello world.

  Does anyone have an idea to specify the controller using DHCP options.

  We use:

  -Controller AIR-WLC4404-100-K9

  -AP-1010-AP-5312 poinst access

  -Server dhcp DHCPd ISC 3.0.1

  Newspapers on DHCP server indicates that access points become the IP addresses, but the controller information are not "read" / "included".

  In the productive environment, controllers will be redundant.

  So far, we couldn't sucsessful with eighter of these configurations:

  Block i. using VTL:

  http://www.Cisco.com/en/us/products/HW/wireless/ps430/products_quick_start09186a00805100f5.html#wp49287

  subnet 10.50.107.0 netmask 255.255.255.0 {}

  option subnet-mask 255.255.255.0;

  routers option 10.50.107.1;

  option domain-name-servers 10.20.51.11, 10.20.51.12;

  option vendor-class-identify Airespace 1200;

  the option dhcp-client-identifier 0xf1, 8, 10.20.51.254, 10.20.51.249;

  DDNS-updates

  DDNS-rev-domainname "in - addr.arpa.";

  DDNS-domain name "xxyy.local.";

  default-lease-time 28800;

  range 10.50.107.101 10.50.107.200;

  }

  II. using the DHCP Next-Server option:

  subnet 10.50.107.0 netmask 255.255.255.0 {}

  option subnet-mask 255.255.255.0;

  routers option 10.50.107.1;

  option domain-name-servers 10.20.51.11, 10.20.51.12;

  Next-server 10.20.51.254;

  III. use of Header Information Option 43 described such in DHCP Manual:

  WLAN-apc code 60 option = text;

  ip address wlan code option 43 = controller;

  subnet 10.50.107.0 netmask 255.255.255.0 {}

  option subnet-mask 255.255.255.0;

  routers option 10.50.107.1;

  option domain-name-servers 10.20.51.11, 10.20.51.12;

  option wlan-apc "Airespace.AP1200"

  option wlan controller - 10.20.51.254;

  IV. using header to the DHCP server information:

  class "-classes of suppliers ' {}

  vendor-class-identifier option match; }

  {"Airespace.AP1200" subclass "-classes of suppliers '}

  Next-server 10.20.51.254;

  }

  Does anyone have a working (using the SAI?) configuration or advice?

  Best regards

  Jarle Steffensen

  Yes, finally got it work.

  I just followed this guide:

  http://www.Cisco.com/univercd/CC/TD/doc/product/wireless/control/C44/DEP.PDF

  and it worked the first time :)