The connection between your access point, router or cable modem and the Internet is broken...

Similar Questions

• "The connection between your access point router or modem cable, and the internet is broken"

  It is a constant frustration for me sorce. My office gives me this error at least once per hour. I changed the wireless pci card (old one finally died but managed to stay in line!) to a usb dongle, and then to the diffenert pci card, and now I'm in a usb port, which is the same brand as the map oringal that worked. As it is, I can be online long enough to get hope and then... Poof nothing.  I do clean boots, refreshed earworm, did the whole ' IVF it ' was bound to him on a previous post, the netsh command reset. Nothing did. I know that's not the router because all other computers in the House including my laptop can connect.  What Miss me?

  Any help would be loved!

  Hey Tyler,

  Thanks for the reply and keeping the status updated. I appreciate the troubleshooting that you tried it on the computer.

  The issue could be a conflict of others on the computer.

  I suggest you to check the problem in Mode safe mode with networking:

  http://Windows.Microsoft.com/en-us/Windows/Start-computer-safe-mode#start-computer-safe-mode=Windows-7

  If you can't find the problem with Safe Mode with networking, I suggest you perform a clean boot on the computer and check with the question:

  I suggest you follow the link below to find out how to place the computer in a clean boot.

  https://support.Microsoft.com/kb/929135

  Note: Reset the computer in Normal mode once you have completed troubleshooting as a result of the "How to reset the computer to start normally after a boot minimum troubleshooting" section of this article.

  Just reply with the results. I'll be happy to help you.

• The connection between your cable modem, router or access point, and Internet are broken.

  What is the average message "the connection between your cable modum, router or access point, and internet are broken" and how to fix it?  We use internet provider time warner.  Can I access online using mini jetpack, but not through time warner.  Is the problem with our internet service or hardware problem?

  Hello Terri,

  Thanks for posting your question on the Microsoft community.

  Thank you for details on the issue.

  This problem may occur because of damaged or incorrect network settings.

  I would suggest trying the following methods and check if it helps.

  Method 1:
  Run the network troubleshooting and check.
  Reference:
  Using the troubleshooter from network in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  Note: You can run utilities times 'Internet connection' and 'network card'.

  If this does not help, use method 2.

  Method 2:
  Reset TCP/IP and check the issue.
  Refer to this article:
  How to reset TCP/IP using the NetShell utility
  https://support.Microsoft.com/en-us/KB/299357

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• Satellite A210-171 - unable to connect to any access point or router

  Hello. I don't know that this is the right forum. Not something I do normally but since I am desperate to solve this problem, I'll give it a shot.

  So I bought a Toshiba Satellite A210-171 nearly a year ago. It has a built-in wireless driver.

  The problem is, however, I can't seem to connect to any access point or router. What I end up getting most of the time are so a message saying that I am connected but with limited connectivity which means I can't access the internet. At other times, the network in range will appear in my network list, (with a signal strength excellent), but once I have select a message appears saying that the connection attempt has failed. And at other times my laptop detects the network connection and functions smoothly.

  I do not understand of course. So if someone could explain to me why my laptop selects and selects Wireless connections, that it connects and how I can solve this problem, I would be grateful!

  Thanks in advance

  Have you tried to update the driver on your laptop?
  Check the Toshiba site for an update:

  http://EU.computers.Toshiba-Europe.com > support & downloads-download drivers online

  And if you are already on this site check for a BIOS update.

• Power Save Polling (PSP) leads to problems in connection with some access points

  Symptoms:
  The following symptoms may be seen if an access point Wi - Fi (AP) or router Wi - Fi broadband does not properly support the Power Save Polling (PSP) feature:

  • Intermittent loss of Wi - Fi
  • Unable to open a connection Wi - Fi
  • Poor Wi - Fi connection data performance

  These symptoms may be more pronounced when on battery.

  Cause:
  The PSP mode is a feature that provides the long battery life for laptops. It requires coordination between the AP or router and the Wi - Fi adapter. Intel has discovered that some APs or routers may not implement the feature correctly or completely.

  Socorro

  Heard different things people try, depending on their wireless adapter.

  Start, control panel, device, netowrk, their adapter, power management Manager. Clear the checkbox to allow windows to turn off this device to save power

  Start, control panel, device, netowrk, their adapter, advanced management. Looking for antenna diversity. Some cards have it and others don't. Replace the Auto antenna by supply diversity

  Some have disabled Wireless N of their card and achieved good results.

  Some Wireless N adapters operate ONLY on the 2.4 GHz frequency.

  Using these parameters of the recommended wireless router I use channel 11, have GREAT results. I usually recommend creating a new SSID to make the connection easier. Wireless devices also needs to connect to the NEW network.

  Rick

• port high pass / low... connected on new access point...

  Hello

  I have 3500 Series switch and an Acess point LAP1242 connected on the interface of Gig... constantly of to newspapers showing the interface up and down... this never happened before... not able to get WEB access...

  any suggestions would be apreciated...

  HM...

  Hi harris,.

  The access point you're using is the AP LWAPP (LAP1242) this requires WLC... It will not work without the WLC... do you have one? If have you doner. then this behavious... should the PA will be in a loop until it registers to the WLC... and LWAPP == without Web access... only autonomous AP has access to GUI... I ask you to convert the AP using the below command...

  1 > download the stand-alone image from cisco.com

  2 > connect the cable from the console between the server of tftpd32 running PC and AP.

  3 > point image on the TFTPd32 server and make sure that you have connectivity AP to the laptop (same ip subnet)...

  Here are the steps.

  AP > en

  AP # debug lwapp console cli

  AP #conf t

  #int AP (config) FA 0

  AP(Config-if) #ip address 10.0.0.1 255.255.255.0

  AP(Config-if) #no close

  AP(Config-if) #end

  on the interface of portable fa give 10.0.0.2 24 and try ping 10.0.0.1 (you should be able to)

  then run the command

  Force - reload DOWNLOAD - AP #archive sw / overwrite tftp://10.0.0.2/

  for example...

  Archives/force-reload download-sw / overwrite tftp://10.0.0.2/c1240-k9w7-tar.124-21a.JY.tar

  This will do... I mean stop newspapers on the switch and also get WEB access...

  Let me know how this has answered your question...

  Concerning

  Surendra

• From high-speed wireless broadband with a cable modem, and shows the connection, but cannot access the web w / IE8

  I have Windows Vista, IE 8 and labtop HP Pavilion. I had just recently Cricket Wireless Broadband, with a USB wireless modem. I now have the Charter/Comcast broadband through my cable. The modem is connected to my PC via the Ethernet port. On the connection icon on the toolbar on the right down, it shows that I am connected. The "Local Area Connection Status" in the network and sharing Center seems to be connected, since bytes are sent and received.

  However, when I'm on IE8, it acts as if there is no connection. Not being able to view the web page. Also, now when I go to a local WiFi hotspot, I can't connect to a network, just as I always, and it shows that there is a link, however, it won't let me access the internet. It used to work, before everything first, I connected the cable modem.

  Any ideas? Thank you!!

  JFerguson15,

  If the Cricket connection works correctly but your cable connection is not, which suggests the computer is set up correctly and the problem is with the cable connection. All other systems are able to connect through the connection of the Charter? If this isn't the case, please contact Charter and see if they are able to determine the issue on their end or help you reconfigure the modem.

  Cody C
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• My programs that access the internet are broken

  It began without warning 2 days ago. Programs such as iTunes, Spotify, League of Legends and Razer Comms, immediately any accident by trying to connect to the internet. However, I have other programs that use also internet such as Call of Duty and Minecraft which work perfectly well. When I unplug my ethernet cable, all of the programs work very well. Connect to the top, the programs listed immediately freeze and close. I need help and will appreciate your answer.

  Help, please

  Hi Luke,.

  Do you receive an error message/code?

  I would ask you to do system restore and see if it helps:

  Reference:

  System restore

  http://Windows.Microsoft.com/en-in/Windows7/products/features/system-restore

  Note: When you perform the system restore to restore the computer to a previous state, programs and updates that you have installed are removed.
   
  Also, take note of the list of programs that would be affected information given by the system restore process, as one of these programs might be the cause of the problem.
   

  Hope this solves the problem. If the problem persists, you can write to us and we will be happy to help you further.

• OfficeJet J6450 - printer connects wireless but does not print job cable modem replacement

  Material: My printer is an OfficeJet J6450. I am running Windows Vista, current update.

  Probably triggering the event: I replaced my modem docsis 3.0 with a doscis 2.0 modem. PSI has remained the same. All other software and firewall remained the same.

  Dysfunction: After the replacement of cable modem, I found that I could print is no longer in my HP OfficeJet 6450. I would get an error in the printer window ' error - print. "  After the reboot after the publication of the initial error, I would get the error "error - sent to the printer.

  What I did:

  As a first step, I've uninstalled and reinstalled the HP software for the printer (complete package with exception of PhotoSmart and HP customer monitoring program).

  Use the connection for the network printer wizard, I entered the router password wireless to the printer. At first I don't have a connection. Then I rebooted the computer and the printer. I also returned to the default setting of network on the printer and repeated the configuration of the network. The connection was finally successful.

  The automatic test of the network page and the network printer wizard confirms the connection. Digital display of the printer and the HP diagnostic utility has also confirmed the connection. But the diagnostic utility is unable to print a test page and throw an error - "Print Test failed.

  The result disappointing:  I still can't anything to print wireless.

  ... Thanks in advance for your suggestions to get my printer back on...

  Go to start > Control Panel > printers and delete all instances of the printer.

  Then re-add the printer:

  1. make sure the printer is on and connected to your network. Verify that you can access the printer's internal web page by accessing its IP address before continuing.  Get IP address of a Test of Netowork wireless on the front of the printer (usually in the network menu).
  2. click on > start > Control Panel > printers.
  3. click on add a printer
  4. Select local printer
  5. Select create a new port and select Standard TCP/IP Port, and click Next.
  6. under device type, select TCP/IP Device. Under the name of host or IP address, enter the IP address of the printer. Click Next.
  7. Select Hewlett-Packard in the list of manufacturers and select and select your printer model. Click Next.
  If your printer model is not in the list, then select disk provided, browse the CD that came with your HP printer and select the first file begins with hp and ending with INF. click Open, then OK. Select your printer model. Click Next.
  8. If prompted, use the driver that is currently installed.
  9. He will ask the name of the printer - enter a new name or use the one existing. This will be the name of the printer that you select from other applications.
  10. we may ask you to share the printer. Choose No.
  11. the printing area of Test Page is displayed. Go ahead and print it out.
  12. click on finish.

• connect older apple Airport express with ethernet cable modem? Verizon service

  I'm helping someone with a verizon DSL modem older (guess this isn't wireless vs) which connects to a tower of Windows, then usb out of the tower to a unit of wireless to connect to a recent Mac laptop version. We would like to get rid of the tower and the verizon usb "hockey puck" and simply use the modwm > wireless Airport express > laptop.

  If I get an airport express, I can show the modem directly to Airport express?

  Yes, that should be fine.

  Tell us what model is the DSL modem.

  There are two possible configurations.

  Either the type pure or bridged modem and you use customer PPPOE over the WAN to the Express.

  Or

  You have a modem router and you will implement the express bridge, with creation of a wireless network.

  HOWEVER... I'm NOT either of those without call verizon and control on the price of a new wireless adsl router modem.

  ADSL has changed little in 10 years... but the equipment does not last forever. It could just be the perfect time to move.

• Problems with new cable modem and router

  Long story short, that my cable modem went bad.  I replaced it.  Now the two computers cannot connect to the internet.  It gives me a DNS error, saying that they can not find the server.  However, I can get on the internet if I hang the right modem to computer with courses through the router. I got it with the new modem a few days of work and use of the router, but now it does not work.

  There are 2 computers on the network, the two runnning vista.
  a linksys router model number BEFW11S4 ver 4.
  and the motorola surfboard SB5101 modem.  the old modem was a surfboard SB5100 motorcycle.

  There's a btn reset on the router (often the metal clip through a pin hole)
  Everything also its possible allways the router is bad

• HOWTO IOS upgrade the access point (router 881w) internal

  Hi experts,

  When I try to access the web interface of our new router from Cisco 881w internal AP, I get only a small button 'Enter', nothing more. When I click on this button, nothing happens. According to this thread (https://supportforums.cisco.com/thread/2003325) it seems that I should update IOS AP internal to this router.

  Now, my question is: How can I update the IOS of the internal HA?

  There are guides available?

  Thank you in advance for your help!

  Best regards, Matthias

  Sorry... the exact command is

  AP #archive download-sw/force-reload/crush tftp://192.168.0.168/ap801-k9w7-tar.124-21a.JY.tar

  There is no slash after crush...

  I would like to know how it works for you!

  Concerning

  Surendra

• I have a Palm Z22. It won't hotsync. It tries to connect, but then "problem, the connection between your device and the desktop could not be established. Please check your configuration and try again. »

  null

  Chillie wrote:
  Sorry I put my question in the wrong place.  I use Windows XP.  My Palm is a Z22.  I restarted my computer, if that's what you mean by a soft reset.  I have no answers-don't know my hot Sync Manager.

  A soft reset is performed on your computer Z22.  Look for the small "Reset" button on the back of the unit and press it with the tip of your pen or a paperclip.

  Reset draw your Palm.  Try to HotSync again.

  HotSync Manager is what your computer to connect to the computer Z22.  Do you see the HotSync icon in the lower tool bar?  If this isn't the case, you can not connect.  Go here:

  Start Manager button / all programs/Palm/HotSync.  This selection must load the HotSync Manager.

  I would help you with HotSync Manager, but you neglected to answer my question on "What version of Palm Desktop?"

  WyreNut

• Error IRQL_NOT_LESS_THAN_OR_EQUAL when I try to connect to wireless access points

  I get this error IRQL_NOT_LESS_THAN_OR_EQUAL whenever my wireless adapter is turned on or I re - enable after I disabled it to stop the BSOD happen at startup.

  Here are the scenarios in which it happens:
  (1) when I turn on the laptop and the wireless adapter is enabled; It gives the blue screen and restarts.
  (2) once it has been restarted since the first scenario, I have trying to move from a point of wireless access to the other.
  (3) the wireless adapter was disabled before closing, when I turn on a connection attempt, but it shows all the available connections and I try to solve problems, blue screen back again.

  Other information:
  I do not have any material change. I use the Windows 8 operating system. I use the HP Envy m4.

  Also, when it starts later, my screen remains black at any time from 1 to 5 minutes.

  I find that I use my PC because of the frustration of the far less.

  EF

  These accidents were related to the corruption of memory (probably caused by Kaspersky).

  Run these two tests to check your memory and find which driver is causing the problem.  Launch auditor.  You need not run memtest again unless you want to.

  If you are overclocking anything reset by default before running these tests.
  In other words STOP! If you don't know what it means that you're probably not  
  
  
  
  
  1-Driver Verifier (for full instructions, see our wiki here)
  
  2-Memtest. (You can learn more about running memtest here)

  
  

• Create odbc connection between local access and remote access or sql remote

  I need to connect to a remote access or sql database using my local in access 2007 version.  I can't understand what I put in each of the available boxes.  I see only a SQL driver to the system section of the odbc Wizard.  If I decide that he wants to know where the sql server is... well, it's not local, I have a web address for this and may not know how to get the systΦme can recognize the information remotely.  Help, please!

  Means of access:

  http://answers.Microsoft.com/en-us/Office/default.aspx

  Office at the above link forums

  http://social.answers.Microsoft.com/forums/en-us/addbuz

  Access support at the link above.

  They will help you with your questions of access when repost you in the Office Forums above.

  See you soon.

  Mick Murphy - Microsoft partner