With the HP G7000 laptop screen problem

Similar Questions

• the hp G42 laptop screen problem

  Hello.  I have a notebook hp g42 I can't see the screen-he made an entry and goes, then - it seemed to me that he will return when the outside frame of the computer has been adjusted, but that is not the case, more... I see a slight insight of what is supposed to be there with lines through it - mostly gray and the variations of gray-, but cannot use the computer - can't see it well enough to use it... and miss me it!  Any advice?  and thank you very much!

  I really doubt that it's a virus. It looks more like a hardware problem with the LCD screen.

• Why the Satellite L300 laptop screen stays white?

  Why the Satellite L300 laptop screen stays white?

  Hello, I have a Toshiba Satellite L300-29U over purchase, turn when he was first an hour about it looks a whole without problems, then the screen was blank. Feed again in a couple of times more hours after rest and passes him still takes some time to operate.

  What is your recommendation?

  Thank you for your response.

  Post edited by: Sams

  Hello

  Why?
  Who knows what have you that your screen is white?
  My screen is not white it shows everything correctly.

  The same white screen will appear on the external monitor?
  If so, then this problem may be related to faulty graphics card, if no, your laptop computer s display can be defective

• Problem with the resolution of my screen after installing Windows on my ASUS laptop K51AE 8.1.

  At first I used the Windows 7 operating system before you download and install the student version of Windows 8 on my ASUS K51AE track. I fully configured my laptop with the new software setting with my own parameters before noticing that everything on the screen seemed very pixelated operation and large, in order to solve the problem, I tried improving the resolution to something higher up on the list but unfortunately I was not given another option to go to. The laptop is locked for the resolution of 1024 x 768 when I used the resolution of 1920 x 1080 front on Windows 7. I'm still not able to click / tap on the option of the current setting of 1024 x 768, I don't know why this is happening? Please ask help?

  Hello

  You must download and install the latest graphic drivers of Windows 8/8.1 ASUS for your machine, as it has been defined for Windows 7.

  If none are available, you will need to upgrade, if you can, your graphics hardware to solve the problem.

  Normally, you would have embedded chart that you can not change

  ASUS:

  http://www.ASUS.com/support

  See you soon.

• HP computer laptop-15-be002tu: display in a new laptop screen problem

  Dear friends,

  I bought a new laptop from hp [hp-15-be002tu]. It is provided with the operating system of back free v.2.

  When I tried to start my laptop by pressing power button there is no display on the screen. But I waited for 5 minutes. The HDD & dvd player work properly.

  But I noticed screen does not work. How can I solve my problem?

  Please give good soggestions to fix my problem

  Thank you all

  Dear friends,

  My display problem has been resolved.                                                                                                                                                                         An HP service technician visited my house [on-site warranty] and inspected my computer hp laptop and found that a video cable from the lcd screen was not correctly set. This is why there is no display on the screen of my computer hp laptop.

  I asked him why he came... It is due to either by transportation [services of e-mail... etc.] or manufacturing unit.

  In any case, my problem has been resolved.

  Thanks for the HP amicable services team

  M.Ganesh kumar

• I AM USING WITH MY HP DV9500/9650US screen problem READ FOR more DETAILS

  I thought that posting this here because my response was the way down on page 63 of the original post for those of us with problems screen with dv9500/9600 models.  Mine has 2 stickers, 9500 and 9650u, so I don't know who to call, that did not matter because I have had contact with the best guy, as far as I am concerned HP!  Mathew Camden offered a solution that I could live with and not let me for the full price of the repairs.  In addition, I got a full extended warranty for a year!  Slow to come, but I could tell that Mathew "has me" when I tried to explain what is happening here.  Apparently, HE's the guy (or one of) talk while HP understands that there is a big problem.  I give more information on how to get help below.  The drop box must be here in 2 days.  I am happy that I was seriously looking at new laptops.  My thought was that Dell has some laptops starting at $ 500 and, although not as nice as the model that we have, at least, it would be in working condition.  Not that I want to spend this money right now, but I was running short of choice.  I'm happy that I don't have a car, the truth is, I LIKE really this laptop until he started running slow and finally 'crapped' as my husband says.

  "Ok, I had some success.  I hope this helps the rest of you.  Here is what happened:

  First of all, I called 1-866-671-7362.  No good resolution.  Was transferred to the "Mark", who refused to give me any help or even transfer me to anyone who could possibly.  He kept repeating that my laptop was out of warranty.  Well, I know that, we all do!  I told him about what was happening on this forum, and he continued to be indifferent to issues that these customers have.  I called back, thinking I could get a new person.  I asked to speak with a case manager once again, I specifically said the person that I didn't "Mark" once again because the conversation was not good.  Well, guess who I had once again, "Mark."  You don't have to bother with them, he does not support it.  I don't think that the Center to this number is still here in the USA, but in India, it's why THEY don't CARE, that many find.

  After some research, I called 1-800-756-0608, option 7.  They ARE in the custody of the United States and ILS DON'T.  I was greeted by a very nice lady, I forgot her name but she was in the Executive Service.  I was transferred to Mathew Camden and he HELPED me!  I told her about this forum and everyone here having the same problem right about 18 months after the purchase.  He presented a very reasonable and fair offer.  He offered to sell me an extended warranty for a total of $162,29 and then dealt with a free repair under this warranty.  This warranty is for 1 full year.  I am satisfied.  If only I had taken this answer at first.  It took me over a month to get the right answer, but I'm glad that I stuck to it.  Because I have a full warranty for one year from today, I am happy with the price tag of $162,29.  If she died this year here, I can get it fixed.  It covers ANY matter coming more than telephone support!

  Apparently, you must be able to get to the right person.  Problem is that people of "other number" don't give me that information and I felt "stuck" and extremely frustrated, angry to be honest.  I guess this is my next question, how the average person knows "good number" to get their issue handled.  Fortunately, I came across it.  I'm writing it here for all people in the same situation to get help.

  MATHEW THANKS! He gave me his direct number and let me know he will personally supervise this repair and make sure that it goes as it should!  It does not help redeem HP slightly.  HP is a great company and it's just a guy.  To bad, they no longer have 'Matthews' at the end of the phone.  I'll just make sure to cling to this department number, in case I decide to buy HP in the future.  Wow, what a difference a single appeal filed. »

  Message edited by mommaK 07/28/2009 23:52
  K

  Great to hear that you have a resolution! I hope that others will benefit from your sharing of this experience.

• I had a start of the computer, but black screen problem. Now resolved, but have a question.

  Hi, a question for the tech support.
  
  My solution ended up having to remove a faulty RAM stick. Fortunately, I had two, one of whom was a 2 GB key and that went wrong was 1 GB. Whenever this faulty stick has been in the laptop, the system wouldn't start.
  
  The problem is now resolved after removing the defective RAM 1 GB stick.
  
  In any case, I was wondering on a stick of RAM that turns bad in this way.
  
  First question is, how are they just bad like that?
  
  Second question, can they be fixed all or none of the trash can right RAM sticks after that?

  Hello feroxlara,

  I see that you have any questions about RAM, is that correct?

  The answer to your first question is that there are several things that can cause a memory stick to stop working or become defective. It may be overheating, overvoltage, problems with the RAM itself, problems with the slot in the motherboard memory is underway and many more. It is a component which may fail on any system.

  As far as being able to set the memory for the average person it is not likely, here is a link to an article on the repair of RAM. He explains what would be necessary to fix a memory module and in most cases, it is easier to buy a new stick of RAM.

• computer laptop screen problems

  I started to have narrow lines from top to bottom on the right side of my screen

  Hello

   

  Yes, the question doesn't seem to be with the material. You can check if the monitor works properly on another computer or try to connect to another monitor to the computer and check.

   

  If the problem persists better option would be to contact the manufacturer for assistance and check.

   

  I hope this helps.

• HP 2007 w/XP computer paired with the new HP flat screen - Image distortion

  Old computer with new flat screen monitor: how to set display and the image is normal looking as opposed to tense? I see the adjustment on Vista is it possible to do the same thing on XP?  Thank you!

  Hello

  Sounds like a screen resolution problem...

  • Click with the right button on a part empty your desktop, and then click Properties
  • Click on the settings tab
  • Move the resolution slider all the way to the right
  • It should choose the native resolution of your monitor
  • Click OK

  The native resolution of your screen are not selectable based on the ability of your graphics drivers. Updated drivers may solve this problem, but perhaps also that it will not.

  Tricky

• Cannot install Vista service pack 2 is 800f0a09 error code with the message that there are problems with the driver for dell latitude

  Original title: why I get error code 800f0a09 to upgrade to windows vista service pack 2

  I have a laptop del that is running on Windows Vista Edition Home Premium. I tried to download itunes but it requires service pack 2. Whenever I try to update to service pack 2, I get the message following error code 800F0A09. He also mentioned problems with the driver for dell latitude. What can I do to fix this please.

  Thank you

  Hello

  Please join Microsoft Community where you can find the necessary information on Microsoft products!

  You can not install Vista Service pack 2 and get the error with code 800f0a09 and the message that there are problems with the driver for dell latitude.

  The problem may occur if some of the components of the update are corrupt.

  What is the full error message that you receive?

  I suggest you follow the steps mentioned below to check if the problem is with the update components:

  Method 1: Reset the update components

  See the site:

  How to reset the Windows Update components?

  http://support.Microsoft.com/kb/971058

  Warning: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry

  Method 2: Run the system update readiness tool

   

  See the site:

  System update scan tool corrects errors of Windows Update in Windows 8, Windows 7, Windows Vista, Windows Server 2008 R2 and Windows Server 2008

  http://support.Microsoft.com/kb/947821

  Method 3: Turn off the antivirus software

   

  See the site:

  Disable the anti-virus software

  http://Windows.Microsoft.com/en-in/Windows-Vista/disable-antivirus-software

  Important note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  I hope this helps. If the problem persists, let know us and we would be happy to help you.

• Connection with the client VPN for RV110W problem

  Hi guys: I just installed a RV110W router to my small business and I try to connect via VPN from home client.  I was unable to do so, no matter what I try.  Relevant information:

  1. I can connect to the router via remote very well management, so I know that the router is accessible from the Net.

  2. internal address of the router: 10.81.208.1

  3. active PPTP.  PPTP server IP address: 10.0.0.1

  4 IP addresses for PPTP clients: 10.0.0.10 - 14

  5. two VPN clients added - one with PPTP, with the QuickVPN Protocol Protocol.  Both are enabled (and Yes, I triple checked passwords)

  6 encryption MPPE and Netbios active.

  7 IPSec, PPTP and L2TP all active gateways.

  8 VPN client: 1.4.1.2

  9. computer: laptop running Windows 7 family (64-bit), with the firewall Windows is activated.

  10 home network: 192.168.2.196

  It is causing to tear my hair out.  What Miss me?

  Shannon

  Hi Shannon,

  I am pleased to see that you're progress.

  Shannon Rotz wrote:
  I changed the RM port to 443.  Unfortunately, now I can't connect to the router via browser, either by remote management or from the local network - I get the usual "page cannot be displayed".  How do I get back into the router configuration GUI?
  

  You should be able to reach the GUI by typing https://192.168.1.1(assuming that you have not changed the default IP address) normally once you replace http (port 80) with https (port 443) the internal router web server automatically will redirect you to the https page if you type http. Open your command prompt and try to do a ping of the IP address of the router to ensure that it still meets this address

  With regards to the VPN client:   Up until I changed the port, the same error message kept coming up, i.e. "Unable to establish connection" (or something like that), with a list of possible reasons why it couldn't connect. Now the message has changed - I'm getting "Server's certificate doesn't exist on your local computer".  If I continue trying to connect, then it says "Activating Policy", followed by "Verifying Network", then "The remote gateway is not responding.  Do you want to wait?"  This is definitely progress, since I never got this far before.

  You are a quarter inch offline. If you look at the log.txt in C:\Program Cisco Small Business\QuickVPN Client, in my view, you will see "Failed to ping router remote VPN! This means that your PC is blocking the ping to the router response. Usually, if you look at this point the status of Client VPN in the router (first of all need to remote management) you will see that your user status is "connected." If the router thinks that the connection is established, but the PC does not work. You might want to try another PC at this stage to verify that it is indeed a problem with your PC. This problem is usually caused by the 3rd party software antivirus/firewall blocking the ping response. Microsoft Security Essentials can do this as well, so if you turn it off. If you do not have another PC to test from, call Cisco Small Business Support and ask a technician, try to connect to the lab. You can find the number to call here

  On an impulse, I tried setting up a Windows VPN connection, i.e. created a new VPN connection in Network and Sharing Center, using a PPTP client ID that I had created.  That connection actually worked, except for one problem:  I can't see the remote network.  If I could solve that problem, I'll just tell the other clients to use a Windows connection rather than QuickVPN.
  

  Good thought. If you do not see the remote devices, make sure that they do not block VPN connections. (Windows or third-party firewall, antivirus, antispyware) With a connection, PPTP or QuickVPN, you should be able to go to run, type the IP address of the device that you want to connect to (i.e. \\192.168.1.101 ) and see the list of shared folders. After the PPTP connection is established, try to ping the address LAN IP of the router. If it is successful, try to ping a LAN device such as a network printer or a PC. Again, PCs may block ping requests if they have a firewall running watch so for this.

  Answer please if you have any questions.

• Unable to work with the camera on laptop

  Original title: camera

  my camera on my laptop does not work.

  It works through skyping, but I want to take pictures and do the videoes but his does not work

  Hi r.,

  Please answer a few questions to refine the question.

  1. are you referring to photo App? What is the situation when you launch photo App?

  2. do you receive any error messages?

  3. What is the brand and model of the laptop?

  As you said that you were able to work with the camera when using Skype app, there is a problem with the permission of the camera app to use the construction in camera.

  If the camera application opens, then follow the steps mentioned below:

  a. press Windows + C on your keyboard to open the bar of charms.
  b. Select the settings option.
  c. Select permissions .
  d. snap it allow this application to access to your: Webcam and Microphone option.
  e. close the application by pressing Alt + F4 on your keyboard.
  f. open the camera app and check the results.

  If the problem persists, then I suggest you to run Windows 8 Troubleshooting App to diagnose and resolve the problem.

  Hope this information helps.

• better integration with the Mavericks. Still a problem with the display of the menu bar spaces when moved

  Much better integration with the OSX mavericks on the latest version. Without a doubt ahead of Parallels in terms of dual display/full screen. The menu bar has been resolved, but there is a ghost menu bar that appears when you move one space (fullscreen vm) from one monitor to the other. It resembles a translucent bar on top and without words. But clicking on it shows menus as if it is supposed to be links there.

  Yes, it is a known problem with the Mavericks Developer Preview; We work closely with Apple to find a solution. So far, we have seen only with the restoration of the window or when you move the window between monitors - if you leave full screen and enter again, it should work fine. If you notice any others, please let us know.

• PS is ready for the high-resolution laptop screens?

  I am considering buying Dell Precision M3800 but the I'm really worried that it will not be usable for the PS

  Were there no improvement in this issue?

  Photoshop CS6 won't scale and will not be patched to the scale. Only CC 2014 has 200% adjustment so that you can read on the laptop M3800 interface.

  CC of Photoshop (14 v) don't be. CC 2014 (v15) will be.

  I'm not familiar with other programs in CS6, so consider in their respective forums.

  The other bad news is that you see in your old laptop to 100% of the files will appear half size on a screen high resolution. So I don't know how users M3800 get around that.

  A recent update: Photoshop: introduction to scale the UI 200% for screens high densities for Windows

  You should join this thread if you have any other questions. Chris Cox is the main programmer for Photoshop.

  Gene

• With the new update my screen is not wide enough for the format. How can I change this?

  After the new update, the display shows only 3/4 of what is presented. I reduced the size of the print and that did not help. For example, typing this, once I had as "present" the due screen move to the left to allow me to see what I was typing. It does this automatically. I don't know what caused it in the latest edition of the update, but he made me a certain number of problems by acting on the Bank of line because no moveable windows do not show enough to allow me to hit the submit button.

  I want to see the whole window when I log onto a site. When I open now Yahoo News, for example, I don't see the last of three inches. I can see them if I hover over the page, but until now, I always saw the entire page when it comes to the top without having to take any action on my part.

  Where can I or how can I do to get it to how she still worked before?

  I opened the learning system and it refers to a tool of Mozilla bar which I did not either. Don't know if it of relevant or not.

  Hello

  Firefox on Windows is now after display, scaling options that can make the biggest text on screens at high resolution. There are several ways to solve this problem. See the Web pages are broad and fuzzy after update of Firefox - how to fix article for a suggestion. Here is another possible solution:

  • Type of topic: config in the Firefox address bar and hit the Enter key.
  • If the warning that this might void your warranty , click I'll be careful, I promised.
  • Search for layout.css.devPixelsPerPx

  

  • Double-click layout.css.devPixelsPerPx to edit its value. The default value is - 1.0 in Firefox 22 and above. Change it to 1.0 to run as in previous versions of Firefox.

  If necessary, further adjust the value of 0.1 or 0.05. Values between 1.0 and around 0.5 to reduce the size of the elements. Use a value greater than 1.0 to increase the size. For example, a value of 1.25 will increase the font size of the 125% to account for the default DPI setting in Windows 8. Check the value that you enter. Definition of a value that is too small will take everything away and too high will explode things.

  If the web pages should always be adjusted so you can watch the extension Default FullZoom Level or NoSquint .

  To adjust the font size for the user interface, you can use the extension of theme font & size changer .

  This solve your problems? Please report to us!

  Thank you.