Similar Questions

• The connection failure module 9795 with wsn-3226 with Labview 2012

  Good afternoon

  I have a Crio-9074, with a 9795 module and two modules WSN-3226 and I have updated my Labview to the latest version, version 2012 and me cannot communicate with WSN nodes. The program says that the nodes cannot connect with the gateway. The software I have installed is:

  -Labview 2012

  NOR-Rio 12.0

  NOR-WSN 1.4

  -OR-Real-Time Module 2012

  I checked CRio don't let install WSN host API 1.4.0 because it is not installed in my host. Can someone tell me where I can download it, and if this is the reason why I can't communicate with nodes?

  Thank you for your time

  Hello

  I have

  LaurentV wrote:

  Hello

  Make your cRIO and all modules appear in MAX?

  Could you give more details about the problem, such as a screenshot of instructions on how to reproduce the problem, and you get the error message?

  ---

  Lawrence V.

  Engineering Application OR (France)

  correction of the error, by reinstalling Labview 2012. Thank you very much for your attention.

• Portege A600 - lack of temperature probes in Everest and overheating

  I have 2 identical A600.
  On of them display 6 temperature sensors - for example on Everest
  Processor
  Base 1
  Core 2
  GMCH1
  GMCH2
  Hard drive

  On the second:
  Processor
  Core1
  Intel Core 2 processor
  Hard drive

  Tip:
  the other is overheating, always above 80 ° C (the fisrt under 60) and hangs sometimes seemingly on the side of temperature.

  Thanks for help

  Hello

  I put t believe these tools 3rd party, but if your laptop is overheating and stops, you should clean using compressed air stream. This could blow out the dust from the cooling fans.

  Also, make sure that you use the latest version of the BIOS. You can download it on the Toshiba site.

  Good luck! :)

• A temperature probe is really necessary for the replacement of the hard drive?

  I replaced the hard drive in my late 2009 iMac 21.5 ". In the OWC video, he calls for a probe. My hard drive is not one of the built-in ones. I was wondering if I really need or the computer will work fine without it?

  Well without it your HD fan will be clocked at high speed all the time. The good news is that you can also control the fans/temp via the software. Here is a free software that works very well. http://www.eidac.de/

• Build the executable with WSN

  Salvation OR engineers,

  How can I deploy the WSN library in an executable file?

  Thanks in advance,

  Luiz

  OLA SR. Luiz.

  Neste caso, Bivvy instalar o also pilot NI WSN no wave maintains .exe will be used e o computador não fazer o Chipre will deploy das variaveis, POIS elas sao published pelo Gateway automatically.

  Caso o senhor não possua o instalador do pilot, por favor, acesse o link abaixo e faca o download do mesmo.

  http://Joule.NI.com/nidu/CDs/view/p/ID/2158/lang/en

  Single also o modulo NI WSN pioneer não precisa ser taboo para this type of application.

  Beneficial has will para contactar em caso amendments of other questions.

  Atenciosamente.

  Hello, Mr. Luiz.

  In this case, try to install the driver of WSN in the PC that will serve as the .exe file. If you do not have the driver installation program and won't be not necessary do the deployment because the variables are automatically published by the gateway.

  Please, use the link below to download the driver.

  http://Joule.NI.com/nidu/CDs/view/p/ID/2158/lang/en

  Feel free to contact us for any question you may have.

  Sincerely.

• z820: suspect z820 temperature probe causing one of the two processors to misbehave

  I'm running a double z820, who became very strong.

  I ran the HWMonitor and HP Performance Advisor for the diagnostics on the system and found some interesting things:

  1. The system thinks that CPU 1 is running at 92 degrees Celsius. And CPU 0 is on average about 35 ° C.  When I opened the case and check it out.  CPU 1 is actually cold to the touch.
  2. CPU 1 fan spin at about 4900, while CPU 0 fan is walking to 1100.
  3. Clock speed of the CPU 1 is locked to 1.1 Ghz.  CPU 0 is running to his good 3.5 GHZ

  So my conclusion is that the system is badly interpret the CPU temperature, CPU 1 fan to hyperspeed and ratchet down the clock of the CPU speed to try to protect against overheating.

  Oh, and if I'm not running something that causes the system to try and use all procs on two processors, the system stops.

  Overall, I currently have a workstation hard, running barely answer half speed and intermittently closed - which is unproductive and boring.

  -If my assessment is healthy, my question is: where to look to find the thermostat for CPU 1 so that I can either replace, or maybe the cable must simply be re-allocation of places.

  Any ideas would be fantastic.

  Problem solved.

  Coolant replacement brought to form normal and the machine is quiet and cool operation.

• How to use the kit sensor Bioinstrumentation Vernier with NI ELVIS II and LABview on a CPU?

  So I have the NI ELVIS II + and a box full of Bioinstrumentation sensor, including Kit sensors: Analog Proto board connector (s), pressure sensor, hand dynamometer, hand grip monitor heart rate, EKG sensors, Surface temperature probe, among others.

  I can't seem to get all the sensor data to my PC that I use, I'm not too familiar with electrical circuits but I followed the manual directions for the specific sensor but it seems as if it doesn't have a difference. I'm with copper son crochet and so that they know the places appropriate (according to the manual) but nothing.

  Am I missing something? I have also the is open regardless of the specific LABview laboratory (Surface Temp lab for example), but when I press run it is as the sensors are not recognized or even be recognized. The sensors are plugged into the connectors on the analog Proto Board also. What I am doing wrong, and how can I get these sensors to work?

  Any help will be greatly appreciated.

  From what I see, it looks like a typing mistake in the manual.

  Try to connect GND AI0 - and NOT ALWAYS.

  It should look like this.

  Connect the following pins for wire connector:

  1. AI0 + SIG1 analog connector Proto Board

  2. + 5V power supply DC to 5V analog Proto card connector

  3. Power supply to the GROUND to GND of the analog Proto board connector

  4. AI0 - GND of the analog connector Proto Board

• WSN-3212 or NI WSN 3202 when loaded with VI target with

  WSN-3212 or NI WSN 3202 when loaded with a new firmware using option "Add LABView WSN target", cannot re connect with the gateway ethernet OR WSN - 9791. In MAX, the quality of the link state is "lost Signal".

  Basically, I tried to change the sampling in the sample interval ""case structure, then built the VI and deployed on two WSN nodes. " They show the status of the download of the firmware and the LABView also shows the message 'successfully deployed", but then, knots just to start scanning and never connect again.

  Please help in this regard.

  Hello binarystar105,

  When you have downloaded the new firmware, did you follow the steps described in this article?

  How to upgrade the Firmware on my NI WSN gateway?

  http://digital.NI.com/public.nsf/allkb/CF6241F5F849FC7086257909008327C5?OpenDocument

  Also, what version of firmware you currently have?

  What version of the LabVIEW WSN Module work?

  If you look at the properties of the node of your window from the LabVIEW Project Explorer, can set you the tab node sampling interval?

  You may already familiar with this material, but I found the following white paper to be extremely useful when I started working with WSN:

  Getting started with wireless sensor networks of NOR

  http://www.NI.com/white-paper/8890/en/

• How to use the probe PT 1000 with NI 9211

  Hi all

  How to use a PT 1000 with NI 9211 temperature sensor?

  I am currently using Signal Express, just try to measure the temperature, but so far with no success

  THX in advance,

  Lasse

  A NI 9211 is a thermocouple device I.  A PT 1000 is an RTD.  While it might be possible to signal conditioning to get this to work, you're better off:

  Purchase of a thermocouple to replace the PT 1000

  Or buy a NI 9217 (RTD module) to replace the NI 9211

• Advise on the maintenance of low temperatures with AMD TurionX2

  Hello

  I decided to sacrifice some performance for the sake of cool temperatures and quiet fan. I have HP DV6, with AMD Turion RM-74 and HD4650.

  So, Yes, you'll lose upward to the power of your CPU to 15 percent, but heyh, this processor is so fast that you won't be barelly opinion change. You will have always contained HD watch with 720 p and all the rest gently. Note that game will part more difficult, but consider your laptop not as a device created for the heavy game.

  At one time or another, during games, one day your laptop colapse inevitable. It is simply not intended for games, what are the specs...

  So, how to reduce your cell phone time:

  (i) power options-> several power supply options,

  (ii) balanced diet-> change the settings.

  (iii) change advanced power settings

  (iv) processor-> processor power management state Maximum-> on battery - 50 percent, Plugged in French - 85 percent.

  (vi) save changes and close.

  
  

  Now, my temperatures are - slowed 48, heavy load - 57, extremelly heavy load (HD 720 p content) - 62-63. (Now my the CPU cores are at 47 degrees celsius).
  

  CPU always runs fast, not so fast that it works on 100%, but well, fan is quiet and if you want games - go to your desktop pc, let laptop to lighter, although the specifications of the laptops are high.

  simply, it can't handle the heat.

  Best regards.

  Make it easier for others to find solutions, marking my answer to "Accept as Solution", if it solves your problem.
  Click on the BLUE CONGRATULATIONS button on the left to say 'thank you '.

  Hey, even better:

  I have increased the status of the Maximum processor at 99 percent. So, I lost the power of CPU of 1 percent,

  and with the same temperatures - LOW temperature. So, try yourselves.

• Fan noisy and slow speed for the Macbook Air with 10.11.4

  I hope you can help me.

  I upgraded 10.11.4 on my Macbook Air a couple of days. It is a model of 2013 Mid, 1.7 Ghz Core i7, 8 GB of RAM.

  I don't know exactly what my last update was - but was El Capitan any.

  I tried LANDAU and SMC resets.

  Previously, she has chugged along fine. The fan was quiet most of the time - only hit on when I used Lightroom.

  Now, the fan kicks on regularly, most of the time actually. And it's MUCH slower. Very lag sometimes when you type in Wordpress, for example. And lightroom is much slower. Also, when I use FaceTime, video often turns itself on and off--with a message informing me that it will resume when the computer cools down. Yet the back of the computer does feel not hot at all.

  I tried page of Chrome in Safari. Doesn't seem to help much.

  I am currently traveling to the Peru and did not my hard drive with my last backup, Time Machine, by hand, so as I understand it, I can't go back to a previous update.

  The Kernal task often seems to have a very high CPU %: 250 or.

  Right now, I'm trying to download the Combo, I read that this can sometimes fix glitches.

  Any help is greatly appreciated!

  The kernel uses excessive CPU cycles. Here are a few possible causes for the State. Some may not apply to you.

  FileVault

  Please, open the security and privacy pane in system preferences and click the FileVault tab. If there is an indication that the encryption or decryption is in progress, wait (possibly several hours) so he can finish and see if there is an improvement.

  Limitation of the

  When he does readings of high temperature in the material, or a MacBook battery low voltage readings, the kernel can try to compensate by interrupting the processor to slow them down and reduce energy consumption. This condition may be due to:

  ☞ an accumulation of dust on the logic board

  High ambient temperature ☞

  ☞ a defective battery or worn in a laptop

  ☞ the malfunction of a cooling fan, temperature probe, a probe or some other component voltage internal

  Note that if the problem is caused by a sensor, there can be no real overheating or undervoltage.

  If the computer is portable, try with and without the power adapter connected. If pigs kernel_task processor only on current alternative, load is causing the machine to heat up. This behavior may be normal for some models, but it can also be an indication of a hardware failure.

  Apple diagnostics or the Apple Hardware Test, although not very reliable, is sometimes able to detect a fault. For more in-depth material test, an appointment of 'Genius' to an Apple Store, or go to an other authorized service provider.

  If all goes well with the material, then everything that you can do to improve the cooling can help.

  Software installed

  The software installed by the user which includes a device driver or other kernel code can thrash of the kernel. This category includes virtualization, such as Parallels and VMware software, as well as products 'anti-virus' more commercial. Some system monitoring applications, like "iStat", may also contribute to the problem. You can test this possibility to completely disable or remove the software according to the instructions of the developer or start in safe mode. However, it should be noted that the deactivation of a modification of the system without removing or test in safe mode is not as easy as you think.

  Corrupt NVRAM or MSC data

  Sometimes, the problem is cleared up by resetting NVRAM memory or MSC.

  External display

  Connect an external display to some models of MacBook Pro while the lid is open can cause this problem. If necessary, use the external clamshell modescreen.

  Other devices

  Disconnect devices wired everything except those needed at startup and remove all the expansion cards of third parties (if your model.) If the problem is resolved, reconnecting devices one by one by one until you identify the culprit.

• PID control with big delay in the process variable

  Hello

  My goal is to control the temperature via a valve and heat exchanger. I proceeded variable (temperature) measured from a hose. This temperature should be raised a few degrees with a heat exchanger. So basically I need to order a valve that allows the water to flow through the heat exchanger to raise the temperature to the desired level.

  My original plan was to use a base PID regulation to operate the dispenser. However, it is about 0.5 to 1 minute of delay time in the temperature probe after I opened the valve, which increases the temperature. This leads to a situation where the PID regulation valve fully open during this period (trying to get the temperature rise). Then once the temperature begins to rise it fires quite quickly. PID begins turning the tap off almost immediately, but because of the time delay in the sensor, the temperature exceeds seriously. This led to severe oscillation and at worst unstable processes. I tried to adjust the PID control to "predict" the timer to close the valve in advance to minimize the excess, but failed.

  I would appreciate if anyone has any ideas how to make this type of control with Labview PID functions. I also wonder if there is a better type of control procedure for this scenario as a PID control?

  -Lars

  This is a very common situation in the heating control, and generally PID can be adjusted to make it work. How do you do the tuning? If you do it by trial and errors, you have little chance to succeed. For a slow process with time delay, I like to use the method Cohen Coons, or similar open Ziegler-Nichols-loop method. The idea is that you temporarily remove or disable the PID. Set the valve in a fixed position and wait for the temperature to stabilize. Then, change the setting of the valve and record temperature at regular intervals data until the temperature is stable again to a new value. Use these data to get the initial values of PID using the equations provided by the tuning method you choose.

• The REPORT CYCLIQUE with myDAQ measure?

  Hi all

  Sorry for my beginner question. Is it possible to measure the duty cycle with myDAQ? If Yes, could you give me some advice please how? I want to measure the temperature with temperature probe SMT 160-30 with duty cycle output.  I tried the analog and digital inputs. In the case of the analog input, there is a problem with zero amplitude (error). If I use entry digital then output is 0 and Boolean variable 1 and I don't know how to proceed with the determination of the duty cycle. I use DAQ assistant so I will gratefull for the solution with the DAQ assistant.

  Thank you very much

  Pavel

  What you need to do, is to capture a waveform analog (PWM signal).  Then you perform a comparison on all data entered to see if it is greater than a threshold.  A typical threshold for a 5V signal is 2.5V.  That should translate into an array of Boolean.  Use then Boolean (0.1) followed by the average.  If you want a percentage, multiply by 100.

• Blue screen on startup... problem with the display driver?

  I have been using a Dell Inspiron 14R (N4110) laptop computer since 2010 without any problem.

  The laptop was purchased online from Dell and came with

  (1) Windows 7 Home Premium 64-bit and

  2) AMD Radeon HD 6470 M - 1 GB display card.

  Recently, I had a problem where my laptop just wouldn't start, showing the blue screen every time it tries to start. The blue screen mentions a problem with the file atikmpag.sys I understand is the driver for the AMD video card.

  If I delete/rename the files atikmpag.sys and atikmdag.sys (via secure boot mode) in C:/windows/system32/drivers, the laptop (not) start, but obviously does not recognize the graphics card.

  After a lot of unsuccessful trials debugging on mine (including trying to upgrade the drivers to display etc.)., I reinstalled the operating system and the drivers provided with the original kit (just to eliminate any possibility of an upgrade that went wrong). However, I still see the issue.

  That means there is a hardware problem? or a BIOS problem?

  Thank you

  R.B.

  Guys, the problem you describe is actually a hardware failure. There is nothing you can do except replace a motherboard for laptop, or taken some advanced technicians, COMPUTING which will replace or chip GPU reball.

  I have the same a laptop similar (Inspiron N5110), with the same problems and these problems - all started yesterday. Do not waste your time, just reinstall OS, then install display drivers, which are available on the official site of Support of DELL and after that - if it's not working, just do what I said.

  Generally these are consequences of an overheating laptop, but that it was certainly not my case (I did regular checks), I could even bet on chips quality GPU, which has been used in the manufacture of this model of laptop... again...

  UPDATE: Okay, last night was a long night for me and I can confirm finally - who's * chip AMD, which causes the blue screen, you mentioned. I disassembled my N5110 faulty, armed with a heatgun, Probe temperature (probe) and tons of aluminium + some flow of brazing, I made a fairly quick reflow and the result is just what I expected - everything works perfectly again, with the same configuration - even with the same installation of Windows, which has been to launch these blue screens. There are now no blue screen at all and portable computer performance as new.

  Apparently bad welding, when this laptop was manufactured, is the exact reason why we are where we are. The BGA chip was not dead at all (it was just poorly soldered). The same story, including HP and a bunch of other companies had some time ago with these NVIDIA chips (I know, some of you know what I'm talking about).

  CONCLUSION: Integrated DELL diagnostic software is useless against the detection of defects with a discreet graphics AMD card. Problem was not in the software or drivers - it was just a poorly welded chip (I regularly cleaned my laptop dust, so overheating is not an option here).

• How to get the temperature, light intensity, altitude height, proximity, rotation_matrix and vector of rotation?

  Can get acceleration, azimuth, pitch, roll, and gps information.But,Could not get temperature, light intensity, altitude height, proximity, rotation_matrix, and rotation vector.
  
  Can you help me to figure out that it is supposed to work or not?Whenever tried to get these values, always show "zero".My code is at below. Does something wrong or just these valuses do not support in the Native SDK 2.0 beta 3?
  
  if (sensor_is_supported(SENSOR_TYPE_TEMPERATURE)) {        /*         * If the device does not support accelerometer then notify the user,         * clean up and exit         */        sensor_set_rate(SENSOR_TYPE_TEMPERATURE, SENSOR_RATE);        sensor_request_events(SENSOR_TYPE_TEMPERATURE);
  
      }temperature= sensor_event_get_temperature(event);fprintf(f,"%7.3f\n", temperature);fprintf(f,"%ld%d, %7.3f
  
  Thank your attention.
  

  sensor_event_get_rotation_vector
  

  
  sensor_event_get_illuminance
  

  sensor_event_get_rotation_matrix
  

  sensor_event_get_proximity
  

  sensor_event_get_altitude
  

  SENSOR_TYPE_MAGNETOMETER = 1
        SENSOR_TYPE_GYROSCOPE = 2
        SENSOR_TYPE_ALTIMETER = 4
        SENSOR_TYPE_TEMPERATURE = 5
        SENSOR_TYPE_PROXIMITY = 6
        SENSOR_TYPE_LIGHT = 7
        SENSOR_TYPE_GRAVITY = 8
        SENSOR_TYPE_LINEAR_ACCEL = 9
        SENSOR_TYPE_ROTATION_VECTOR = 10
        SENSOR_TYPE_ROTATION_MATRIX = 11
  

  There's no proximity sensor, and I suspect that the light sensor is not exposed through this API to our applications immediately, similar to what you see probably with the temperature probe. There is also no separate altitude sensor. GPS provides elevation information. Some devices (Xoom?) use something like air pressure to measure altitude but the PlayBook is not that.