WVC-200 with Hgigh Linksys Gain 7dbi antenna to 200 m router with antenna 10dbi

Similar Questions

• I can't log on to the camera wvc 200 via sololink

  HIII

  i've got WVC 200

  2 years and I am using fixed ip

  but now I'm seeing the camera via solo link

  and I activated the prot transm. for port 1024

  ,,,

  East of my linksys WAG200G router

  and I put in place the "solo" link in the camera interface (CONFIGURATION OF DDNS)

  but whenever I try, I could not CONNECT

  is there a hope?

  my solo link will expire in a few days

  Please help me

  HIIIIIIII EACH

  I'VE GOT ITTTT

  TO CAN SEE YOUR CAMERA

  GO to the PAGE of the ROUTER AND SELECT Application & Gaming

  Select a single port forwording and...

  SELECT HTTP ON PORT 80, 0R 1024 AND SELECT IP ADDRESS THE ONE INDICATED IN YOUR CAMERA

• Configuration of Gain of antenna in WLC

  Hello

  What it means to specify the PB of the antennas in the WLC for each access point. The antenna is a passive component and it is just the signal, how is that they give us the ability to specify the dBi, I don't understand the advantage and effect. If we let the zero, what is happening?

  It is important that your WLC knows what the antenna gain is so it knows what level of power to set your AP Radio to. This will ensure that power levels are within the limits of regulatory and legal in your country.

  Antennas apply passive to your signal gain after he left the AP which will result in an overall increase in EIRP (effective radiated power effective isotropic).

  Power of the AP - loss in the Cable + antenna Gain = EIRP.

  Do not set in the WLC could result in your AP exceeding the limits of statutory authority.

  See you soon,.

  Ric

• gain of antenna 0, differences between radio0 and radio1

  On a stand-alone 1131, what is the effect of not having antenna gain set at 0?

  interface Dot11Radio0
  no ip address
  no ip route-cache
  !
  encryption mode ciphers tkip
  !
  encryption vlan 1 mode ciphers aes-ccm tkip
  !
  ssid Private
  !
  ssid Public
  !
  mbssid
  speed  basic-1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0
  station-role root
  

  What is the difference between radio0 and radio1 on a 1131, just 2.4 Ghz vs 5 GHz?

  Hello

  T1 >

  Radio0

  Private SSID

  SSID Public

  Radio1

  Private SSID

  Why not put the two on each radio?

  YEARS - here the SSID PUBLIC and PRIVATE and mapped to radio 0, this means, customers that supports the G radio be able to conenct to two SSID...

  where, the PRIVATE SSID is assgned to Radio 1, which means that customers who are capable of a radio will also be able to conenct... but who are not capable of A guests to conenct to the SSID PUBLIC since its not used at all for a radio...

  Let me know if that answers your question...

  Concerning
  Surendra
  ====
  Please do not forget to note positions that answered your question and mark as answer or was useful

• Y2P has 1 x 1 or 2 x 2 gain WiFi antenna?

  
  

  sjahanmi wrote:

• WVC 200 startup disk

  I just choose two of these cameras without any boot disk, just cameras feeding I can download software or drivers for this? The version on the version 1.1 of cameras, I think I can get the power to provide local

  Download here...

  http://www.Cisco.com/en/us/products/ps9946/index.html

  For food, make sure you get the right one as the post for the cylindrical connector is not the same size as some 5 volt power supply, it is to prevent the accidental insertion of a 12-volt power.

• Need help choosing correct High Gain Antennas

  Hi all

  I was wondering if someone could please offer me assistance in the choice of the correct high gain antennas for my Wireless Linksys WAP54G access point.  I recently ordered a set of Amazon, and even if the product description says that they would, they do not have.  The product said that it was a type of connection RP - TNC, but it wouldn't fit my WAP54G.  Could you get it someone please let me know what type of connector most recent WAP54G access point?  I really need to get some antennas ordered as soon as possible.

  Here is a link to the antennas I ordered on Amazon, which has not worked for me:

  http://www.Amazon.com/9dB-Linksys-15-booster-antenna/DP/B0009U736A/ref=cm_cr-Mr-title

  Although I wish I had the real Linksys brand antennas, they are much too expensive.  If you can point me in the right direction, or maybe even send me a link directly to the product page of what I need to order, which would be highly appreciated.

  Thanks for your help, and I wish everyone a great holiday of Thanksgiving.

  See you soon,.

  ~ Marty

  The antenna for the WAP54G and WRT54G the connector are of type RP - TNC

  Do you have any RP-TNC-M or RP-TNC-F

  The connector of the antenna on the WAP54G is M, so the antenna must be F

  Concerning

  Fred

• no error message Internet with linksys wrt54g2 v1 router

  Hello

  I connected my linksys wrt54g2 v1 connect to the LAN router and the WiFi worked perfectly well. Two days there was a problem with the connection to the local network and finally he solved. Now when I connect my router wireless to the LAN, the ssid is listed and when I connect to the WI - FI connection, see an error message saying "no internet access. Could someone help me solve this problem?

  Note: I have reset the router and changed the necessary configurations, but it still does not work.

  Thank you!

  Hi varun_umesh. It is obvious that the router is no longer communicates with the modem. Try to power cycle first two devices. Once the power supply light is good on the modem and the router, check again if the internet works on your devices. If not, these links will be able to help you to reconfigure the router.

  Setting up a Linksys router with DSL Internet service

  Setting up a Linksys router with cable Internet service

• Configure 1141n with 802.11n

  Hello community,

  Currently, I'm trying to set up a 1141n (AIR-AP1141N-E-K9) autonomous access point with 802.11n. When I configure the access point for no encryption or aes - ccm encryption I am not able to set up the parameters of speed of dot11n (max. 54 Mbps). In addition, documentation (data sheet, conf IOS guide, getting started) said that the ap has two interface for (dot11radio0) 2.4 GHz and 5 GHz (dot11radio1) radio. I am not able to configure the interface dot11radio1. I tried to reset the access point to the default configuration, but this makes no difference. Even with default conf I can't configure dot11n. My question is: what am I doing wrong? Can someone help me?

  Concerning

  Bastian

  ---------------------------------------------------------------------------------------------------------------------

  Cisco IOS software, C1140 Software (C1140-K9W7-M), Version 12.4 (21a) JA1, RELEASE SOFTWARE (fc1)

  processor of Cisco AIR-AP1141N-E-K9 (PowerPC405ex) (revision B0) with K 98294/32
  768K bytes of memory.
  Card processor ID FCZ1419W0LN
  PowerPC405ex CPU at 586 Mhz, the 0x147E revision number
  Last reset of tension
  1 gigabit Ethernet interface
  1 802.11 post<---->

  ---------------------------------------------------------------------------------------------------------------------

  ---------------------------------------------------------------------------------------------------------------------
  !
  version 12.4
  no service button
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  encryption password service
  !
  hostname jug5128
  !
  enable secret 5<...>
  !
  AAA new-model
  !
  !
  AAA rad_mac radius server group
  ACCT-port of the server 10.1.111.33 auth-port 1812 1813
  !
  Group AAA authentication login default RADIUS
  AAA authentication login auth_mac group rad_mac
  Group AAA authorization exec default RADIUS
  !
  AAA - the id of the joint session
  IP zentral - .jug .de domain name
  !
  !
  dot11 syslog
  dot11 vlan-name ADMIN vlan 119
  dot11 vlan-name WLAN vlan 130
  !
  dot11 ssid junghans119
  VLAN 119
  open authentication
  authentication-key wpa version2 management
  WPA - psk ascii 7<...>
  !
  dot11 ssid junghans130
  VLAN 130
  open authentication
  authentication-key wpa version2 management
  WPA - psk ascii 7<...>
  !
  !
  Crypto pki trustpoint TP-self-signed-3181710497
  enrollment selfsigned
  name of the object cn = IOS - Self - signed - certificate - 3181710497
  revocation checking no
  rsakeypair TP-self-signed-3181710497
  !
  !
  TP-self-signed-3181710497 crypto pki certificate chain
  certificate self-signed 01
  <...>
  quit smoking
  !
  !
  Bridge IRB
  !
  !
  interface Dot11Radio0
  no ip address
  no ip route cache
  !
  encryption mode vlan 130 ciphers aes - ccm
  !
  encryption mode vlan 119 ciphers aes - ccm

  !
  SSID junghans119
  !
  SSID junghans130
  !
  gain of antenna 0
  Base-1 speed, 0 2.0 5.5 11.0 6.0 12.0 9.0 18.0 24.0 36.0 48.0 54.0 m0. M1. M2. M3. M4. M8. M9. M10. M11. M12. M13. M14. M15.
  root of station-role
  !
  interface Dot11Radio0.119
  119 native encapsulation dot1Q
  no ip route cache
  Bridge-Group 1
  Bridge-Group 1 block-unknown-source
  No source of bridge-Group 1-learning
  unicast bridge-Group 1-floods
  Bridge-Group 1 covering-disabled people
  !
  interface Dot11Radio0.130
  encapsulation dot1Q 130
  no ip route cache
  Bridge-Group 3
  the bridge-group subscriber-loop-control 3
  Bridge-Group 3 block-unknown-source
  No source of bridge-Group 3-learning
  No bridge Group 3 unicast-flooding
  Bridge-group spanning 3-people with disabilities
  !
  interface GigabitEthernet0
  no ip address
  no ip route cache
  automatic duplex
  automatic speed
  No keepalive
  !
  interface GigabitEthernet0.119
  119 native encapsulation dot1Q
  no ip route cache
  Bridge-Group 1
  No source of bridge-Group 1-learning
  Bridge-Group 1 covering-disabled people
  !
  interface GigabitEthernet0.130
  encapsulation dot1Q 130
  no ip route cache
  Bridge-Group 3
  No source of bridge-Group 3-learning
  Bridge-group spanning 3-people with disabilities
  !
  interface BVI1
  IP 10.1.119.92 255.255.255.0
  no ip route cache
  !
  default IP gateway - 10.1.119.1
  no ip address of the http server
  IP http secure server
  IP http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
  radius of the IP source-interface BVI1
  test SNMP-Server RO community
  not run cdp
  local RADIUS server
  !
  format of server RADIUS attribute 32 include-in-access-req hour
  RADIUS-server host 10.1.111.33 auth-port 1812 acct-port 1813 hits 7<...>
  RADIUS vsa server send accounting
  1 channel ip bridge
  !
  !
  !
  Line con 0
  line vty 0 4
  !
  end

  ---------------------------------------------------------------------------------------------------------------------

  ---------------------------------------------------------------------------------------------------------------------

  jug5128 (config) #interface dot11Radio?
    <0-0>Number of Dot11Radio interface

  ---------------------------------------------------------------------------------------------------------------------

  According to the output you associate with MCS rates

  "Current rate: m15.

  You will not be able to achieve the full 300Mbps throughput until you enable the channel binding, but this is not recommended from the b/g networks because it would effectivly leaves you with only one channel of Alcan.

• broadband services being hindered with MI-fi

  Top of page computer office is connected to broadband, laptop is connected via wireless linkseys.  Outside MI-fi prevents me to get online.

  Hello

  Check with support from LinkSys to change the channel of your router. Try 11 or the
  others, it's probably the 1 which is the default value. LinkSys has excellent online
  help and documentation for help in the forums.

  LinkSys support
  http://homesupport.Cisco.com/en-us/Wireless/Linksys

  LinkSys community forums
  http://homecommunity.Cisco.com/community/?category.ID=Linksys

  I hope this helps.

• wrt1900ac antennas

  Hello

  Just got my wrt1900ac and I wonder there is no technical difference between the antennas, broadcasting four antenna all the same data? or two do not broadcast the 2.5 GHZ and the other 5 GHZ, etc.. I have two high-gain external antennas and want to know which of the four, I should replace, if there is a difference or if she does'nt question that is not being replaced.

  Thank you.

  tech support says that it is not serious.

• E3000 with the same problems on &amp; more here, but no expert solution for the 2 main problems

  

  1 - with regard to support USB connected hard drives that will not transfer data & like to come & go quite often of the view.

  Everything seems like a joke to me, when I read that a lot of people have hard drives USB who worked for a year, & when it stops working or acts upward, we all have a test to see if it connects & works very well on our other connections PC/Laptop & the only advice given, this firmware is upgraded or a list of hard drives that have been tested and work on the E3000.

  2nd - my other problem is that my E3000 now decides of its own to disconnect wireless & cable Communication and then reconnect alone, whenever you feel.

  What makes angry of this problem is that it is abundant in the Forums & I tried all the fixes, but I still have the same problem & sound as good as this device of 2 year, Max is grilled.  As is the case when there is a loose connection that overheated, in what thread or welded metal move when heat is added & move at the time where the heat is removed.

  PROBLEM:

  My touch 1 Maxtor (from the approved list) is connected and playing now you see me & now you don't game.  If I ever try to import or to export any image file or music, the Communication goes & then sometimes will return its own. Working with Game Consoles, when something begins to work intermittently, then it is a hardware problem or software with the device.  It is not a user error, when it worked fine before.

  SOLUTION?:  This is why we are all here. Thanks to a landmark of expert for the same problem that many of us have?

  How about this solution. Why not let all E3000 owners send there wireless routers is not working towards a credit for a new operating model nice. I think that we would all save a lot of headaches & get rid of 25% of all calls for help on this forum.

  Thank you for your attention,

  BigdogTim7

  PS. Please give us/me expert advice on how to solve the problem.  If nobody knows the answer, then Cisco/Linksys looks really bad for selling a router high of $$$, being touted for the games and files sharing multimedia home & it only at this stage.  If it should be recalled, will bring up by all means, or come up with a fully functional firmware.

  Thanks again & hope to hear news good & productive, cause I am so tired of playing with this E3000 & will more than likely stay away from your product for any & all future purchases, no matter where you are ranked (E3000 was 3rd & best prices of the top 3 when I bought it).

  Well, I'm here, not having heard an assumption about my problem, but to get an opinion of experts & solution to my problem, but also all other users of the same or very similar problems.

  I am now a HAPPY 'Belkin N600 DB' owner for only $79.99 @ Wal-Mart/Radio Shack. This new does much more than the Cisco E3000 wireless router & even changed my Modem 100 MB (green) flow out of 1000 GB (Amber Light).

  So, so HAPPY now!

  Bigdogtim7

• Seamless roaming with EA7500 + RE7000 the two AP work?

  I have a wired router provided by my ISP at home and a few wireless (wired connection to the router, DHCP off) covering the rooms. The experience of homelessness is terrible, and I am considering buying an EA7500 and a RE7000 to replace my existing APs.

  But after this post EA7500 is not compatible 802.11r. It is a surprise for me. I would like to know which of the following configurations provides the best mobile experience, or are they the same?

  (a) 1 EA7500 + 1 RE7000, both working as AP, wired to the router;

  (b) 2 RE7000 works like AP, wired to the router.

  With option one) I also use EA7500 for storage network etc., but homelessness experience matters more for me.

  @Carolina

  If the two Linksys RE7000 are both connected to the router, they will act as an Access Point, however, adding another extensions (RE7000) wireless to remote locations is possible depending on the coverage of your network. BTW, check out this link how to configure 2 Linksys RE7000 for seamless roaming. You can also check out this other link to set up your RE7000 with a Linksys Max-Stream router.

  Jay-15354

  Linksys technical support

• Fine continuous with G Router but not with N

  I recently bought a N-Router Linksys E2000 to replace my current G-Router Linksys WRT54GL in hopes of having the best connection for my Boxee Box wireless. I discovered that my Boxee Box have some problem (every 10 to 20 seconds) of buffering when streaming files .mkv 720 p or 1080 p Wireless with my E2000. I decided to put my good old... surprise and WRT54GL! No buffering... even with my mkv 1080 p... files! I also give it a try to transfer a TV show in 720 p (mkv) by wireless in the HARD drive connected on the Boxee... I have an average speed of 1.70 MB/s with the WRT54GL and not still 400 KB/s with the E2000... What's the problem with him?

  The latest authentic firmware both have 2 routers. The E2000 is set to mixed mode, auto channel and WPA2-Personal (AES). The WRT54GL is set to G only, Channel 6 and WPA2-Personal (AES). Is there something I need to check on my E2000 wireless settings?

  Thank you!

  Change the channel on E2000 to 6 or 11. Save the settings.

  Also try to change some advanced on the router settings wireless. Click on the Wireless tab and go wireless advanced settings. Change the tag to 75 interval, RTS threshold to 2307 and 2306 fragmentation threshold. Save the settings.

  Go to the Configuration tab and change the size MTU to 1365. Save the settings and the cycle of power to the router. See if that helps you.

• Using a cellular provider like internet access with an E4200

  Hello:

  I want to upgrade my home network a WRT300N towards a new E4200 and spend my MiFi cellular access DSL internet provider.  (The spd DSL is only 500K, and I can get up to 21 MB on cell phone at about the same cost.  Woopee!

  The problem is that only my supplier available a cellular access system is also a router without wire - a home network router small no less - a 4 G Netgear MBR1210 Turbo hub.  But she has a few ports ethernet on it.  So I think that I must configure network settings domestic suppliers to be totally different from my outgoing home network (different SSID, channel and different home range of IP address, disable DHCP if possible, via its outputs ethernet plug at the entrance to the INTERNET on the E4200 with a short ethernet cable and then use my Linksys as the DHCP server and the router for my home network wireless network.)  I have a very large network with many devices much more on what block takes care of the provider.  I can configure the linksys E2400 to accept the IP address that the MiFi unit never gives him as my Internet service provider entry and then configure the rest of the network, as it used to be with my older Linksys WRT300N router?

  See you soon!

  I think it should work.

  Connect your service provide router on the Internet on the E4200 Linksys port.

  Open the E4200 configuration page and check the IP address on the State of your router?

  Try to follow this link to routers towing cascading.