XPS M1210/Vista - cannot listen to device connected to the line in jack through the speakers.

Similar Questions

• NWZ-B172F cannot open, when it connected to the PC, it shows Mr. USB VERBINDEN. How to solve it?

  NWZ-B172F cannot open, when it connected to the PC, it shows Mr. USB VERBINDEN. How to solve it?

  Hi sean2sun,

  It seems that the player is not correctly recognized.

  What is the operating system installed on your computer?

  However, try to disconnect and reconnect the Walkman on computer. You can also try plugging it into different USB port of computer.

  NOTE: Connection to the USB hub is not supported. Walkman should be connected directly to the USB port on the computer.

  If the problem persists, perform the steps on the below technical support article:

  https://La.en.KB.Sony.com/app/answers/detail/A_ID/42398/p/57784, 59687,59899, 71847/c/65,75/kw/Walkman...

  If my post answered your question, please mark it as "acceptable Solution".

• Is there a way to see the ip address of the devices connected via the airport?

  Hello world

  Is there a way to see the ip addresses of the devices connected via the airport? I can see the name of the devices but not what ip are they?

  Thanks in advance.

  Open AirPort Utility

  Hold down the option on your Mac so you double-click on the image of the AirPort router

  Wireless clients are displayed

  Click on the small arrow next to each wireless client to see details about the device and the connection

• Does anyone has a software that can give the ip address for any device connected to the laptop, as the Council of access control?

  Hello team,

  Does anyone has a software that can give the ip address for any device connected to the laptop, as the Council of access control?

  Thanks for help

  LookAtLAN network monitoring is one of these tools.

  SuperScan is probably better, but I have not tried.

• Names of the devices connected to the router

  How can I tell the names of the devices that are connected to my router E2000? Cisco connect says I have 4 devices but I only have 3. I'm trying to understand source of the 4 device.

  Open the Cisco connect software. Go to "Setting up the router" and click "Advanced settings". Who will open the router configuration page.

  Click the status tab. Go to the tab "Local network" sub on the button "DHCP Client table". Here is a list of the devices connected to the network.

• EA6500 only shows no device connected to the switch of working group 5 ports

  I just replaced a defective Linksys e4200 with an ea6500.  After assistance by phone, I got to the top and work, but only one computer on my LAN is not displayed.

  I connected an 8 port 10/100 switch Linksys my 4200, and my wife's computer was connected to that.   The computer displays the IP as 192.168.1.133 and it is connected to the internet with my router again.  But the ea6500 does not show a device with the ip address.  Instead, he shows what he calls a network with the IP 192.168.1.130 device.

  How can I see the devices connected to the switch 5 ports and determine which ip addresses, they have been assigned?

  I use a switch with my network with a router EA and it shows the devices correctly. Turn off the computer which does not appear in the list of devices and check to see if any device will appear as offline adter who. Remove from the list of devices, and then restart the router. Once the router is ready, open the page of the router again and turn on the computer and check if it will be detected correctly. I hope this helps.

  Edit: Check and make sure you have the latest firmware loaded. Otherwise, update the firmware and do a reset after the update of the firmware. Check your list of devices after that.

• Get the IP addresses of the devices connected to the WiFi network

  Hello guys,.

  I've been looking around and trying to understand this point, but I don't have a solution. The problem is to get the local IP addresses of all devices connected to the WiFi point of access/router connected to my BlackBerry. Similar to the way in J2SE nature you can get the IP using InetAddress.getLocalAddress () and then browse ip addresses and call InetAddress.getByAddress (ip) to check whether the device is accessible. Possible is something similar in BlackBerry or not?

  No, the fault was entirely mine, I misread your message.
  no idea how to do that, there is no access from low level of the network interface and the API is really limited.

• The list of audio devices connected to the operating system has been changed

  Hello, I have a problem with rendering in Media Encoder CC. When I realized the video suddenly a message "THE LIST OF audio devices connected to the operating system was changed. Open Audio hardware preferences? "and rendering are collapsed by increasing the time until infinity.

  Any suggestion?

  Thank you very much.

  

  

  [Moved the Forum of the SOUL of the After Effects - MOD forum]

  Hmmm.  It's very strange.  For the experience, I tried to disconnect a sound card, while the SOUL is coding.  I get the message dialog box, but the encoding continues without stopping.  Eventually, this may be specific to certain sound cards.  What is your sound card that you have on your computer?

  For a workaround, could you try checking the "do not show again" checkbox in the message dialog box next time you see it?  Then, click no you should not see this message again and I hope that this problem would disappear.

• VISTA: cannot use my Ethernet connection

  I use Thinkpad X 200 under Vista 32 bit, my ethernet card is Intel 82567LM.

  I connect OK for wireless network, have never tried to connect to an ethernet connection before with this laptop. But when I did, it doesn't.

  What tests I've done:

  (1) manage the connection: connection to the LAN - State is 'ENABLED' (sorry I translate this from a Chinese OS, don't know if it's the right terminology, CONNECTED or DISCONNECTED)
  -Right-click and enter in the properties-> IPv4 is checked, and in properties, all is get automatically
  -Diagnose this connection-> he says "does not correctly configured to use the IP Protocol, please make sure that IP is correct" (translated)

  (2) I go into Device Manager and find the ethernet card and update the driver to the latest version. Uninstall the driver and let Windows reinstall it at startup-> still no luck.

  (3) IPCONFIG-> shows only TWO (should not be a?) Wireless WiFi and a Tunnel to the map (?) and ETHERNET adapter WITHOUT connecting to the LAN (VERY STRANGE).

  (4) when the ethernet cable is plugged in, the lights are on, so the port and the line must be good.

  Could someone please help? Thank you! I'm really at the end of my intelligence...

  Hi Cody,

  Thanks for your suggestion. Appreciated! It is portable to my friend, and after tried so methods and still not, she gave to solve to get a router to convert the wired connection to a wireless. Now she's happy with the connection that it becomes.

  I guess I won't have a chance to try your suggestion a while later... Thanks anyway!

  Have a blessed Sunday.

  Clark :)

• HDMI going offshore and on the Windows Vista system when it is connected to the TV.

  Original title device: Windows vista HDMI

  Eh_bien, I have connected to the computer with a HDMI, (TV with HDMI output) device) the system is windows vista, but always goes off and turn it back on, it turns off the HDMI device and allows the device installed on the pc. As always, I can do to stay enabled HDMI device?, the HDMI device is always connected.

  I appreciate your help.

  Hello

  Method 1:

  Perform a clean boot.

  Put your boot system helps determine if third-party applications or startup items are causing the problem. If so, you need to maybe contact the manufacturer of the program for updates or uninstall and reinstall the program.

  See the following article in the Microsoft KB for more information on how to solve a problem by performing a clean boot in Windows Vista or Windows 7:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note:

  After troubleshooting, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

  Method 2:

  If this does not work then you can try updating the graphics card driver by visiting the manufacturer's website

  See also:

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  Method 3:

  Please check the same in another port and also try it on a different TV with working port known.

  For more information, you can also see:

  HDTV: Frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/HDTV-frequently-asked-questions

   

  TV on your computer: understanding signals TV and TV tuners

  http://Windows.Microsoft.com/en-us/Windows-Vista/TV-on-your-computer-understanding-TV-signals-and-TV-tuners

  Please answer back so that I can help you

   

• "Cannot find server" when connecting to the database homepage

  Until someone tells me to look at the other post on the first page of the forum with a similar title... I've already read through it. I also did a search of the forum, but I'm still stuck.
  
  Let me start by saying that I have almost no experience on one database other than writing queries. I installed Oracle Express 10 g today for I can have access to a development environment to test my queries on the sample data. After installation, it automatically opens a web browser, pointing to the URL: http://127.0.0.1:8080 / apex, the page could not be loaded (error Internet Explorer: "cannot display the page." and at the bottom of the page: "Cannot find server or DNS error"). I decided to restart my computer to see if that would make a difference. Then, I opened the link 'Start' in my Start menu in the new folder of Oracle. It instructed me to first of all, go to the home page of the database (with the same URL: http://127.0.0.1:8080 / apex), and the page still doesn't load. Based on the posts that I could find on the subject, I chose "Start Database" of the Oracle folder in my Start menu. In the command window that pops up, he says:
  

  C:\oraclexe\app\oracle\product\10.2.0\server\BIN>net start OracleXETNSListener
  The requested service has already been started.  
  
  More help is available by typing NET HELPMSG 2182.
  
  C:\oraclexe\app\oracle\product\10.2.0\server\BIN>net start OracleServiceXE
  The requested service has already been started.
  
  More help is available by typing NET HELPMSG 2182.

  Then... It looks like the database and listener are already started, so I don't think that's the problem. So, I'm stuck. I am trying to access to this on the same computer, I installed it, and I don't plan any time in the future where I will need to access the database remotely because it is just a test environment for my personal use.
  
  The most recent post on this subject, I saw something to try to go to http://hostname:8080 / apex. And, forgive me if this sounds like a stupid question, but I guess I have to replace "hostname" in this URL with whatever hostname actually is... right? So, uh, how can I know what is the host name?
  
  Published by: user11033437 on April 15, 2010 13:18 (corrected to default URL)

  Well, looks like the answer to one of the previous questions, "isn't the database running" was ", not really" :(

  If there is no newspaper alerts, there no database, most probably the \oraclexe\oradata\XE\ does not contain. DBF files - try manual cleaning (remove registry entries, the Windows install cleanup, etxc.) following ALL the steps in the http://download.oracle.com/docs/cd/B25329_01/doc/install.102/b25143/toc.htm#BABFFJIB

  And check to make sure that your connection to the PC is in the local administrators group (domain administrator is not enough here) and run the installer... what version of Windows? XP? 2003?

• iPod touch cannot turn off and connect to the server

  He always responds to my touch, but it does not turn off when I press the lock button or the lock screen in a long time.

  At first, I tried to open an application, but he was stuck with the logo page, so I thought it re - install but then when I opened the app store it is impossible to connect with the Wi - Fi connection. Then he started does not, stuck with notif center I have accidentally fired. When he locked the door, that I unlocked it and it was back to normal. So I tried to disconnect and reconnect to the definition of id apple, but it says verification failed and I couldn't sign.

  I also tried checking on the software update, but it says unable to connect, and I do not remember whether or not I have updated to the new iOS.

  Help, please!

  Try:

  -Reset the device iOS. Nothing will be lost

  Device iOS Reset: Hold down the On / Off button and the Home button at the same time for to

  ten seconds, until the Apple logo appears.

  -Reset all settings

  Go to settings > general > Reset and tap reset all settings.

  All your preferences and settings are reset. Information (such as your contacts and calendars) and media (such as songs and videos) are not affected.

  -Restore from backup. See:

  Restore your device from an iCloud or iTunes backup - Apple Support

  https://support.Apple.com/en-us/HT204184

  -Restore factory settings/new iOS device.

  If still problem, make an appointment at an Apple store Genius Bar because it appears that you have a hardware problem.

  Shop Apple Store - Genius Bar

  https://www.Apple.com/retail/Geniusbar/

• Qosmio G50-12 q - how to configure the devices connected to the USB mode standby

  Hello

  I wanted to use the PC sleep function.
  I also wanted to as devices that have been extinguished when in stand by.

  Once implemented this function the PC will regularly stand-by, but the device connected by usb are set on fire, any other master type, a device a usb wi.fi, etc.

  Someone told me that maybe some functions in the Bios only are not put in place to do that once entered the booth by the PC off all devices those connected.

  What checks and I have to perform in the configuration PC bios?

  How we in the bios? By pressing the keys on which?

  Thank you

  * valkyrie @ *.

  Please post comments if workaround posted by Akuma helped!

  It would be really appreciated.

• Update IOS 9.3 cannot download msg "not connected to the internet.

  Tried to download 9.3 IOS for iPad 2 IOS v.9.2.1 & msg cannot verify the update (.. .no more connected to the internet) same msg as others did.

  How to get able to send this msg + do all other internet functions.

  Tried to leave for several hours, turn off / turn on modem, go into iTunes on iPad & iMac.

  Community checked and a number of reports the same problem for several days, strangely, was also problem in 2014!

  So the time for Apple to fix it as soon as POSSIBLE.

  I also have the same problem, but in addition I have problems with the Google search function. The results come but there is a lock in the search bar, and it is not possible to open all results

• HP Slate 17 l010: HP Slate 17 l010 cannot establish a reliable connection with the server

  Hi, the other day, I lit one of our tablets HP Slate 17 L010 and started getting the message above. I factory reset the device and still get the error. I can connect to the internet on the device but can't seem to add all Google accounts. Someone at - it advice to solve this problem?

  Hi!, @joshhm:

  Welcome to Forum!

  See the Guide to the user, page 10 and later... Chapter 3... http://h10032.www1.HP.com/CTG/manual/c04446211

  Try with update.zip, of... http://support.HP.com/us-en/drivers/selfservice/HP-slate-17-L000-all-in-one-desktop-PC-series/7161751/model/7276370

  Note: previously, select the software in your country.