Yellow ink not print not

Similar Questions

• HP Envy 5530: Yellow ink not print

  Yellow Ink stopped printing with the Tricolor cartridge; replaced by the new HP cartridge and not yet. Also tricolour ink not detected.

  Tried all the steps HP support, including the persistent page terminals on the cartridge and to the holder. Also reinstalled driver. No change.

  Is this a hardware problem? The printer is only 6 months old and so under warranty, but I buy an Epson if it is!

  All ideas welcome

  Thank you

  6 months and under warranty. Call HP for replacement.

• MG5320 yellow does not print

  Hello

  My printer has stopped printing the yellow cartridge always. The cartridge is almost full. I did a cleanup and a thorough cleaning and aligned automatic print head a couple of times. The nozzle check page does show no yellow but everything else is fine.

  Ideas?

  Michael

  Hi graywolf28,

  As cleanings and alignments did not get yellow ink to print, remove and reinstall the ink tanks and print to the printer head, ensuring that all bands who may be staying on the ink tanks has been removed and put them all in the printer.  If the ink still does not print, the printer will require maintenance.  Please call or write to us at one of the methods on the contact us page to get your service options.

• Photosmart B210 trouble with yellow ink

  I'm not able to get yellow ink to print.  I ran the numbers of function clean print head of time without success.  In addition, the printer status report indicates no yellow in the estimated ink level column and the installation date of the ink does not - I just put two new cartridges yellow today!

  Help!

  Hey JoeMyer,

  Welcome to the HP Forums!

  To clean the printhead several times and replacement of the ink cartridge. This proves that the problem is with the print head. I've included the link to the HP Forum thread "black ink does not. This has been posted for a black not printing problem, but operations continue to operate since you don't print Yellow.

  Please let me know the results of the resolution of the problems.

  Thank you.

• HP OfficeJet Pro 8000 Wireless: Can I get some help here? Yellow ink will not print - HP OfficeJet Pro 8000 Wireless

  No matter what I do, ink yellow does not print, or stops at halfway printing on the page. I use genuine HP cartridges. There is a lot of ink - in fact, I just installed a new cartridge in the case where a previous (almost complete) was defective. No change. The pipe is not pinched. I flashed the firmware more recent and installed all drivers and utilities updated. I have cleaned the print heads over and over again and even took and cleaned according to the instructions.

  I think it was a sign that the printer is worn EXCEPT - just a few months ago, magenta and black stopped printing. These are the opposite printheads. When I uninstalled every bit of HP software I could find, the printer back to normal!

  The only thing I did not - it is the HP Toolbox argues that it is impossible to establish two-way communication with the printer. The patches for this involve get under the desk to play with the power cord and USB cable (even if it is a wireless printer), and my arthritic knees that make a very delicate operation. Two-way communication IS enabled.

  I'm about to start crying. I fought with this market a week, when the yellow all of a sudden went - once again, * most * of the time, but sometimes it prints to maybe an inch of the image before disappearing. Help!

  Hi @Echo2,

  Thanks for joining the Forums of HP Support for a solution to your printing problem.

  I understand that you use a HP Officejet Pro 8000 printer with a Windows 7 computer and all of a sudden is not printing yellow ink. I would like to help with that.

  Here is a document of support for the print quality problems - Troubleshooting print quality problems.

  Please let me know if that solves the problem, or if you need assistance.

• HP all-in-one 8620: HP all in a single 8620 - will not print black because yellow ink so you are done?

  What nonsense, the here!

  my printer refuses to print black and white, pages saying that the yellow ink is finished?

  only if I buy a wet ink yellow it will print.

  Isn't this black mail? What does take to print?

  I did print it in black, etc, but still it prints no and gives a banner saying yellow ink purchase

  The standard yellow ink is available from HP here.  You can also consider the Multipack colourful three - if yellow is probably exhausted the other colors are not far behind.

  With regard to the requirement to have the ink color when you want to only print in black.

  HP and other printer manufacturers have technology another printer for different needs.  For ink jet printers:

  • Some have integrated into the ink cartridges print heads.  These printers can print generally with one or more of the colors completely empty, or even with color or black cartridges (but not both) removed. Deskjet 6980 series is an example, or for an all-in-one, see the 8040 a Officejet.
  • Other printers have separate replaceable printheads and inks.  An example would be the printer Officejet Pro 8620.  In these printers print head can be replaced if they are damaged by running the printhead with colors off.  Some of these printers allow printing with a color, the other will not.  If the printer is run without ink in one or several colours, the printer may be damaged, but the user may be able to recover without having to send the printer for the service by replacing the (expensive) print head.
  • Other printers have permanent print heads.  To run only those without little ink in all colours would risk causing damage to the print head because of clogs, air ingested in the printhead or grilled printhead resistances of shooting. The Officejet 6700 is an example of this type of printer. For printers with fixed print heads that could require the service to get the printer to print properly again when the ink is finally replaced.

  The document described here how the ink is used.  The document is written for inkjet printers HP the same principles apply to printers inkjet from other manufacturers.

  If you are ever printing a monochrome laser printer in color would probably be a better choice.  If you occasionally print color but especially black a HPI printer as those in the first category above can be a good choice.

• new yellow ink cartridge (564) do not correctly print Photosmart HP 7510 e-all-in-one

  My Hp Photosmart 7510 e - all - in - one... I replaced the yellow cartridge XL 564 and I am getting yellow streaks... when printing a report, yellow is barely noticeable, with black stripes.

  Is this a faulty new cartridge?  Help, please!

  Carol

  DUH!   A senior moment here... I pulled out the yellow ink cartridge replaced by another new... at that moment, I realized the orange tab 'pull' was still attached.   Once I got his shot and re - insert the cartridge, it was fixed!

• can not have only black when printing black but not yellow ink

  HP photosmart D7260 uses.  having run out of yellow ink.  only need to print in black now.  By selecting only black AM but the screen says I can't print at all, unless I have reconstitute the yellow ink.

  any solution short of buy yellow ink?

  The short answer for this printer: Yes.  For the Details of how the ink is used, see here.

• HP Photosmart C6180 Magenta Ink not printing

  error message: no

  description of the problem: Magenta Ink not print not EXCEPT on the page that prints after aligning the print cartridge printing is performed. At the bottom of this page, the bars of yellow, Cyan and Magenta print perfectly, just like the mixture of the color shown in the colorful bird printed below the bars.

  Self Test Diagnostic Page is printed with bars No. Light Magenta or Magenta, under print quality model. State of ink and level for both shows like OK magenta and 100%

  Troubleshooting: I ran repeated cycles of head cleaning and aligning the print cartridge print without changing the output. The page that prints after cleaning has NO magenta bars or lines. Seems the page that prints after alignment. Via e-mail support, I was directed to perform a complete reset "semi" and "the NVM reset" - neither of these had no effect. Magenta inks have been replaced, but the problem persists.

  Exchange: the printer had not been used for several months.

  My printer started working. It had been disconnected and sitting for several months. I turned it to try the HP solutions (below) and found that it worked - I had nothing to do!  In any case, I hope this can help some of you with similar problems:

  Hello
  
  Thank you for contacting HP Total Care.
  
  I'm Vivian of HP Total care for all-in-One products, and this response is in what regards the problem with HP Photosmart C6180 all-in-One Printer.
  
  Of your mail, I understand you have a HP Photosmart C6180 all-in-One Printer. Currently, you have a problem in which the printer prints in magenta only on the alignment page and not even on the test page.
  
  I am aware of the importance of the issue and will give you the appropriate information. I need your cooperation and appreciate your efforts to resolve the issue.
  
  First of all I want to thank you for the link, I'll take that as a feedback and will forward it to the concerned Department. However it is not a known, issue because in this case, HP will take immediate action and make sure that defective cartridges do not reach the market.
  
  Please try the following troubleshooting steps. I assure you that those measures would solve the problem.
  
  I ask you to check if you have the same problem with the copy as function. If the printer copy very well magenta do not perform one of the steps given and please get back to us for further assistance. However if you encounter the same problem with the copy as well please continue with the provided steps.
  
  First step: clean the copper contacts.
  
  (1) take a lint cloth or a cotton ball, it wet with water.
  (2) clean the cartridge copper contacts.
  (3) you have the same type of copper on the printer also, contacts if you are able to reach their own contacts in copper on the printer also.
  (4) reinstall the cartridge in its housing.
  (5) when the printer is on, unplug the power cord from the printer.
  (6) press and hold the power button for about 30 seconds.
  (7) re plug the power cord into the printer and the printer.
  
  If the problem persists, proceed to the next step.
  
  Step 2: Perform a drain of power on the printer.
  
  (1) remove the power cord from the product
  (2) press and hold the power button for about a minute (while the power cord is not connected to the printer).
  (3) release the button.
  (4) connect the power cord to the product
  (5) use the button to turn the product on.
  
  Connect the printer to the computer and check; If the problem persists, proceed to the next step.
  
  Step 3: Reset the printer to the factory settings.
  
  (1) use the button to turn the product on.
  (2) remove the power cord from the product
  (3) press and hold the # and 6 buttons.
  (4) while now buttons, plug the power cord to the product
  (5) to continue to press the buttons for about 30 seconds.
  (6) use the button to turn the product on.
  (7) if these steps do not resolve the problem, it will be a hardware problem with the printer in this case I suggest you take the printer to the nearest authorized Service Provider for the service.
  
  Please follow these steps and get back to us with the results, if you need more help, please reply to this message and we will be happy to help you further.
  
  We look forward to hear from you.
  
  For more information on keep your HP and Compaq products up and running, please visit our Web site at:
  
  http://www.HP.com/go/TotalCare

  ALSO:

  If the printer performs the color copy and you get magenta on the copy, it is obvious that the printer works fine, it's a software problem. I ask you to try the following steps, depending on your convenience and get back to us with the results.
  
  First step: reset the printing system
  
  To use the reset printing system feature, follow these steps:
  
  1. in the Finder, choose utilities from the menu reach.
  2. open the printer setup utility.
  3. in the printer setup utility menu, choose Reset Printing System.
  4. click on reset.
  
  Second step: check/repair disk permissions
  
  Click on Go tab in the top menu bar.
  Select the utilities tab.
  Click disk utility.
  Once disk utility appears, select the drive and click the check permissions.
  
  This can take a long time to complete as the Mac will try to check all permissions to the hard drive.
  Now click on the tab authorization to repair disc.
  
  This can take a long time to complete as the Mac will try to repair all permissions to the hard drive.
  Once Permission to disk check is complete, restart the Mac
  
  Step 3: Add the printer again
  
  1. click the Apple on the top of the left hand button.
  2. click on Preferences system, window system preferences will open.
  3. click on the printers and faxes icon.
  4. click on add the symbol on the bottom of the left hand.
  5. you see your printer in the list, select it and click Add on the right side.
  
  Please, do the following and get home with the results, for further assistance please get back to us, we will be happy to help you.
  For more information on keep your HP and Compaq products up and running, please visit our Web site
  to:
  http://www.HP.com/go/TotalCare

• Photosmart 7520: hp photosmart 7520 yellow ink cartridge will not in (pop out of space)

  I tried to install two different new HP 564 XL yellow ink cartridge in my Photosmart 7520. They arise constantly from their slots. I managed with the magenta cartridge that is similar, but the yolks do not remain in place. What is the solution?

  Hi Rebmark, I did some research and found a troubleshooting page that describes some steps that might solve this problem.
  
  http://support.HP.com/us-en/product/HP-Photosmart-7520-e-all-in-one-printer-series/5199461/document/c02944025

  Step #9 may be the answer you're looking for. When the ink cartridges is not properly connected, it can help try gently bending the cartridge tab try to avoid to bend this tab over a half inch, as it could damage the cartridge.
  
  I hope this helps, but let me know if you're still having problems!

• OfficeJet 6500 has more: printer will not use BLACK ink to print in BLACK. Mix of colors rather than use BLACK.

  Printer prints BLACK ink BLACK, instead he mixes the colours to make BLACK.  It creates copies in BLACK only, without mixing colors to achieve the BLACK, but when I ask it to print something it automatically uses the ink color.

  In properties, advanced, I checked the box to print in BLACK only, but did not help.

  In the printing preferences, shortcuts, where it says printing in grayscale, do you feel black ink only as a default?

  I don't know if it will work, I do not use this parameter or the Advanced setting, I have been using high-quality grayscale, but I'm interested to know why, also, when I print 99.9% of the time with color, what I need to change the color ink cartridges so frequently.  You say the color of those who are used to make black.  That makes no sense to me either why the printer would do that, except high-quality grayscale means he uses color inks vs only Black Ink is not.

  Test printed with two parameters, and that is exactly the same, so I won't set my default preferences for levels of gray-black ink only printing and see what happens.

  What how can you tell whether or not the printer is mix colors?  (by the way, if you use unusually fast color ink)

• OfficeJet Pro 8500 depleted a color ink cartridges - printer will print not except if replaced

  When one of my color ink cartridges is empty ink, my printer does not print until the ink cartridge is replaced.  Of course, I go out and buy new and install it then get the message that another cartridge needs to be replaced!

  I only print in black ink in all cases.  Is it possible to print only black ink without replacing color cartridges are empty ink?

  In addition, if a color is exhausted, I should automaticall replace all color cartridges?

  Operating system: Windows XP

  Officejet 8500 printers individual ink cartridges (IIC); This machine requires that all cartridges to be installed to ensure that the printhead not damaged. In the printer, the ink is used not only for printing, but retain the printer and the print head. We can reduce the amount of color ink, the printer uses by changing the print in grayscale settings or use black ink only. Page 34 of the Manual shows how to change these settings when you print the documents. For more information on how the ink is used in the printer; It can be considered as this page here where he goes into detail about the different ways that ink is used in the printer.
  I would just replace the color cartridge the printer says needs replacement when the machine alerts you of low ink. I would replace all the colors at a time when only needs replacement.
  I hope this helps.

• Solved my printing black ink not not problem

  I had the problem with the black being very low and broken text in the lines. I found if you use the screen of the printer on the printer itself and select the Setup Menu, then choose Tools, then the arrow down once on the down arrow and you should see an option clean printhead. I ran it about 3 times and my black ink is printing dark as it should. I would say that for those who do not receive any black ink may have to repeat this as many times more than me. Also, make sure that your black ink level is sufficient to repeat the process so that you don't miss. Good luck!

  I have a model B209A, this may not apply to all the print heads cleaning Interior, only most of the printers that have a touch screen on their printer.

  This post couldn't have come at a better time! I had just installed the new cartridge tonight and my black one was not working! Thanks for posting your results and I hope this helps a lot of people! I was stumped until I found this!

• HP Office Jet Pro 8600: HP Office Jet Pro 8600 on MAC not recognize refills of ink and printing habit

  When I print wireless, the printer gives me message that the ink is low and he used to feel. However, the printer has new cartirdges of ink and printer records only.  I can print with a connector of my HP laptop to the same printer and it works fine.

  I restarted my MAC and I don't know what else to do. Very frustrated that I use this printer with my MAC every day and a lot. Help

  Problem solved.  Printer works wirelessly.  I thank very you much for your patience with me and for your excellent step by step insttuctions.  I really appreciate you and the work you have done.

• Unable to print black and white with no yellow ink L7590

  I ran more ink at the weekend and got a new black ink cartridge. Unfortunately, I did not notice that I was also out of yellow ink. I desperately need to print regular black text, but the printer refuses because he is more yellow ink! I don't want print Yellow. Is it possible to disable this error message for a HP OfficeJet Pro L7590?

  Thank you.

  Nevermind, I figured it. If you set the printer on the mode of manufacture, it ignores the ink levels. Sorted.