10.11.5 broken SMB YET :-(

Similar Questions

• Breaking SMB permissions after the NAS host name change.

  Broken SMB permissions after the NAS host name change

  ReadyNAS 104 firmware 6.5.1

  Who can help me?

  I couldn't reach the NAS with Windows Explorer. Problem solved now.

• IdeaPad Y400 keyboard broken after installation of Ubuntu. Sent in, Lenovo has sent back still broken.

  I have a Y400 Ideapad, purchased in December 2012, delivered with Windows 8. He has recently due to a malfunction after trying to install Ubuntu as a secondary OS. It was very difficult to get installed Ubuntu because UEFI and Secure Boot really tried to stop him, but I have finally installed it and the two operating systems, has been working for about 24 hours. Then, Ubuntu was able to start. On several occasions. Then I started Windows and it seemed that he was working again, except that from time to time when I tried typing, the keyboard type keys I had not touched and then stop responding for about 30 seconds. After that, it would still work for a little while.

  I ran OneKey Recovery to try to solve this problem, wiping my hard drive and reinstall Windows 8 from scratch. Still doesn't solve it. He actually glitched once while I was still setting to the top of my Windows profile, before he had even started for the first time.

  So I sent my laptop for Lenovo and, a week later, they sent back with a new keyboard (despite me telling them that it probably wasn't the problem). He worked for the next few days, but as of today, he started glitching again, much. I don't want to send my laptop for Lenovo again because I need for the class I'm taking. Also, when they sent it the first time, they have not even put it together right. The rear panel was not at bottom, and panel below which was actually folded so that one of its tabs fit on the side of my laptop instead of being inside.

  I really need to solve this problem, but I'm doubting the capacity of Lenovo to do, and I don't want keep it will send if it simply means that I won't have a laptop for 1-2 weeks and then I'll get it broken back yet more. Also, I need even Ubuntu, even if they do not fix it then I have to reinstall Ubuntu and it will probably break again. Not to mention, they will probably wipe my data from it.

  Found a thread discussing this:

  http://forums.Lenovo.com/T5/IdeaPad-Y-U-V-Z-and-P-series/IdeaPad-Y400-keyboard-auto-typing-and-out-o...

  Turns, the Y400s have a defect. If you select always "on USB" in the BIOS / menu UEFI, it messes up your keyboard. I have activated it when I was trying to get my computer to recognize a USB boot.

  I'm surprised a Lenovo support is not already aware of it. I talked to Lenovo about a dozen employees, including a supervisor and a representative of the customer relationship and no one suggested she could relate to my BIOS settings.

• Someone at - he used CameraRoll yet? Seems completely broken.

  I am currently implementing navigation for a file using the CameraRoll since File.Browse () methods are still badly broken. I have implemented a method of load using the example of the documentation. Unfortunately, it seems simply crash the application. Here's the code to date.

  private function load(e:MouseEvent):void
  {
      trace("loading");
      menu.close();
      if( CameraRoll.supportsBrowseForImage )
      {
          var mediaSource:CameraRoll = new CameraRoll();
  
          mediaSource.addEventListener( MediaEvent.SELECT, imageSelected );
  
          mediaSource.browseForImage();
      }
      else
      {
          var myFile:File = File.documentsDirectory;
          var filter:FileFilter = new FileFilter("Images", "*.png;*.jpg")
          myFile.browse( [filter]);
          myFile.addEventListener(Event.SELECT,chooseFile);
      }
  }
  
  private function imageSelected( e:MediaEvent ):void
  {
      trace(e.target.nativePath);
      img.setImage(e.target.url);
  }
  
  private function chooseFile(e:Event):void
  {
      trace(e.target.nativePath);
      trace(e.target.name);
      var name2:File = File.desktopDirectory.resolvePath(e.target.name);
      trace(name2.nativePath);
  
      img.setImage(name2.url);
  }
  

  I'm detection to see if the film is supported and then using one of the two callback methods to load the file.  It could be done with the method of a reminder if we could rely on the event. Target property from the File.Browse method, but we cannot and this is another problem.

  In any case, it seems very simple. When he runs in the sim card, the supportsBrowseForImage property is true indicating it is supported, but on the browseForImage() call, the application disappears. The callback is never called. I think I can see a gray bottom bar as if the app were reduced to a minimum, but I can't bring it back. Heck, I can't yet bring up the system menu. If I redeploy the application (which causes the previous uninstall) it seems to recover.

  I use FB Burrito and am, I changed the project settings to use the SDK.94. I use the simulateur.94.

  I installed TourDeMobileFlex found here: http://flex.org/TourDeMobileFlex.fxp

  The TourDeMobileFlex camera seems to work fine in the 0.9.4 Simulator. He opens the roll and you can choose your image saved previously.

  The CameraRoll of the TourDeMobileFlex code:

  
  http://ns.Adobe.com/MXML/2009.
  xmlns:s = "library://ns.adobe.com/flex/spark".
  paddingTop = "10" >

  
          
  If (CameraRoll.supportsBrowseForImage)
  {
  var cameraRoll:CameraRoll = new CameraRoll();
  cameraRoll.addEventListener (MediaEvent.SELECT, {function(event:MediaEvent):void}
  i.source = event.data.file.url;
  });
  cameraRoll.browseForImage ();
  }
  on the other
  {
  l.Text = "CameraRoll; not supported
  }
          
      
      
      
          
  If (CameraRoll.supportsAddBitmapData)
  {
  var cameraRoll:CameraRoll = new CameraRoll();
  var bd:BitmapData = new BitmapData (640, 480);
  bd.perlinNoise (640, 480, 1, Math.floor (Math.random () * 10), false, true);
  i.source = bd;
  cameraRoll.addBitmapData (comics);
  }
  on the other
  {
  l.Text = "CameraRoll; not supported
  }
          
      
      
      
      
      
      
  

• SMB: Browse the stock of broken android

  Hello

  Features: Ready NAS Ultra 2, OS 6.2.4

  Under OS 4, I could access my actions using android Root Explorer or ES Explorer of files on my local wifi network

  With OS6, using Root Explorer, I noticed, I can only go through the files, but I can't list the files they contain. Files in the root of the share are listed, but not downloaded. Basically, I can browse the folder structure, but I can not list all files.

  ARE leading Explorer gives error when access to sharing root folders: insufficient permissions

  Of the same actions with the same credentials work perfectly for windows PC

  Any solution to this?

  Your comments:

  I used the option "repair permissions" and set all permissions for each user again

  This resolved all the problems of access

  Something must have locked up all the permissions, now everything is going well for a few weeks

• Recover Photos from a broken iPhone

  I have an iPhone 5s that I dropped and cracked 4 times, about 6 months ago I dropped it and the screen did not crack just went black, with my music continues to play. I bought the iPhone 6 and left the children of 5 years sitting in my closet. Recently, I decided that I wanted to get pictures of her, so I plugged on my MacBook. The MacBook and my iTunes account picked up the phone, but won't let me download the pictures because the phone is locked. Yet once again, I put the phone in my closet waiting to get just the fixed screen. Today I took the phone to plug it into my Mac again and he has not read that and I didn't feel the vibration of this load. Is it still useful attaches? Other ways to get my photos? Help!

  The only way you're going to get your photos is if you have the phone repaired. On the Apple Store if more than just the screen is broken, your only option will be to make a replacement off-warranty but your photos will be gone. If you take it to a reputable 3rd party repair company in your area, they may be able to replace the screen and set the power connector for the phone can be charged and you can login with your password and retrieve your photos, but your eligibility for a replacement of off-warranty by Apple will be gone.

  It depends on what is most important to you.

• Blue Yeti works more when the upgrade to 10.11.5

  Wanted to ask if anyone else may have had this problem.

  Blue Yeti has been working flawlessly so that day, that I have updated to OX X El Captain 10.11.5 the microphone no longer works with Screenflow or Garage Band.

  It could just be a weird coincidence and blue yet Mic is broken. The led lights when it's plugged in, so it has the power. Any ideas on how to test it?

  Try to configure the yeti like new

  • Connect to Yeti with the supplied USB cable.
  • Click on the Apple-> System Preferences menu.
  • Select sound.
  • Click the output tab and select Microphone stereo Yeti under Select an audio output device.
  • Click the Input tab and select the Microphone stereo Yeti under Select an audio input device.
  • Out of system preferences

  If it still doesn't work try resetting the SMC reset management system (SCM) controller on your Mac - Apple Support

  I did not, but you can try another USB cable?

• My old iphone 6s is completely broken, it does not or registry that it is connected when plugged into a computer. I'm able to recover photos from the SIM card with an adapter USB SIM card or through any other way?

  My old iphone 6s is completely broken, it does not or registry that it is connected when plugged into a computer. I'm able to recover photos from the SIM card with an adapter USB SIM card or through any other way? I also do not save anything with AllAccess, icloud, or through my computer as you would with a digital camera.

  The photos are not stored on the sims, sorry.

  You can always try the Recovery Mode, little to lose at this point. If it doesn't, I suggest taking it to an Apple Store for testing.

  Recovery mode:

  Turn off your iOS device.

  Plug charge cable to the computer only (not to the device yet).

  Open iTunes on your computer.

  Hold the button to power on your device and do not let go.

  Plug the cable into the device while keeping the power button.

  Wait for the computer to detect the device and wait that he eat.

  Restore as New first, then restore sauvegardΘ if you wish.

  https://support.Apple.com/en-us/HT201263

• HP ENVY 1090ee 6 - left hinge broken

  I bought HP, Acer, Lenovo and Asus because I thought that the only thing that HP offers each time, is of exquisite build quality. However, today, I was met with a surprise. The left hinge (one near the power button) has apparently unravel, as if on its own.

  Surprised as I was, I contacted the technical support. Surprise, Surprise, my warranty information is wrong. Ive lost out on half a year warranty services.

  FLASH BACK: DUBAI - laptop bought on 3 February, 13 - great expectations.

  SKIP TO PRESENT: INDIA - lost hinge broken and guaranteed.

  Then I took a deep breath and open the HPSA faithful once again, inform the specialist my "fake date of purchase" (note that I am in India at the time). I am informed by the technician that I have 'support of the HP tech to the Arab Emirates UNITED to rectify the problem. '

  A STRIKE.

  Thus, everyone knows how 'good' the guarantee are services in India. I remember having an old all-in-one HP printer. The printer does not work, so we took to the "authorized" HP nearest after-sales service. The first day we went, we were not given any "service". The next day we went, that they claimed THAT NOTHING under the guarantee it covers. They could be right, but oh well, we paid for rectification.

  So now I feel like its going to be a repeat of the last time. And it's funny, because I found a large NUMBER of people having the same problem. I don't want to support the customer, waste BECAUSE I SAW them HELP OTHERS. The sad part is that these people are mostly from the States.

  Maybe its not justified, but it always seems like the developing countries get the worst of both worlds. We are the highest consumer population, and yet we get the inflated prices (I know are due to many factors beyond the control of the company) and poor service.

  I can't believe that there is not a single HP to Mumbai service center is, well, purely HP, and not a 3rd party "authorized dealer". I suppose that can't do anything on this subject and maybe as I write this in vain, but if someone is listening (or reading), may I suggest at least to have a third party service center. This will help a LOT.

  I hope someone can help me.

  AK

  

  Hey anand602,

  I'm very sorry to hear that you are experiencing this issue. I forwarded your case to the appropriate Department. You should hear from someone via private message in the next 24 to 48 hours.

  To check your private message, connect on HP forum. There will be an envelope at the top right next to your username.

  

• The HP Envy 15 t laptop: broken left hinge, corner of laptop is cracked and opened.

  Hello

  My laptop HP Envy 15t broken left hinge and the left corner is cracked and bulging. The laptop has not declined or fell. When I open and close the laptop the hinge moves and then separate tiny capitalization. The tiny screw are falling and I'm not able to close and open the laptop properly. The warranty has expired on this laptop. Help, please.

  Thank you in advance.

  @Albert5

  The question of the hinge on the Evny of HP is well known to HP, and yet they refuse to do much, if anything, to this subject.  If you are in warranty, they will typically set for free, no questions asked.  Out of warranty, however, it's like a completely different society.  They will be responsible of very varying amounts, from $130 to $300 to fix their own design flaw.   Here is a link to a long thread that I started to update others on the issue and my relationship with HP:

  http://h30434.www3.HP.com/T5/notebook-hardware/defective-hinges-on-HP-laptops-envy/m-p/5378336#M204440

  We hope that you will find useful information.  As further evidence that HP is aware of their own design flaw, the new 17 "want to have a case completely redesigned with a much better hinge.

  Good luck!

• Is broken on my Satellite A100-820 screen?

  Hello

  While my wife was using her cell phone yesterday, she suddenly had the horizontal and vertical lines of color (all kinds of colors, probably 1 or 2 pixels wide). I told her to restart, which lead to a total collapse of the monitor.

  When we turn it on now, turn on the right monitor, your stay in this way until it reaches windows (I can hear the sound of it to achieve the connection part). Then he gives me a few plots of different sizes of different bright areas. At the same time are again a few vertical lines. The amount of lines and spots changes at each restart, but as you can guess, don't see actually us all that on windows (or maybe we do, but it's all compressed in a few pixels wide).

  I tried to hook the laptop to our TV (it worked before) with a regular VGA cable. When I press Fn + F5 to the point where the laptop monitor turns off the coast and transfers to the TV (have to press twice for that), I just got a green horizontal line of the TV as well as a few other horizontal lines of a pixel.

  Initially, I assumed that the monitor was broken, but since I get no image on TV, I'm afraid, is something else (or several questions together).

  My questions boil down to this:
  1. is there anything else I can do to make the external monitor work? (Because I don't see anything, I can only imagine that I connect when I press the keys) I know that Windows still works, so if the external monitor could be implemented I would be fine for now...
  2. everyone guess (know?) what parts of the laptop are probably broken?
  3. can replace these parts?

  OK, so moving: I still have the same issues as above, but since everyone seems to be in the dark as much as I am, I have another question:

  I have a software that can only be activated x number of times (EA games) and one of them is on the laptop. Now, I can still boot into Windows, but I don't see anything. Is it possible that I can withdraw authorization or uninstall this software so I don't lose no (other) cd key?

  It would work even for connect the HDD (I checked, it's a SATA) up to a desktop computer as only the hard drive and start this way? The hardware configuration may be so different that it will invalidate my Vista installation and possibly even the validation of games with it. But it will allow me even to start Vista yet, or is it too hard to Toshiba cable material to do on a Windows desktop platform?

• How to backup without identifier (NFS vs SMB/AFP)

  Hello

  you just bought a ReadyNAS 312 but do not yet know about some basic principles.

  I want to use mainly as a backup destination, but also as the main source for backups Crashplan. In detail I will not install Crashplan headlessly on the NAS (totally not supported) but I prefer to install on my computer, which is then connected to the NAS through my line (just check, taken Crashplan supported files attached nas backups).

  What I don't understand is how can automatically make sure Crashplan can see the files at all times... I think that this should be easy with NFS and Linux computers. I just need to configure actions to be mounted automatically at each start-up, right?

  What, Mac computers, is even achievable with SMB/AFP so that I don't connect all the time in the Finder.

  I know that these sounds of questions a bit silly, but it's the first time I have use a SIN 'serious '.

  To be honest: sooner or later we will return only Linux boxes in the House, but at this point we can not yet get rid an Apple computer.

  Thanks a lot for any suggestion

  netghiro wrote:

  My initial confusion is related to how to automatically assemble the network shares on my system (the a CrashPlan possibly running) to make them available to the local backup software (which will take care to copy the files to the NAS)... Sorry for the bad wording or maybe you misunderstand something.

  http://support.code42.com/CrashPlan/latest/backup/Mounting_Networked_Storage_Or_NAS_Devices_For_Back... answers for OSX and links to a similar article for Windows. I suspect that for Linux, you simply create a NFS mount point suitable, but I have not tried. In any event, you don't really need to go with headless on the NAS installation, if it presents the advantage to avoid the need for a separate device.

  netghiro wrote:

  I think that when I'm on Linux and using NFS shares that will be easily magically mount every time you start (I still wonder if the username/password on the NAS must the same on my computer and to be honest, I was wondering the same for the two AFP/SMB!)

  With Windows, the name of user and password may be different. Configure you in the Windows Credential Manager. I'm not a Mac guy, but I think that Keychain Apple does the same for network with OS x resources. I think that with Linux, you need to explicitly use the opening of session and password in the mount command (I don't think it's the equivalent of the Windows or Apple Keychain credentials manager).

  netghiro wrote:
  I have already subscribed to a (computer) personal unlimited plan, I can envision the family upgraded but happy enough to save a little money as well. I'll try to keep a couple of good games of local backup in the first place.

  Which is what I did. I have an unlimited plan for single computer for the NAS. I use Acronis image to back up the disks of PC 'C' on the NAS and also to use the SIN as a consolidated storage. I have 3 copies local of all (the primary account as a NAS) use and maintain CrashPlan as expensive disaster.

  My pro - 6 has 2 GB of ram, which worked well for a few years, but eventually unlimited retention of deleted files caused central CrashPlan CrashPlan to run out of memory. This is what prompted the request for assistance to Crashplan. The solution was to the retention value of the files deleted in 6 months and then consolidate archive. That took a while (Crashplan was not wise to this point). I've also increased the memory in the pro and CrashPlan defined to use the size of the memory possible max (which, on the pro, is about 3.5 GB with a 32-bit JVM).

  It has been working fine since that date (end of June). In any case, it's a good idea to lower the setting for the retention of deleted files. I also put deduplication to "minimal".

• 2 on 4 broken USB Ports on Satellite A135

  One day I was on my laptop Toshiba satellite a-135 and my optical mouse began to blink.
  I unplugged it intends to plug back in and the problem fixed. When I plugged it back in, the light in mice did not illuminate, no computer has yet noticed it.
  Then I moved it to a different port, and he didn't notice it either. The other two ports on the right side of my laptop it recognized and worked.
  Physically, nothing broken or moved that I can see. In Device Manager it says there are 3 usb root hubs, and it says very well.
  I don't know how o fix this, and help is much appreciated.

  Thanks, brent

  Hello, Brent

  In my opinion this is the technical problem, and I'm afraid there is nothing you can do alone. I also believe that the verification of only ordinary material can say why these ports do not work. There must be a contact problem.

  I don't know where you live, but you need to contact the service. They allow to check the laptop.

• HP Officejet 6310: Broken printer HP Officejet 6310?

  When I broke the power connector HP Officejet, the cord of the HP Officejet 6310 to the power adapter, I broke the HP Officejet 6310. So I used a power connector HP Deskjet 1000 replaces the HP Officejet 6310 power connector, and when I plugged everything in, I got a reading on the screen HP 6310 power "Reset". Is my broken HP Officejet 6310? Or you do NOT know yet because the HP Deskjet 1000 power connector is not compatible with the HP Officejet 6310? Please let me know. Thank you!

  Hello

  The HP Officejet 6310 uses part # 0957-2175, which is

  http://www.Amazon.com/HP-0957-2175-AC-adapter/DP/B002MB9ERK

  and the HP Deskjet 1000 part #0957-2286, i.e.:

  http://support.HP.com/us-en/document/c02435664

  I don't think that the power supply for HP Deskjet 1000 has enough power for the HP Officejet 6310 or is not compatible. But we don't know or some other factors. You must spend $15 to buy the right power supply for HP Officejet 6310, this is the only way to ensure that it is still alive or not.

  Kind regards.

• Intel Centrino 1000 bgn wifi adapter 'broken '? (on Z570)

  On my new laptop (Lenovo IdeaPad Z-570), I have installed and working
  fine (for about 2 months now), as the dual boot between Linux and Win - 7.

  The wifi hardware is the Intel Centrino 1000-N, that plugs into the PCI-E card
  location of bus. (I had the large bottom plate and examined the)
  card, who has two sons, 1 white, 1 black and stands in his
  slot with a single phillips screw. [Seems that they can put "lock-tight"
  cement on the threads of the screw, the screw did not move.]

  Here's my current dilemma: 2 days, while that started under Linux.
  rather than tension, as usual, I closed the lid and went to bed.
  In the morning, at the opening of the lid, I realized... hmm... maybe it was
  hibernation (if I remember correctly).

  So, I turned it off and then cold started upward. The wifi was not see
  no signal at all. (Clearly the router/WLAN worked like my wife
  laptop connected fine.) I grew up in a cmd, su command prompt ' ed, and
  "iwlist scan" and has confirmed that there is a problem. Said that he could not
  analysis via the interface 'wlan0', because the network was down.
  I went in the ceni and walked through a re - configure and got:
  '... cannot be set without wire-flags... impossible operation, due to the RF-kill'

  Intrigued, I restarted, more to Win - 7, and she also couldn't see any wifi signal.

  I checked the slide switch on the front dash Panel... it looked very well.
  has been passed to the right. Slippery left causes an avant-panneau-LED
  to go off, slide the switch to the right, causing an avant-panneau LED to
  on. (I think I know that this switch controls bluetooth and wifi
  devices. I have not played with the Bluetooth at all yet).

  2 days ago, my conclusion was that the material 'broken' on the wifi adapter.

  But now, my "instinct" is the thought that maybe miss me another possibility.
  (for example a BIOS setting governs the wifi?) Could a misconfigured 'putting into hibernation'
  the installer put the wifi adapter in statehood "firmware-level/BIOS-level-disabled"?
  [for example such that neither OS can easily get the wifi adapter to see signals?]

  TIA...

  checked the fn + f5 to turn on the wireless?
  also check the updates to the bios download page if there is place.