24V switch signal detection

Similar Questions

• No signal detected from the monitor

  Hi all

  Built for computer spec - December 2005

  CPU-Intel P4 3.2 GHz, LGA 775, 640

  GPU-Inno 3D GeFORCE 6800GS 256 MB DDR3 PCI-E

  MB-ASSUS P5LD2 LGA775, Intel 945 chipset

  HD-MAXTOR WD5000AADS - new may 2011

  PSU-foxtail BN106 L7 530W-new in May 2011

  The last month replaced CMOS battery.

  I spent most of the last 14 hours or more trying to find a reason for the above message on my monitor BENQ FP71G + flat screen.

  When I turned on the computer this morning, it starts in Windows and office, but less than a minute, the screen froze.

  The cursor would not move and no buttons worked.

  I tried the button on the front of the case and the light on the monitor did not turn green.

  I lit it and upward came the message 'no signal detected '.

  I tried several times but I got this message each time.

  I had to use the "switch" on the front of the box to turn off.  I turned on and off several times - I could hear the pip MB and windows intro music but the screen don't start - it stayed orange [standby].  The activity light also flashes as Windows goes through commissioning.

  I tried to use the WIN XP SP2 disk and the disk of the software for the GPU at the start, but are recognized.

  I checked the monitor [with cable] on another computer and it works.  I have not tried another monitor on the desk.

  I spent a little time to read a lot of Google links [which most tend to all refer to each other] and have not found a solution, other than the suggestion that the GPU is deceased or the MB is dead [or both, if the GPU has overheated]

  I just found a link to the subject of this thread when you search forums answer.

  I'd appreciate it if anyone has a solution to this problem.

  Rgds

  Damascus [aka Antioch]

  Update

  I bought a GPU pretty fresh and install it solved the problem.

  In addition, I noticed that POWER supply was not as hot there just prior to the problem.

  Thanks to all those who gave their help.

  Rgds

  Damascus

• Don't monitor no signal detected after Windows update

  Hello

  I was using my pc and usually I tried to stop my pc but I had to download 1 update of windows required and then managed to download. When I came back all House, I can see is 'no signal detected' I tried to use 3 monitors up to now and always get the same answer.

  Just, I solved my problem out of my video card and replace it again. Thank you Niranjan

• Library meets live TV with the error: "there are currently no TV signal detected for this channel. The channel may be temporarily off the air. »

  I recently changed my TV card to an analogue of Hauppauge PVR150 at a Hauppauge DVB - S Nova S more. Media Center has worked well before.

  Media Library will recognize the new card, search and branch on 239 satellite channels, but may not display the channels giving the error message "there is currently no TV signal detected for this channel. The channel may be temporarily off the air. »

  I have installed WinTV 7 and that you can view all the channels very well in this program so obviously the map and the intensity of the signal are not the problem.

  In my quest through other forums, I heard problems re codec: mpeg2 and we tried several packs of codecs (including shark007) but with no improvement.

  My last move was to uninstall Media Center, uninstall all codec packs, uninstall the TV card and drivers, then reinstall the media library and the TV card and am still unable to view TV channels.

  Suggestions have greatly accepted.

  I've searched the Internet high and low for a solution to this problem and can lead to nothing more than what is proposed here by Divya.

  The problem seems to be fairly common and seems to be associated with codec. Most of the solutions I've come across related to the installation of media center alternatives and after several tries I finally opted for new version of Media Portal 1.1.0 beta

  Installed without a hitch and so far the interface is similar to the media library but has better customization and the ability to incorporate plug-ins.

  I did try the latest version (1.0.2) of the media portal, but said she had a few problems of stability (probably related to the W7 compatibility).

  Very happy now with Media Portal 1.1.0 Beta so will not need any other solution to this problem.

• Switch signals and Wireless does not work on Satellite A660

  I have laptop Satellite A660 17 M AND I am facing a PROBLEM THAT IS THE WIRELESS DO SWITCH NOT RUN AND did not SWITCH THE WIRELESS ADAPTER ON or OFF
  AND ALSO ON THE TOP OF THE KEYBOARD FUNCTION BUTTONS DOES NOT WORK

  AFAIK, the utility Vap and flashcard support are responsible for these functions. You can try to download and install them

  http://EU.computers.Toshiba-Europe.com/innovation/download_drivers_bios.jsp

  Note, first you must install the utility of vap and restart the support belt utility and Visual support cards, then

• Wireless signal detection

  I have a WRT160N router that I currently use. When I'm doing a my computer wireless signal, my router does not show up on top of the list. It is therefore on the list when I put up like WEP, but will not be displayed when I went back to WPA2. Does anyone have any ideas as to why this is happening? It happens even with my Google phone mytouch.

  Well, I think that in this case you have to modify some additional settings on your router. Follow the steps below and change the settings of your router.

  Open an Internet Explorer browser on your computer (desktop) wired page. In the address bar type - 192.168.1.1 and press ENTER... Let the empty user name & password use admin lowercase...

  For wireless settings, follow these steps: -.

  Click on the Wireless tab

  -Here, select manual configuration... Wireless network mode must be mixed...

  -Provide a unique name in the name box of the wireless network (SSID) in order to differentiate your network from your network of neighbors...

  -Set the Standard - 20 MHz Radio band and change the Standard channel to 11-2, 462 GHz... Wireless SSID broadcast should be enabled and then click on save settings...

  Please take note of the name of the wireless network (SSID) because it's the network identifier...

  For wireless security: -.

  Click the sub-tab under wireless > Wireless Security...

  Change the mode of WPA wireless security, encryption, select AES... Password input your desired WPA key. For example, MySecretKey, this will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone.

  NOTE: The password must be more than 8 characters...

  Click the settings advanced wireless

  Change the tag to 50 interval > change the Fragmentation threshold to 2304, change the RTS threshold to 2304 > click 'save settings '...

  Now let's see if you can locate your wireless network and try to connect...

• Satellite L30 - 113 - external monitor detects no signal

  Hi guys,.

  A little help needed here. I have a laptop Satellite L30 rather old and I have an external Benq G2222HDL monitor. I want to connect the monitor to the laptop, but I encountered some problems.

  Given that the laptop only has a video plug D - sub and the monitor has only a DVI cable, I bought an adapter. So now the DVI cable going into the adapter and the adapter goes into the socket D - sub of the laptop.

  The problem is that the monitor is always 'no signal detected '. I have set up the extended desktop display properties, but still nothing.

  What you think, where's the problem?

  HI sbi85,

  Usually, you can switch between monitors if you press the FN + F5 key combination. So, if you connect the monitor using this key combination. You see something on the screen?

  These adapters do not always work properly and I'd rather you buy a monitor with D - Sub port too.

  But in General, make sure that the devices are connected before you turn them on. At first power on the monitor and select the appropriate channel, then turn on the laptop.

• Wusb600n problem: no signal is detected

  Hey I have a problem here, so I recently bought a wusb600n for my office because I upgraded my router and wanted a faster connection. so when I installed this wusb600n there is no signal detected. I did reinstall the wusb600n but nothing has changed. I have been reading forums and nothing has helped. so I called cisco and they did the exact samething, I did and was told that a senior technician will help me the next day, which is today. No appeal was so now im, ask for help once more. This version 1 of wusb600n. Maybe the transition between wusb54GC messed wusb600n? So please help.

  things I checked that day:

  clicked on properties of the wusb and it says its working properly.

  tried to connect to a network and no signal is detected

  wireless laptop works so you can't exclude that my router is the problem

  Thank you

  OK so I found what is the problem, it wasn't the wusb600n it was my firewall, zonealarm.

• "No signal not detected" when using the monitor.

  Original title: Second just conked monitor

  I have two LG monitors with a desktop Acer running Win7Pro: Monitor1 (M1) = W2253 Monitor 2 (M2) = 23MP65HQ. All of a sudden yesterday stopped M2 display. It is said 'No signal detected' and goes to sleep. In the devices list, it is displayed as generic PnP monitor. When I check the resolution of the screen, it shows M2 in a small gray square, but it is not identifiable or traceable.

  It is the monitor or the cable. When I unplug M1, M2 is functioning normally.  So it seems that I can't use the two together no more. Except for a little while after the blackout. I opened a program had been posted on M2 before the failure of current and for a short time while M2 has been reactivated, but with a bad resolution. When I tried to set the resolution, the screen went black again and has stay black since. The display resolution is a constant problem before that. Sometimes he'd lose the setting and I reach the screen resolution and to detect and it would be fixed - just not always. An occasional pain but is not debilitating.

  There were no cases leading up to black screen - except a Windows Update. I didn't do any cleaning, moving, or adjustment of any sort, no power bumps or other external event. He became all black while I was doing a regular job. This is my work computer and I'm the only person who uses it.

  Help?

  Click on the following link and check if it helps.

  Update a hardware driver that is not working properly.

  http://Windows.Microsoft.com/en-in/Windows/Update-driver-hardware-ISN

• No signal is detected by the TV (KDL55HX800) using the HDMI source devices after the storm

  No signal detected by Sony Bravia TV (KDL55HX800-S/N 8114631) using the HDMI source devices after a storm last night.  Inputs RGB and components work fine.

  I have reset to factory default

  Installed the latest software/firmware from Sony site

  Checked the HDMI cables and selected the correct entries to the TV but even problem

  What could be the problem? At main / V Board? If so, what is the replacement P/N and where can buy it go? Link to store etc.

  Thanks in advance

  Hi mgkaundi!

• Digitization and adaptation of impedance of the signal source entries

  I'm trying to measure the voltage difference and the time between the two entrances of a USB-5132 digitizer. The switching interval that I try to capture is ~ 150uS and I intend to acquire ~ 25K samples (50MS/s for 500, although it is an overdose of sampling frequency). The digitizer is 1 M ohms entered and I wanted to use the 100 SMA 50 ohm cables to connect to the source of the signals which in addition to several kohm impedance. My knowledge of RF is low and I am concerned about the impedance matching between the digitizer inputs, impedance source and wiring. What kind of considerations to I need to avoid degrading the signal? The switching signal is pulse-like and is rich in harmonics and on a sample of 500K samples/s scope is represented accurately. Should what kind of considerations I do about the impedance?

  Hi William,.

  There will be some problems if you try to use a source that has an impedance of several kohms. You will probably get the reflections of signals. What is the source of your signal has several kohm impedance?  I'd take a peek through the following article Developer area that describes some of the considerations when it comes from impedance matching. Specifically, I would check the last section corresponding resistive. This should give you a better idea of what to worry about your application.

  http://zone.NI.com/DevZone/CDA/tut/p/ID/3475#toc4

  Here are also a couple more developer area articles that you might be interested in what concerns your situation.

  http://zone.NI.com/DevZone/CDA/tut/p/ID/5779

  http://zone.NI.com/DevZone/CDA/tut/p/ID/2892

  Chris W

• How do I auto detects the target using the trigger VBAI mode

  Hello world

  I had a vision system of machine ready to take choose using VBAI 2013 sp1.  Also, I use a sensor switch to trigger the camera to take pictures.

  When I type the loop running, it just won't continue to take photos no matther switch sensor triggers the camera or not.  I think it's the step that I used for the recording of the image, in the stage of registration of the image, I used picture newspaper still, but I don't want to use which is only what inspection status allows no other choice.

  So, how can I let the unit wait until he got the trigger of the alarm switch signal, and then take a picture and save the image?

  the stage of inspection to acquire the image, I used the trigger mode and everything worked fine, except the time error settting upward, I used 5000ms and if I put bigger like the 50000ms, VBAI turned really slow and showed time out error.

  If anyone can help me on this matter?

  Thank you

  You can use the diagram States-transitions to go only in a State based on the result produced by some steps.

  First, remove the registration step of the image of the State to check with you get the image

  Press Ctrl + E to turn the main view on the state diagram.

  Right click and create a new State.

  Right click on the State to inspect and create a new transition to this new State.

  Double click on the transition to edit it.

  Choose to acquire the Image - waiting time and set the condition false, to spend in this state when there is no timeout.

  Move the default transition from that State to the final State.

  Click on the new State to select it, and then add the image registration step.

  Using a state diagram, you have programmed an inspection that will record the image when there is no timeout.

  The State-transition diagram is a powerful tool to add a logic, branching and looping of your inspection.

  Open the tutorial 5 - state diagram Branching.vbai and tutorial 6 - State chart Looping.vbai for examples on how to use it.

  I hope this helps.

  Christophe

• Windows Media Center showing no TV signal

  When I go into WMC I select a television channel of the electronic Program Guide and WMC is back with a message:

  No TV Signal: There is currently no signal detected for this channel TV. The channel can be temporarily off the air, or you need to maybe adjust or reconnect your TV antenna.

  Problem with WMC > TV > Live TV > no TV Signal

  Here is a summary indicating the State of the map CableCard.

  Status of CableCARD

  The card manufacturer: Motorola
  Authentication of maps: success
  Activation of the card: success
  3DES encryption: support
  OOB frequency: 75,250 MHz
  OOB Lock: 2,048 Mbit/s
  Signal strength: 100% (2.1 dBmV)
  The quality of the signal: 100% (41.7 dB)
  Channel list: cablecard-oob

  When I go to HDomeRunSetup and try to do a scan of the CableCard card for all three tuners it again relates that the device/card is not the list of channels. I checked the cable connection and LED a green identity card.

  Where should I go from here?

  Hello

  • You did it all changes before the show?
  • What version of Windows are you using?

  You can stop the recording manually by double-clicking on the program and then click on stop recording. If the problem persists, try restarting your computer.

  Step 1: Check if there is an update available for Windows Media Center on your computer
  a. see the updates Windows Installer
  b. install updates and restart the computer.
  c. check the difference.

  Step 2: check if there is an update available for your TV tuner card
  see automatically get recommended drivers and updates for your hardware .
  b. install the update just for your device and restart the computer.
  c. check to see if the problem persists.

• How to use a switch connected to the DAQ card as a source of events in a Structure of the event

  Is easy using a switch on the front panel as a source of events. However, I like to use an external switch electrician on my card for the acquisition of data (NI PCI-6229) as the event source in the Structure of the event. Can anyone help?

  Happy New year to you too!

  Attached is an example in BT 8.5

  • It uses the time-out loop (running every 100ms) to simulate your reading of the data acquisition card.
  • A shift register is used to keep track of the previous value of the switch.
  • When a change of the switch is detected, the user event is raised and the display will show the new State.

  Running the vi with activated highlight performance can be useful.

  Steve

• Loss of signal tv on a touch smart 600

  Choose 'play live TV' in the 'Windows Media Center' now leads to a snowy screen. Enter 003 on the PC error message remote returns: "no TV signal detected for this channel. You need to maybe adjust or reconnect your TV antenna. "We have called cable TV company, but said that they"no longer support"of customers who watch TV on a PC, so they cannot guarantee that any technician they send will be able to solve the problem. Someone there to solve a similar problem?

  Hello @RobNJ101,

  Please update me on your subject. Well, since you now know what is causing the problem, I suppose that the decision is to replace it or not. The part number for the TV Tuner on your computer are easy to find by simply searching online for the part number is 594509-001 When the room is not really that expensive I'm you offering instructions below on how to replace:

  Step 1. First, you must remove the following components of the computer.

  • The hard drive and memory cover
  • The stand
  • The cover of the e/s
  • The feet
  • The back cover
  • The shield of the amp Board

  

  Step 2. Remove the shield from the motherboard.

  

  Step 3. Detach the connectors of module e/s USB on the side of the motheboard...

  

  Step 4. ... and pull them out of the way for easy access to the card.

  

  Step 5. Remove the antenna connector and the audio-video Jack of the card.

  

  Step 6. Remove the two small screws of the minimap.

  

  Step 7. Remove the card.

  

  To the Board at an angle just the card at an angle of 45 degrees when put in and reverse the previous steps.

  I hope that I have answered your question to your satisfaction. Thanks for posting on the HP Forums. Have a great day!