5508 WLC and associating 1242

Similar Questions

• iPhone/iPad connectivity problem with of 5508 WLC

  Hello

  We are implementing a new Cisco 5508 WLC and C3602I LWAP corporate wireless network. Us are not running no matter what RADIUS or EAP for now and start with WPA2 / AES with a pre-shared to start flying.

  The question that we are conducting is based iOS devices (iPhone/iPad) don't seem to want to connect. We just get one couldn't enter wireless messages. We had success with several portable Windows-based, my MacBook connects, as well as several different Android devices.

  Looking at the logs on the WLC I see those entries that correspond to the MAC address of my iPhone.

  * apfMsConnTask_6: 17:25:20.620 Jul 17: % CSA-3-CHECK_SUPP_RATES_FAILED: apf_utils.c:376 could not check support rate. Lack of support rate. Length: 0 mobile MAC: 24:ab:81:92:4 d: 97.

  Does anyone has any ideas or have encountered this problem before?

  Any help would be greatly appreciated.

  Thank you!

  Andrew

  What is happening with several iDevices?  Can you try to restart one of these iDevices, because there seems to be a problem with the unit and not the wireless.

• 2006 WLC and 802.11n

  I have a 2006 WLC with 6 1242 APs and wondered what should I expect when I can replace 1242 a 802.11n AP.

  I know that the new access point will not work at full speed, but other than that, I don't know.

  Any ideas on that?

  Thank you, Gary

  So I can add an 802.11N AP to the controller
  

  802.11n AP only, you can use is the 1250.

  BUT it will not run at the N speed, etc.  Right?
  

  You can activate 802.11n, but because the controller has speed 10/100BaseTx, then you have a bottleneck.

  So what we're thinking is purchasing 1 or 2 of the APs and let them run on our 2006 WLC, knowing that i WILL not see the speed difference, etc until next year, when i get the new WLC.
  

  You do not things easy for me are you?

  Ok.  So that you know what your next financial bucket will come in.  What your savings.  1250 in a desktop environment... Hmmm... I don't recommend it.  1250 need 20.0 watts of power (because you are running firmware 4.X).   IF you use either a switch that can pour 20.0 PoE power, a power injector or remove one of the radio modules.

  If you, for example, the baby 1040 (aka "N") or more the 5508 1140 then you can really run 802.11n.

• 5508 WLC works only with small business unit SA 520 security

  Cisco 5508 is new Wireless LAN Controller supporting 802.11ac new Giga bit wireless. It has been connected to the port of SA 520 LAN LAN port of small business Security Appliance (trunk). VLAN by default 1 works fine, which is for the management but vlan data does not work.

  However, I can ping from WLC until SA 520 on vlan data but no ping SA 520. Also the wireless clients connected to the AP cannot connect to SA 520 on the data vlan 2702 as gateway?

  both have the latest firmwares. These devices are supported?

  Any suggestion?

  Hello

  I guess your VLAN DATA is another VIRTUAL local network that you have configured on the WLC.

  Make sure of the ff.
  1. you have configured the correct WLAN interface
  2. you have assigned the right WLAN interface on your SSID
  3. the DHCP of your users (where btw?) if in the WLC, check if it is on the correct subnet and that it is enabled

  Also considering it is a safety device, check that the ff:
  1. you have configured the necessary policies and fro the AP and WLC
  -Note that traffic CAPWAP able, to avoid any problem, just allow and fro WLC and AP for example, two policies a WLC-> AP and another AP-> WLC

  2. of course, the policies necessary to allow traffic

  PS: The compatibility is not a problem, note that your servers SMB of device as a connection of the WLC. You should have no problem integrating the two

  If it is not much, kindly rate helpful messages :)

• ISE 1.2 rejects 5508 WLC RADIUS messages

  The setup of ref is:

  WLC 5508 HA pair running 7.6 talk with ISE 1.2 patch 7 (a 6).

  Wireless users are authenticated very well, so the 5508 is a valid n in ISE, but...

  When I install active RAY of relief, so that the WLC can query the ISE Server I get the message:

  "The query a device no RADIUS wireless was interrupted because the installed license is for wireless devices only.

  Why the ISE spend a RADIUS of a WLC message which is a wireless device?  It is certainly a mistake?

  Hi Nicolas,.

  This is a known fault.

  CSCug34679    ISE drop keep alive from WLC.

  Symptom:
  ISE drops keep living authentications from the WLC, with message 11054 request from a device no wireless because of the license installed wireless.
  Conditions:
  When only licensed wireless is installed on the ISE and use current keep alive on the WLC.
  Workaround solution:
  Passive use keep alive on the WLC and non-active.

  Kind regards

  Jatin kone

  * Make the rate of useful messages *.

• unloading of feature to make dhcp off the WLC and put it on Active Directory.

  I need to use the feature of unloading to dhcp off the WLC and put it on Active Directory.  Someone at - it a walkthrough or a page for this?  I know it's just a checkbox and a redirect to the new dhcp server, but where the hell is the configuration on the WLC?

  Thank you!

  -anne

  You can go there.

  http://www.Cisco.com/c/en/us/TD/docs/wireless/controller/7-4/configuration/guides/consolidated/b_cg74_CONSOLIDATED/b_cg74_CONSOLIDATED_chapter_01001001.html

  Point to your existing ad integrated DHCP server.

• Recover the forgotten password already created WLAN in 5508 WLC

  Hello

  Is it possible that we can retrieve the forgotten password already created WLAN in 5508 WLC. I do not want to reset the password want to only see the existing password. Image is attached as a reference.

  Kind regards

  Muhammad Noman

  Hi Muhammad,

  I don't think that it is possible that the key is encrypted in the configuration files as well.

  See you soon,.

  Ric

• 4402 WLC and WCS

  Hi all

  We have 3 WLC 4402 all with identical config and we use Lobby Admin to create guest accounts.

  Problem with this is that the guest account must be created on 3 WLC.

  I installation WCS and want to know how to extract the 3 existing wlc and their config in the WCS.

  Can the admin of lobbay can create accounts on the WCS and grow them into all wlc

  Hi RR,.

  >I install WCS and want to know how to extract the 3 existing wlc and their config in the WCS.

  It's pretty easy. You must add a new controller via the configuration-> page controllers. The option 'Add the new controller' is in the drop-down list at the top right of the screen. You can use a list separated by commas of IP addresses to add all three at the same time. WCS audit of the controller software and get to the bottom of the config.

  >Also can the admin Hall can create accounts on the WCS and grow them into all wlc

  I have not used the account Admin Hall (it is not really appropriate in the office where I work), but I know that you can create a guest account in the controller model launch pad. It is under Security in the sidebar. This model can then be applied to all three WLCs at the same time, that will simplify things. I guess you would need to make sure that your Hall administrator can access this particular part of the WCS.

  Hope that helps.

  -Jason

• Cisco WLC and Apple TV Hello

  Hello

  I followed the guide on http://www.cisco.com/en/US/docs/wireless/technology/bonjour/7.5/Bonjour_Gateway_Phase-2_WLC_software_release_7.5.html on activation of Cisco WLC 7.5 with Apple TV good morning however I have a weird problem. I have some clients unable to see the apple TV connected to a different wireless access point while some may see the Apple connected TVs. I have attached my setup for reference. I would like to inquire about the use of LSS and so perhaps someone has encountered similar problems? The apple TV is discovered by the wlc on mdns-domain names.

  According to the document, multicast has been activated not however the discovery of the apple tv is intermittent of apple customers. Customer can discover apple tv 1 and 3 but not apple tv 2 and sometimes it can discover all 3 apple TV while client B is able to perceive all apple TV devices 3. All 3 apple TV devices are discovered by WLC and only apple TV service has been activated on WLC.  I was wondering if anyone has seen a similar question? Not too sure what can be the cause of it?

  Any suggestion is appreciated.

  Some of the docs didn't do it, but it is required as all my installation requiring Hello, set multicast implementation.

  Thank you

  Scott

  Help others using the system of rating and marking answers questions like "answered."

• What files can I save items v13 so that I don't have rebuild my photos and associated keywords.

  Elements v13 8.1 on windows using.  I reinstall windows 8.1 on a new hard drive.  What files can I save items v13 so that I don't have rebuild my photos and associated keywords.

  dueker1 wrote:

  to clarify-> method recommend you will save the keyword structure.  For example, my keyword structure is 6 deep layers.  My concern is that this method will maintain this depth of information.  I don't want to rebuild.  Thank you, Jimbo.

  The backup process in the Organizer stores your image files as your current catalog in a backup folder. The restore process is able to recreate your tree image files as well as your catalog either on the original on a new location. All the information in your catalog are kept including your hierarchies of tags or albums. Just choose the location for the restore, the restore process is to restore the tree of photo files as well as the creation of a new, updated, with the same catalog structure.

• Entities and Associations - Association error objects

  Hello

  I am new to develop in JDeveloper and I am currently following a tutorial with the Oracle members database use for their tutorial. Now I'm following this tutorial (Oracle JDeveloper 11 g Release 2 tutorials - rich in development of Web Applications with Oracle ADF)

  My problem is that when I try to create entity objects and Associations based on the tutorial, my AppModule does not create the association departments-> employees as you can see on the subject of 20º to the link (the Appmodule running the EmpDeptFkLink1view).

  I tried many things to fix it and I try it on my localhost database (not an oracle database).

  Given that this association is not created, the AppModuleDataControl isn't the control needed to create the jsf page in the next step.

  If you have all the help you can give me, please reply to this message.

  I use jdeveloper Studio edition version 12.1.2.0.0.

  
  

  Hope that my problem is clear enough.

  Thank you very much!

  Greetings,

  Frederico Barracha.

  Frederico,

  Associations are created automatically when the database table has a foreign key.  Check your local host database and make sure that there are foreign keys.

  If this isn't the case, you can manually create links and associations.

  Ray

• LR5 not showing Panel 'region' curve tone and associated with cursors.

  Hello

  Panel curve of the LR5 tones as it is set up is not displayed the Sub-group of experts 'Région' and associated with cursors.  It is not also show the slider immediately under the tone curve itself.  Any ideas on how to get these features to show?

  Thank you

  Hi Jao,

  Bingo!  Who did the trick.  Thank you very much.

  Ian

• Option button and associated features does not work!

  Hi Pros,

  I am facing the following problem:

  1.I have an interactive PDF created in Acrobat 9 Pro.

  2 have a few option boxes, each radio buttons be assigned been worth (for example: 1,2,3 etc.)

  3.I have a text box in which the value of the selected option button is displayed.

  4 PDF works fine on my machine.

  5. customer is to have Internet Explorer version 7.0.5 and Adobe reader: 8.2.6

  6. the option boxes and associated features does not work on the client computer.

  7. the text box displays "0" even if we have a radio button with a value of 2 or 1 is selected.

  What is the problem? How can I solve this problem?

  Help, please.

  If you have disabled JavaScript or automatic calculations in Reader preferences, you will get this type of behavior. You can test yourself by changing your preferences (Edit > preferences > JavaScript, Edit > preferences > forms > automatically calculate field values). All calculated fields depend on JavaScript behind the scenes.

• difference between link and association

  What is the difference between the association and the display link?
  
  How dose see links work?

  Hey Danny,

  Links has an explanation on the view links and associations:
  Links: http://download-uk.oracle.com/otn_hosted_doc/jdeveloper/1012/bc4j/intro/bc_avl.html
  Associations: http://download-uk.oracle.com/otn_hosted_doc/jdeveloper/1012/bc4j/intro/bc_aassoc.html

  In short, show links concerns two objects view and associations of two entity objects. There is no link between the two, but links can be created based on associations or independently without associations.

  Jean Lou

  Published by: Marc Israel on November 19, 2009 01:26

• Problem with NAC and 5508 WLC OOB

  I have a wlc 5508 to shared resources to a 6500 switch. Shared resources to the switch on eth0 and eth1 is also the CASE. The CAM is connected to an access port.

  The SCS and CAM are on VLANS separated and the CASE has been added to the CAM without problem.

  I followed the example of document for OOB WLAN (VLANs and mapping etc.), but I don't get all current identifications. The client is associated and the WLAN interface is the quarantine VLAN but it seems that the client can connect to the network without problem (may web access a server in-house to campus)

  The customer indicated in customers wireless on the device of the cam page

  If I either CASE interfaces close client connectivity is broken.

  Once, randomly the own access connection Page appeared on the client (battery dead and waited for about an hour) but when I rebooted the CASE check it was she never came back.

  I do not set up the SSO part, must it be filled or is it a valid test without it so far?

  No idea where to start with this problem?

  Thank you

  Yes, it looks like that somewhere, your 'placing in quarantine/no authenticated' vlan is filled to the full network, I do not see another explanation.

  Try to configure the WLC for a new vlan quarantine which does not exist anywhere.

  Then you should not have any access at all to anything whatsoever. Then try to leave this vlan gradually reach the heap and constantly test. You should find the point where the vlan 'flows '.

  Nicolas

  ===

  Remember responses of the rate that you find useful