A60 SP does not start

Similar Questions

• Satellie Pro A60 EN does not start

  My satellite Pro A60EN does not start. When I turn on the power there is a slight click, but it does not read the disk. If I boot with a bootable CD, it starts the CD/DVD drive, but does not start. The HARD drive is OK, as I tried it on my desktop (using an IDE USB connnector).
  East - the CPU, motherboard or RAM?
  Any help much appreciated.

  Hello

  To find out what s wrong some diagnostic tests are needed.
  If you checked the HARD drive and if it s ok so I guess there must be something wrong with the motherboard. But it is worth checking to be sure 100%.
  The fact is that the motherboard is an expensive piece and you should check it out before you replace something.
  Sorry I put t see any other solution.

• Satellite A60-672 does not start after upgrading memory

  Hello

  I bought an additional memory for my laptop, but after installing it the PC will start is no longer, when I turn it on it makes a brief noise then nothing. After taking the memory expansion out again once, the laptop still does not start.

  Peter

  Hello

  I agree with "guy sos." There is no doubt motherboard problem now. I assume you used the incompatible memory module.

  In any case, contact the after-sales Service of Toshiba partner in your country and explain to them the situation. The address that you will find under http://www.csd.toshiba.com/cgi-bin/tais/su/su_gaspLocator.jsp?pf=true

  Good bye

• Satellite A60-106 does not start

  Can anyone help? When I turn on my A60 106 it happens with a text screen that says Windows (XP) will not start and a few basic instructions. There are 5 options listed - Safe Mode - Safe Mode with network - safe mode with command prompt - known last good configuration - and start Windows normally. None of them work, computer goes to the Windows XP logo normally then flashes to the toshiba logo, after what the power seems to cut and it is up to the text with the options screen. Which if left constantly looping. All the ideas!

  Hey Warren,

  Whenever I encountered this behavior it is always caused by a defective hard drive. Indeed the system cannot be loaded because the required files can be read from the HD.

  You can try to re - install your recovery CD system in the hope that it is just the files that have been corrupted, but if this also fails then a new HD will be required.

  concerning

• Satellite Pro A60 EN does not start after you have used the recovery CD - isapnp.sys missing or damaged

  Help am stuck with it.

  Necessary to perform a recovery on the laptop and used the recovery CD 2 they seem to work OK. No error during installation, but after that they finished and it restarts didn't get the following message.

  Windows could not start because the following file is missing or corrupt:
  System32\drivers\isapnp.sys

  You can attempt to repair this file... etc but I don't have any original installation CD all have is the recovery for the Toshiba.

  I have a setup of Windows XP for the PC disk, but when I try to run which, but it starts just the configuration. Setup is loading files and after the kernel debugger get error

  "File ntkrnlmp.exe could not be loaded.
  The error code is 4, sometimes it's 7.

  I tried to delete and recreate and formatting partitions, so I can see and I can copy a file to the C: drive

  So any suggestions as to what wrong here

  Thank you very much

  I put t know if this Microsoft Knowledge base article would be useful for you, but you should check it out.

  [You receive a "Windows didn't start because the following file is missing or corrupt: Isapnp.sys" error message at startup | http://support.microsoft.com/kb/315311]

  Microsoft has a solution, and I would like to know if you can solve this problem by following the steps of the solution described in the article.

  Feedback would be much appreciated

• Ieee 1394 host controller Texas Equium A60-692 does not start

  Hello!

  I have a Toshiba Equium A60-692 about 2 years old. On rare occasions the above will install and also the network/ethernet card etc with it when it starts. But 99% of the time it fails to start upward.

  Tech from Toshiba tell me it's the CMOS battery, but time slept OK for the last week so maybe it could be something else. Other strange things are can only recognize the drive HARD to start from what IDE Standard is chosen in the BIOS options (Enhanced IDE option and I think only used normal overall, ups causes boot errors). Also a green screen with weird graphics on occasion. Also the speed of the processor can be reduced, as shown in the properties of my computer.

  Any ideas from anyone as worried of wasting time to unsolder the battery if this isn't the problem. Could this be a fault of the motherboard that is irreparable? I am a relative novice if need help someone here. This made me!

  Hello

  I think you might be right. Eventually he s a small part on the motherboard that could malfunction.
  If I m not mistaken the controller IEEE 1394 Texas Instruments could be the Firewire port and it s part of the mobo

  Welcome them

• Equium A60-173 does not start after the BIOS update

  Hello people,

  I downloaded a BIOS updated toshiba for my Equium A60 - 173 and while it was loading on, restarted my laptop. Now, whenever I turn it on, the power light comes on for a few seconds, there is nothing on the screen and then it turns off again. I'm really worried, I've done some serious damage. I know a bit of the BIOS, but not that much. I need help, this is how I put a BIOS on here if I can't turn it on and the current one is damaged. Is it possible to get the loaded BIOS on without being able to turn it on?

  Any help will be greatly appreciated! Thanks in advance.

  Concerning
  James

  You could try to remove the battery, wait 2 minutes and then go back, however he only its not very likely that your BIOS update was not successful. If I remember correctly when I flashed my A60-181 this process takes about 10 minutes. If your laptop prematurely reloaded until the program has finished, I'm afraid you have no choice but to send new to Toshiba to be fixed.

  Richard S.

• A60 Windows XP does not start

  When XP does not start, he spends just continually rebooting.
  None of the options to restore the last known good configuration or from different modes of security work.
  The error message is:-
  UNMOUNTABLE_BOOT_VOLUME
  The Microsoft Knowledge base says that XP CD-ROM to access the Recovery Console is necessary before running chkdsk/r, but because XP was installed by Toshiba OEM factory, is not available.
  Can someone guide me to a solution.

  Dave Cox

  Hi Dave,.

  If you don't already have a bootable CD, then you will need to create one (using another PC of course). Try to Google for "Ultimate Boot CD". It contains many tools and utilities and can even be bought if you don't have the means to burn your own version.

  You will need the means to back up your data once you have access to your HARD disk, although you can see as you drive is inaccessible in any case. This will depend on exactly what the problem is with him.

  To boot from the CD (without changing your BIOS) Toshiba have a shortcut. Simply hold down the 'C' key while turning on your laptop and the device will try to boot from the CD-ROM. It also works with the recovery CD.

  Good luck

• Siri does not start under macOS Sierra

  I've recently updated to macOS Sierra (public version) and everything seems fine, except for allowing to Siri. I tried to enable the system preferences as well as execution of the Siri application in the application. I even tried to 'facilitation' by selecting in the menu bar.

  In any case it does not start. Upon activation in system preferences, I get "There was an error in the preferences of Siri." and it takes back me to the main view of system preferences.

  Y at - he of the log files that I should be reviewed to determine the cause of this problem?

  Thank you

  Steve

  Same thing here on a MacBook Pro (13 inch, late 2011)

• Black MacBook does not start

  I have a 10 year old black Macbook, which does not start when a battery is installed.  If it is connected without battery installed, it lights up, but if there is a battery in it, even if it is plugged in, it will get the startup sound and the screen of the Apple gray, then turn off.  I got a new battery and charge it where the charger turned green, but the results are the same.

  Any suggestions?

  It is difficult to say what is happening with this machine, since the time and wear are considerations. I don't know what version of the operating system that you use, but there is a sequence of things you should do - in order of severity.

  http://www.howtogeek.com/217158/what-to-do-when-your-Mac-won ' t-start-up.

• iPhone hot 5s fees and does not start

  phone is connected to the load.  After a while I checked it and it was very hot.  I unplugged it and now it does not start.

  Have you ever tried to force reboot the phone by holding down the button sleep and home for 10 seconds, until the Apple logo comes back again? You won't lose data.

  More troubleshooting can be found in this article:

  If your iPhone, iPad, doesn't respond or won't turn on - Apple Support

• iMac does not start after the last security update

  Hello

  After the last update my iMac (late 2009, El Capitan) does not start.

  The iMac starts he accepts my user and password entry, the loading bar stops at 80% and then nothing happens... after I turn off the iMac. Repeating this procedure change nothing.

  Does anyone have any advice for me?

  THX

  INTELLECTUAL PROPERTY

  a solution that helped me:

  Re: security update causes damaged Apps

• iMac does not start after 10.11.6

  Since the 10.11.6 patch my IMac does not start with my hub plugged.

  Everyone

  I assume you mean a USB hub? What does do when it's plugged in? It starts successfully when the hub is not plugged? If so, I would say that something is wrong with the hub or there is a problem with the port it is plugged or something plugged into the hub.

  Try to plug it into a different USB port on your Mac.

• MacBook Pro does not start

  I have tried several things but the laptop won't start do not. Power cable showing green light as if the laptop is fully charged. It's like the death does not start.

  Try resetting the SMC

  Reset the management system (SCM) controller on your Mac - Apple Support

  You said "It's like death does not start."

  Does this mean that he shows no signs of life? Indicator light power?

  Hear the carillon?

  Hear the fans?

• The FireFox 42.0.1 application does not start.

  The FireFox 42.0.1 application does not start. I can uninstall and reload FireFox 37.0.2 and that worked, but now when I load 37.0.1 it installs really 42.0.1 that no longer works.
  I had to use IE 10 to contact Mozilla.
  Year annual should be ashamed of this...
  Can you tell me why Mozilla FireFox 42.0.1 installs but won't work?
  In addition, why FireFox 42.0.1 install when I try to install 37.0.2?

  It is possible that your firewall or other security software blocks or limit Firefox or plugin-container process without informing you, possibly after the detection of changes (update) for the Firefox program.

  Delete all rules for Firefox and the plugin-container in the permissions list in the firewall and allow your firewall to ask permission to get access full and unrestricted, again to install for Firefox and the plugin-container and the update process.

  See:

  • https://support.Mozilla.org/KB/server+not+found
  • https://support.Mozilla.org/KB/firewalls
  • https://support.Mozilla.org/KB/fix-problems-connecting-websites-after-updating