Absolute optimum req to PC for CC configuration

Similar Questions

• You don't have enough privileges for the configuration of the connection properties. Contact your administrator

  When you attempt to connect to the VPN Aventail I get th e following in a "Connection error" message box: "you don't have enough privileges for the configuration of the connection properties. Contact your administrator. That this connection has worked before. I suspect a MS patch for breaking it. Any help would be appreciated.

  We have solved the problem yesterday, by simply reinstalling the Aventail software.

  I spoke to network administrators and nothing had changed, so it's quite strange.

  anyway thanks a lot for your help Brian.

  See you soon,.

  Tobias

• Router Cisco 1801 for PPPoE Configuration

  Hello

  We have 1801 router and you want to configure for PPPoE.As our ISP provided ADSL connection with the following parameters:

  Encapsulation: PPPoE

  Multiplexing: LLC based

  VPI = 0

  VCI = 103

  Login = xxxxx

  Password = xxxxx

  IP: Dynamically by ISP

  I'm new to configure cisco router. Please say we follow the steps in 1801 for above configuration cisco router configuration.

  Hey Hamza Rahab,

  Thank you! Please add the following to your configuration after replacing the your_login and votre_mot_de_passe with your real ISP credentials (enter the first configuration mode using the commands Activate and Configure terminal ):

  ip routing
  ip cef
  interface atm0
  no shutdown
  pvc 0/103
  pppoe-client dial-pool-number 1
  interface dialer0
  dialer pool 1
  encapsulation ppp
  ppp pap sent-username YOUR_LOGIN password YOUR_PASSWORD
  ppp chap hostname YOUR_LOGIN
  ppp chap password YOUR_PASSWORD
  ppp ipcp dns request accept
  ip address negotiated
  ip nat outside
  ip mtu 1492
  ip tcp adjust-mss 1452
  interface vlan1
  ip address 192.168.1.1 255.255.255.0
  ip nat inside
  no shutdown
  ip access-list standard NAT
  
  permit 192.168.1.0 0.0.0.255
  ip nat inside source list NAT interface dialer0 overload
  ip route 0.0.0.0 0.0.0.0 dialer0
  ip dhcp excluded-address 192.168.1.1 192.168.1.10
  ip dhcp pool LAN
  network 192.168.1.0 /24
  default-router 192.168.1.1
  import all
  

  This configuration should

  1. connect to your ISP by using the login and password you were assigned (replace the your_login and votre_mot_de_passe with your real credentials for the ISP connection)
  2. begin to assign addresses to the network 192.168.1.0/24 IP LAN clients, starting with 192.168.1.11
  3. perform address translation network needed to allow access to the internet

  Please try and let me know if it worked. Thank you!

  Best regards

  Peter

• Where is the log file for the configuration of the plugin to a vco part?

  Hello

  I have a vco plugin that has a configuration interface, basically, everything works fine, but I can't find the logs for the purposes of Web configuration. I thought that newspapers could be found in Server.log (in my case, the exact path is C:\Program Files\VMware\Infrastructure\Orchestrator\app-server\server\vmo\log\server.log) but they were not there.

  I checked a few other plugins vCO well known as the SSH plugin, but I can't find the newspapers for his configuration interface, either.

  Can someone let me know if I'm looking the wrong log file? Thanks in advance.

  To the vCO 5.1 you can check in {vCO_INSTALL_FOLDER}\configuration\jetty\logs\jetty.log

  And log4j.configuration I think is in {vCO_INSTALL_FOLDER}\configuration\jetty\resources\log4j.xml

• Oracle Virtual Directory for SSL configuration

  Hello experts, can you please help me understand whether a typing error in Oracle Enterprise Deployment guide for IDM http://docs.oracle.com/cd/E25054_01/fusionapps.1111/e21032/toc.htm#BEGIN, port of the OID is mentioned in Oracle Virtual Directory for SSL configuration - section 9.4.2.2. Why port ODI?
  
  The guide mentioned how to configure OID for SSL in section 7.4.3.2 and here he mentioned port 389 OID! For example, during Setup for OVD, is not that we are supposed to talk about port OVD. Please help me clarify this confusion. BTW, in many places, the guide says clearly, if you have OVD, you mention port OVD here...
  
  Thank you
  Jyothi

  Specify the port OVD. I think that by default it's 6502.

  Kind regards
  GP

• Recommendation for the configuration of the disk

  Recommendation for the configuration of the disk:

  A wide range of RAID 5 consisting of 8 x 146 GB drives?

  Two arrayys of RAID 5 with 4 x 146 GB drives in each table one would be used for the data store, and the other would be usd to images of backup to it.  The idea here is that when we do backup via the script GhettoVCB/o would be mainly on the secondary RADIUS and not the main data store.   In my opinion?  I think I have the only RAID 5 Bay with all the readers of 8 x 146 GB for a data store single should surffice.   I don't think the performance problems will be that detrimental.

  Do not hesitate to offer advice on scenarios, thank you

  Engineer accommodation

  ModusLink Open Channel Solutions, Inc.

  As written before, depends on the type of e/s.

  With more than R and W low, RAID5 (on multiple disks) could be very good.

  But don't forget to also use a global hot spare, degraded performance a RAID5 mode could be dramatic.

  And don't forget that your controller has a battery backup.

  André

• Open Document icon missing IN Reqs but work for POs

  Hi all
  If there is point of sale and PO requests that are waiting for your approval. You would typically go to the purchase of super user-> summary of Notification-> task list, choose po/poreqs-> click Open the document to view/make changes before approval.
  
  Open Document link is woking when you open POs but lack of PO Reqs. I went through many documents such as (Metalink doc 356969.1). But without success. I think it's some kind of program installation/configuration/profile that needs to be changed.
  
  My problem is to get the missing icon for Reqs OP too. Anyone has any info please help me. I don't know where to look. Any help is greatly appreciated.
  
  Thank you
  Kalyan.

  Hello

  The icon of the Document in the page Details of Notification Workflow is shown depending on whether the function of the form is assigned to the current user (selected responsibility). You can run $FND_TOP/sql/wfmlrdbg.sql to identify the specific function of the shape associated with the formula IN Req and see if your current context has access to this function of the form.

  In other words, you can check if you see the icon when you access the same notification of responsibility iProcurement.

  I hope this helps.
  Vijay

• Where can I find instructions for alternative configurations for my time capsule?

  I am resident in a House with a router not apple using Uverse.  I just bought a Time Capsule, hoping to use it as a storage drive to backup my imac and mac air.  For the MacAir, I would be like it is able with time Capsule wireless backup, and depending on how I can configure the system, connect the imac directly to the TimeCapsule or wireless connection.

  What I can't do connect the Capsule of time with an ethernet cable to the router not apple, that is in a different room than my desktop.  I have permission to use the internet service provided by the non-apple router - so right now, I don't have time Capsule to provide internet access in itself - as long as it can enable to backup wireless option at least for my mac air.

  Any suggestions?

  Unfortunately, you're stuck in the middle of a router that is not apple and an Apple router without ethernet... and therefore no way to connect.

  What you need is a wireless bridge (wireless to ethernet bridge if you want that it is more accurate).

  Wireless bridges are pretty cheap... Look at TP-Link, because a lot of their wireless access points will make wireless bridge...

  Or you can purchase an airport express... It's the only apple router which allows the wireless bridge. However, it is more than twice the price of an equivalent of non-apple.

  With the bridge... you plug in ethernet on the TC and run the TC in bridge (it is the router bridge)... your clients can then connect to the TC directly and the two backup and get internet at the same time... otherwise you can do it in the order...

  That is, you can plug the TC to the iMac by ethernet. It's a bit complicated, but I've given instructions here. Then you have wireless internet and backup on ethernet... It is indeed the best configuration for the imac.

  Time Capsule using wired for Mac for backup only.

  What you can't do, is use wireless for internet and backup at the same time... you will need to do one and then sometimes switch for the wireless of TC to run a backup... not a great idea.

• HP EliteDesk 800 G1 SFF: HP EliteDesk 800 G1 SFF: using VGA and DisplayPort simultaneously for double configuration monitor

  If the title says it all. I'm trying to set up two monitors on my HP EliteDesk 800 G1 SFF. Here is my configuration:

  1. first monitor (Acer B223W) lights DisplayPort and displays things normally.

  2. second monitor (HP LP2065) is on the VGA port.

  The problem is that my second port monitor never gets a signal from the machine and going to sleep mode. Connect the second monitor changes my main screen at a desk empty (no icons, no taskbar, just a plain painted paper), which I believe means it tries to use my VGA monitor as main display.

  However, the VGA monitor never seems to show anything. I spent my main screen on the first monitor successfully too, but is not all about him either.

  Dear customer,

  Welcome to the HP consumer's Support Forum!

  Please try and update the video driver following, chipset and BIOS:

  Intel Graphics Driver (64-bit) (International):

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=5387481&swItemId=vc_140415_1&swEnvOid=4059

  Intel Chipset drivers:

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=5387481&swItemId=vc_124826_1&swEnvOid=4059

  BIOS:

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=5387481&swItemId=vc_147068_1&swEnvOid=4058

  In case the problem persists, please exchange the monitor and VGA cables cables once and check.

  Try and clear CMOS by following the steps below:

  1. turn off the computer and unplug the power cord from the power outlet.
  2. remove the access panel.
  3. on the system board, hold down the CMOS button for 5 seconds.
  4. replace the chassis access panel and reconnect the power cord.
  5 turn on the computer and let it boot.

  Hope this helps, for other queries in response to the post and feel free to join us again.

  * Click on the star of CONGRATULATIONS on the left to say thank you *.

  Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.

  Thank you
  GR1
  Although I am an employee of HP, I speak for myself and not for HP

• HELP for re - configure RAID

  I have a windows 8/4th GEN Envy 17 jo29nr. What they do not mention in the description of the form, it's that it comes with a 25 GB SSD for caching. In addition, the standard drive is a disk of 1 TB 5400 RPM / min. I removed the RAID to install an SSD, but now, I want to just put a 750 GB drive at 7200 RPM and reconfigure the RAID for the use of the Intel memory smart caching. But when I go to set up a RAID 0 volume, it will only allow me to (approximately) 44GB, twice the size of the available mSATA SSD. There is literally no option that will change that. Any help would be appreciated big time.

  Heretikos,

  When configuring RAID 0 with 2 hard disks of different size it always diminishes the largest room of the same size as the smallest for interlacing.

  The smallest mSATA SSD in the system is to set up the Cache and no RAID 0 in the Intel rapid storage technology. It's original installation on your laptop.

  Let me know if your still following this thread I'd like to talk with you more about this.

• Microsoft is working on the lower graph Windows for low configure PC running on P4 processors?

  Original title: Microsoft Windows XP updates

  International news that I listen to Microsoft is Shutting Down Windows XP support! In my opinion, good decision but it is a problem here!

  Problem is that half of the poor Nations currently work on old systems of the world (Pentium 4) as demand for the latest Version of Microsoft Windows (Win 7 Vista) Pentium 4 is not reliable...

  Is that Microsoft is working on low graphics Windows for this Type of low PC configuration?

  Hello

  We have no information on this version of Windows. RT 8.1 8.1/windows platform is the most recent Microsoft and we will see the updated versions of these systems in the future.

  In my opinion, Intel Pentium 4 series of processors can run Windows 7 quite well, provided a sufficient amount of memory living and disk space are available. You can have a look at system requirements of Windows 7 for more information on this.

  Information on this link might be useful as well:

  http://www.Microsoft.com/en-us/Windows/enterprise/end-of-support.aspx

  Thank you and have a nice day!

• WCG200 & WRT54GS together for internet configuration problems

  OK I wil l provide as much information as I can here. First of all, the problem is that until the other day I've used DSL and now switched to comcast cable.  As such, I went and bought the wcg200 cable modem only to find out that there seems to be problem there with the firmware wireless.  Before buying the wcg200, I still have a wireles g Linksys WRT54GS.  Now, I just want to use the modem cable as an internet modem and continue to access everything I got via the 54gs wireless router and cannot find out how to configure the 54gs.

  Here is the TRICK so far.  When I restart my computer my default gateway is 192.168.1.1, which is the 54gs and I don't get any INTERNET CONNECTION.

  If I have enough IPCONFIG RENEW it switches to 192.168.1.2, and I get INTERNET & life is the way it has been.  Power down the pc and the re-boot and I'm back to 1.1.  Please don't tell me that I have create a .bat file to include in the boot to release and renew.  I'm sure it's a setting somewhere on the 54gs to have this work wireless, but use the wcg200 gateway.

  The cables are as follows:

  -patch cable cat5 wcg200 port 1 to port 1 on 54gs

  -wire cable from my computer to port 1 of 54gs until I can get this to work.

  -I can ping 192.168.1.1 which is 54gs & 192.168.1.2 = wcg200

  Currently on the wcg200:

  -DHCP is on

  -IP address is 192.168.1.2

  -IP from de.1.100 for 50

  -Wireless is disabled

  -Everything is disabled except for the firewall, multicast and porscans, these are the default values for security.

  -Everythign else is default

  -upnp disabled

  -firmware is 2.0.3.5.10 - 0425

  ON THE WRT54GS

  -J' deleted the PPPoe configuration.

  -IP address is 192.168.1.1

  -DHCP is also on (it can not be good)

  -wireless is on with - wep

  -block the anonymouse applications internet is on

  -multicast filter is on

  -filter idnet port 113 is on

  -upnp enabled

  THX

  Snowman777

  Option 1: You still use the WCG200 gateway router and the WRT as simple access point. You almost have it. All you have to do is to disable the DHCP server on the WRT. Only the WCG is the gateway router and the DHCP server on the WCG gives correct gateway IP address. The WRT connects customers with wireless local area network. Internet settings on the WRT-related (e.g. the type of internet connection, filter, blocking, upnp, transfer/port triggering, etc.) are not all relevant because these functions have meaning only if the internet connection is connected to the internet port of the WRT. You probably want to disable the wireless in the WCG radio, if you don't want to use it.

  Option 2: Transform the WCG in a modem, or disable routing all and NAT. disable the DHCP server on the WCG. Then, on the Administration - Advanced page there is the option to turn off 'Routing and NAT '. This disables the functions of routing and makes the WCG in a standard modem. So disable Routing & NAT. You will lose the connection to the WCG.

  Now, you reconfigure the WRT: you open the web interface http://192.168.1.2/ enable the DHCP server (or better leave it turned on). Set the type of internet connection on automatic/DHCP. If you wish you can put the WRT default 192.168.1.1 IP address. Save the settings. Now, cable wires of the WCG in the internet port of the WRT. The WRT must now use the WCG as modem and gets his audience to the internet IP address of your ISP. You can check on the status of the WRT page. Now it should show an IP address instead of the 0.0.0.0 that you see if you connect the WRT by port 1 for the WCG. Make sure that your computers renewal DHCP IP address either by restarting or by entering "ipconfig / renew *" as an administrator in a command prompt window.

  That's all.

  A note: according to the manual of the WCG will be internal IP address 192.168.100.1. If you need to make changes on the WCG once again, you must either set up a static IP address on a computer inside the 192.168.100. * with the subnet mask 255.255.255.0 and connect the computer directly to the WCG or you simply press the reset of the WCG for 30 seconds to reset. Then the WCG is back to 192.168.0.1 with active DHCP server, i.e. you can connect a computer directly to the WCG, it gets a valid IP address to connect to the WCG and you can make changes again.

• Best practices for the configuration of HTML5 and native connector at the same time.

  Is it possible to configure the HTML5 and native connector for my users? What would be the best configuration?

  The best way I found to do this is to create 2 web interface sites. one configured for native connector and one for HTML5. I put a URL in the message with a message center as "it is the site of native connector. Click on to HTML 5 ". A similar message with a URL to the site of native connector is on the site of HTML 5.

  Scott.

• LDAP AAA for VPN configuration

  Preface: I'm all new to Cisco Configuration and learn as I go.

  I'm at the stage of configuration LDAP to configure a VPN on ASA 5520, software release 8.3 (1).  Previously the programme installation and RADIUS authentication successfully tested, I tried to use similar logic to implement the LDAP authentication/authorization.  I have acquired a service account that queries the pub for the identification of the registered user information.  My main resource was the following Manual: Cisco ASA 5500 Series Configuration Guide using the CLI Software Version 8.3.  I did initially configurations by using ASDM, but could not get tests to succeed.  So I amazed the ASDM configs and went to the CLI.  Here is the configuration.

  AAA-server AAA_LDAP protocol ldap
  AAA-server host 10,20,30,40 (inside) AAA_LDAP
  Server-port 636
  LDAP-base-dn domain.ad
  LDAP-scope subtree
  LDAP-naming-attribute uid
  LDAP-login-password 8 *.
  LDAP-connection-dn cn = commonname, OU = ou01, or = ou02, dc = domain, dc = ad
  enable LDAP over ssl
  microsoft server type
  LDAP-attribute-map LDAP_ATTRIB

  ---

  type tunnel-group ASA_DEFAULT remote access
  attributes global-tunnel-group ASA_DEFAULT
  authorization-server-group AAA_LDAP

  ---

  LDAP attribute-map LDAP_ATTRIB
  name of the MemberOf IETF Radius-class card
  map-value MemberOf "VPN users' asa_default

  ---

  I tested all the naming-attribute ldap alternatives listed with the same results.

  When I test the authentication using this configuration, I get the following error: ERROR: authentication server does not: AAA Server has been deleted

  When I test authorization using this Setup, I get the same error (except for the word permission instead of authentication).

  I am at a total loss.  Any help would be appreciated.

  I would use ldp.exe to see if you can make sure that the sytnax of your ldap-connection-dn is just as you have in your config, it really helps just copy and paste.

  The problem I see is the following:

  [210] link as st_domadm
  [210] authentication Simple running to st_domadm to 10.20.30.30
  [210] simple authentication for st_domadm returned credenti invalid code (49) als
  [210] impossible to link the administrator returned code-(1) can't contact LDAP er

  I suppose your ldap-connection-dn is st_domadm and you try to test with the administrator account?

  Thank you

  Tarik

• Best practices for the configuration of virtual drive on NGC

  Hello

  I have two C210 M2 Server with 6G of LSI MegaRAID 9261-8i card with 10 each 135 GB HDDs. When I tried the automatic selection of the RAID configuration, the system has created a virtual disk with RAID 6. My concern is that the best practice is to configure the virtual drive? Is - RAID 1 and RAID5 or all in a single drive with RAID6? Any help will be appreciated.

  Thank you.

  Since you've decided to have the CPU on the server apps, voice applications have specified their recommendations here.

  http://docwiki.Cisco.com/wiki/Tested_Reference_Configurations_%28TRC%29

  I think that your server C210 specifications might be corresponding TRC #1, where you need to have

  RAID 1 - first two drives for VMware

  RAID 5 - 8 hard drives within the data store for virtual machines (CUCM and CUC)

  HTH

  Padma