ACL RA VPN
Hello
I have configured the Tunnel VPN RA, everything works fine, but now I want to allow only the http/www port because the vpn client should have access to my application server only, rest of the port should be blocked how to do this?
Your ACL 2 line is totally incorrect.
(1) HTTP is a protocol TCP, UDP, no
(2) you can't have a port source www - because it is in the range of ports restrcited, your source port will ALWAYS be 1024 to 65535.
Re - configure line: -.
permit for line of RA-tunnel access list lengthened 2 tcp 192.168.1.0 255.255.255.0 10.0.0.0 255.255.255.0 eq www
HTH >
Tags: Cisco Security
Similar Questions
-
Is it possible to do it on an ASA? I don't understand how a router can do a better job with control of asymmetric flow as an ASA.
168 VPN ipsec-isakmp crypto map
LongRidge-CareOne-CUST Site-to-Site Description
defined by peer 108.170.125.242
ip access-group VPNCryptoMap168_in-ACL set in
ip access-group VPNCryptoMap168_out-ACL set on
game of transformation-AES256_SHA
match address VPNCryptoMap168-ACLIP VPNCryptoMap168-ACL extended access list
Note CUST-CareOne-LongRidge VPN Site-to-Site
IP 10.61.0.0 allow 0.0.255.255 172.18.61.0 0.0.0.255
IP VPNCryptoMap168_in-ACL extended access list
Note CUST-CareOne-LongRidge VPN Site-to-Site
allow any object-group CareOne_Somerset_restrict-og-response to icmp echo
allow any host eq snmp 10.61.23.101 udp
allow any host 10.61.23.101 eq tftp udp
allow tcp any a Workbench
allow any host 10.61.202.88 eq www lpd 5357 5800 and 5900 tcp telnet
IP VPNCryptoMap168_out-ACL extended access list
Note CUST-CareOne-LongRidge VPN Site-to-Site
object-group CareOne_Somerset_restrict-og ip permit anyUnfortunately, the "vpn-filter option" under the group policy on the Cisco ASA applies only the VPN filter in the incoming direction and automatically configures the outbound direction. Refer to this link. There is an improvement that has been opened to support VPN filters in each direction, but it is not yet applied.
The only way I see is to modify the default behavior and configure ASA to submit VPN traffic to ACL interface using the command of not sysopt connection VPN-enabled and then configure ACL interface accordingly. I don't know if it's worth to you.
-
Download ACL for VPN users. ACS 4.1 &; 1841 router
Hello
I have configured the router 1841 as a VPN server. All VPN users get authenticated using RADIUS ACS 4.1
I need to apply downloadable ACLs by user.
I configured the Downlodabale ACL ACS. Same ACS event report shows that the ACL is applied to the authenticated user, but traffic is not blocked or past accordingly.
What is your configuration?
I think that the more easy to do is to use IPSEC TIV in interfaces, as well as the aaa authorization network and on the radius server, use ip:inacl to the cisco av pair, as
IP:inacl #1 = permit tcp any any eq 80
IP:inacl #2 = permit tcp any any eq 443
...
Some documents:
http://www.Cisco.com/en/us/docs/iOS/12_3t/12_3t14/feature/guide/gtIPSctm.html#wp1090634
-
We have a client that VPN in a Pix 515. I inserted the configuration of intra-interface same-security-traffic allowed on the pix so that members of staff who use the VPN would be able to access a specific resource from the public side. What I would do is to continue to use the same-security-traffic intra-interface command permit, but restrict access to other resources to the VPN client. Can I assign an access list to the VPN client allowing 10.10.10.10 everything and refuse all other connections? Where can I insert this in the VPN structure?
Thank you
Yes.
Kind regards
Arul
* Please note all useful messages *.
-
IOS router + VPN + ACS downloadable IP ACL
I want to use the function "Downloadable IP ACL" 3825-router VPN (OI 12.4 T) in combination with a CBS.
In many documents and discussions, I read that it is possible to use the DACLs on "devices Cisco IOS version 12.3 (8) T or higher.
Authentication and authorization by the AEC works and the device gets some settings of the av-pair-feature.
I have tried several things to apply the DACL as the use of av pairs or ACS "Downloadable IP ACL" function, but nothing works.
In the debug log, I see that the av pair is transmitted to the device, but it is not used.
--> Can you tell me, is it possible to use the DACLs on the IOS routers?
--> How does it work? What can I change?
--> Is there a good manual to apply it?
Thanks for your help!
Martin
It would be useful to know the PURPOSE of what you're trying to do...
AFAIR client config mode requires no ACL for filtering short tunnel split ACL... and I have no way to test right now.
If you want to allow or not some clients access to certain subnets why not investigate tunneling ACL and vpn-filter in combination with ACS split will rather than for the DACL.
-
ACL entering for public router VPN
Hi all
I set up our VPN router for access to all of our mobile customers. Our private VPN range is going to be 172.16.10.x/24. I have to add ACL allow rules for this range on our ACL entering all inside LANs to facilitate access for VPN users?
for example int S0/0/0
IP address 85.x.x.x
IP access-group 100 to
access-list 100 permit ip 172.16.10.0 0.0.0.255 192.168.1.0 0.0.0.255
If I understand it, once the user connects the VPN tunnel to the inside of the interface, so is traffic through the VPN is encapsulated and therefore wouldn't appear as a private IP address?
All comments are greatly appreciated.
Paul
Sorry I mean you should not change outside the acl for vpn traffic for the rest of the things you can do.
Thank you
Ajay
-
Cisco ASA, connect an IP address on the OUTSIDE of the VPN remote access
Hello
I tried to find resources on the net but could not find a solution, then post it here. Maybe someone can help.
So the problem is that I'm trying to access a server on the cloud for remote VPN access (cisco asa 5510).
The server on the cloud (54.54.54.54) is only accessible from the outside interface (192.168.11.2) NY Firewall (cisco asa 5510)
I added some ACE for this in the ACL of VPN tunnel to divide.
NY-standard host allowed fw # access - list vpn_remote-customer 54.54.54.54
And I see the road added to my cliet machine after the VPN connection, but still it cannot connect to this server.
The network INTERIOR, I can connect to the server.
Thanks in advance.
Hello
This is most likely a problem with NAT hair/U-turn hairpin.
Will need to see the configurations or you would need to check yourself
I don't know what your version of the Software ASA is to be like who determines what is the format of NAT configuration.
So far, you have confirmed that the ASA VPN configuration provides the VPN Client with the route to the remote server. Then in circulation should be tunnel to the ASA.
Then, you will need to check the output of this command
See the race same-security-traffic
You should see the command in the output below
permit same-security-traffic intra-interface
If you do not, you will need to add it. This effect of controls is to allow traffic to enter an interface and exit through the same interface. In your case this applies to Internet VPN Client traffic to the remote server as it between ' outside ' and spell through the 'outside'.
Then, should ensure that dynamic PAT is configured for the VPN Clients.
8.2 software (and below)
You most likely have a dynamic configuration PAT like that on the firewall, if levels of above running software version
Global 1 interface (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0
In this situation if we wanted to add dynamic PAT for a pool of VPN, we would add
NAT (outside) 1
This would allow users to use the same public IP address as LAN users, when accessing the remote VPN server
Software 8.3 (and above)
Because the NAT configuration format is completely different in the latest software, you could probably just add a new configuration of NAT completely without adding a
network of the VPN-PAT object
subnet
dynamic NAT interface (outdoors, outdoor)
Of course, its possible that there could be some configuration NAT already on the device which could cause problems for this configuration. If this does not work then that we would have to look at the actual configurations on the ASA.
Hope this helps
Let me know how it goes
-Jouni
-
ASA Anyconnect VPN do not work or download the VPN client
I have a Cisco ASA 5505 that I try to configure anyconnect VPN and thought, I've changed my setup several times but trying to access my static public IP address of the external IP address to download the image, I am not able to. Also when I do a package tracer I see he has been ignored through the acl when the packets from side to the ASA via port 443, it drops because of the ACL. My DMZ so will he look like something trying to access the ASA via the VPN's going to port 443. Here is my config
XXXX # sh run
: Saved
:
ASA Version 8.4 (3)
!
hostname XXXX
search for domain name
activate pFTzVNrKdD9x5rhT encrypted password
zPBAmb8krxlXh.CH encrypted passwd
names of
!
interface Ethernet0/0
Outside-interface description
switchport access vlan 20
!
interface Ethernet0/1
Uplink DMZ description
switchport access vlan 30
!
interface Ethernet0/2
switchport access vlan 10
!
interface Ethernet0/3
switchport access vlan 10
!
interface Ethernet0/4
Ganymede + ID description
switchport access vlan 10
switchport monitor Ethernet0/0
!
interface Ethernet0/5
switchport access vlan 10
!
interface Ethernet0/6
switchport access vlan 10
!
interface Ethernet0/7
Description Wireless_AP_Loft
switchport access vlan 10
!
interface Vlan10
nameif inside
security-level 100
IP 192.168.10.1 255.255.255.0
!
interface Vlan20
nameif outside
security-level 0
IP address x.x.x.249 255.255.255.248
!
Vlan30 interface
no interface before Vlan10
nameif dmz
security-level 50
IP 172.16.30.1 255.255.255.0
!
boot system Disk0: / asa843 - k8.bin
passive FTP mode
DNS lookup field inside
DNS domain-lookup outside
DNS domain-lookup dmz
DNS server-group DefaultDNS
Name-Server 8.8.8.8
Server name 8.8.4.4
search for domain name
network obj_any1 object
subnet 0.0.0.0 0.0.0.0
network of the Webserver_DMZ object
Home 172.16.30.8
network of the Mailserver_DMZ object
Home 172.16.30.7
the object DMZ network
172.16.30.0 subnet 255.255.255.0
network of the FTPserver_DMZ object
Home 172.16.30.9
network of the Public-IP-subnet object
subnet x.x.x.248 255.255.255.248
network of the FTPserver object
Home 172.16.30.8
network of the object inside
192.168.10.0 subnet 255.255.255.0
network of the VPN_SSL object
10.101.4.0 subnet 255.255.255.0
outside_in list extended access permit tcp any newspaper object Mailserver_DMZ eq www
outside_in list extended access permit tcp any newspaper EQ 587 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper SMTP object Mailserver_DMZ eq
outside_in list extended access permit tcp any newspaper of the Mailserver_DMZ eq pop3 object
outside_in list extended access permit tcp any newspaper EQ 2525 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper of the Mailserver_DMZ eq imap4 object
outside_in list extended access permit tcp any newspaper EQ 465 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper EQ 993 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper EQ 995 object Mailserver_DMZ
outside_in list extended access permit tcp any newspaper EQ 5901 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper Mailserver_DMZ eq https object
Note access list ACL for VPN Tunnel from Split vpn_SplitTunnel
vpn_SplitTunnel list standard access allowed 192.168.10.0 255.255.255.0
pager lines 24
Enable logging
timestamp of the record
exploitation forest-size of the buffer to 8192
logging trap warnings
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
MTU 1500 dmz
local pool VPN_SSL 10.101.4.1 - 10.101.4.4 255.255.255.0 IP mask
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 647.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) static source inside inside static destination VPN_SSL VPN_SSL
NAT (exterior, Interior) static source VPN_SSL VPN_SSL
!
network obj_any1 object
NAT static interface (indoor, outdoor)
network of the Webserver_DMZ object
NAT (dmz, outside) static x.x.x.250
network of the Mailserver_DMZ object
NAT (dmz, outside) static x.x.x.. 251
the object DMZ network
NAT (dmz, outside) static interface
Access-group outside_in in external interface
Route outside 0.0.0.0 0.0.0.0 x.x.x.254 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
AAA-server protocol Ganymede HNIC +.
AAA-server host 192.168.10.2 HNIC (inside)
Timeout 60
key *.
identity of the user by default-domain LOCAL
Console HTTP authentication AAA HNIC
AAA console HNIC ssh authentication
Console AAA authentication telnet HNIC
AAA authentication secure-http-client
http 192.168.10.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ca trustpoint localtrust
registration auto
Configure CRL
Crypto ca trustpoint VPN_Articulate2day
registration auto
name of the object CN = vpn.articulate2day.com
sslvpnkey key pair
Configure CRL
Telnet 192.168.10.0 255.255.255.0 inside
Telnet timeout 30
SSH 192.168.10.0 255.255.255.0 inside
SSH timeout 15
SSH version 2
Console timeout 0
No vpn-addr-assign aaaDHCP-client update dns
dhcpd dns 8.8.8.8 8.8.4.4
dhcpd outside auto_config
!
dhcpd address 192.168.10.100 - 192.168.10.150 inside
dhcpd allow inside
!
dhcpd address dmz 172.16.30.20 - 172.16.30.23
dhcpd enable dmz
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
authenticate the NTP
NTP server 192.168.10.2
WebVPN
allow outside
AnyConnect image disk0:/anyconnect-linux-64-3.1.06079-k9.pkg 1
AnyConnect enable
tunnel-group-list activate
internal VPN_SSL group policy
VPN_SSL group policy attributes
value of server DNS 8.8.8.8
client ssl-VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list vpn_SplitTunnel
the address value VPN_SSL pools
WebVPN
activate AnyConnect ssl dtls
AnyConnect Dungeon-Installer installed
AnyConnect ssl keepalive 15
AnyConnect ssl deflate compression
AnyConnect ask enable
ronmitch50 spn1SehCw8TvCzu7 encrypted password username
username ronmitch50 attributes
type of remote access service
type tunnel-group VPN_SSL_Clients remote access
attributes global-tunnel-group VPN_SSL_Clients
address VPN_SSL pool
Group Policy - by default-VPN_SSL
tunnel-group VPN_SSL_Clients webvpn-attributes
enable VPNSSL_GNS3 group-alias
type tunnel-group VPN_SSL remote access
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect esmtp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:d41d8cd98f00b204e9800998ecf8427e
: endXXXX #.
You do not have this configuration:
object network DMZ nat (dmz,outside) static interface
Try and take (or delete):
object network DMZ nat (dmz,outside) dynamic interface
-
9.0 can a dynamic nat be used via ipsec vpn?
9.0 can a dynamic nat be used via ipsec vpn?
We have a vpn and work between asa and when we run traffic through a static nat rule traffic goes over the vpn. When we use a dynamic nat traffic does not get picked up by the ACL vpn.
We disable the nat rules to switch back and just so, even when we use the same destination to source the result is the same.
Am I missing something with 9.0 versions of code? If I disable all the nats and pass traffic it goes via the vpn.
So, it seems that when you use the dynamic nat statement, it pushes traffic to the external interface without looking at the acl of vpn. Please let me know if I'm crazy, I'm a newb on 8.3 zip code.
Thank you
Have you included in the ACL crytop natted ip address or range?
You allowed natted ip address or range to the other end of the tunnel?
-
Hello
I've set up IPSec VPN remotely and it works fine. I need access to connected VPN clients, and it does not work. I have already added an entry to traffic allowing sheep ACL from inside my network to the VPN.
More information:
Inside of the net: 10.1.1.0/24
Pool VPN: 172.30.1.0/24
Is it possible to access from my internal network to the VPN users?
Thanks in advance.
Best regards.
Marcelo
VPN users have access to certain servers via the list of Tunnel from Split.
Marcelo,
Split tunnel ACLs must be an IP acl, it is not recommended and supported to set the TCP ports on the split tunnel ACL, the vpn client don't interpret this ACl as a lot are interested in IP, TCP ports, and that could cause you a problem. You can change your config to reflect this. Regarding ACL split tunnel, it must contain the server line. networks that this vpn, customers arrive, remind you this is two-way, as you know.
So if IT supports the IP range is on this vpnExample ACL vpn clients will be able to reach the IT support guys and vice versa.
I advise you to change your split tunnel ACLs to specific ports to only the desired servers and the presenters what these customers need to achieve.
Remove the ports out of this Split tunnel ACLs.
If you need to restrict services for vpn rather clients use VPN filters.
-
8.2 ASA vpn filter for connections l2l
I have a vpn-filter set to my police L2L. The remote site uses a Cisco 1811 router and the main hub is a Cisco 5580. I already have an acl of vpn-filter in place on an existing L2L connection which works fine. The only question is, when I make changes to the ACLs for add/remove access, I have to reload the whole of the tunnel until the changes take place.
My question is, are at - it a command to reload the access control without destroying the tunnel?
Hi Jeffrey,.
Design whenever there are changes in the attributes of Group Policy (including the vpn-filter, dns ip of victories or vpn-Protocol etc.), you need to reset the respective tunnel while phase 2 is negotiating with the newly added policy. The command to clear a specific tunnel is: -.
his clear crypto ipsec peer
For more details on the command, please see the link below
http://www.Cisco.com/en/us/docs/security/ASA/asa80/command/reference/C3.html#wp2133652
So, to answer your query wasn't there command is not to reset the access control. There had been such a command you would still back the tunnel to trigger negotiations ipsec with the new group policy settings.
HTH...
Concerning
Mohit -
Hello
I have a headquarters and a remote site and I want to get a VPN site-to site between the two. I have the following Setup on each router. 'Show encryption session' says that the VPN is in the IDLE-UP condition (and my somewhat limited understanding of virtual private networks, this means that the phase 1 of IKE is complete and waiting for phase 2) When you run a "debug crypto ipsec" on the remote site, I get "no ip crypto card is for addresses local 100.x.x.x" and the VPN remains to IDLE-UP. The ACL on the external interface allows the IP of the remote site. I have CBAC running on the external interface of both routers and ACL permits all traffic between the addresses 100.x.x.x and 200.x.x.x. Could someone help me with the config? I have to do something wrong somewhere.
Thank you!
Shaun
Router HQ: Local 10.2.0.0/16 (network)
crypto ISAKMP policy 1
BA aes 256
md5 hash
preshared authentication
Group 5
ISAKMP crypto keyaddress 100.x.x.x
!
86400 seconds, duration of life crypto ipsec security association
!
Crypto ipsec transform-set aes - esp AES_MD5_COMPRESSION esp-md5-hmac comp-lzs
!
card crypto S2S_VPN local-address FastEthernet0/0
!
S2S_VPN 10 ipsec-isakmp crypto map
the value of 100.x.x.x peer
game of transformation-AES_MD5_COMPRESSION
PFS Set group5
match address TRAFFIC_TO_REMOTE_NETWORK
!
interface FastEthernet0/0
IP address 200.x.x.x 255.255.255.252
IP access-group firewall in
NAT outside IP
no ip virtual-reassembly
card crypto S2S_VPN
!
TRAFFIC_TO_REMOTE_NETWORK extended IP access list
IP enable any 10.1.0.0 0.0.255.255Remote router: (LAN 10.1.0.0/16)
crypto ISAKMP policy 1
BA aes 256
md5 hash
preshared authentication
Group 5
ISAKMP crypto keyaddress 200.x.x.x
!
86400 seconds, duration of life crypto ipsec security association
!
Crypto ipsec transform-set aes - esp AES_MD5_COMPRESSION esp-md5-hmac comp-lzs
!
card crypto S2S_VPN local-address FastEthernet0/0
!
S2S_VPN 10 ipsec-isakmp crypto map
the value of 200.x.x.x peer
game of transformation-AES_MD5_COMPRESSION
PFS Set group5
match address TRAFFIC_TO_HQ_NETWORK
!
interface FastEthernet0/0
IP address 100.x.x.x 255.255.255.252
IP access-group firewall in
NAT outside IP
no ip virtual-reassembly
card crypto S2S_VPN
!
TRAFFIC_TO_HQ_NETWORK extended IP access list
IP 10.1.0.0 allow 0.0.255.255 10.2.0.0 0.0.255.255Hi Shaun,
Some comments...
The QM_IDLE means that the phase 1 is established. (sh cry isa his)
You should see with "sh cry ips its" that he has put SAs in place for IPsec encryption/decryption of traffic for the phase 2.
The ACL for VPN (the crypto ACL) should be one mirror of the other (you have "all" on one side and two statements by the other peer network.
You do NAT, therefore, there should be a 'workaround NAT rule' VPN traffic (to remove the IPsec NAT traffic).
This should be it.
Federico.
-
Summary:
We strive to establish a two-way VPN L2L tunnel with a partner. VPN traffic is one-to-many towards our partner, and our partner they need of a many-to-one to us (they need to access a host on our network). In addition, our partner has many VPN, so they force us to use a separate NAT with two private hosts addresses, one for each direction of the tunnel.
My initial configuration of the tunnel on my grown up side of Phase 1, but not IPSec. Partner ran debug that revealed that my host did not address NAT'd in the NAT policy. We use an ASA5520, ver 7.0.
Here is the config:
# #List of OUR guests
the OURHosts object-group network
network-host 192.168.x.y object
# Hosts PARTNER #List
the PARTNERHosts object-group network
network-host 10.2.a.b object
###ACL for NAT
# Many - to - many outgoing
access-list extended NAT2 allowed ip object-group OURHosts-group of objects PARTNERHosts
# One - to - many incoming
VIH3 list extended access permit ip host 192.168.c.d PARTNERHosts object-group
# #NAT
NAT (INSIDE) 2-list of access NAT2
NAT (OUTSIDE) 2 172.20.n.0
NAT (INSIDE) 3 access-list VIH3
NAT (OUTSIDE) 3 172.20.n.1
# #ACL for VPN
access list permits extended VPN ip object-group objects PARTNERHosts OURHosts-group
access allowed extended VPN ip host 192.168.c.d PARTNERHosts object-group list
# #Tunnel
tunnel-group
type ipsec-l2l card
<#>crypto is the VPN address card crypto
<#>the value transform-set VPN #>card
<#>crypto defined peer #> #>I realize that the ACL for the VPN should read:
access allowed extended VPN ip host 172.20.n.0 PARTNERHosts object-group list
access allowed extended VPN ip host 172.20.n.1 PARTNERHosts object-group list
.. . If the NAT was working properly, but when this ACL is used, Phase 1 is not even negotiating, so I know the NAT is never translated.
What am I missing to NAT guests for 172.20 addresses host trying to access their internal addresses via the VPN?
Thanks in advance.
Patrick
Here is the order of operations for NAT on the firewall:
1 nat 0-list of access (free from nat)
2. match the existing xlates
3. match the static controls
a. static NAT with no access list
b. static PAT with no access list
4. match orders nat
a. nat [id] access-list (first match)
b. nat [id] [address] [mask] (best match)
i. If the ID is 0, create an xlate identity
II. use global pool for dynamic NAT
III. use global dynamic pool for PAT
If you can try
(1) a static NAT with an access list that will have priority on instruction of dynamic NAT
(2) as you can see on 4A it uses first match with NAT and access list so theoretically Exchange autour should do the trick.
I don't see any negative consequences? -Well Yes, you could lose all connectivity. I don't think that will happen, but I can't promise if you do absolutely not this after-hours.
Jon
-
Disable XAuth for remote access VPN
Hi guys,.
I would like to know if I can jump XAuth for access to remote VPN on a router.
Here's my config, all working beautifully, always on connection I do not see any window username & password after having clicked on the Vpn profile.
local VPNUSERSAUTH AAA authentication loginlocal AAA VPNUSERS authorization networkra-user privilege 0 1cannotTELu secret user namecrypto ISAKMP policy 7BA aessha hashpreshared authenticationGroup 2Configuration group customer crypto isakmp VPNUSERStheKEYallneedt0 keyVPN-poolACL ACL-SPLIT-VPNCrypto ipsec transform-set esp-3des esp-sha-hmac 3DES-SHAcrypto dynamic-map VPNDYNMAP 1game of transformation-ESP-AES128-SHAmarket arriere-routelist of authentication of card crypto map-OUTSIDE client VPNUSERSAUTHlist of crypto card authorization card-OUTSIDE isakmp VPNUSERSclient configuration address card crypto map-OUTSIDE meetcard crypto 6500 map-OUTSIDE-isakmp ipsec dynamic VPNDYNMAPlocal IP VPN-POOL 10.1.24.1 pool 10.1.24.25IP extended ACL-SPLIT-VPN access listip licensing 192.168.11.0 0.0.0.255 10.1.24.0 0.0.0.255Thank you very much!Hi Florin,
In the case of remote VPN access, the user must be authenticated by name of user and password or certificates.
You can deploy authentication certificate based as follows: -.
http://www.Cisco.com/c/en/us/support/docs/security-VPN/IPSec-negotiation-IKE-protocols/22520-unityclient-iOS.html#router-configThis will use the certificate for authentication of users and only requires name of user and password.
Kind regards
Dinesh MoudgilPS Please rate helpful messages.
-
Doubt on the RA aaa using ACS 5.3 vpn user
Hello
I'm putting in place of the VPN on 8.4 ASA with 2 - VPNGp1 and VPNGp2. VPNGp1 groups users will access 1.2.3.0/24 and VPNGp2 users will have access to 5.6.7.0/24. User authentication will be done using RADIUS 5.3 ACS.
On ASA, I configured pools VPN groups, ACL of VPN, IP, tunnel of groups and group for each group strategies.
GBA, I created vpn-user1 and user2-vpn for each of the 2 groups.
I don't know if some configurations more must be done on ASA and AC... Do I need to add new users - vpn-user1 and user2-vpn - on ASA, under each corresponding group policy, using the command political vpn-group? Or I need to do something else on the ACS?
Finally, how can I configure authorization and accounting for VPN users? I have to do this on GBA or ASA?
Please advice.
Thank you.
Hello
Authentication using radius aims to centralize user accounts and policies so that you will not have to configure these on the SAA. You must create a group of authentication servers that points to your ACS, then you will have to refer to this group of servers to your tunnel-group for user authentication queries will be forwarded to ACS for authentication. For accounting you will create an accounting server group and also assign to your tunnel group configuration.
The GBA, you will need to create a network client that is ASA, and the shared secret will be the same. You create an element of authorization policy network who have the permission settings, or you can choose allowed access, which allows authentication succeed without any special authorization.
You can debug the sessoin using crypto vpnclient 255 debugging to view the authentication stream.
Using SSL vpn (anyconnect) for these sessions?
Thank you
Tarik Admani
Maybe you are looking for
-
iOS 10 gradation homescreen wallpaper
After upgrading my iPhone to iOS 10, I noticed the gradation of the wallpaper in the home screen. Please refer to the pictures attached - it is clearly visible that the homescreen wallpaper is darker that lock screen wallpaper notwithstanding, it's t
-
How to remove and old e-mail address of my Apple ID?
How to remove an old email address of my Apple ID?
-
USB port does not detect the USB storage
Hello My company gave me a Lenovo ThinkPad L420 and whenever I connect the USB external storage, I am not able to see it on my computer but I can see the unit on Control Panel devices and printers. Please let me know how activate or activate? Thank y
-
Dimension 4700 desktop will not start
I have a Dimension 4700 desktop computer that has been sitting in storage for a while. I wanted to start and see is there something to this subject that I had to save or erase the hard drive. As far as I know, it was working fine when it was put away
-
Network discovery cannot be activated, windows 7 Home premium.
This problem is very simple to describe, but I do have a lot of time I can't find a solution. Help appreciated. In the network and sharing Center, advanced screen sharing, there is the option to turn on network discovery and file/printer sharing. Whe