ACS4.0 device setup server GANYMEDE +.

Similar Questions

• Network troubleshooting is he diagnosed "your computer is correctly configured, but the device dns server is not responding...". How can I fix it

  I get a lot offline on my laptop. After that I ran the network troubleshooting is diagnosed "your computer is set up correctly, but the device dns server does not respond.  How can I fix this problem please?

  Hello

  1. what operating system is installed on your computer?

  2. are you using wired or Wi - Fi?

  3. you will remember to do recent changes on the computer before this problem?

  I suggest you

  Method 1:

  Empty the Cache DNS (Domain Name System) follow the steps below:

  a. click the Start button.

  (b) in the search box, type command prompt.

  c. in the list of results, right-click command prompt, and then click Run as administrator.  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  d. at the command prompt, type ipconfig/flushdns.

  Method 2:

  If the previous step fails, follow these steps and check if the problem persists:

  a. click "Start", enter "NCPA. CPL"(without the quotes) and press ENTER.

  b. right-click on the connection you use for the local connection, and then click "Properties".

  c. Click to select 'Protocol Internet Version 4 (TCP/IPv4)' and then click 'properties '.

  d. in the Internet Protocol window, we will change the "Preferred DNS server" to 208.67.222.222

  e. click 'OK' twice to complete the change.

  f. If the problem persists, please repeat the steps and change the "Preferred DNS server" to 208.67.220.220.

  Method 3:

  If the previous step fails, follow the steps described in the following link:

  http://support.Microsoft.com/kb/928152

  For more information, check the following links:

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

• Photosmart 8450: "Device Setup doesn't have all the.

  HP dear Forum and Support:

  My HP Photosmart 8450 fails to install on my Dell laptop. Help, please.

  I have a Dell Inspiron 640 m laptop computer with Windows XP. I got the printer installed fine, but then I caught a bad virus had to restore my laptop back to the factory settings and then installed Norton Antivirus.

  First, I downloaded the Driver on the HP site and connected the driver software Installation the file downloaded.

  Then, during Installation, the Installation Wizard told me to connect my printer to the USB Port of my computer, I did.

  Then, after a few minutes, the installation wizard told me that "Device Setup has not finished.'

  Then I tried whole, this time connect my device to a different USB Port in my laptop with the same failed result. In addition, no a HP printer icon appears in the list of printers in my control panel.

  A cause as possible, I can imagine would be if I have Norton Antivirus and Antivirus is blocked somehow, but I highly doubt this possibility, because then it would be a common problem with many users, like HP and Norton products are very common.

  Rakovsky

  P.S. happy holidays.

  OK, I gave you a thumbs up.

  Here's what worked for me:

  I uninstalled the printer from the "Programs" section in my control panel. Then I reinstalled the printer driver. When I did, I have connected my USB pritner when the installation wizard asked. As was happening, he said that the printer has been detected and this may take a few minutes.

  Meanwhile, a message apparently not HP-software popped up because of my operating system, that says hardware is automatically detected by my computer laptop and installed automatically and give me the choice to make my default printer. Of course, rather than interfere with the HP Installation Wizard, I've just left him intact.

  A few minutes later, I got the same old "Not completed" message in my installation wizard. Then I clicked on the operating system pop-up message and told to do my Pritner by default.

  I think that the installation wizard might at this time asked to click Next in the installation wizard, and if that were the case, then I didn't click it. But in any case the next thing the wizard said was that the device had been installed successfully.

  So it's a combination of things that led to the unit being installed successfully.

• connect with us. Choose a network and go online to complete the device setup

  My laptop installed new updates of windows the other day.  I tried to use my laptop for the first time since updates, and he says, ' Let's get connected. " Choose a network and go online to complete the device setup. "I went to Starbucks, because I have no internet, and he tried but would not connect at all.  I don't know what to do.  I can't use my computer now.  I just need to find another source of internet to try?  (I tried a few other random public networks that did not work and would not connect as well).

  Original title: update problem

  Hello

  Please contact Microsoft Community.

  I understand that you can not choose a network.

  I will definitely help you with this.

  You use a WIFI or Ethernet connection?

  I suggest you go through the steps below:

  Steps: Try to login or to create the new configuration of the connection:

  • Press the window key + R.

  • Type ncpa.cpl and press ENTER.

  • Right-click on the network connection, and then select Enable.

  • If this does not work, then try to new network configuration.

  • Right-click on the network icon in the lower right.

  • Click to open network and sharing Center.

  • Click setup, a new connection or network.

  I hope this helps. Please post back with the State of the question and we will be happy to help you further.

• Synchronization with single device synchronization server

  Hello

  This must be a FAQ, but I'm not, so this is. How can I sync data from the server for synchronization to Mozilla to one device?

  The context is that I am currently running Ubuntu Linux USB on my computer at home, because the boot on this computer record has been corrupted, so I can't access Windows. I would like to download the synchronization (Favorites, passwords) data from the server to the copy of Linux in Firefox 25. However, all the help I can see refers to coupling devices. I see that I can create a recovery key if I don't have the camera with me, but there is a terrible warning in the dialogue of FF Sync key reset will erase all data synchronization. I don't have access to another machine to pair, as I work at home. I looked at the page 'How to manage my Firefox Sync account' (https://support.mozilla.org/en-US/kb/how-do-i-manage-my-firefox-sync-account) and have tried to follow the instructions, but again, I come to a dialogue with the terrible warning, and really, I don't want to lose all my data synchronization on the server.

  So, is it possible to sync between a computer and the synchronization server?

  Fred
  www.fredriley.org.UK

  Hello fred, you can connect only one device to your existing account synchronization when you have the username, password & the available existing recovery key - you can do so in Preferences > sync > set up sync > I have an account > I don't have the camera with me. so you would need to know the current recovery - don't reset as it will remove all current data on the server as noted in the warning messages.

  Another way to import your old data would be if you still have access to the file system of your windows machine. then you could import some files from your old profile windows in your current profile folder in order to restore some data like bookmarks, paswords, history, etc.: recovery of data from an old profile

• Management of the client via GPO USB devices on Server 2003

  I copied the code available in http://support.microsoft.com/default.aspx?scid=kb;en-us;555324 and facilities an .adm file. added the template to the GPO administrative model. Me has "Restrict the player" under "Custom policy setting" under administrative templates. However, could not find anything on the right pane of the GPO while selecting "restrict drives". Pls tell me what needs to be done to make me the options to disable the USB devices on all customers of my company

  Hi Lenka,

  The question you posted would be better suited in the TechNet Forums.

  I would recommend posting your query in the link below.

  Windows Server forums:

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

• On the device HTTP Server

  Anyone know if it is possible to run an HTTP server on a BlackBerry?

  I want just a light super server to run on it. I found the ServerSocketConnection and this could work, the only thing is that I need to understand somehow what is the IP address of the device.

  I would do it on 4.6 / 4.7

  Thank you!

  Not possible sorry, the BlackBerry does not support TCP communications within the unit.

• BlackBerry Smartphones remove our mail from the device or server or the two lost when option OS upgraded

  I upgraded my OS 9360 recently of OS 7.0 to v 7.1.0.336, 9.6.0.51 platform. Since the upgrade I have more the possibility to delete email messages on handheld only or on the server as well. I really enjoyed having the option to delete totally or just on my handheld and then discovered the mail later on my pc.

  When I delete a mail from my BB, now, it just removes it from my device and the leash on the server without the option to remove it so. Can you please help me get this option back?

  Kind regards
  Stefan.

  Hello and welcome to the community!

  Please see, on your BB, here:

  • Home screen > Messages > > Options > email reconciliation

  On this screen should be the ability to set the preference to "remove the ' back to 'ask '.

  Good luck!

• MBSA hangs on some devices on Server 2003

  Try to run MBSA on some of our Server 2003 boxes and he is suspended during the process. I have a very small piece of green on the process bar, with the message below that says "Done to download security information". And an hourglass will run as long as I left it. The system and application logs show nothing. I try to use it to debug a problem with KACE, but cannot cross a race to see what he finds.  The system is Server 2003 R2 SP2. MBSA logs get generated, and if so, their place of residence. Any help would be appreciated.

  This issue is beyond the scope of this site and must be placed on Technet or MSDN

  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• Device Setup - switches and arrays

  I'm trying to configure vFoglight Storage for the first time. I have managed to add the VCs, but cannot configure switches or arrays.
  1 cisco switch receives an error during validation.
  Error 1: Connection Refused: the host refused connection socket on the specified port: usually indicates one of the following values: bad port specified by the user, the application that is supposed to be listening on port isn't listening, port is disabled (e.g. a firewall).
  I am specifying port 23. I can telnet to the switch from the same server using the credentials provided.
  2 Clariion CX4-480 receives an error during validation.
  error: "connection failed: connection to the host on the specified port is not taken.
  NaviSecCLI is installed and I am able to run the following from a command prompt C:\>NaviSECCli.exe- of the username-password - scope 0-address get config
  Thank you.

  I would like to see if we can contact the Clariion with the CLI on the server of Navi Manager.
  In Navi Manager, please try running this command prompt:
  NaviSECCli.exe - of the username-password - scope 0-address methods
  The username and password must be an account with global permissions.
  The Ip address is the IP address of your Clariion system.

• Microsoft DHCP - Option 43 Setup Server

  I have the scope properly configured insofar as the 241 Option with Option 43 and the VCI in for both the series 1130 and 1200 AP however, how can you do this job if your subnet has 1200 and 1130's inside? Basically if I have two 241 options set, the 1130 comes by first allowing the 1130 s associated, but not the 1200. If I remove the Option 241, the associated 1200 1130. Basically, how can I get both working properly the scope?

  Thank you

  Raun

  Hi Pierre Roussy.

  Here is some additional info;

  This section contains an example configuration DHCP Option 43 on a Windows 2003 Enterprise DHCP server for use with the lightweight access points. For other implementations of DHCP server, see DHCP Server documentation to configure DHCP Option 43. In 43 of the Option, you must use the IP address of the management interface of the controller.

  --------------------------------------------------------------------------------

  Note that DHCP Option 43 is limited to a single access point type by DHCP pool. You must configure a separate DHCP pool for each access point type.* *.

  This doc.

  http://www.Cisco.com/en/us/docs/wireless/access_point/1200/installation/guide/120h_g.html

  The DHCP OPTION 43 to light Cisco Aironet Access Points Configuration example

  http://www.Cisco.com/en/us/Tech/tk722/tk809/technologies_configuration_example09186a00808714fe.shtml#T1

  I hope this helps!

  Rob

• Notification between devices with server

  Hello

  I would like to know what is the best plugin/way to send notifications to another phone using my application?

  For example, send a message to a friend and that friend a notification with "you have received a message of...» »

  Thank you.

  You can start with the docs for this plugin:

  PhoneGap-plugin-push

• How the device select radius-server

  Hi guys,.

  We have the existing Ganymede configuration to form our devices and server ACS 2 did. the acs server are managed with other suppliers that the acs server is on their site. Now intended to manage the acs server. We installed a new server CSA of our location, we have thousand of the devices, if we move to the new server we just add the acs unit 2 Server? the new acs server will be are able to connect to the device? How a device chooses which acs primary or secondary server?  Please notify.

  Old configuration

  AAA new-model

  AAA authentication login vtymethod group Ganymede + local

  AAA authorization config-commands

  AAA authorization exec default group Ganymede + local authenticated by FIS

  AAA authorization commands 0 default group Ganymede + local authenticated by FIS

  15 AAA authorization commands default group Ganymede + local authenticated by FIS

  AAA accounting send stop-record an authentication failure

  AAA accounting exec default start-stop Ganymede group.

  orders accounting AAA 0 arrhythmic default group Ganymede +.

  orders accounting AAA 15 by default start-stop Ganymede group.

  Default connection accounting AAA power Ganymede group.

  AAA accounting system default start-stop Ganymede group.

  Ganymede IP source-interface Loopback0

  RADIUS-server host 10.x.x.x

  RADIUS-server host 10.x.x.x

  New config

  AAA new-model

  AAA authentication login vtymethod group Ganymede + local

  AAA authorization config-commands

  AAA authorization exec default group Ganymede + local authenticated by FIS

  AAA authorization commands 0 default group Ganymede + local authenticated by FIS

  15 AAA authorization commands default group Ganymede + local authenticated by FIS

  AAA accounting send stop-record an authentication failure

  AAA accounting exec default start-stop Ganymede group.

  orders accounting AAA 0 arrhythmic default group Ganymede +.

  orders accounting AAA 15 by default start-stop Ganymede group.

  Default connection accounting AAA power Ganymede group.

  AAA accounting system default start-stop Ganymede group.

  Ganymede IP source-interface Loopback0

  RADIUS-server host 10.x.x.x

  RADIUS-server host 10.x.x.x

  RADIUS-server host 100.x.x.x<-->

  RADIUS-server host 100.x.x.x<-->

  Hi m.,.

  N ° not round robin.

  It checks the first IP address. It checks only the following IP address if one has failed.

  I hope it's clearer now

  Rating of useful answers is more useful to say "thank you".

• Windows Server 2008: WDS error when you try to approve the device to capture image.

  I'm taking a laptop that I have on my desk and it captures is currently running 'C:', which I can deploy it to 20 laptops more.

  I did the Audit mode and install and uninstalled the software required for the business and also have SysPreped machine use OOBE.

  I am approving the device sideways server so that I can do the live image capture and put it in the storage of images on the server to deploy on.  I get the same error when I try to join and approve this device on the server.

  Configuration information
  Server: HP Windows 2008 R2 Ent.
  Laptop: HP Windows 7 SP1 64 bit
  Office: Lenovo Windows 7 SP1 64 bit

  Error information
  Log name: Application
  Source: BINLSVC
  EventID: 524
  Level error
  User: n/a
  Task category: BINLSVC
  Keywords: Classic

  Error text (the machine MAC = XXXXXXXXXXXX)
  _______________________________________________________________
  --------------------------------------------------------------------------------------------------------------

  An error occurred trying to create the computer account for the following device:
   
  Name: HPTESTLPTP
  OU: CN = Computers, DC = esc, DC = local
  MAC address: 00000000000000000000XXXXXXXXXXXX
  GUID: B4F2B8E7FBA1E2119673CE39E75C6B08
   
  Information about the error: 0 x 57
  _______________________________________________________________
  --------------------------------------------------------------------------------------------------------------

  Hi Daniel,.

  The question you posted would be better suited for COMPUTING public Pro on TechNet. I would recommend posting your query in the TechNet Forums to get help:

  TechNet Windows Server general forums

  Let us know if you need help with Windows related issues. We will be happy to help you.

• Problem connection ASA 5520 GANYMEDE

  I'm just confused at this point. This is the configuration I have so far for the configuration of Ganymede on ASA 5520. SH run

  ?

  1 2 3 4 5 6 7 8 9 10 11 12 13

  aaa-server TacServer protocol tacacs+aaa-server TacServer (LAN) host 172.19.0.226key ***** user-identity default-domain LOCALaaa authentication telnet console LOCALaaa authentication http console TacServer LOCAL aaa authentication ssh console TacServer LOCAL aaa authentication enable console TacServer LOCALaaa authorization command TacServer LOCAL route LAN 172.19.0.0 255.255.255.0 172.30.186.1 1

  After that I was done with the Setup, I was able to connect using my username tacacas and the password you + activate password.

  After that, I closed my GANYMEDE server + to try to the local database. It worked for the user name and password but my password enable does not work locally. Got to be something very simple and he had written down, I was connected via the cable from the console and also changed it was completely with the user name and password but still not able to go into enable mode.

  After that failed I returned and turned on on my server TACACAS. When to wait a few minutes and trying to connect via tacacas NO GO. He doesn't like my username and password.

  So now I'm locked out and have to do password recovery because I can not connect using tacacas, and when tacacas is off I can not go in the local mode.

  Very litle documentation cisco out there for this issue... Any thoughts what coukld be the cause? I know that GANYMEDE works very well since he works on 500 + devices, I'm just confused at this point.

  I need to check a few things before recovery of password:

  To activate question, try typing the login: follow-up of your user name and password.

  For Ganymede number:

  1.] error on the section of logging of the server Ganymede while accessing the credentials of Ganymede.

  2.] was there any problems reachbility during this time?

  3.] all services came fine?

  4.] should focus on debugs following:

  debugging Ganymede

  Debug aaa authentication

  I'm not sure if this can be replicated, but yes love to help out if possible.

  Jatin kone

  -Does the rate of useful messages-