ADSL ROUTER

Similar Questions

• EA4500 + ADSL router: networking noob question

  Then... I'm not sure of the right words to use, but this is the case I would appreciate the help. I tried to figure out how to survive myself, but I find it a little confusing - however, if you think I just need a networking 101 do not hesitate to send me to appropriate information sources (I've tried a few, as I say, but I have not yet found a place where my situation fits!).

  Quick back story: I have a cheap TalkTalk ADSl router (D-Link 3680) where the Wireless does not properly in the House. So I just got a DSL EA4500 router for better strength/speed/compliance wireless - you'll just have to forgive me for not having an ADSL router, which I realize may have been a simpler solution!

  First of all, I put the (D-Link of TalkTalk 3680) ADSL router in Bridge mode and got this and the EA4500 work together which was great as it goes. However, I would be hard...

  I have a tower PC and wish to receive wired ethernet network. While I know in the set - up above I can run a cable from the 3680 to the EA4500 and then another cable to the PC because the PC is closer to the telephone (with the ADSL router) Jack, physically it seems wiser, if I take the PC of the 3680 ethernet connection (along with a second cable 3680 to EA4500 connection for the wireless). It may or may not be relevant that the 3680 is a Fast Ethernet output, as is the network PC card (i.e. are not Gigabit).

  I don't know (a) whether the above configuration is possible and if yes, how, or (b) the question whether in terms of networking, it is best to cable to the EA4500 computer (even if this will create a longer path to the PC and the wiring more).

  Meaning, and if yes maybe someone could give me also a term for what I'm doing?

  Help gratefully received! Garreth

  3680 port LAN (bridge) => EA4500 Port WAN (router)-online PC peripherals and wireless

  It's the best configuration and nothing should be connected to the 3680 other than the EA4500.

  The physical location of the electronics is not important, unless you can not run cable or wireless signal is low.

• I need help to set up the linksys adsl router

  Hello world!

  I have LINKSYS WIRELESS - N HOME ADSL2 + MODEM ROUTER (wag120n) and I connect to the internet via the cable that I took my friend who already SPEEDTOCH ADSL ROUTER, I bought the d-link wireless card and I install it in one of my PC
  what I need is to set up my linksys wireless router for my two PCs, on via the wireless and another an ethernet cable, how can I do?

  thanks4all

  Follow this link to configure the router.

• I have windows vista business edition is installed on the desktop and Vista home edition on my laptop I can't access files on the laptop and vice versa, I am using a d-link adsl router can u help me solve the issues___Thanks__Peter

  I have windows vista business edition is installed on the desktop and Vista home edition on my laptop I can't access files on the laptop and vice versa, I am using a d-link adsl router can u help me solve problems

  Thank you
  Peter

  Hello

  The easiest way is with a crossover cable - a special wire to connect the two systems.
  You can get one at your local computer store - they are not expensive.

  Also check with the site of the manufacturer of your router, because they will have in-depth details on how to
  set up the network.

  ====================================

  Or you can set up a wired or wireless network.

  Setting up a network home
  http://Windows.Microsoft.com/en-us/Windows-Vista/setting-up-a-home-network

  Home network, wireless network and computer networking Made Easy
  http://www.home-network-help.com/

  Windows Vista tip: How to install and connect to a wireless network
  http://www.watchingthenet.com/Windows-Vista-tip-how-to-Setup-and-connect-to-a-wireless-network.html

  Ad-hoc networking
  http://windowshelp.Microsoft.com/Windows/en-us/help/0e158c21-4C70-4235-879d-0c9133218e561033.mspx
  Set up a computer-to-computer (ad hoc) network
  http://windowshelp.Microsoft.com/Windows/en-us/help/293c504f-b944-4d5d-835c-f080129bd5dc1033.mspx

  How to set up an Ad Hoc wireless network in Windows Vista
  http://www.home-network-help.com/ad-hoc-wireless.html

  Create an ad hoc WiFi network secure on Windows Vista
  http://www.Intel.com/support/wireless/WLAN/sb/CS-025386.htm

  Networking tutorial home
  http://www.tehnomagazin.com/computer/home-networking-tutorial.htm
  Practically networked - everything you could possibly want to know.
  http://www.practicallynetworked.com/

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• PIX and ADSL router.

  I have, in a site, a PIX 515 connected to a C827H (an ADSL router as PPPoE). This router provides access to the Net. In another site, I have another PIX (a 506) and another router C827H which gave access to the Net. Both sites have access to the net without problems. But when I have what it takes to establish a VPN (Ipsec) tunnel between the two sites, across the Net, I can t make the connection. The ADSL router has their public IP is negotiated with the provider. In my lab, I simulate this two connections put two PIX (a 520 and a 506) back to back with a crossover cable. I used the same configuration. The thing worked. But in my two sites that does not work. Why?

  I see, in this case. I suggest that change you the name of the ACL defined in crypto card, try not to use the same ACL you used for nat0, it poses problems sometimes.

  Try and see if it works for you.

  -Jimmy

• How counfigur tp-link router wireless? I have the Wireless ADSL router. I want to add 1 wireless router in this system. What can I do? Please, I beg you. suggest me. ___thank

  1. to configure the router wireless in a network?
  2. I want to set router adsl on a network. How can I do?

  1. to configure the router wireless in a network?
  2. I want to set router adsl on a network. How can I do?

• Windows Vista Home Basic 'local only' access via ADSL router, broudband

  Hello

  I've set up a new router broadband wireless ADSL to connect to my broadband PostOffice.com existing Standard.

  The router is a Belkin F7D1401uk Surf N150 model.

  It is facing up and running and I can use other machines to connect to the internet through it. A netbook running Windos XP SP3 and a mobile phone (Nokia X 6), but my laptop main running Windows Viast Home Basic SP2 (32 bit) do not have wireless internet access.

  It is a Fujitsu Siemens Amilo Li 2727 laptop. If I connect to the new Belkin router using an ethernet cable, I can connect to the internet. But when I unplug the ethernet cable and turn on the WiFi I see a connection to the modem Belkin Wireless, but on an 'unidentified network' and with 'local access' only.

  Here is a copy of what I get when I run "ipconfig/all" at the command prompt:

  Windows IP configuration

  Name of the host...: Clare-PC
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.
  ... DNS suffix search list: Belkin

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. : Belkin
  ... Description: Atheros AR5007EG Wireless Network adapt
  Physical address.... : 00-16-44-E8-64-2C
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::4d89:e63c:ba6c:1c4d % 11 (Preferred)
  IPv4 address: 192.168.2.3 (Preferred)
  ... Subnet mask: 255.255.255.0.
  Lease obtained...: April 3, 2011 15:59:55
  End of the lease...: May 11, 2147 00:41:44
  ... Default gateway. : 192.168.2.1.
  DHCP server...: 192.168.2.1.
  DHCPv6 IOOKING...: 268441156
  DHCPv6 DUID customer...: 00-01-00-01-13-A7-2B-7F-00-1F-16-00-9E-C4
  DNS servers...: 192.168.2.1.
  NetBIOS over TCP/IP...: enabled

  Ethernet connection to the Local network card:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. : Belkin
  Description...: Realtek RTL8101E Family PCI - E Fast Ethernet NIC (NDIS 6.0)
  Physical address.... : 00-1F-16-00-9E-C4
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 7:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 02-00-54-55-4E-01
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 12:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. : Belkin
  ... Description: isatap. Belkin
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  So, it looks to me that use wireless I have an IP address and the default gateway and DNS servers are correct.
  But I do not understand why I "local access" only.

  Can anyone suggest what I can do to get my laptop connected wireless to the internet please?

  Kind regards
  David

  Hello Ttard,

  Thanks for your post.  One of the solutions, I saw about this problem is to go to your system manufacturer's Web site and download / install the latest driver for your computer wireless.

  This thread is very long, but has some great troubleshooting in steps.

  Please let us know if this information helps with your problem.

  See you soon

• establish the GRE/IPSEC behind ADSL router

  Hi all. This is my first post. I watch a lot to the internet so I can't find any help on this problem.

  I would like to set up a VPN with ACCORD between 2 sites, but one of them is behind a router ADSL. This router redirects all external traffic to the external interface of the router.

  The problem is that I don't know how to configure this router because only to see the crypto ipsec his you can see Start local crypto is 192.168.0.147

  and the other router to assign this IP address to complete the second phase.

  I hope that this has been explained clearly.

  Thank you very much experts!

  The problem is so much simpler if your GRE and IPSec endpoint termination ends on the same interface without NAT.  However, things get a little tricky when you have NAT involved.  In this situation, the following the following configuration example:

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a0080094bff.shtml

  I labbed this place many years and it works very well

• ADSL router 1941W - get customers connected to internet wireless

  Hello, hoping that someone can help me, I have 99% of the made config however do not know why wireless clients do not connect to the internet, its lack of im probably something very simple!

  The access point has been implemented, wireless network is in place and ongoing execution, clients can connect, receive IP via DHCP addresses (10.0.16.20 - 30)

  and can ping Vlan 1 (10.0.16.254) and Gi0/0 (10.0.15.254).

  The PPPoA DSL has also been implemented and is connected, the router can access the internet.

  What I want is for wireless clients access to the internet, but also for wired clients (connected to a switch which connects Gi0/0. Cable customers receive IP via DHCP addresses (10.0.15.20 - 50), and these also need access to the internet.

  The router configs and AP are attached, this is what im missing? Thank you.

  Add the VLAN 1 interface,

  IP nat inside

  HTH,
  Steve

  -----------------------------------------
  Please don't forget to rate helpful messages and mark the questions answers

• Microsoft VPN client through 857 router ADSL

  Hello

  I've set up an adsl router 857 with CP Express (web interface) with a standard firewall and NAT configuration.

  router seems to work very well apart from connections outbound pptp.

  I can't use the MS VPN client to connect to our PPTP server in a remote location. I don't try to use VPN on the router 857, allow just to pass through of my laptop computer behind the router to an external vpn server.

  Instantly, the client goes to "Check Userbane and password" then crashes on this during a minute or two before failing.

  Any suggestions would be apprecated.

  Thank you

  Gordon

  Hello

  Try this.

  http://www.Cisco.com/en/us/Tech/tk827/tk369/technologies_q_and_a_item09186a00800946ef.shtml

  and this

  http://siskiyoutech.com/blog/?p=78

  Finally, that

  http://www.Cisco.com/en/us/Tech/tk827/tk369/technologies_configuration_example09186a00800949c0.shtml

  Finally I would like to know this help and write it down.

  Rgds/DP

• Cannot connect my Satellite L500-1WG to Wi - Fi router Netgear

  Hello

  I hope someone can help as Im pulling my hair out. Just replace an old Wireless ADSL router/modem to a "n" wireless Netgear DGND 3300 range Max Dual Band router ADSL. Everything is connected by ethernet to my Office PC Ok. Just bought a laptop L500-1WG with 'n.' compatible wireless card

  Hope to connect to the 802 1.1n 5 Ghz to speed things up and increase will however the laptop cannot find the adapter 2.4 Ghz 'G' and its driving me wild! Ive downloaded the latest drivers and checked in the device manager that "n" is selected. I messed around with the settings of the modem to the router and it seems to all be OK but can not connect, someone at - it ideas? Thought I would have the ability to connect via G or N...

  Your help is appreciated...

  And what is with the settings of the WLAN router? You are using auto option or you have assigned it N only?

• How do I reinstall tp link router for netbook

  I accidentally deleted my router8901G TP Link of my netbook.

  How can I reinstall it?

  zandk wrote:

  I accidentally deleted my router8901G TP Link of my netbook.

  How can I reinstall it?

  You did not remove "my TP Link my netbook router8901G". You may have removed the internet connection or the software of the router TPLink control from laptop installed programs.

  You have two choices. Establish an internet connection for the netbook through the operating system, which you did a secret from us, or reinstall the software of the router TPLink. You can install the software configuration to go drive the router came with or the download from TPLink.

  You can have meant a TD-W8901G ADSL router. TPLink does not manufacture a router TPLink 8901 G.

• Down line ADSL X 3000

  Hello

  I have ADSL router Linksys X 3000, but I have a problem with it. I have it configured correctly (based on the manual of the internet service provider), repeatedly checked, but the router always said that ADSL line is down. I also have another router from Zyxel and it works perfectly with the same yarn and configuration, so I guess that the line is very good.

  There the router log, can someone help me, why the router is not connecting, please? Thanks for any help

  PPP pilot generic version 2.4.2 79
  Deflate Compression of PPP module part 88
  PPP BSD Compression module part 84
  PPPoL2TP kernel driver, 75 V1.0
  ccp_autowan_sm_thread => starts in unconfigured mode, detection of State! 125
  -> State disconnected! 78
  xDSL G.994 training 74
  -> detection of State! 75
  -> dslWanSt = 1, ethWanSt = 0 81
  -> Training RJ11 condition! 79
  ADSL G.992 started 73
  Analysis of channel ADSL G.992 82
  DSL link down 69
  -> State of bottom-disconnected! 83
  -> detection of State! 75
  xDSL G.994 training 74
  -> Training RJ11 condition! 79
  ADSL G.992 started 73
  Analysis of channel ADSL G.992 82
  DSL link down 69
  -> State of bottom-disconnected! 83
  -> detection of State! 75
  xDSL G.994 training 74
  -> Training RJ11 condition! 79

  As another modem (zyxel) works already then I agree that the adsl line works. After you have updated the firmware, you did another reset on the gateway and reconfigure the settings? If not yet, first try another reset and reconfiguration. If it always connects after the reconfiguration, so I think it's a hardware problem.

• Configuration of a router in my house to extend second internet (WRT54Gv7)

  Hello

  I try to set up a second router in my house to provide the internet a couple of computers + wifi I have in the garage

  A main router is ADSL router, which offers 4 ports LAN and WIFI (wifiA) and I have a cable from the router to the garage. This main router has the 192.168.1.1 address.

  In the garage, I want to install a WRT54gv7 to extend internet at two computer and extend the reach of wifi. I want to use the router as a bridge, so all computers (those connected to the main router and connected to garageRouter are in the same network)

  I see that the WRT54G is version 7, as this particular model, it cannot be installed an OpenWRT.

  I can remember, I should then configure the router as:
  -LocalIP address: something like 192.168.1.102
  -Server DHCP: disabled to allow th eDHCP the main router server takes place,

  And this should be everything, isn't it?

  But that does not work, once I connect the wire from the mainRouter to the garageRouter, not only I don't have internet access, but also I lose the avaliability to connect to the garageRouter

  Should I set up as a choice to "Automatic DHCP Configuration"?
  Then are available: 'Static IP', 'PPPoE', "OCDP", etc...

  Note: I have the router form old firmaware v7.00.4 update v7.00.8 build 008, but it makes no difference

  Follow this:

  http://www.Northshore-it.com/Tips/how-tos/cascade_linksys/#LAN_to_LAN

• Client disconnection from the 887VA-W router WiFi

  Hello

  I have several pc, Mac and smartphones all connection with happiness to the AP embedded (AP802) of a router 877va-w, outside of a pc (Samsung Ativ book 9 lite) who guard disconnect and reconnect every few minutes. The ssid is configured for WPA2 with AES and it is immaterial that the ssid is invited or not. The AP is configured to 3 SSIDs and disconnects it from happening on any ssid pc joins. The pc wireless adapter is a Qualcom Atheros AR956x with the latest driver available. I've disabled all saving mode on the customer card and assured that it will run on the maximum power when executing a pile. The same problem occurs if I join the pc via wifi to a 877W router, but not if I connect to a wifi BT Hub2-wireless adsl router.

  Can some advise that I might need to configure Cisco access point in order to ensure the Qualcom AR956x Atheros client remains connected. The State of some newspapers that the Station has left the BSS.

  TIA, Tim

  Each customer is different... so it must always make exceptions for the poorest customers there.  That's the problem with Apple devices in the network for years.  That's why always test you with an open first ssid to eliminate the problem of the customer, then you configure wpa2/aes psk with base put... little by little you add on until failure.  Everything simply because it works now, won't say when a new device to get on the network a year later, that your configuration will not change to support this device.

  It's like the timer of the session on the WLC... many devices dislike the short session timer and being generally disabled and resolved for 24 hours corrects many questions.

  Scott