Agilent 4156 bug or Labview driver bug?

Similar Questions

• Agilent 4156 new driver plug-and-play (pulse-installation problem)

  Hello, I am new to Labview and just started using the Agilent 4156 new plug-and-play driver published on 02/12/2008. I try first to set up conditions of STRESS using this project. While I am able to configure most of the things that I need, I can't set the peak pulse value using the program "Set Pulse.vi". The Readme for the driver mentioned that this program has not been tested. The error message is the following:

  Reports of the instrument:
  + 181, "illegal installation. Invalid command. »
  -113, "undefined header."
  + 0, "no error".

  Can someone help me with this problem?

  Thank you.

  Thanks for your reply.

  I think I solved the problem. There are syntax errors in the "set up" Pulse.vi (PUL has been used instead of PULS in two places). He is now able to set the basic and advanced.

  In addition, the way is designed the vi, it will always give an error because he tries to put in tension (possible only when a VIEW is of type V) 'Source' and 'Base' / 'Peak' tensions (only possible when the PGU is a type VPULSE). I removed the parts that I didn't need.

  FYI, I use an Agilent 4156 C. In the configuration screen, the revision of the CPU is 1 and the revision of the software (03.06 HOSTC, CUMS 04.07, ADC 01.00).

• LabVIEW driver for agilent 8720ES S-parameters network

  Hello

  Is it possible to get the labview for agilent 8720ES S-parameters network driver? I need this driver to communicate with the Network Analyzer?

  Thank you

  Concerning

  Mayuren

  Hi Mayuren,

  OR keep a number of drivers on their website called instrument driver network at www.ni.com/idnet and it contains the drivers put at our disposal.  The driver for your product is available here at the http://sine.ni.com/apps/utf8/niid_web_display.model_page?p_model_id=1618.

  Kind regards

• You use HP 4156 instrument with Labview 2010 in Windows 7

  We recently bought Labview 2010 for Windows 7 and some software porting, we had on Labview 6.  These programs of control of two instruments: HP (Agilent) 4156A parameter Analyzer and the Keithley 7001 switch system.  When I looked for the drivers of instruments for these two systems, they were no longer available for Labview 2009 and associated NI-VISA 3.2 driver is not compatible with Windows 7.  You have any suggestions on how we can run Labview 2010 on Windows 7 with the ch (Agilent) 4156 A and Keithley 7001?

  A pilot in 2009 can be loaded in 2010 and this is the minimum VISA version, you can use. You need not even the driver of instruments most recent. Just run your existing code.

• .exe for labview driver

  I run an .exe driver for laser Doppler vibration. I want to use in lab mode

  or convert LabVIEW driver because the manufacturer donot have any lab display driver

  can someone please help how to do that

  Deutchland wrote:

  I have some commands to it. communication is via ehernet

  Make your own driver using VISA or TCP/IP functions.  You have just need to know what commands to send, and how the data will come back.  Once you make the connection and read the manual, it should be simple enough to make a decent driver library.

• How to set the parameters of the AKD with LABVIEW driver?

  Hello

  I am looking for a simple example to set or read the AKD with Labview driver settings.

  The AKD has ethernet communication and control is analog - AKD-P00306-NBAN-0000

  I want to use Labview to read the paramerters even as Kollmorgen WorkBench

  Thanks for your help

  Thank your for your help

  I found a solution with the TELNET Protocol

• Inconsistent behavior with Ocean Optics LabVIEW driver

  Hello

  I noticed an odd behavior when using the USB2000 Ocean Optics spectrometer. When I use the driver tools read the waveform, I get a waveform of pixels in length 2022. When I use the Ocean Optics (SprectraSuite) software I have a waveform of length 2048.

  I first noticed this problem when I was looking at the spectrum of a light source that is known to be ~ 870nm. Using the LabVIEW driver, I saw a peak at ~ 857nm, but using the Ocean Optics software, I saw a pic to 870nm as expected. Please let me know if you can give no indication to this problem. Thank you

  Gregory

  Just to be tied it on, I don't end up the front of the table of the spectrum with zeros to fill. It's certainly something that would deal with Ocean Optics (or the writer of the drivers). I do not change the driver because he could shoot me in the foot when you use one of the other patterns.

  Also, I noticed that for the USB2000 Set integration time VI, the time units are milliseconds. The USB4000 (and what is suggested by the drivers/examples) use the microseconds.

  Hope that these drivers can get an update soon!

• Tektronix TDS2014C 2012 Labview driver

  Hello, I have to deal with the problem of communication with the PC with LabView 2012 new oscilloscope. I downloaded all the drivers site Web

  http://sine.NI.com/apps/UTF8/niid_web_display.download_page?p_id_guid=047216EC20B66FABE0440003BA7CCD...

  and it seems that none of them work. TDS2014C is connected via USB and I am running Windows 7. In the control panel - Device Manager I see this device but to run without a driver, so there is some sort of error. I tried to find any other device just for Windows, but there is no driver. So please help me with this problem of TDS2014C drivers running on my computer in LabView.

  Until I reinstalled LabView for 2012, it worked, but now, no, I don't know if it is possible because the new version of LabView it stopped working (a previous version of LabView was 2010 SP1).

  OK everything is solved, the guys at tektronix has helped me. I have their answer qote:

  With usb connections measuring instruments use USB - TMC to communicate, if you need a usb - tmc driver to get the highest level parts labview to work.

  You can find one when trying to install TekVisa, or by installing the appropriate components of NI-Visa.

  Then you can try to hit these urls to:
  http://digital.NI.com/public.nsf/allkb/044FA220F32774ED86256DB3005850CA
  or
  http://www.Tek.com/oscilloscope/tds7054-software/TekVISA-connectivity-software-V400

  (I do not use Labview myself, but looks like it is the piece that you miss).
  Byron

• Labview driver Giga-tronics 12000 has

  Driver giga-tronics 12000a labview someone knows where I could find this driver thank you

  double post

• Agilent Power Supply E3645A IVI Driver Communication error

  Hello world

  I'm trying to communicate to Agilent power using IVI Drivers. I join you MAX Report, all the modules installed on the system.

  When I run initialization of the VI for Agilent power, using the simulation with 'Specific Driver', no errors appear. But when I select "do not simulate", I get this error:

  Initialize IviDCPwr with Options.vi
  The primary error: (Hex 0xBFFA0011) function or method not supported.
  Development: FunctionId: 3, FunctionName: InitWithOptions

  Communicate with instruments instrument using Driver works fine, but using the Drivers IVI is not.

  I tried all the steps in this topic .

  PROMT any help will be highly appreciated.

  Kind regards.

  Shane5ab

  Hello, Tanguy,.

  I am pleased that install the specific instruments IVI - C Driver took care of things.  The differences between IVI - C and IVI - COM can be confusing at first.  I hope the rest of your application development goes smoothly.

  See you soon,.

  NathanT

• GW INSTEK LCR819 LabVIEW Driver

  Hi everyone on the forum

  I'm looking for the driver for a GW Instek LCR 819 LabVIEW.

  I had searched the internet ther with no luck, even the seller has not

  Wonder why?

  Is currently working on the ATE to a Senor (aeronautical) oil level

  Someone used before...   LabVIEW 2012

  Best regards

  You must add a termination character to the chain of command. Normal display setting, you cannot add special characters. The value default of '-' display Codes for special characters. For example, \r for carriage return or \n for a new line. The characters of termination for your instrument are a little weird. Instead of trying to use ' \' Codes, it may be easier for you to use the string function of concantanate on the block schema to add the characters of endpoint as a string constant. I would say that this constant of string to hexadecimal display or by using an array of U8 to enter decimal/hexadecimal values, the stop character, then a byte array to a string.

  Before doing all this, have you tested the communication with a program such as Hyperterminal terminal emulation?

  Edit: I should have looked up those scan codes before you answer. A ctrl J is a newline (\n) and ctrl M CR (\r) so back to the control of the chain to '-' Codes and add \n\r. You can also try of \r\n.

• Agilent 488.2 with Labview

  I have an Agilent 82357 B USB GPIB and have provided the code that uses GPIB read and write functions. I have installation OR MAX and Agilent connection Expert correctly. The program doesn't error but write and read timeout functions and does not work. I troubleshoot wrote simple code using VISA and they work. I wrote the same code using the GPIB functions and it does not work and after I run code written in VISA no onger work. I know that Agilent replaces the gpib - 32.dll with their version which redirects to their code.

  My question is, is there anyway to make the GPIB LabVIEW calls working with Agilent GPIB device and of course library GPIB? I think that the answer is, but I saw a post where someone said they do. I want just a definitive answer until I give the bad news.

  While there were some vendors implementing their GPIB drivers with the same function calls or use (ibwrt, Bird, etc.). I don't think Agilent has already done this and I used the maps of Agilent since the time they were still Hewlett-Packard. I'd love to see the post where somebody said, they could use the LabVIEW GPIB functions with a controller of Agilent.

  So, the answer is not to my knowledge. What you need to do is to use VISA. Enable Tulip support NOR-MAX and it should work.

• How can I create a LabView driver with vi existing driver?

  I am trying to create a driver for LabView 1553. I received the previously created driver files LabView 1553 of the manufacturer. I also used tools-> Instrumentation-> create an Instrument pilot project to start a new project. I used a new model and the block is now under Instrument i/o. I moved all the files previously created 1553 driver in the data folder in the project located in C:\Program File\National Instruments\LabVIEW 8.6\1553Data\Public\Data.  I don't see any of the vi driver is available to the title of the Instrument I / O-> 1553Data. How can I make these usable vi?

  Also, I'm not sure my files folders should go in (configuration, data, utilities, etc.).

  Thank you.

  I thought about it. Here's how to insert the vi in the palette:

  Tools-> Advanced-> Edit Palette Set

  I went into the data section and right click. There is a possibility to insert VI. I clicked on it and took my vi to insert and now it manifests.

  Thanks for your help.

• NI LabVIEW driver for the SRS DS345 function generator generates error "(Hex 0xBFFF0011) insufficient location information or the device or resource is not present in the system."

  Hello

  We have a generator function SRS DS345.

  I just downloaded the driver NOR for the instrument on http://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=E3B19B3E9149659CE034080020E748....

  After installation, the DS345 appears in MAX, and I can well communicate with him.

  However, if I run the srds345 to Started.vi, I get an error "location information insufficient (Hex 0xBFFF0011) or the device or resource is not present in the system" from initialize it with Options.vi srds345 sub - vi.

  The only change I did Exchange address GPIB 14 to 19, which is our function generator GPIB address. In addition, the

  Functions of SRS DS345 generator of function palette is empty, even after you restart LabVIEW (see attachment). I'm using LabVIEW 8.5.1.

  Your help in resolving this issue is appreciated. Thank you.

  Best regards

  Peter

  Have you installed the driver from LabVIEW or copied directly from inst.lib?

  The first is easier, and you don't have to restart LV more...

  Error in a not filled gpib address points. I have not checked if this driver has a resource name visa or a string of gpib address old but in the first case, try the little triangle on the right at the slect address instead of by hand.

• What should I do to make my gear compatible LabVIEW (driver development)?

  I work for a manufacturer of industrial automation products. We create a new data recorder and we want to make it compatible, LabVIEW, so that users could easily use our product of LabVIEW. Our device will have series (RS-485) and Ethernet interfaces.

  Do we not have to develop any kind of driver? Do we not have to subscribe to any program of 'partnership' with NEITHER? Where can I get information on how to proceed?

  Best regards

  Sandro

  Take a look on: http://www.ni.com/devzone/idnet/